Search NASA⌕ Search

SEARCH · Search NASA

Results for “cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Engineering-Scale Development/Demonstration of Zirconium Recovery from Used Duel Cladding

Recognizing that the zirconium (Zr) in used nuclear fuel (UNF) cladding is the second largest mass in UNF assemblies, process development studies for the recovery and purification of Zr were initiated and have been in progress at Oak Ridge National Laboratory (ORNL) for the last several years as a major element of waste minimization for advanced nuclear fuel recycle. Together with uranium recovery and recycle, Zr recovery would divert >90% (wt.) of the UNF assemblies from emplacement in a geologic repository by converting the Zr to low-level waste or reuse/recycle.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Milestone 1.2.16. Reconciling the Impacts of Thermal Pretreatment on Radiation-Induced H2 Generation from Aluminum-Clad Spent Nuclear Fuel Surrogate Materials

To support the technical basis for the extended dry storage of aluminum-clad spent nuclear fuel (ASNF), thermal pretreatment procedures to minimize the radiation-induced generation of molecular hydrogen (H2) have been investigated. The aim of thermal pretreatment is to eliminate the residual adsorbed water content on the ASNF’s corrosion layers, precursors for H2 generation. To date, irradiation studies in this area have found conflicting results for the effectiveness of thermal pretreatment procedures. The aim of this study was to reconcile those differences. However, the presented results, which utilized a modified in situ thermal pretreatment procedure, afforded H2 yield data that further indicates that thermal pretreatment does not significantly reduce the radiation-induced yield of H2 from gamma irradiated ASNF surrogate materials. Assessment of the differences between thermal pretreatment studies suggests that stainless-steel—present in the irradiation setup of studies that demonstrated a reduction in the yield of H2 with thermal pretreatment—may afford not only unanticipated interfacial chemistry, but also the formation and radiolytic contribution of iron oxides to the chemistry underpinning the formation of H2 in these systems. Given the Department of Energy Standard Canister—proposed for the extended dry storage of ASNF—is predominantly composed of stainless-steel, the potential contribution of stainless-steel and its corrosion layers to radiolytic H2 production should be further investigated. This research was funded by the U.S. Department of Environmental Management, Office of Technology Development, under contract DE-AC07-05ID14517.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Impacts of Ionizing Radiation on Sulfur Chloride Compounds for Advanced Fuel Cladding Decontamination Processes

Tripling the nation’s nuclear energy capacity is a critical component for significantly increasing energy production and reducing energy costs for American families and businesses. Achieving this vision requires fuel cycle technologies that maximize resource utilization while minimizing radioactive waste generation. Advanced sulfur chloride–based chlorination technologies are being developed to enable efficient recycling of fuel cladding materials, which account for a significant fraction of used nuclear fuel. However, the impacts of ionizing radiation on the longevity and performance of these sulfur chloride compounds are not well established. Here, we will explore the effects of gamma and electron-beam irradiation on the chemical composition of select sulfur chloride reagents, specifically sulfur monochloride (S2Cl2) and thionyl chloride (SOCl2), and the impacts of pre-irradiation on the chlorination yield/chemical dissolution of surrogate aluminum alloy 6061 (AA6061-T6) materials.

38 - RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCL↗

Resonant Mode Engineering of Photonic Crystal Sensors Clad with Ultralow Refractive Index Porous Silicon Dioxide

Porous SiO 2 (PSiO 2 ) with ultralow refractive index ($n$ = 1.09) is incorporated as the cladding of a photonic crystal (PC) refractive index sensor with enhanced sensitivity through the establishment of resonant modes that principally reside in the liquid medium covering the PC surface. PSiO 2 , obtained by thermal oxidation of porous Si that has been transferred to a transparent substrate, is transparent at visible and near infrared wavelengths with a refractive index determined by its porosity. The PSiO 2 periodic grating structure ($Λ$ = 590 nm) is patterned by nanoimprint lithography and reactive ion etching, then conformally coated by sputtering high refractive index TiO 2 to seal the pores from liquid infiltration. With the refractive index of PSiO 2 much lower than that of water, the resonant mode “flips” its spatial distribution from within the solid dielectric regions of the photonic crystal to reside mainly in the water media covering the PC, resulting in 4× greater resonant wavelength shift for a fixed refractive index change. This study demonstrates design, fabrication, and testing of the sensor as a refractometer, supported by electromagnetic simulations of the resonant mode spatial distribution, in which porous PC sensors are compared to nonporous PC sensors.

14 SOLAR ENERGY↗

Accident tolerant FeCrAl fuel cladding: current status towards commercialization

FeCrAl alloys are rapidly becoming a mature concept for accident tolerant fuel applications. The FeCrAl material class has shown excellent oxidation resistance in high-temperature steam environments, a key aspect of any accident tolerant cladding concept, while also being corrosion resistant, stress corrosion cracking (SCC) resistant, irradiation-induced swelling resistant, weldable, and formable. Current research efforts are focused on design, development and commercial scaling of advanced FeCrAl alloys including large-scale thin-walled seamless tube production followed by a broad spectrum of degradation evaluations in both normal and off-normal conditions. Included in this discussion will be theoretical analysis of the alloying principles and rules, alloy composition design, and overview of the most recent empirical database on possible degradation phenomena for FeCrAl alloys. The results are derived from extensive in-pile and out-of-pile experiments and form the basis for near-term deployment of a lead-test rod and/or assembly within a commercially operating nuclear power plant.

Field, Kevin G.↗

Characterization of the Hydrothermal Corrosion Behavior of Ceramics for Accident Tolerant Fuel Cladding

Accident-tolerant fuel (ATF) is an increasingly important research topic for the nuclear industry, and ceramics such as SiC are strong contenders for deployment as ATF cladding. The hydrothermal corrosion characteristics of SiC and Al2O3 were investigated via constantly-refreshing autoclave corrosion and post exposure characterization. Four different types of chemical vapor deposited (CVD) SiC specimens were examined (two with high electrical resistance, one with low electrical resistance, and a single crystal 4H structural variant). Al2O3 specimens were prepared in single crystal and polycrystalline states. PWR primary water, BWR–HWC, and BWR–NWC environments were maintained throughout the experiments. Characterization conducted using SEM and EDS was used to determine factors affecting corrosion rates and susceptibility to grain boundary attack in each water chemistry condition. Raman spectroscopy was also used to determine chemical variation of the surface with corrosion. Grain boundary attack was found to be significant for both alumina and SiC polycrystalline variants.

Doyle, Peter↗

Surface coupling of plasma optical emission spectra with bent metal-clad waveguide

We present the design of compact bent metal-clad waveguides to collect the vertically emitted light and to transmit to the horizontal direction. The intention of the design is to collect the plasma optical emission spectra inside the semiconductor etch process chamber to monitor plasma gas phase chemistry resides in the process chamber. Coupler A has been designed for visible spectra range from 748 to 753 nm at which the maximum coupling efficiency is over 52%, while Coupler B operates at the wavelength range from 775 to 780 nm with coupling strength of 62% and Coupler C covers the visible spectrum from 808 to 813 nm with its maximum efficiency of 60%. The surface couplers reveal good spectral characteristics, considerable alignment tolerance and minimal size of 9 × 5 × 1.6 µm{sup 3} each. Relatively simple geometrical structure over conventional grating coupler is advantageous to lower the fabrication cost as well.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Sagging Mechanisms of Three-Layer Aluminum Clad Foils used in the Heat Exchanger in the Brazing Process

The sagging mechanisms of a three-layer aluminum clad foils (AA4343/AA3003Mod/AA4343) with final rolling reduction of 20-50% during brazing were studied. The results show that the sagging behavior of the aluminum brazed foils during the brazing cycle can be divided into four stages: Stage I is the slight sagging stage, during which sagging deformation can almost be ignored; Stage II is referred to as the accelerative sagging stage, and the sagging behavior is mainly ascribed to recovery. In stage II, the greater the reduction ratio is, the earlier the recovery ends, and the smaller the value of the sagging distance is. Stage III is the slow sagging stage, and sliding deformation along the grain boundaries is responsible for the slow sagging rate. Stage IV is the erosion stage. During stage IV, the coarsely recrystallized grains can inhibit erosion and are helpful in obtaining excellent sagging resistance, while the foils with finely recrystallized grains or non-recrystallized structure show severe erosion and limited sagging resistance.

36 MATERIALS SCIENCE↗

Effect of neutron and ion irradiation on the metal matrix and oxide corrosion layer on Zr-1.0Nb cladding alloys

A detailed study has been carried out on recrystallised Zr-1.0Nb alloys corroded and irradiated under different conditions, including ex-autoclave and ex-reactor samples. After 540 days in reactor and damage around 5 dpa, the neutron irradiated sample shows no serious evidence for radiation enhanced corrosion and is still in pre-transition stage. The good corrosion resistance of the neutron irradiated Zr-1.0Nb can be related to the higher volume fraction of tetragonal phase and fewer interconnected nano porosity/cracks in the oxide. This indicates less tetragonal to monoclinic transition, leads to more protective oxide in the neutron irradiated sample, containing little evidence for short circuit paths for the penetration of oxygen or water towards the metal-oxide interface. These observations on a sample with a slow overall oxidation rate are consistent with the hypothesis that interconnected porosity can lead to early transitions and rapid oxidation. Tetragonal oxide can be either stabilised by irradiation, or stabilised by local release of impurity species from SPPs such as dissolution of Fe from Zr-Nb-Fe precipitates or radiation introduced precipitates (RIPs) which is likely to be small β-Nb clusters. The oxide consists of well-aligned columnar-equiaxed microstructure in the autoclave sample while a more complex oxide grain structure was observed in the neutron-irradiated sample. As oxide continues to grow, there are more < a > and < c > loops, dissolved Fe and RIPs in the metal matrix, however, the corrosion rate is low enough for the tetragonal oxide to stabilise and suboxide + Zr(Osat) phases exist for protectiveness, so there is no enhanced corrosion after radiation. In situ ion irradiation in the TEM revealed no visible defect clusters or voids in the oxide, suggesting that radiation damage to the metal matrix rather than oxide may have a stronger effect on corrosion mechanisms after neutron irradiation, however, cascade damages are not visible in this case. Neutron irradiation also seems to have little effect on promoting fast oxidation or dissolution of β-Nb precipitates into the surrounding oxide or metal during irradiation. Furthermore, these results are discussed in the light of the current mechanisms for corrosion of nuclear fuel cladding alloys.

(S)TEM↗

Effect of PVD-coated chromium on the subcooled flow boiling performance of nuclear reactor cladding materials

Here we elucidate the separate effect of a thin Cr coating deposited by physical vapor deposition (PVD) on the subcooled flow boiling performance of zircaloy-4. First, we run flow boiling experiments on prototypical zircaloy-4 surfaces mimicking the scratch pattern and surface roughness of nuclear reactor claddings. Then, we PVD-coat a 0.3 µm thick chromium layer on the same exact surface and repeat the same flow boiling investigations. All experiments are run using deionized water at atmospheric pressure, flowing on a 1 × 3 cm 2 rectangular cross section channel at a rate of 1000 kg/m 2 /s and a subcooling of 10 K. We measure the average temperature of the boiling surface at increasing surface heat fluxes, covering a wide range of heat transfer regimes, from single-phase forced convection to the boiling crisis. We also record high-speed videos of the boiling process, which we postprocess to measure bubble nucleation site density, growth time, departure diameter and frequency. The surface analysis reveals that, while the chromium coating does not seem change the surface roughness and morphology, it improves surface wettability. However, it decreases the critical heat flux. The chromium coating causes an increase of nucleation temperature, bubble departure diameter and growth time, and a reduction of the nucleation site density. The concurrence of these observations indicates that a size reduction of the nucleation sites, conformally covered by the chromium coating, may be the cause of the boiling performance deterioration. We confirm this hypothesis repeating the same analysis on a FeCrAl sample prepared and tested using the same protocol as the zircaloy-4 sample, but with a different initial surface texture.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Charge Optimized Many Body (COMB) potentials for simulation of nuclear fuel and clad

The Charge Optimized Many Body (COMB) potential formalism enables the molecular dynamics simulation of complex materials structures in which multiple types of bonding (metallic, covalent, ionic and secondary bonding) coexist. Here we briefly review the COMB formalism and illustrate its capabilities to address critical issues in the area of nuclear fuel. In particular, we In Section 3, we look at U, UO2 and the process of oxidation of U. In Section 4, we look at the mechaincal behavior of Zr, representing LWR clad, and explore the effects of oxidation and hydridation on the mechanical response. In Section 5, we describe the capabilities of COMB simulations of corrosion. Since there has been relatveily little work done in this area, we also describe some work performed on non-nuclear materials, which illustrate the capabilities. Section 6 briefly describes some of the known limitations of the COMB approach.

36 MATERIALS SCIENCE↗

Comparison of steady and transient flow boiling critical heat flux for FeCrAl accident tolerant fuel cladding alloy, Zircaloy, and Inconel

Steady and transient (with a heating rate of 685?/s) internal-flow CHF (Critical Heat Flux) experiments were conducted under atmospheric pressure at a fixed inlet temperature (40? or 60?) and mass flow (300kg/m 2 s) on Fe-13Cr-6Al alloy, Inconel 600 and Zircaloy-4 tube samples. Multiple experiments were repeated on the same specimen to investigate the effect of surface characteristic changes (i.e., roughness, wettability, and oxide scale morphology) on the occurrence of CHF. Despite notable changes of wettability, roughness, and oxide layer characteristics on samples that had already been subjected to CHF, measured flow CHF remained unchanged throughout repeated experiments for tested materials. This demonstrates that the surface effects on flow CHF are limited in the test conditions. In the steady-state flow boiling condition, Fe-13Cr-6Al alloy demonstrated a 22% and 14% increase in CHF compared to Zircaloy-4 and Inconel 600, respectively. Compared to the 2006 Groeneveld CHF lookup table, Fe-13Cr-6Al alloy gives a 13% increase in the tested flow boiling condition. Material properties are considered primarily responsible for the observed CHF differences among the tested materials. The surface thermal economy parameter $\frac{(pc_p)^{3/2}}{\sqrt{k}}$ is proposed as an explanation for the observed CHF differences; this parameter is related to material’s ability to avoid an irreversible dry spot formation. The apparent disagreement of Zircaloy-4 CHF with both the look up table predictions and Inconel 600 shows the limitation of departure of nuclate boiling (DNB) evaluations that do not consider cladding materials. The transient Fe-13Cr-6Al CHF is 39% and 23% higher than the lookup table prediction and the steady-state condition experimental result, respectively.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High temperature oxidation behavior of Zr-1Nb cladding alloy E110.

Oxidation experiments were conducted at 1000-1200 C in flowing steam with samples of as-received Zr-1Nb alloy E110 tubing and/or polished E110 tubing. The purpose was to determine the oxidation behavior of this alloy under postulated loss-of-coolant accident conditions in light water reactors. The as-received E110 tubing exhibited a high degree of susceptibility to nodular oxidation and breakaway oxidation at relatively low test times, as compared to other cladding alloys. The nodules grew much more rapidly at 1000 C than 1100 C, as did the associated hydrogen uptake. The oxidation behavior was strongly affected by the surface condition of the materials. Polishing to {approx}0.1 {micro}m roughness (the roughness of the as-received tubing was {approx}0.4 {micro}m) delayed breakaway oxidation. Polishing also removed surface impurities. For polished samples oxidized at 1100 C, no significant nodular oxidation appeared up to 1000 s. For polished samples oxidized at 1000 C, hydrogen uptake >100 wppm was delayed from {approx}300 s to >900 s. Weight-gain coefficients were determined for pre-breakaway oxidation of polished-only and machined-and-polished E110 tubing samples: 0.162 (mg/cm{sup 2})/s{sup 0.5} at 1000 C and 0.613 (mg/cm{sup 2})/s{sup 0.5} at 1100 C.

08 HYDROGEN↗

Development and property evaluation of nuclear grade wrought FeCrAl fuel cladding for light water reactors

Development of nuclear grade, iron-based wrought FeCrAl alloys has been initiated for light water reactor (LWR) fuel cladding to serve as a substitute for zirconium-based alloys with enhanced accident tolerance. Ferritic alloys with sufficient chromium and aluminum additions can exhibit significantly improved oxidation kinetics in high-temperature steam environments when compared to zirconium-based alloys. In the first phase, a set of model FeCrAl alloys containing 10–20Cr, 3–5Al, and 0–0.12Y in weight percent, were prepared by conventional arc-melting and hot-working processes to explore the effect of composition on the properties of FeCrAlY alloys. It was found that the tensile properties were insensitive to the alloy compositions studied; however, the steam oxidation resistance strongly depended on both the chromium and the aluminum contents. The second phase development focused on strengthening Fe-13Cr-5Al with minor alloying additions of molybdenum, niobium, and silicon. Combined with an optimized thermo-mechanical treatment, a thermally stable microstructure was produced with improved tensile properties at temperatures up to 741°C.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Development of low-Cr ODS FeCrAl alloys for accident-tolerant fuel cladding

Low-Cr oxide dispersion strengthened (ODS) FeCrAl alloys were developed as accident tolerant fuel cladding because of their excellent oxidation resistance at very high temperature, high strength and improved radiation tolerance. Fe-12Cr-5Al wt.% gas atomized powder was ball milled with Y 2 O 3 +FeO, Y 2 O 3 +ZrO 2 or Y 2 O 3 +TiO 2 , and the resulting powders were extruded at 950°C. The resulting fine grain structure, particularly for the Ti and Zr containing alloys, led to very high strength but limited ductility. Comparison with variants of commercial PM2000 (Fe-20Cr-5Al) highlighted the significant impact of the powder consolidation step on the alloy grain size and, therefore, on the alloy mechanical properties at T < 500 °C. These low-Cr compositions exhibited good oxidation resistance at 1400 °C in air and steam for 4 h but could not form a protective alumina scale at 1450 °C, similar to observations for fine grained PM2000 alloys. As a result, the effect of alloy grain size, Zr and Ti additions, and impurities on the alloy mechanical and oxidation behaviors are discussed.

36 MATERIALS SCIENCE↗

High-temperature oxidation and quenching of chromium-coated zirconium alloy ATF cladding tubes with and w/o pre-damage

Chromium-coated zirconium alloys are one of the promising candidates for accident-tolerant fuel cladding (ATF) tubes for light water reactors (LWRs). In this study, the high temperature oxidation and degradation of two types of Cr coatings (cold spray and physical vapor deposition) with and without pre-damage by scratches were investigated on prototype rod segment samples filled with ZrO 2 pellets and tightly sealed with welded end caps. Isothermal tests at 1100 and 1200 °C were terminated by quenching with water; transient tests were performed up to 1500–1600 °C until complete coating failure. The positive effect of both types of Cr coatings was observed in all tests. Pre-damaged specimens showed only locally increased oxidation of the scratched zone, but no negative effects on the adjacent Cr coating. Finally, the behavior of the two types of coatings is compared and the degradation mechanisms are discussed based on hydrogen release data, extensive metallographic post-test examinations, and the current state of global research.

36 MATERIALS SCIENCE↗

Burst characteristics of advanced accident-tolerant FeCrAl cladding under temperature transient testing

Here assessment of burst characteristics of accident-tolerant fuel (ATF) claddings is essential to evaluate the safety margins of nuclear reactors, and better understanding can enable accelerated licensing for reactor concepts that include the new materials. Therefore, this study investigated the burst behavior of an ATF candidate of C26M, which is an iron–chromium–aluminum alloy (FeCrAl) under transient testing like the simulated loss-of-coolant accident (LOCA) conditions, except the water-quenching phase, in light-water reactors (LWRs). The effect of LOCA specimen length was assessed in terms of post-burst tube parameters. No critical length effect was determined on the burst pressure, burst location, and burst size measurements. Burst temperature showed larger variation likely due to its measurement approach used in this study. The post-test diametral strain was identified as the critical parameter to reduce the specimen length as compared to tube burst length or width. Postmortem optical metrology and digital image correlation were employed to determine the local strain-state during the simulated LOCA, which showed the loading path was close to equibiaxial conditions in regions away from the burst location, rather than internally pressurized conditions (or “plane-strain” tension). Pst-test microstructural characterizations of the FeCrAl revealed that ductile damage was present at the edge of the outer radial surface while the rest of the material was ruptured via cleavage at LOCA burst temperatures. Furthermore, internal grain boundary cracks were observed at locations away from the tube burst region. This behavior was considered to occur during the cooling down period of the simulated LOCA test. Overall, this study aimed to provide essential data for fuel performance code development by considering micromechanics of the deformation and failure.

36 MATERIALS SCIENCE↗