Search NASA⌕ Search

SEARCH · Search NASA

Results for “Trade”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Laser ablation of high-loading Li-ion battery electrodes improves accessible capacity and cycle life for Behind-the-Meter Storage

Adoption of Behind-the-Meter Storage (BTMS) requires design of batteries that enable high safety, long cycle life, and low cost at the system level. Pairing Li 4 Ti 5 O 12 (LTO) with LiMn 2 O 4 (LMO) achieves targets related to safety and cycle life, but these materials' low energy densities contribute to higher cost at the system scale. Increasing electrode loading is a simple approach to improve energy density, but comes with a trade-off in electrode utilization due to long, tortuous Li + diffusion pathways. Here, laser ablation is used to microstructure (pattern) high-loading electrodes to enhance electrode performance through improved Li + diffusion pathways. Four cell types, comprising combinations of standard or patterned anode and cathode, were prepared to evaluate the effects of laser ablation at each electrode. A rate test shows that patterning electrodes enhances active material utilization at ≳1C rates. Patterning the cathode yields the most benefit, as cells with a patterned cathode demonstrate a ~20% higher accessible capacity than those without at 1.4C. Additionally, 1C capacity retention of cells with patterned cathode (91% through 3000 cycles) is significantly improved over cells with only the anode patterned (64%) and non-patterned electrodes (50%). Characterization of post-mortem cells before and after refreshing their electrolyte suggests that 1C capacity retention is improved by mitigation of electrode "dry-out". We hypothesize that the microstructure acts as a reservoir of additional electrolyte, or a path for gas to escape, so that active material remains wetted throughout long-term cycling, and/or the microstructure may reduce localized, gas-forming overpotentials in the high-loading electrode.

25 ENERGY STORAGE↗
DOE OSTI2020

Multiscale model predictive control of battery systems for frequency regulation markets using physics-based models

In this work, we propose a multiscale model predictive control (MPC) framework for stationary battery systems that exploits high-fidelity models to trade-off short-term economic incentives provided by energy and frequency regulation (FR) markets and long-term degradation effects. We find that the MPC framework can drastically reduce long-term degradation while properly responding to FR and energy market signals (compared to MPC formulations that use low-fidelity models). Our results also provide evidence that sophisticated battery models can be embedded within closed-loop MPC simulations by using modern nonlinear programming solvers (we provide an efficient and easy-to-use implementation in Julia). We use insights obtained with our simulations to design a low-complexity MPC formulation that matches the behavior obtained with high-fidelity models. This is done by designing a suitable terminal penalty term that implicitly captures long-term degradation. The results suggest that complex degradation behavior can be accounted for in low-complexity MPC formulations by properly designing the cost function. We believe that our proof-of-concept results can be of industrial relevance, as battery vendors are seeking to participate in fast-changing electricity markets while maintaining asset integrity.

42 ENGINEERING↗
DOE OSTI2022

Montage electron tomography of vitrified specimens

Cryo-electron tomography provides detailed views of macromolecules in situ. However, imaging a large field of view to provide more cellular context requires reducing magnification during data collection, which in turn restricts the resolution. To circumvent this trade-off between field of view and resolution, we have developed a montage data collection scheme that uniformly distributes the dose throughout the specimen. In this approach, sets of slightly overlapping circular tiles are collected at high magnification and stitched to form a composite projection image at each tilt angle. These montage tilt-series are then reconstructed into massive tomograms with a small pixel size but a large field of view. For proof-of-principle, we applied this method to the thin edge of HeLa cells. Thon rings to better than 10 Å were detected in the montaged tilt-series, and diverse cellular features were observed in the resulting tomograms. These results indicate that the additional dose required by this technique is not prohibitive to performing structural analysis to intermediate resolution across a large field of view. We anticipate that montage tomography will prove particularly useful for lamellae, increase the likelihood of imaging rare cellular events, and facilitate visual proteomics.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2026

Material-dependent photon ionizing radiation effects in Si and GaAs PIN diodes: A numerical investigation

We present a finite-element drift-diffusion-Poisson model in the Multiphysics Object-Oriented Simulation Environment (MOOSE) framework to compare the radiation response of silicon (Si) and gallium arsenide (GaAs) PIN diodes under high-energy photon irradiation. The model solves coupled carrier continuity and Poisson’s equations with Shockley-Read-Hall recombination, and is verified against standard analytical J-V behavior. Using a simplified 1D geometry with ideal Ohmic contacts, we quantify device response under forward and reverse bias with a 100 MeV photon flux. Under forward bias, Si exhibits markedly greater radiation sensitivity than GaAs, including larger increases in current density, stronger local field and carrier-product perturbations, and higher recombination. Under reverse bias, GaAs shows larger radiation-induced photocurrent and broader current-density peaks near junctions, indicating an advantage for photodetection. Integrated steady-state recombination is consistently higher in Si across voltages. Under periodic photon pulses, GaAs produces higher-amplitude photoresponse and settles more rapidly than Si. These results highlight material-dependent trade-offs for radiation-tolerant, high-speed optoelectronics and provide guidance for selecting PIN architectures in aerospace, nuclear, and high-energy physics environments.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Fabrication and accelerated long-term stability test of asymmetrical hollow fiber-supported thin film oxygen separation membrane

Asymmetrical hollow fiber-supported thin film membrane may provide microstructural advantages for air separation and oxygen production. The fabrication of such a membrane is usually very difficult, particularly the sintering behaviors and thermal expansion coefficient (TEC) mismatch among multiple layers. This directly affects the reliability and long-term stability of the membrane. Here, in this research, the sintering behaviors of a set of simple oxides are systematically studied and ZnO is identified as a material component for composite substrate La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ (LSCF)-ZnO. The LSCF-ZnO ratios are further optimized by trading off several factors, e.g., matching the sintering behaviors and TECs of the LSCF-ZnO composite with those of LSCF thin film separation layer while enhancing the substrate strength. With the identified LSCF-ZnO ratio, the LSCF-ZnO composite hollow fiber substrate precursor is formed through slurry spinning process with porous microstructure being formed via phase inversion process. The thin film LSCF dense separation layer is then dip-coated on the substrate followed by co-sintering process. A thin, porous PrBaCo(Fe 0.6 Zr 0.2 Y 0.2 )O 5+δ (PBCFZY) catalyst layer is fabricated on the dense LSCF separation layer with dip-coating and sintering process, forming an asymmetrical membrane device LSCF-ZnO/LSCF/PBCFZY. Oxygen permeation test of the device is systematically conducted, and the fundamental mechanisms are analyzed. An accelerated long-term stability test of the membrane is also conducted (~550h, 46 thermal cycling loads), demonstrating excellent robustness and durability. The device is characterized and analyzed before and after the test. By replacing a considerable amount of high cost LSCF with low cost ZnO in the substrate, it not only enhances the stability but also reduces the capital cost of the membrane for practical applications.

42 ENGINEERING↗
DOE OSTI2024

Machine learning-guided discovery of polymer membranes for CO 2 separation with genetic algorithm

Designing polymer membranes with high gas permeability and selectivity is a difficult multi-task constrained problem due to the trade-off between these two properties. In this work, we present a machine learning (ML) driven genetic algorithm to tackle the design problem of polymer membranes for CO 2 separation from N 2 and O 2 . Using literature data of permeability for three gases, we constructed multiple ML models with different fingerprinting featurization schemes to predict gas permeabilities. Then, we employed a genetic algorithm to design new polymers and evaluated their performance using our ML models. We were able to identify new polymer membranes that are promising for both CO 2 /N 2 and CO 2 /O 2 separations. Further, the top discovered polymers are predicted to have high glass transition temperatures. Similarly, the pyridine functionality was found in ≈20% of the predicted polymers. This framework can be used to design polymers for any application involving constrained optimization. Finally, we outlined the challenges and opportunities with using ML guided data-driven inverse design of polymers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Effect of stoichiometry and hydration level on water domain size and transport in poly(aryl piperidinium) alkaline anion-exchange membranes

Alkaline water electrolysis holds promise in decarbonizing the global economy by enabling renewable hydrogen production with non-precious group metal catalysts. Anion exchange membranes are an important component of alkaline water electrolyzers and would ideally be durable while allowing for high hydroxide conductivity. The poly(aryl piperidinium) (PAP) class of polymers has attracted recent interest due to their good mechanical robustness and high ionic conductivity. Here, in this work, we perform atomistic molecular dynamics (MD) simulations of several PAP polymers at experimentally relevant hydration levels and polymer ion exchange capacities (IECs) to gain nanoscale insight into their properties and to help elucidate the trade-offs that result from tuning the IECs through the polymer stoichiometry. Our MD-predicted macroscopic polymer properties were found to be in good agreement with experimentally available polymer swelling ratios, water-occupied volumes, X-ray scattering, and ionic conductivities. The models show that for hydration levels greater than 8H 2 O per cation a single water cluster will form that percolates through the system. The growth in water cluster size results in large polymer swelling, the creation of larger channels with widths of 7 Å or larger, and nanophase separation between the hydrophilic domains and the polymer with characteristic length scales of approximately 20–30 Å. The experimentally observed lack of a strong X-ray scattering peak at low wavevectors can be explained by a cancellation between the polymer-polymer/water-water and polymer-water correlations and not a loss in nanophase separation. The overlap in coordination environments of the hydroxide oxygen and polymer nitrogen atoms implies that vehicular diffusion between cationic groups could play a role in hydroxide transport. The polymers' hydroxide and water diffusion constants increase by approximately an order of magnitude between hydration levels of 8 and 20H 2 O per cation. However, there are diminishing returns in hydroxide diffusion constant once the IEC exceeds 2.4 meq/g.

08 HYDROGEN↗
DOE OSTI2020

Implications of post-processing induced microstructural changes on the deformation and fracture response of additively manufactured Ti–6Al–4V

Ti–6Al–4V parts fabricated via electron beam melting (EBM) powder bed fusion are often subjected to hot isostatic pressing below the β-transus temperature to mitigate defects. During which the pressure aids in pore closure and the thermal exposure results in coarsening of α phase while retaining the columnar prior-β phase grain morphology present in the as-fabricated condition. The same post-processing treatment can also be carried out above β-transus temperature which is an effective way to modify both the grain morphology and the associated α textures. Here, the objective of this work is to correlate thermally induced microstructural changes to the deformation and fracture response of the EBM processed Ti–6Al–4V. To this end, we have carried out both sub-transus and super-transus heat-treatments of the as-fabricated material. The mechanical response of the as-fabricated and all heat-treated materials are characterized by in-situ tensile tests under a high-resolution digital optical microscope. This enabled us to capture large-scale panoramic images of the deforming microstructure, and overcome the trade-off between the image resolution and the field of view during in-situ experiments. The series of images captured throughout the imposed deformation are subsequently used to perform microstructure-based digital image correlation to measure microstructural-scale strains over a large area. The results of the in-situ tests together with detailed fractographic analyses are then used to elucidate how the heterogeneous deformation spanning over multiple microstructural length-scales, for example, at the scale of lamellae, colonies of lamellae and grain boundaries, affect the overall deformation and fracture response of the post-processed materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Repurposing the θ (Al 2 Cu) phase to simultaneously increase the strength and ductility of an additively manufactured Al–Cu alloy

The Al–Cu–Mn–Zr (ACMZ) cast family of alloys offers unique properties and value propositions for higher strength, higher temperature lightweight components of future vehicles. Earlier research has demonstrated trade-offs in the selection of the alloy chemistry in which an increase in Cu content from 6 up to 9 wt% improves hot tear resistance but lowers ductility. However, a recent study has demonstrated that higher-Cu (9Cu) ACMZ fabricated with laser powder bed fusion additive manufacturing (AM) results in an increase in both ductility and strength when compared to as-aged microstructure of cast 9Cu alloys. The mechanisms of differing mechanical performance of the cast and AM ACMZ alloys are elucidated in the current paper through the utilization of in situ high energy x-ray diffraction (HEXRD) tensile testing wherein lattice strains of different phases are calculated and correlated to their stresses. The ACMZ alloys consisted of theta (θ) and theta prime (θ') phases (both Al 2 Cu in nominal composition) within an aluminum matrix. The larger micron-size θ phase which decorated the grain boundaries in 9Cu ACMZ cast alloys recorded small lattice strains, while the submicron, homogeneously distributed θ phase in the 9Cu ACMZ AM alloy recorded considerably higher lattice strains. The maximum stress reached in the θ phase for the cast 9Cu alloy was found to be ~280 MPa, which was lower than the AM 9Cu alloy which registered a maximum stress of ~1.4 GPa. These measurements indicate that delayed fracture of the finer intermetallic phases simultaneously improves the ductility and strength of AM 9Cu alloy relative to the cast 9Cu alloy, which exhibits early fracture of the larger intermetallic particles.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Deformation behavior of metallic glass composites and plasticity accommodation at microstructural length-scales

Bulk metallic glass matrix composites represent a unique microstructural design strategy for overcoming the strength/ductility trade-off in structural alloys. Site-specific mechanical behavior of a Ti-based bulk metallic glass composite was evaluated at microstructural length-scale. The micro-pillars on the amorphous matrix showed on average a yield point of 1.9 GPa followed by serrated plastic deformation characteristic of shear banding. In contrast, micro-pillars on the crystalline dendritic phase showed a much lower yield strength of 0.72 GPa on average for the four different crystallographic orientations chosen, smooth plastic flow with no recognizable load burst, and stable strain-hardening after yield point. A number of micro-pillars were made at the interface between the glassy matrix and the crystalline dendrite. The mixed micro-pillars showed homogeneous deformation and greater plasticity which was attributed to their smaller stored elastic energy. Shear bands initiated in the amorphous matrix were arrested by the crystalline dendrite, which accommodated plasticity through slip bands and dislocations pile-ups. The interface remained intact after plastic deformation, with no observable signs of devitrification in the amorphous phase.

Bulk metallic glass matrix composite, Micro-pillar↗
DOE OSTI2025

Optimizing the impacts of solid additives on the operational stability and processing reliability of organic solar cells

Previous reports have revealed that by leveraging solid additives, organic solar cells (OSCs) can surpass the device’s performance beyond the intrinsic limitations of host photoactive molecules, a remarkable advancement. However, the impacts of more complex interactions introduced by solid additives are not yet well understood. Herein, optimizing the fabrication process based on the traditional efficiency-guided approach fails to represent the ideal and most practical devices. In particular, achieving superior operational stability while minimizing the device performance scattering was found to require processing solvent evaporation to be synchronized with the volatility of the chosen solid additive. However, this may be challenging since most organic photoactive materials display excellent efficiencies only with selected solvents. Accordingly, this work also demonstrates the potential of dual and complementary solvents selection, consisting of low boiling point (primary) and high boiling point (secondary). This strategy allows for the suppression of any potential trade-offs in efficiency. Meanwhile, the operational stability and precision of device performance are substantially enhanced. Additionally, solid additives have demonstrated that the singlet exciton dissociation rate does not limit the free charge generation yield. Finally, these findings are expected to reformulate OSC device fabrication strategies towards more practical devices.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Persistent mysteries of jet engines, formation, propagation, and particle acceleration: Have they been addressed experimentally?

Here, the physics of astrophysical jets can be divided into three regimes: (i) engine and launch (ii) propagation and collimation, (iii) dissipation and particle acceleration. Since astrophysical jets comprise a huge range of scales and phenomena, practicality dictates that most studies of jets intentionally or inadvertently focus on one of these regimes, and even therein, one body of work may be simply boundary condition for another. We first discuss long standing persistent mysteries that pertain the physics of each of these regimes, independent of the method used to study them. This discussion makes contact with frontiers of plasma astrophysics more generally. While observations theory, and simulations, and have long been the main tools of the trade, what about laboratory experiments? Jet related experiments have offered controlled studies of specific principles, physical processes, and benchmarks for numerical and theoretical calculations. We discuss what has been accomplished on these fronts. Although experiments have indeed helped us to understand certain processes, proof of principle concepts, and benchmarked codes, they have yet to solved an astrophysical jet mystery on their own. A challenge is that experimental tools used for jet-related experiments so far, are typically not machines originally designed for that purpose, or designed with specific astrophysical mysteries in mind. This presents an opportunity for a different way of thinking about the development of future platforms: start with the astrophysical mystery and build an experiment to address it.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

Compound pulse characteristics of a heterogeneous composite scintillator in a gamma-ray field

An important aspect of radiation detection in scintillators is the time dependence of emitted fluorescence, which results in characteristic measured pulse shape. In some materials, a relatively strong dependence of the scintillation pulse shape on stopping power exists, which can provide reliable identification of the incident particle. An alternative method to realize particle identification is by combining materials with different fluorescence lifetimes into heterogeneous structures. Such composite scintillators derive their properties from both the constituent material characteristics and the geometry of the composite structure. In composite scintillators with a high degree of heterogeneous loading, a superposition of fluorescence contributions originating in multiple materials, which is observed as single waveform with an intermediate pulse shape, may affect its ability to reject rays. We measure the time dependence of light output from a scintillator composed of 6 Li-containing glass shards and scintillating polyvinyl toluene and identify events that exhibit such compound behavior when exposed to rays and fast neutrons. We develop a modeling and simulation framework that reproduces the pulse shapes in heterogeneous scintillators and use it study the effect that the weight percentage of 6 Li glass has on rejection. The modeling framework is applied to the experimentally studied scintillator, finding a good agreement. Here, the developed modeling and simulation approach will help optimize the design of heterogeneous scintillators to meet the desired trade-o between neutron capture efficiency and -ray rejection.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

New segmented target for studies of neutron unbound systems

The study of neutron-unbound systems using invariant mass spectroscopy is often performed using low-intensity radioactive ion beams. Low reaction yields can be countered by using thick targets but at the expense of larger uncertainties in the reconstructed invariant mass. In this work, we present a new segmented target designed to address this trade-off. It is composed of three mm thick passive beryllium targets interleaved between four thick position sensitive silicon detectors. In the first experiment to use this new system the half-life of two-neutron unbound was measured to be (stat) (syst) ps, which agrees with a previous measurement made by the MoNA Collaboration.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Computational techniques for the analysis of small signals in high-statistics neutrino oscillation experiments

The current and upcoming generation of Very Large Volume Neutrino Telescopes – collecting unprecedented quantities of neutrino events – can be used to explore subtle effects in oscillation physics, such as (but not restricted to) the neutrino mass ordering. The sensitivity of an experiment to these effects can be estimated from Monte Carlo simulations. With the high number of events that will be collected, there is a trade-off between the computational expense of running such simulations and the inherent statistical uncertainty in the determined values. In such a scenario, it becomes impractical to produce and use adequately-sized sets of simulated events with traditional methods, such as Monte Carlo weighting. In this work we present a staged approach to the generation of expected distributions of observables in order to overcome these challenges. By combining multiple integration and smoothing techniques which address limited statistics from simulation it arrives at reliable analysis results using modest computational resources.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Synthesis and processing of lithium-loaded plastic scintillators on the kilogram scale

Plastic scintillators that can discriminate between gamma rays, fast neutrons, and thermal neutrons were synthesized and characterized while considering the performance at the kilogram scale. The synthesis and processing of these plastic scintillators on the kilogram scale required examination of several factors. The examination of these factors was necessitated by the inclusion of 0.1 wt.% lithium-6 to enable detection of thermal neutrons. First, methacrylic acid was used as an additive to solubilize salts of lithium-6, which allow for a thermal-neutron capture reaction that produces scintillation light following energy transfer. Second, a trade-off between scintillation performance and processability was considered because the increasing content of the methacrylic acid that aided processability resulted in a sharp decrease in the light output. The use of small amounts of methacrylic acid (≤3 wt.%) resulted in better performance but required high processing temperatures. At large scales, these high temperatures could initiate exothermic polymerization that results in premature curing and/or defects. Additionally, the deleterious effects of the methacrylic acid may be mitigated by using m-terphenyl as a primary dye rather than 2,5-diphenyloxazole (PPO), which has been traditionally used in organic scintillators. Finally, the curing environment was controlled to avoid defects like cracking and discolouration​ while maintaining solubility of dopants during curing. For scintillators that were produced from kilogram-scale batches of precursors, the effective attenuation of scintillation light was characterized.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Dual particle imaging using time-of-flight neutron classification

Fast-neutron imaging technology is well-suited for passive nuclear material monitoring, secondary inspection of flagged cargo, and wide-area search for lost neutron sources. However, imaging systems that use pulse shape discrimination for event classification require complex pulse waveform analysis. In this work, we evaluate time-of-flight (TOF) based particle classification as an alternative solution for fast-neutron imaging by classifying all events with a TOF above a maximum threshold as neutrons. We measured a Cf-252 source next to Cs-137 using a 12-bar organic-glass scintillator array. By varying the TOF thresholds for neutron identification, we demonstrate a clear trade-off between event yield and backprojection image fidelity, with stricter thresholds improving precision at the cost of statistics, TOF thresholded data generated an image that predicted the neutron source direction with 20% reduced mean central angle prediction error compared to a traditional pulse shape discrimination (PSD) method with comparable event count. Time-of-flight particle classification shows promise as an alternative to pulse shape discrimination systems for fast neutron imaging systems looking to minimize costs and size of electronics with comparable imaging quality. The sources used demonstrate that the method is effective in classifying measured neutrons in a measurement environment with 150 μCi Cs-137 and 1.6 × 10 6 n/s Cf-252 sources positioned at distances of 66 cm and 81 cm from the detector. Additionally, the method classifies low-energy neutron events that pulse shape discrimination removes, so a combination of both methods would result in a higher overall neutron event efficiency.

Heriot, William [Univ. of Michigan, Ann Arbor, MI ↗
DOE OSTI2024

Multidimensional modeling of fuel-cladding friction in an LWR fuel rod

Solving finite element problems with friction often increases the level of difficulty to obtain properly converged solutions. This type of challenge becomes more salient when advanced, possibly multiscale, material models are employed to capture the thermomechanical behavior of fuel and cladding materials. Here the present work details our recent developments in a nuclear fuel performance finite element code for the systematic consideration of friction in nuclear reactor finite element simulations. We show the application of friction and its effects on the mechanics of light-water reactor rods accounting for various fuel constitutive modeling techniques, model dimensionalities, pellet assumed geometries, and power conditions. In particular, we focus on the fuel rod mechanical behavior as it relates to fuel constitutive models, sensitivity to the coefficient of friction, pellet states of stress, and rod elongation. We discuss the trade-offs between the various multidimensional modeling options and highlight the relevance of frictional effects in the prediction of the fuel rod deformation and interfacial stresses. To relate our modeling results with actual reactor operation, simulations including frictional effects are compared with fuel rod elongation experimental data and some challenges for carrying out a full validation of the axial mechanics are discussed.

42 ENGINEERING↗