Search NASA⌕ Search

SEARCH · Search NASA

Results for “diffractive networks”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Ultranarrow linewidth, magnetically switched, long pulse, xenon chloride laser

A spectral linewidth of less than 70 fm and diffraction-limited beam divergence have been obtained from a long-pulse, electric-discharge xenon chloride laser with intracavity Fabry-Perot etalons. A gain duration of 100 ns provided for multipass operation of the etalons, significantly improving both contrast and finesse. The electrical-discharge circuit required to produce this long gain duration was comprised of a pulse-forming network, a saturable-inductor magnetic switch, and a tapered constant-impedance interface transmission line.

Pacala, T. J.↗

Sensing Water Vapon via Spacecraft Radio Occultation Observations

The radio occultation technique has been used to characterize planetary atmospheres since the 1960's spanning atmospheric pressures from 16 microbars to several bars. In 1988, the use of GPS signals to make occultation observations of Earth's atmosphere was realized by Tom Yunck and Gunnar Lindal at JPL. In the GPS to low-Earth-orbiter limb- viewing occultation geometry, Fresnel diffraction yield a unique combination of high vertical resolution of 100 m to 1 km at long wavelengths (approx. 20 cm) insensitive to particulate scattering which allows routine limb sounding from the lower mesosphere through the troposphere. A single orbiting GPS/GLONASS receiver can observe - 1000 to 1400 daily occultations providing as many daily, high vertical resolution soundings as the present global radiosonde network, but with far more evenly distributed, global coverage. The occultations yield profiles of refractivity as a function of height. In the cold, dry conditions of the upper troposphere and above (T less than 240 K), profiles of density, pressure (geopotential), and temperature can be derived. Given additional temperature information, water vapor can be derived in the midddle and lower troposphere with a unique combination of vertical resolution, global distribution and insensitivity to clouds and precipitation to an accuracy of approx. 0.2 g/kg. At low latitudes, moisture profiles will be accurate to 1-5% within the convective boundary layer and better than 20% below 6 to 7 km. Accuracies of climatological averages should be approx. 0. 1 g/kg limited by the biases in the temperature estimates. To use refractivity to constrain water vapor, knowledge of temperature is required. The simplest approach is to use the temperature field from an analysis such as the 6 hour ECMWF global analysis interpolated to the locations of each occultation. A better approach is to combine the temperature and moisture fields from such an analysis with the occultation refractivity in a weighting scheme based on the errors in each data field. A ID variational combinational approach has been developed at the UKMO. We win present results from both approaches from GPS/MET data taken in June and July 1995 and compare them with the ECMWF global 6 hour moisture analyses which are derived largely from TOVS and radiosonde data. Overall, the atmosphere below the 500 mb level appears somewhat drier in general than the ECNIWF humidity field. A 2-D (latitude vs. height) climatological snapshot derived from a 2-week span of GPS/MET data will be compared to the humidity climatology of Peixoto and Oort derived from radiosonde data from 1963-1973. Differences between the GPS results and Peixoto and Oort may be the signature of a climate trend over the past 30 years.

Kursinski, E. Robert↗

Study on Nanocellulose Properties Processed Using Different Methods and Their Aerogels

In this paper the effects of different mechanical methods including homogenization, ultrasonication and grinding on the properties of the nanocellulose materials and their aerogels, were investigated. The cellulose nanocrystal products, (CNC-H) and (CNC-U), were prepared by homogenization and ultrasonication of the acid hydrolyzed pulps, respectively. The aerogel products were produced by solvent exchanging of nanocellulose hydrogels with tertiary butyl alcohol and followed by freeze drying. The nanocellulose materials were studied using transmission electron microscopy, field emission scanning electron microscopy (FE-SEM), Fourier transformed infrared spectroscopy (TEM), X-ray diffraction (XRD), thermal gravimetric analysis (TGA). Size distribution and surface charges of the nanocellulose suspensions were measured by zetasizer. Also, the morphology, the porosity properties and surface area of the CNCs and CNF aerogels were investigated via FE-SEM and nitrogen adsorption–desorption isotherms. The results showed that CNC-H has higher surface charge, suspension stability (− 41.8 mV), crystallinity index (74.7%) and better size dispersion than CNC-U and CNF with an average particle size of 122 nm. CNC-H microstructures demonstrated homogeneous network structure with smaller nanometer dimensions (15–30 nm width and 60–400 nm length). However, the CNC-H showed lower thermal stability compared to CNC-U and CNF. Larger average pore size (16.32 nm), pore volume (0.42 cc/g) and high specific surface area (> 100 m{sup 2} g{sup −1}) in CNC-H aerogel were obtained. Graphical Abstract: Suspensions of nanocellulose (NC) were prepared by different mechanical methods: Homogenizing, Ultrasonic and grinding. The NC products were investigated and their differences in morphology and other characteristics were studied. The aerogels were prepared from the nanocellulose hydrogels. The nitrogen physisorption was used to study the pore characteristics of the aerogels. .

36 MATERIALS SCIENCE↗

Synthesis, crystal and electronic structure, and physical properties of the new lanthanum copper telluride La{sub 3}Cu{sub 5}Te{sub 7}

The new lanthanum copper telluride La{sub 3}Cu{sub 5-x}Te{sub 7} has been obtained by annealing the elements at 1073 K. Single-crystal X-ray diffraction studies revealed that the title compound crystallizes in a new structure type, space group Pnma (no. 62) with lattice dimensions of a=8.2326(3) A, b=25.9466(9) A, c=7.3402(3) A, V=1567.9(1) A{sup 3}, Z=4 for La{sub 3}Cu{sub 4.86(4)}Te{sub 7}. The structure of La{sub 3}Cu{sub 5-x}Te{sub 7} is remarkably complex. The Cu and Te atoms build up a three-dimensional covalent network. The coordination polyhedra include trigonal LaTe{sub 6} prisms, capped trigonal LaTe{sub 7} prisms, CuTe{sub 4} tetrahedra, and CuTe{sub 3} pyramids. All Cu sites exhibit deficiencies of various extents. Electrical property measurements on a sintered pellet of La{sub 3}Cu{sub 4.86}Te{sub 7} indicate that it is a p-type semiconductor in accordance with the electronic structure calculations. -- Graphical abstract: Oligomeric unit comprising interconnected CuTe{sub 3} pyramids and CuTe{sub 4} tetrahedra. Display Omitted Research highlights: {yields} La{sub 3}Cu{sub 5-x}Te{sub 7} adopts a new structure type. {yields} All Cu sites exhibit deficiencies of various extents. {yields} The coordination polyhedra include trigonal LaTe{sub 6} prisms, capped trigonal LaTe{sub 7} prisms, CuTe{sub 4} tetrahedra and CuTe{sub 3} pyramids. {yields} La{sub 3}Cu{sub 5-x}Te{sub 7} is a p-type semiconductor.

36 MATERIALS SCIENCE↗

Effect of Li{sub 2}O on the Behavior of Melting, Crystallization, and Structure for CaO-Al{sub 2}O{sub 3}-Based Mold Fluxes

The effect of Li{sub 2}O content on the behavior of melting, crystallization, and molten structure for CaO-Al{sub 2}O{sub 3}-based mold fluxes was investigated in this article, through use of single hot thermocouple technology (SHTT), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, and X-ray diffraction (XRD). The SHTT results showed that the melting temperature range of the designed mold fluxes decreases and the crystallization of mold fluxes is inhibited first and then becomes enhanced when the Li{sub 2}O content increases from 1 to 6 mass pct. The FTIR and Raman spectroscopy results suggested that Li{sub 2}O could release O{sup 2−} ions to break the complex Al-O-Al structural unit into Al-O{sup −} structure. Meanwhile, Li{sub 2}O could also stabilize the structural unit of Si-O-Al by link aluminate and Q{sub 0}{sup Si} structure through providing Li{sup +} ions to merge into the network and compensate for the charges between Al{sup 3+} and Si{sup 4+}. Besides, the XRD results indicated that the precipitation of LiAlO{sub 2} in molten slag would enhance the crystallization behavior of mold flux when Li{sub 2}O content is over 4.5 mass pct.

36 MATERIALS SCIENCE↗

Crystal structure and properties of tetragonal EuAg{sub 4}In{sub 8} grown by metal flux technique

The compound EuAg{sub 4}In{sub 8} has been obtained as single crystals in high yield from reactions run in liquid indium. X-ray diffraction on single crystals suggests that EuAg{sub 4}In{sub 8} crystallizes in the CeMn{sub 4}Al{sub 8} structure type, tetragonal space group I4/mmm with lattice constants a=b=9.7937(2) Å and c=5.7492(2) Å. Crystal structure of EuAg{sub 4}In{sub 8} is composed of pseudo Frank–Kasper cages occupied by one europium atom in each ring, which are shared through the corner along the ab plane resulting in a three dimensional network. The magnetic susceptibility of EuAg{sub 4}In{sub 8} was measured in the temperature range 2–300 K, which obeyed Curie–Weiss law above 50 K. Magnetic moment value calculated from the fitting indicates the presence of divalent europium, which was confirmed by X-ray absorption near edge spectroscopy. Electrical resistivity measurements suggest that EuAg{sub 4}In{sub 8} is metallic in nature with a probable Fermi liquid behavior at low temperature. - Graphical abstract: The tetragonal EuAg{sub 4}In{sub 8} has been grown as single crystals from reactions run in liquid indium. Magnetic and XANES measurements suggest divalent nature of Eu and resistivity measurements suggest metallic nature. - Highlights: • EuAg{sub 4}In{sub 8} phase having tetragonal phase is grown by metal flux technique. • Magnetic and XANES measurements exhibit divalent nature of Eu in EuAg{sub 4}In{sub 8}. • Resistivity measurement suggests metallic nature and probable Fermi liquid behavior.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

MAS-NMR investigations of the crystallization behaviour of lithium aluminum silicate (LAS) glasses containing P{sub 2}O{sub 5} and TiO{sub 2} nucleants

Lithium aluminum silicate (LAS) glass of composition (mol%) 20.4Li{sub 2}O-4.0Al{sub 2}O{sub 3}-68.6SiO{sub 2}-3.0K{sub 2}O-2.6B{sub 2}O{sub 3}-0.5P{sub 2}O{sub 5}-0.9TiO{sub 2} was prepared by melt quenching. The glass was then nucleated and crystallized based on differential thermal analysis (DTA) data and was characterized by {sup 29}Si, {sup 31}P, {sup 11}B and {sup 27}Al MAS-NMR. XRD and {sup 29}Si NMR showed that lithium metasilicate (Li{sub 2}SiO{sub 3}) is the first phase to c form followed by cristobalite (SiO{sub 2}) and lithium disilicate (Li{sub 2}Si{sub 2}O{sub 5}). {sup 29}Si MAS-NMR revealed a change in the network structure already for the glasses nucleated at 550 {sup o}C. Since crystalline Li{sub 3}PO{sub 4}, as observed by {sup 31}P MAS-NMR, forms concurrently with the silicate phases, we conclude that crystalline Li{sub 3}PO{sub 4} does not act as a nucleating agent for lithium silicate phases. Moreover, {sup 31}P NMR indicates the formation of M-PO{sub 4} (M=B, Al or Ti) complexes. The presence of BO{sub 3} and BO{sub 4} structural units in all the glass/glass-ceramic samples is revealed through {sup 11}B MAS-NMR. B remains in the residual glass and the crystallization of silicate phases causes a reduction in the number of alkali ions available for charge compensation. As a result, the number of trigonally coordinated B (BO{sub 3}) increases at the expense of tetrahedrally coordinated B (BO{sub 4}). The {sup 27}Al MAS-NMR spectra indicate the presence of tetrahedrally coordinated Al species, which are only slightly perturbed by the crystallization. - Graphical abstract: {sup 11}B MAS-NMR spectra of LAS glass heat treated at different temperatures, showing the evolution of the residual glass matrix during the crystallization treatment. High-field (18.8 T) NMR enables us to record high resolution spectra, from which the glass network modifications could be related to the formation of intermediate lithium silicate crystalline phases.

36 MATERIALS SCIENCE↗

Evidence of network demixing in GeS{sub 2}-Ga{sub 2}S{sub 3} chalcogenide glasses: A phase transformation study

The information of phase transformation is attained by in situ XRD experiments leading to the knowledge of topological threshold in GeS{sub 2}-Ga{sub 2}S{sub 3} glasses. The turning point of phase transformation behavior is demonstrated to be glasses containing 14-15 mol% Ga{sub 2}S{sub 3}. To interpret it a network demixing model is further improved and proposed for the structure of these ternary or quasi-binary chalcogenide glasses. For the nearest-neighbor coordination environment of glass with a transitional composition of 85.7 mol% (6/7) GeS{sub 2}.14.3 mol% (1/7) Ga{sub 2}S{sub 3}, six-coordinated [S{sub 3}Ga-X-GaS{sub 3}] units (X=S or None) are well isolated by the [GeS{sub 4}] structures, which contributes to the decreasing of precipitation of Ga{sub 2}S{sub 3} crystals in (100-x)GeS{sub 2}-xGa{sub 2}S{sub 3} (x{<=}14.3) glasses corresponding to the experimental evidence of the phase transformation behavior. This scenario of intermediate-range structural order, firstly, includes the arrangement of structural units which is consistent with and provides an atomistic explanation of the compositional evolution of phase transformation behavior in these glasses. -- Graphical abstract: Synopsis: network demixing in GeS{sub 2}-Ga{sub 2}S{sub 3} chalcogenide glasses. Display Omitted Highlights: {yields} Phase transformation in GeS{sub 2}-Ga{sub 2}S{sub 3} glasses. {yields} Turning point of the phase transformation behavior. {yields} Medium-range order structure of chalcogenide glasses. {yields} Network demixing model for GeS{sub 2}-Ga{sub 2}S{sub 3} glasses.

36 MATERIALS SCIENCE↗

Crystal development during carbonation of lime-based mortars in different environmental conditions

Highlights: • High CO{sub 2} and DiloCarb® treatment favour advanced carbonation and self-healing. • In the lime mortar without ceramics, channel type pores occur in the aggregate border. • In the lime mortars with ceramics, vug type pores are produced in the binder during kneading. • The formation of tabular CaCO{sub 3} polymorphs caused an increase in stress leading to microshrinkage cracks. • The use of a ceramic provoked dissolution and then re-precipitation of more stable polymorphs. - Abstract: This study examines crystal development during the carbonation of lime mortars according to the additives used and curing conditions. Two types of samples were prepared, one with sand and the other one additionally including Roman ceramics. These mortars were cured: 1) by spraying with a carbonation accelerator product under laboratory conditions; 2) in a climate chamber under 20 °C, 60% relative humidity, and 1600 ppm CO{sub 2}; and 3) under laboratory conditions as controls. Polarized light microscopy, SEM-EDS and XRD were used at 28, 90, 120 and 180 days to monitor the carbonation process. Observations indicate the development of different CaCO{sub 3} polymorphs, which appeared as metastable phases. The early nucleation of a well-defined calcite phase as the most stable CaCO{sub 3} polymorph was only identified in the chamber-cured samples. Differences in the pore network were observed depending on the composition and morphology of the mortar components and the environmental curing conditions.

36 MATERIALS SCIENCE↗

Methanol conversion to light olefins over nanostructured CeAPSO-34 catalyst: Thermodynamic analysis of overall reactions and effect of template type on catalytic properties and performance

Graphical abstract: In this research nanostructured CeAPSO-34 was synthesized to explore the effect of TEAOH and morpholine on its physiochemical properties and MTO performance. Prepared catalysts were characterized with XRD, FESEM, BET, FTIR and NH3-TPD techniques. The results indicated that the nature of the template determines the physiochemical properties of CeAPSO-34 due to different rate of crystal growth. The catalyst obtained by using morpholine showed longer life time as well as sustaining light olefins selectivity at higher values. Furthermore, a comprehensive thermodynamic analysis of overall reactions network was carried out to address the major channels of methanol to olefins conversion. - Highlights: • Introduction of Ce into SAPO-34 framework. • Comparison of CeAPSO-34 synthesized using morpholine and TEAOH. • The nature of the template determines the physiochemical properties of CeAPSO-34. • Morpholine enhances catalyst lifetime in MTO process. • Presenting a complete reaction network for MTO process. - Abstract: TEAOH and morpholine were employed in synthesis of nanostructured CeAPSO-34 molecular sieve and used in methanol to olefins conversion. Prepared samples were characterized by XRD, FESEM, EDX, BET, FTIR and NH{sub 3}-TPD techniques. XRD patterns reflected the higher crystallinity of the catalyst synthesized with morpholine. The FESEM results indicated that the nature of the template determines the morphology of nanostructured CeAPSO-34 due to different rate of crystal growth. There was a meaningful difference in the strength of both strong and weak acid sites for CeAPSO-34 catalysts synthesized with TEAOH and morpholine templates. The catalyst synthesized with morpholine showed higher desorption temperature of both weak and strong acid sites evidenced by NH{sub 3}-TPD characterization. The catalyst obtained using morpholine template had the longer lifetime and sustained desired light olefins at higher values. A comprehensive thermodynamic analysis of overall reactions network was carried out to address the major channels of methanol to olefins conversion.

36 MATERIALS SCIENCE↗

Revealing the relationship between liquid fragility and medium-range order in silicate glasses

Despite decades of studies, the nature of the glass transition remains elusive. In particular, the sharpness of the dynamical arrest of a melt at the glass transition is captured by its fragility. Here, we reveal that fragility is governed by the medium-range order structure. Based on neutron-diffraction data for a series of aluminosilicate glasses, we propose a measurable structural parameter that features a strong inverse correlation with fragility, namely, the average medium-range distance (MRD). We use in-situ high-temperature neutron-scattering data to discuss the physical origin of this correlation. We argue that glasses exhibiting low MRD values present an excess of small network rings. Such rings are unstable and deform more readily with changes in temperature, which tends to increase fragility. These results reveal that the sharpness of the dynamical arrest experienced by a silicate glass at the glass transition is surprisingly encoded into the stability of rings in its network.

36 MATERIALS SCIENCE↗

NASA Tech Briefs, December 2006

Topic include: Inferring Gear Damage from Oil-Debris and Vibration Data; Forecasting of Storm-Surge Floods Using ADCIRC and Optimized DEMs; User Interactive Software for Analysis of Human Physiological Data; Representation of Serendipitous Scientific Data; Automatic Locking of Laser Frequency to an Absorption Peak; Self-Passivating Lithium/Solid Electrolyte/Iodine Cells; Four-Quadrant Analog Multipliers Using G4-FETs; Noise Source for Calibrating a Microwave Polarimeter; Hybrid Deployable Foam Antennas and Reflectors; Coating MCPs with AlN and GaN; Domed, 40-cm-Diameter Ion Optics for an Ion Thruster; Gesture-Controlled Interfaces for Self-Service Machines; Dynamically Alterable Arrays of Polymorphic Data Types; Identifying Trends in Deep Space Network Monitor Data; Predicting Lifetime of a Thermomechanically Loaded Component; Partial Automation of Requirements Tracing; Automated Synthesis of Architecture of Avionic Systems; SSRL Emergency Response Shore Tool; Wholly Aromatic Ether-Imides as n-Type Semiconductors; Carbon-Nanotube-Carpet Heat-Transfer Pads; Pulse-Flow Microencapsulation System; Automated Low-Gravitation Facility Would Make Optical Fibers; Alignment Cube with One Diffractive Face; Graphite Composite Booms with Integral Hinges; Tool for Sampling Permafrost on a Remote Planet; and Special Semaphore Scheme for UHF Spacecraft Communications.

Source record↗

Hidden Superlattice in Tl2(SC6H4S) and Tl2(SeC6H4Se) Solved from Powder X-ray Diffraction

The crystal structures of the isostructural title compounds poly[({mu}-benzene-1,4-dithiolato)dithallium], Tl{sub 2}(SC{sub 6}H{sub 4}S), and poly[({mu}-benzene-1,4-diselenolato)dithallium], Tl{sub 2}(SeC{sub 6}H{sub 4}Se), were solved by simulated annealing from high-resolution synchrotron X-ray powder diffraction. Rietveld refinements of an initial structure with one formula unit per triclinic cell gave satisfactory agreement with the data, but led to a structure with impossibly close non-bonded contacts. A disordered model was proposed to alleviate this problem, but an alternative supercell structure leads to slightly improved agreement with the data. The isostructural superlattice structures were confirmed for both compounds through additional data collection, with substantially better counting statistics, which revealed the presence of very weak superlattice peaks not previously seen. Overall, each structure contains Tl-S or Tl-Se two-dimensional networks, connected by phenylene bridges. The sulfur (or selenium) coordination sphere around each thallium is a highly distorted square pyramid or a 'see-saw' shape, depending upon how many Tl-S or Tl-Se interactions are considered to be bonds. In addition, the two compounds contain pairs of Tl{sup I} ions that interact through a closed-shell 'thallophilic' interaction: in the sulfur compound there are two inequivalent pairs of Tl atoms with Tl-Tl distances of 3.49 and 3.58 {angstrom}, while in the selenium compound those Tl-Tl interactions are at 3.54 and 3.63 {angstrom}.

36 MATERIALS SCIENCE↗

Multi-scale structural analysis of swift heavy ion-irradiated ZrO 2 and HfO 2

The radiation-induced monoclinic-to-tetragonal phase transition in ZrO 2 and HfO 2 has been the subject of many investigations, but the transformation pathways and underlying structural mechanisms are still not well understood. In this study, microcrystalline powder samples of ZrO 2 and HfO 2 were irradiated with 946 MeV and 1470 MeV Au ions to a wide fluence range up to 3 × 10 13 ions/cm 2 . To characterize beam-induced structural modifications across all spatial length scales, complementary experimental techniques such as synchrotron X-ray diffraction and spallation neutron total scattering were used. The phase evolution of the tetragonal polymorph with increasing ion fluence is accurately described by a heterogeneous track-overlap model that incorporates both direct- and double-impact processes. These damage accumulation processes are an expression of a core-shell ion track morphology that depends on irradiation conditions and target material. Neutron pair distribution function analysis revealed that ion-beam-induced tetragonal ZrO 2 is merely a configurational average of short-range orthorhombic (Pbcn) domains stabilized by a dense network of domain walls. Furthermore, this knowledge is critical for a better understanding of how crystalline-to-crystalline phase transformations proceed at the atomic scale under extreme conditions.

Monoclinic-to-tetragonal phase transformation↗

Two Ce-containing 3D metal–organic frameworks: In situ formation of ligand (DDPD)

Hydrothermal reactions of cerium nitrate and 5-hydroxyisophthalic acid (OH-H{sub 2}BDC) produce two new metal–organic frameworks (MOFs), ([Ce(DDPD){sub 1.5}(H{sub 2}O){sub 2.5}]·4H{sub 2}O){sub n} (1) and ([Ce(OH-BDC)(OH-HBDC)(H{sub 2}O){sub 2}]·2H{sub 2}O]{sub n} (2) (DDPD(II)=5,10-dioxo-5,10-dihydro-4,9-dioxapyrene-2,7-dicarboxylate(II)). These two complexes have been characterized by elemental analysis, IR, TG, and single-crystal X-ray diffraction. It was remarkable that the in situ reaction of OH-H{sub 2}BDC to DDPD(II) was found in complex 1. In 1, Ce(III) ions are bridged by DDPD ligands to form infinite 1D chain, which is further connected via DDPD ligands to form 3D structure. Complex 2 possesses a neutral noninterpenetrating 2D layer structure. Furthermore, the fluorescence properties and magnetic behavior of 1 and 2 have been investigated. - Graphical abstract: In complex 1, the in situ reaction of OH-H{sub 2}BDC to DDPD(II) was found. Complex 1 features a 3D network structure. Adjacent Ce(III) ions are bridged by two carboxylate groups to form a 1D infinite inorganic chain, and further linked by the DDPD(II) ligands. Display Omitted - Highlights: • Complexes 1 and 2 was synthesized via hydrothermal methods. • In situ reaction of OH-H{sub 2}BDC to DDPD(II) was found in complex 1. • Ce(III) ions are bridged by the DDPD(II) ligands to generate a 3D structure in complex 1. • Complex 2 possesses a neutral noninterpenetrating 2D layer structure. • Fluorescent properties and magnetic behavior of 1 and 2 have been studied.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Novel organic–inorganic amorphous photoactive hybrid films with rare earth (Eu{sup 3+}, Tb{sup 3+}) covalently embedded into silicon–oxygen network via sol–gel process

Highlights: • The hybrids are prepared through the hydrolysis and condensation process. • The hybrids are amorphous and heat stabilized. • The hybrids containing Eu{sup 3+} and Tb{sup 3+} show the typical red and green emissions. - Abstract: Novel organic–inorganic hybrid amorphous thin films were synthesized by linking lanthanide (Tb{sup 3+}, Eu{sup 3+}) complexes through 3,4-bis(3-(triethoxysilyl)propylcarbamoyloxy)benzoic acid using sol–gel method. These inorganic–organic hybrids were characterized in detail by Fourier transform infrared spectroscopy, wide angle X-ray diffraction, themogravimetric analysis, scanning electron microscope, and fluorescence spectra. The above research results indicate that the hybrids possess high thermal-stability, amorphous structure features and especially favorable luminescent performances, such as long luminescent decay lifetime, high quantum yield etc.

36 MATERIALS SCIENCE↗

Three-dimensional analysis by serial sectioning of cubic zirconia sinters

Three-dimensional electron backscatter diffraction technique was used for the characterization of grain boundary geometry and pore morphology in cubic zirconia. A set of three samples composed of cubic yttria stabilized zirconia, sintered under different conditions was investigated. Analysis of grain boundaries and pore structure was carried out in a dual-beam scanning electron microscope. For each sample, a volume of 15·10{sup 3} μm{sup 3} was investigated. The results of three-dimensional microstructure analysis were compared to the results derived from regular, two-dimensional maps of the area of 2500 µm{sup 2}. Based on two-dimensional and three-dimensional data the average grain diameter, number of grains, average number of neighbors and porosity were calculated. The average grain diameter varied in the range from 2.39 µm to 2.91 µm and from 3.00 µm to 3.79 µm, while the level of porosity varied in the range from 1.22% to 1.77% and from 1.30% to 5.61% for two-dimensional and three-dimensional data, respectively. The analysis of grain boundary networks revealed a strong dependence between grain boundary density and sample preparation parameters. The parameters of the sintering process affected also the size and distribution of pores. The comparison of the results of 2D and 3D materials characterization revealed significant differences in the values of calculated microstructure parameters.

36 MATERIALS SCIENCE↗

Effects of Molecular Weight on poly( -pentadecalactone) Mechanical and Thermal Properties

A series of poly({omega}-pentadecalactone) (PPDL) samples, synthesized by lipase catalysis, were prepared by systematic variation of reaction time and water content. These samples possessed weight-average molecular weights (M{sub w}), determined by multi-angle laser light scattering (MALLS), from 2.5 x 10{sup 4} to 48.1 x 10{sup 4}. Cold-drawing tensile tests at room temperature of PPDL samples with M{sub W} between 4.5 x 10{sup 4} and 8.1 x 10{sup 4} showed a brittle-to-ductile transition. For PPDL with M{sub W} of 8.1 x 10{sup 4}, inter-fibrillar slippage dominates during deformation until fracture. Increasing M{sub W} above 18.9 x 10{sup 4} resulted in enhanced entanglement network strength and strain-hardening. The high M{sub W} samples also exhibited tough properties with elongation at break about 650% and tensile strength about 60.8 MPa, comparable to linear high density polyethylene (HDPE). Relationships among molecular weight, Young's modulus, stress, strain at yield, melting and crystallization enthalpy (by differential scanning calorimetry, DSC) and crystallinity (from wide-angle X-ray diffraction, WAXD) were correlated for PPDL samples. Similarities and differences of linear HDPE and PPDL molecular weight dependence on their mechanical and thermal properties were also compared.

59 BASIC BIOLOGICAL SCIENCES↗