Top-gate organic field-effect transistors fabricated on paper with high operational stability
Not provided.
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Not provided.
The effects of post-deposition CdCl 2 annealing temperature on the electronic properties of CdTe solar cells were investigated. CdTe devices incorporate Mg doped ZnO as a buffer layer and selenization using a CdSe interlayer for reducing the buffer/absorber interface recombination and increasing solar energy absorption respectively. The post-deposition CdCl 2 annealing treatments were done under separate, inert atmospheres of nitrogen and helium across the temperature range 380 to 430 °C. Electrical characterization of devices is carried out including temperature dependent current-voltage characteristics, admittance spectroscopy, and Shockley-Read-Hall recombination analysis. Here, the best improvements in device efficiency are obtained upon annealing at temperature 410 °C. This anneal correlated with reduced back contact barrier in CdTe and reduced grain-boundary barrier height which is beneficial for enhanced charge transport.
Processing organic photovoltaic (OPV) blend solutions with high-boiling-point solvent additives has recently been used for morphological control in bulk-heterojunction OPV cells. Here we show that even low-boiling-point solvents can be effective additives. When P3HT:PCBM OPV cells were processed with a low-boiling-point solvent tetrahydrafuran as an additive in parent solvent o-dichlorobenzene, charge extraction increased leading to fill factors as high as 69.5%, without low work-function cathodes, electrode buffer layers or thermal treatment. This was attributed to PCBM demixing from P3HT domains and better vertical phase separation, as indicated by photoluminescence lifetimes, hole mobilities, and shunt leakage currents. Dependence on solvent parameters and applicability beyond P3HT system was also investigated. (C) 2013 Elsevier B.V. All rights reserved.
A full-field crystal plasticity (CP) framework is presented for the GRCop-42 alloy to study microscopic mechanical behavior and local stress heterogeneities. The microstructures of additively manufactured (AM) materials are often unique relative to conventionally processed materials, and the local thermal histories drive these differences during the build process. These thermal histories depend on the process parameters (laser power, scan speed, and scan strategy) and the part geometry. Prior research has shown that the mechanical properties of thin-walled structures can vary significantly with wall thickness due to changes in the thermal boundary conditions during manufacturing. It is, therefore, desirable to perform CP simulations based on the phenomenological constitutive model to predict the local mechanical responses induced by microstructural heterogeneities. This work generates representative microstructures based on experimentally collected grain information (i.e., texture) for grain scale stress analysis, and the material constitutive parameters are calibrated using the experimental mechanical testing data. Here, we specifically investigated the effect of crystallographic texture and grain morphologies on the size-dependent mechanical properties of AM GRCop-42. The selection of appropriate material properties for implementing an effective free surface boundary condition and the influence of adjacent buffer layers are also discussed. Analysis of local field results reveals a strong correlation between stress localization and the initial grain orientation. However, no significant relationship between the misorientation of the individual adjacent grains and the average misorientation is observed.
The bronze polymorph of titanium dioxide, known as TiO 2 (B), has promising photochemical and electronic properties for potential applications in Li-ion batteries, photocatalysis, chemical sensing, and solar cells. In contrast to previous studies performed with powder samples, which often suffer from impurities and lattice water, here we report Raman spectra from highly crystalline TiO 2 (B) films epitaxially grown on Si substrates with a thin SrTiO 3 buffer layer. The reduced background from the Si substrate significantly benefits acquisition of polarization-dependent Raman spectra collected from the high-quality thin films, which are compared to nanopowder results reported in the literature. The experimental spectra were compared with density functional theory calculations to analyze the atomic displacements associated with each Raman-active vibrational mode. These results provide a standard reference for further investigation of the crystallinity, structure, composition, and properties of TiO 2 (B) materials with Raman spectroscopy.
Strontium titanate (STO), with a wide spectrum of emergent properties such as ferroelectricity and superconductivity, has received significant attention in the community of strongly correlated materials. In the strain-free STO film grown on the SrRuO 3 buffer layer, the existing polar nanoregions can facilitate room-temperature ferroelectricity when the STO film thickness approaches 10 nm. Here we show that around this thickness scale, the freestanding STO films without the influence of a substrate show the tetragonal structure at room temperature, contrasting with the cubic structure seen in bulk form. Further, the spectroscopic measurements reveal the modified Ti-O orbital hybridization that causes the Ti ion to deviate from its nominal 4+ valency (3d o configuration) with excess delocalized 3d electrons. Additionally, the Ti ion in TiO 6 octahedron exhibits an off-center displacement. The inherent symmetry lowering in ultrathin freestanding films offers an alternative way to achieve tunable electronic structures that are of paramount importance for future technological applications.
Material defects remain as the main bottleneck to the progress of topological insulators (TIs). In particular, efforts to achieve thin TI samples with dominant surface transport have always led to increased defects and degraded mobilities, thus making it difficult to probe the quantum regime of the topological surface states. Here, by utilizing a novel buffer layer scheme composed of an In 2 Se 3 /(Bi 0.5 In 0.5 ) 2 Se 3 heterostructure, we introduce a quantum generation of Bi 2 Se 3 films with an order of magnitude enhanced mobilities than before. Furthermore, this scheme has led to the first observation of the quantum Hall effect in Bi 2 Se 3 .
Buffer layers, such as CdS and Mg x Zn 1-x O (MZO), are critical for CdTe and other thin film polycrystalline solar cells. A ternary compound, such as MZO, allows for interface engineering by adjusting composition, bandgap, and doping to manipulate barriers and recombination to enhance thin film efficiencies toward 25%. Here, theoretical studies demonstrate the enormous impact of front interface offset and emitter doping have on device performance. The results reveal it is possible to achieve 25% device efficiency with open-circuit voltage >1 V, even for 10 5 cm/s recombination velocity, provided the interface offsets and doping are properly engineered.
Utilizing pulsed laser deposition, a film of EuO 1–x was deposited onto a Si(001) substrate with MgO buffer and compared to the same heterostructure with an additional BaTi 2 O 5 thin film on top of the EuO 1–x surface. X-ray diffraction (XRD) indicates the films crystallize into a preferred EuO(111) orientation; it also reveals the clear presence of EuSi 2 , which suggests Si or Eu diffuses across the MgO buffer layer. EuO 1–x films exhibit a ferromagnetic (FM) signature and temperature-dependent exchange bias, indicated by MOKE measurements, suggesting the presence of a magnetic order well above the EuO Curie temperature with possible origins in charge carrier density near the interface. In comparison, an antiferromagnetic character persists well above the EuO Curie temperature of 69 K and the enhanced Curie temperature of 150 K for BaTi 2 O 5 films grown on the EuO 1–x films. Furthermore, the antiferromagnetic behavior is not seen in thicker EuO 1–x thin films when integrated with other ferroelectric (FE) phases of the BaO–TiO 2 system, suggesting an origin in the perturbed charge population at the BaTi 2 O 5 /EuO 1–x interface.
Delafossites, composed of noble metal (A + ) and strongly correlated sublayers (BO 2 – ), form natural superlattices with highly anisotropic properties. These properties hold significant promise for various applications, but their exploitation hinges on the successful growth of high-quality thin films on suitable substrates. Unfortunately, the unique lattice geometry of delafossites presents a significant challenge to thin-film fabrication. Different delafossites grow differently, even when deposited on the same substrate, ranging from successful epitaxy to complete growth suppression. These variations often lack a clear correlation to obvious causes like lattice mismatch. Unidentified stabilization mechanisms appear to enable growth in certain cases, allowing these materials to form stable thin films or act as buffer layers for subsequent delafossite growth. This study employs advanced scanning transmission electron microscopy techniques to investigate the nucleation mechanism underlying the stable growth of PdCoO 2 films on Al 2 O 3 and LaAlO 3 substrates grown via molecular-beam epitaxy. Our findings reveal the presence of a secondary phase within the substrate surface that stabilizes the films. This mechanism deviates from the conventional understanding of strain relief mechanisms at oxide heterostructure interfaces and differs significantly from those observed for Cu-based delafossites.
Here, we investigate the effect of high work function contacts in halide perovskite absorber-based photovoltaic devices. Photoemission spectroscopy measurements reveal that band bending is induced in the absorber by the deposition of the high work function molybdenum trioxide (MoO 3 ). We find that direct contact between MoO 3 and the perovskite leads to a chemical reaction, which diminishes device functionality. Introducing an ultrathin spiro-MeOTAD buffer layer prevents the reaction, yet the altered evolution of the energy levels in the methylammonium lead iodide (MAPbI 3 ) layer at the interface still negatively impacts device performance.
In organic electronic devices, indium tin oxide (ITO) and poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) are the most common transparent electrode and anodic buffer layer materials, respectively. A widespread concern is that PEDOT:PSS is acidic and etches ITO. We show that this issue is not serious: only a few nanometers of ITO are etched in typical device processing conditions and storage thereafter; conductivity losses are affordable; and optical transmission gains further offset these losses. Organic photovoltaic (OPV) devices fabricated on old ITO (with PEDOT:PSS history) were similar or higher in efficiency than devices on fresh ITO. Poly[[4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b']dithiophene-2,6-diyl][3-fluoro-2-[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl]] (PTB7) devices on old ITO showed efficiencies up to 9.24% compared to 8.72% efficient devices on fresh ITO. This reusability of ITO can be impactful for economics of organic electronics because ITO accounts for almost 90% of energy embedded in devices, such as OPVs.
Room temperature sodium-ion batteries are of great interest for high-energy-density energy storage systems because of low-cost, natural abundance of sodium. Here, we report a novel graphene nanosheets-wrapped phosphorus composite as an anode for high performance sodium-ion batteries though a facile ball-milling of red phosphorus and graphene nanosheets. Not only can the graphene nanosheets significantly improve the electrical conductivity, but they also serve as a buffer layer to accommodate the large volume change of phosphorus in the charge-discharge process. As a result, the graphene wrapped phosphorus composite anode delivers a high reversible capacity of 2077 mAh/g with excellent cycling stability (1700 mAh/g after 60 cycles) and high Coulombic efficiency (>98%). This simple synthesis approach and unique nanostructure can potentially extend to other electrode materials with unstable solid electrolyte interphases in sodium-ion batteries.
Abstract The availability of native substrates is a cornerstone in the development of microelectronic technologies relying on epitaxial films. If native substrates are not available, virtual substrates - crystalline buffer layers epitaxially grown on a structurally dissimilar substrate - offer a solution. Realizing commercially viable virtual substrates requires the growth of high-quality films at high growth rates for large-scale production. We report the stoichiometric growth of SrTiO 3 exceeding 600 nm hr −1 . This tenfold increase in growth rate compared to SrTiO 3 grown on silicon by conventional methods is enabled by a self-regulated growth window accessible in hybrid molecular beam epitaxy. Overcoming the materials integration challenge for complex oxides on silicon using virtual substrates opens a path to develop new electronic devices in the More than Moore era and silicon integrated quantum computation hardware.
Abstract Organic photovoltaic cells (OPVs) have the potential of becoming a productive renewable energy technology if the requirements of low cost, high efficiency and prolonged lifetime are simultaneously fulfilled. So far, the remaining unfulfilled promise of this technology is its inadequate operational lifetime. Here, we demonstrate that the instability of NFA solar cells arises primarily from chemical changes at organic/inorganic interfaces bounding the bulk heterojunction active region. Encapsulated devices stabilized by additional protective buffer layers as well as the integration of a simple solution processed ultraviolet filtering layer, maintain 94% of their initial efficiency under simulated, 1 sun intensity, AM1.5 G irradiation for 1900 hours at 55 °C. Accelerated aging is also induced by exposure of light illumination intensities up to 27 suns, and operation temperatures as high as 65 °C. An extrapolated intrinsic lifetime of > 5.6 × 10 4 h is obtained, which is equivalent to 30 years outdoor exposure.
Abstract Oxide ceramic electrolytes (OCEs) have great potential for solid-state lithium metal (Li 0 ) battery applications because, in theory, their high elastic modulus provides better resistance to Li 0 dendrite growth. However, in practice, OCEs can hardly survive critical current densities higher than 1 mA/cm 2 . Key issues that contribute to the breakdown of OCEs include Li 0 penetration promoted by grain boundaries (GBs), uncontrolled side reactions at electrode-OCE interfaces, and, equally importantly, defects evolution (e.g., void growth and crack propagation) that leads to local current concentration and mechanical failure inside and on OCEs. Here, taking advantage of a dynamically crosslinked aprotic polymer with non-covalent –CH 3 ⋯CF 3 bonds, we developed a plastic ceramic electrolyte (PCE) by hybridizing the polymer framework with ionically conductive ceramics. Using in-situ synchrotron X-ray technique and Cryogenic transmission electron microscopy (Cryo-TEM), we uncover that the PCE exhibits self-healing/repairing capability through a two-step dynamic defects removal mechanism. This significantly suppresses the generation of hotspots for Li 0 penetration and chemomechanical degradations, resulting in durability beyond 2000 hours in Li 0 -Li 0 cells at 1 mA/cm 2 . Furthermore, by introducing a polyacrylate buffer layer between PCE and Li 0 -anode, long cycle life >3600 cycles was achieved when paired with a 4.2 V zero-strain cathode, all under near-zero stack pressure.
Here by inserting an epitaxial in-plane buffer layer of Bi 5 FeTi 3 O 15 , an artificial flux closure architecture enables ferroelectric polarization from a single unit cell of BaTiO 3 or BiFeO 3 .
Abstract Control over the concurrent occurrence of structural (monoclinic to tetragonal) and electrical (insulator to the conductor) transitions presents a formidable challenge for VO 2 -based thin film devices. Speed, lifetime, and reliability of these devices can be significantly improved by utilizing solely electrical transition while eliminating structural transition. We design a novel strain-stabilized isostructural VO 2 epitaxial thin-film system where the electrical transition occurs without any observable structural transition. The thin-film heterostructures with a completely relaxed NiO buffer layer have been synthesized allowing complete control over strains in VO 2 films. The strain trapping in VO 2 thin films occurs below a critical thickness by arresting the formation of misfit dislocations. We discover the structural pinning of the monoclinic phase in (10 ± 1 nm) epitaxial VO 2 films due to bandgap changes throughout the whole temperature regime as the insulator-to-metal transition occurs. Using density functional theory, we calculate that the strain in monoclinic structure reduces the difference between long and short V-V bond-lengths (Δ V − V ) in monoclinic structures which leads to a systematic decrease in the electronic bandgap of VO 2 . This decrease in bandgap is additionally attributed to ferromagnetic ordering in the monoclinic phase to facilitate a Mott insulator without going through the structural transition.