Search NASA⌕ Search

SEARCH · Search NASA

Results for “flat geometry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

LES simulations of a vacuum membrane distillation channel with geometric alterations

3D LES simulations were carried out to study the performance of a vacuum membrane distillation module. A wiggly wall profile with/without embedded stiffeners was considered to alleviate axial and radial temperature polarization, the cause of performance decrease in membrane distillation. Results of the flow field show the wiggles create unsteady vortex shedding inducing intense mixing in the channel. Vortex shedding intensity increases as the Reynolds number increases or stiffeners are added. 3D results show a 56% improvement in flux when moving from a flat sheet membrane to a wiggly membrane with stiffeners at a constant Reynolds number, corresponding to an improvement from 11.7 to 41.7 in the Nusselt number, showing that the alterations improved the flux performance by enhancing the heat transfer along the membrane surface and therefore alleviating temperature polarization, a critical bottleneck in membrane distillation systems. Further, a merit criterion was defined based on the Nusselt number and friction factor, and a 40% increase in merit was shown switching from a flat to a wiggly channel, while a 97% merit increase was seen going from flat to wiggly with stiffeners. A 42% enhancement in the flux was also seen moving from a straight channel to a wiggly channel at a higher Reynolds number which highlights the importance of strategically choosing the mass flow rate, as well as inducing flow separation and vortex shedding in the channel to promote mixing and dissipate the thermal boundary layer. The variation in results between the wiggly module with stiffeners and the wiggly module at high Reynolds numbers suggests enhancing mixing structures can be more impactful on flux for this geometry than increasing the flow rate to a turbulent/transitional regime. However, both are preferable for peak system flux performance. Furthermore, a 2D approximation was used to perform simulations on more extended channels to examine the length degradation. The modules with wiggly channels performed at the same flux level with a doubling of the length. On the other hand, the flat sheet modules experienced length degradation by temperature polarization and dropped in flux yield by around 13% of the short-channel value. This work illustrates that modeling the system and understanding how the performance decreases as the membrane surface area increases are critical for a larger module (scaling up from a lab to a prototype module) to maintain high flux performance.

42 ENGINEERING↗

Solving Inverse Detection Problems Using Passive Radiation Signatures [Slides]

The ability to reconstruct an unknown radioactive object based on its passive gamma-ray and neutron signatures is very important in homeland security applications. Often in the analysis of unknown radioactive objects, for simplicity or speed or because there is no other information, they are modeled as spherically symmetric regardless of their actual geometry. In these presentation we discuss the accuracy and implications of this approximation for decay gamma rays and for neutron-induced gamma rays. We discuss an extension of spherical raytracing (for uncollided fluxes) that allows it to be used when the exterior shielding is flat or cylindrical. We revisit some early results in boundary perturbation theory, showing that the Roussopolos estimate is the correct one to use when the quantity of interest is the flux or leakage on the boundary. We apply boundary perturbation theory to problems in which spherically symmetric systems are perturbed in asymmetric nonspherical ways. We apply mesh adaptive direct search (MADS) algorithms to object reconstructions. We present a benchmark test set that may be used to quantitatively evaluate inverse detection methods.

42 ENGINEERING↗

TH-AB-209-01: Making Benchtop X-Ray Fluorescence Computed Tomography (XFCT) Practical for in Vivo Imaging by Integration of a Dedicated High-Performance X-Ray Source in Conjunction with Micro-CT Functionality

Purpose: To make benchtop x-ray fluorescence computed tomography (XFCT) practical for routine preclinical imaging tasks with gold nanoparticles (GNPs) by deploying, integrating, and characterizing a dedicated high-performance x-ray source and addition of simultaneous micro-CT functionality. Methods: Considerable research effort is currently under way to develop a polychromatic benchtop cone-beam XFCT system capable of imaging GNPs by stimulation and detection of gold K-shell x-ray fluorescence (XRF) photons. Recently, an ad hoc high-power x-ray source was incorporated and used to image the biodistribution of GNPs within a mouse, postmortem. In the current work, a dedicated x-ray source system featuring a liquid-cooled tungsten-target x-ray tube (max 160 kVp, ∼3 kW power) was deployed. The source was operated at 125 kVp, 24 mA. The tube’s compact dimensions allowed greater flexibility for optimizing both the irradiation and detection geometries. Incident x-rays were shaped by a conical collimator and filtered by 2 mm of tin. A compact “OEM” cadmium-telluride x-ray detector was implemented for detecting XRF/scatter spectra. Additionally, a flat panel detector was installed to allow simultaneous transmission CT imaging. The performance of the system was characterized by determining the detection limit (10-second acquisition time) for inserts filled with water/GNPs at various concentrations (0 and 0.010–1.0 wt%) and embedded in a small-animal-sized phantom. The phantom was loaded with 0.5, 0.3, and 0.1 wt% inserts and imaged using XFCT and simultaneous micro-CT. Results: An unprecedented detection limit of 0.030 wt% was experimentally demonstrated, with a 33% reduction in acquisition time. The reconstructed XFCT image accurately localized the imaging inserts. Micro-CT imaging did not provide enough contrast to distinguish imaging inserts from the phantom under the current conditions. Conclusion: The system is immediately capable of in vivo preclinical XFCT imaging with GNPs. Micro-CT imaging will require optimization of irradiation parameters to improve contrast. Supported by NIH/NCI grant R01CA155446; This investigation was supported by NIH/NCI grant R01CA155446.

60 APPLIED LIFE SCIENCES↗

Stabilized Acoustic Levitation of Dense Materials Using a High-Powered Siren

Stabilized acoustic levitation and manipulation of dense (e.g., steel) objects of 1 cm diameter, using a high powered siren, was demonstrated in trials that investigated the harmonic content and spatial distribution of the acoustic field, as well as the effect of sample position and reflector geometries on the acoustic field. Although further optimization is possible, the most stable operation achieved is expected to be adequate for most containerless processing applications. Best stability was obtained with an open reflector system, using a flat lower reflector and a slightly concave upper one. Operation slightly below resonance enhances stability as this minimizes the second harmonic, which is suspected of being a particularly destabilizing influence.

Gammell, P. M.↗

Coaxial atomizer liquid intact lengths

Average intact lengths of round liquid jets generated by airblast coaxial atomizer were measured from over 1500 photographs. The intact lengths were studied over a jet Reynolds number range of 18,000 and Weber number range of 260. Results are presented for two different nozzle geometries. The intact lengths were found to be strongly dependent on Re and We numbers. An empirical equation was derived as a function of these parameters. A comparison of the intact lengths for round jets and flat sheets shows that round jets generate shorter intact lengths.

Eroglu, Hasan↗

The Properties of Flowing Sheets Formed by Impingement of Liquid Jets on Curved Surfaces

An applied research program was conducted to determine the properties of flat sheets of propellants formed by directing jets of liquid tangentially against concave, cylindrical deflector surfaces. The dimensions and spatial orientation of the resultant sheets were found to depend only on the orifice diameter and deflector geometry for three propellant simulants of widely-varying physical properties, over the range of injection velocities encountered in liquid rocket engines. Correlating equations, suitable for use in injector design, are presented for free-sheet width and spreading angle. Distribution of mass and velocity across the free-flowing sheets is also reported. Conditions were discovered under which true sheets do not form, or at best malformed or pulsating sheets result. An envelope of geometrical constraints for deflector design is tentatively defined in order to avoid these undesirable operating regions. The results of the present cold-flow tests are compared with firing test data for impinging-sheet injectors and combustion performance is related to single sheet behavior.

Riebling, Robert W.↗

A new class of tandems: Optically coupled III-V/silicon module with outdoor efficiency exceeding 30%

The aim of this project was to introduce a new class of technology—that of high-efficiency silicon-based tandem photovoltaic (PV) modules—that, with follow-on development, has a clear path to reduced levelized cost of electricity (LCOE) for utility-scale power generation. In particular, the objective of the project was to demonstrate the first 30%-efficient III-V/silicon module in outdoor conditions using a tandem geometry in which the sub-cells are detached physically but coupled optically. In present PV power plants installed in the US, the module makes up only approximately one-third of the cost; area-dependent balance-of-systems (BOS) costs such as installation materials, labor, land, and site prep made up an additional third, and area-independent BOS costs round out the final third. With this pricing structure, (annually averaged) module efficiency is a clear market driver: increase the annual energy output per module and the effective costs translated into $/W of both the module and the area-dependent BOS—two-thirds of the total cost—decrease proportionately. However, the dominant PV technology—flat-plate silicon modules—is reaching its theoretical efficiency limit, and thus a tandem technology in which silicon is coupled with a wider-bandgap cell is a promising route to remain responsive to market forces. As it is not trivial to couple silicon with other cells in conventional two-terminal geometries due to, e.g., lattice mismatch, this project introduced a new, four-terminal configuration using a “PVMirror.” A PVMirror utilizes PV cells as a three-in-one technology—they act as a concentrating mirror, spectrum splitter, and high-efficiency light-to-electricity converter. Light is incident upon a full-aperture dichroic mirror that reflects visible light and transmits infrared light. The transmitted light is absorbed in silicon PV cells that are placed behind the dichroic mirror and that convert IR photons to electricity with high efficiency. The dichroic mirror and silicon PV cells are affixed to a curved glass trough that tracks the sun about a single, North-South axis such that the reflected VIS light is concentrated at a common line focus, at which is placed a second, wider-bandgap GaAs PV cell having high efficiency at shorter wavelengths. The innovation of PVMirrors lies in their design, which maximizes annual energy output and minimizes the constraints placed on the sub-cells. In particular, the cells are free of lattice- and current-matching restrictions, neither cell requires a transparent rear electrode, and either sub-cell can be placed at the focus depending on their relative costs. Furthermore, the greatest benefit of PVMirrors is that they make use of a portion of the diffuse light whereas concentrator tandems cannot. This results in a benefit in energy yield and extends PVMirrors’ competitive range. Over the course of this one-year project, a silicon PVMirror and GaAs receiver were fabricated, characterized, and placed outdoors on a sun tracker, where the efficiency of the tandem “module” was measured for three days. Notable results include the first demonstration of this flexible tandem configuration, a maximum tandem efficiency of 29.6% (just shy of the 30% overall project goal), successful conversion of diffuse light into electricity, a thorough loss analysis indicating a path to over 31% efficiency, and a roadmap to cost-competitive PVMirror tandems using a wide-bandgap polycrystalline PVMirror and a silicon receiver. Development of a >18%-efficient wide-bandgap polycrystalline cell—the key enabler of this envisioned tandem—should be a future research focus. This project has laid the groundwork for a PV technology that, with continued development, has the potential to reach LCOEs as low as $0.03/kWh according to our calculations. Such a system would provide the public with inexpensive, clean solar power.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Adsorbed states of chlorophenol on Cu(110) and controlled switching of single-molecule junctions

A molecular junction of substituted benzene (chlorophenol) is fabricated and controlled by using a scanning tunneling microscope (STM). Prior to the junction formation, the bonding geometry of the molecule on the surface is characterized by STM and electron energy loss spectroscopy (EELS). EELS shows that the OH group of chlorophenol is dissociated on Cu(110) and that the molecule is bonded nearly flat to the surface via an O atom, with the Cl group intact. We demonstrate controlled contact of an STM tip to the “available” Cl group and lift-up of the molecule while it is anchored to the surface via an O atom. The asymmetric bonding motifs of the molecule to the electrodes allow for reversible control of the junction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DO WE REALLY KNOW THE DUST? SYSTEMATICS AND UNCERTAINTIES OF THE MID-INFRARED SPECTRAL ANALYSIS METHODS

The spectral region around 10 {mu}m, showing prominent emission bands from various dust species is commonly used for the evaluation of the chemical composition of protoplanetary dust. Different methods of analysis have been proposed for this purpose, but so far, no comparative test has been performed to test the validity of their assumptions. In this paper, we evaluate how good the various methods are in deriving the chemical composition of dust grains from infrared spectroscopy. Synthetic spectra of disk models with different geometries and central sources were calculated, using a two-dimensional radiative transfer code. These spectra were then fitted in a blind test by four spectral decomposition methods. We studied the effect of disk structure (flared versus flat), inclination angle, size of an inner disk hole, and stellar luminosity on the fitted chemical composition. Our results show that the dust parameters obtained by all methods deviate systematically from the input data of the synthetic spectra. The dust composition fitted by the new two-layer temperature distribution method, described in this paper, differs the least from the input dust composition and the results show the weakest systematic effects. The reason for the deviations of the results given by the previously used methods lies in their simplifying assumptions. Due to the radial extent of the 10 {mu}m emitting region there is dust at different temperatures contributing to the flux in the silicate feature. Therefore, the assumption of a single averaged grain temperature can be a strong limitation of the previously used methods. The continuum below the feature can consist of multiple components (e.g., star, inner rim, and disk midplane), which cannot simply be described by a Planck function at a single temperature. In addition, the optically thin emission of 'featureless' grains (e.g., carbon in the considered wavelength range) produces a degeneracy in the models with the optically thick emission of the disk. The effect of different noise levels on the results has also been tested. We find that for a signal-to-noise ratio (S/N) of 100 one can expect an absolute uncertainty in the value of the crystallinity of about 11% using ground-based observations (8-13 {mu}m). For space-based observations (7-17 {mu}m) the expected uncertainty is about 5% for the same S/N value. Moreover, the average value of the estimated crystallinity increases toward lower S/N in general. On the basis of our results, we propose a recipe for the analysis and interpretation of dust spectroscopy data in the mid-infrared which should be especially valuable for analyzing Spitzer spectroscopy data and ground-based infrared spectroscopy data in the 10 {mu}m window.

99 GENERAL AND MISCELLANEOUS↗

Characterization of the plasma current quench during disruptions in the National Spherical Torus Experiment

A detailed analysis of the plasma current quench in the National Spherical Torus Experiment [M.Ono, et al Nuclear Fusion 40, 557 (2000)] is presented. The fastest current quenches are fit better by a linear waveform than an exponential one. Area-normalized current quench times down to .4 msec/m2 have been observed, compared to the minimum of 1.7 msec/m2 recommendation based on conventional aspect ratio tokamaks; as noted in previous ITPA studies, the difference can be explained by the reduced self-inductance at low aspect ratio and high-elongation. The maximum instantaneous dIp/dt is often many times larger than the mean quench rate, and the plasma current before the disruption is often substantially less than the flat-top value. The poloidal field time-derivative during the disruption, which is directly responsible for driving eddy currents, has been recorded at various locations around the vessel. The Ip quench rate, plasma motion, and magnetic geometry all play important roles in determining the rate of poloidal field change.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The Anatomy of an Unusual Edge-on Protoplanetary Disk. I. Dust Settling in a Cold Disk

As the earliest stage of planet formation, massive, optically thick, and gas-rich protoplanetary disks provide key insights into the physics of star and planet formation. When viewed edge-on, high-resolution images offer a unique opportunity to study both the radial and vertical structures of these disks and relate this to vertical settling, radial drift, grain growth, and changes in the midplane temperatures. In this work, we present multi-epoch Hubble Space Telescope and Keck scattered light images, and an Atacama Large Millimeter/submillimeter Array 1.3 mm continuum map for the remarkably flat edge-on protoplanetary disk SSTC2DJ163131.2–242627, a young solar-type star in ρ Ophiuchus. We model the 0.8 μm and 1.3 mm images in separate Markov Chain Monte Carlo (MCMC) runs to investigate the geometry and dust properties of the disk using the MCFOST radiative transfer code. In scattered light, we are sensitive to the smaller dust grains in the surface layers of the disk, while the submillimeter dust continuum observations probe larger grains closer to the disk midplane. An MCMC run combining both data sets using a covariance-based log-likelihood estimation was marginally successful, implying insufficient complexity in our disk model. The disk is well characterized by a flared disk model with an exponentially tapered outer edge viewed nearly edge-on, though some degree of dust settling is required to reproduce the vertically thin profile and lack of apparent flaring. A colder than expected disk midplane, evidence for dust settling, and residual radial substructures all point to a more complex radial density profile to be probed with future, higher-resolution observations.

47 OTHER INSTRUMENTATION↗

Optimization of Slosh Baffle Geometry

This paper describes a method for determining the optimum baffle configuration for suppressing excessive propellant sloshing in the tanks of a large launch vehicle. The optimum geometry for a baffle system is considered to be the one with the least mass which is capable of providing the necessary damping. The analysis considers a cylindrical tank and a baffle system made up of several flat ring baffles mounted horizontally. The basic assumptions are discussed and derivations given of the equations necessary to predict the optimum baffle configuration consistent with adequate strength. Numerical results are presented graphically, and some general conclusions are drawn.

OPTIMIZATION↗

Reinforcement of metals with advanced filamentary composites

This paper reviews some recent applications of the concept of reinforcing metal structures with advanced filamentary composites, and presents some results of an experimental investigation of the tensile behavior of aluminum and titanium reinforced with unidirectional boron/epoxy. Results are given for tubular and flat specimens, bonded at either room temperature or elevated temperature. The composite reinforced metals showed increased stiffness over the all-metal counterpart, as predicted by the rule of mixtures, and the results were independent of specimen geometry. The tensile strength of the born/epoxy reinforced metals is shown to be a function of the geometry of the test specimen and the method of bonding the composite to the metal.

Herakovich, C. T.↗

Near-wall turbulence alteration through thin streamwise riblets

The possibility of improving the level of drag reduction associated with near-wall riblets is considered. The methodology involves the use of a hot-wire anemometer to study various surface geometries on small, easily constructed models. These models consist of small, adjacent rectangular channels on the wall aligned in the streamwise direction. The VITA technique is modified and applied to thin-element-array and smooth flat-plate data and the results are indicated schematically.

Wilkinson, Stephen P.↗

An Overview of Observations of Mars' North Polar Region From the Mars Global Surveyor Laser Altimeter

Since its arrival at Mars on September l5, 1997, the Mars Global Surveyor (MGS) has been in a near-polar elliptical orbit, with the orbital eccentricity decreasing during orbital periapse passes where the spacecraft aerobrakes through the martian atmosphere. The Mars Orbiter Laser Altimeter (MOLA), an instrument on the MGS, has the ability to range to the martian surface during nonaerobraking passes. MOLA can operate whenever the range from the spacecraft to the surface is less than 786 km, with the limit determined by the number of bits encoded for the range measurement During the capture orbit, aerobraking hiatus, and science phasing orbit (SPO) mission phases, MOLA acquired approximately 200 profiles across the northern hemisphere of Mars and provided more than 2,000,000 measurements of the radius of the planet. These observations cover the region from the north pole to about 10 degrees S latitude with a precision of a few tens of centimeters and an accuracy (at present) of about 30 in. Absolute accuracy of the elevations is limited by the knowledge of the MGS orbits; these should improve later in the mission due to a more optimal tracking geometry, an improved gravitational field, and the use of the high-gain antenna once the spacecraft achieves its approximately 400-km-altitude circular mapping orbit. MOLA measurements so far show a planet with a low, flat high-latitude region in the north and a higher, topographically rougher terrain nearer the equator. The north polar cap stands approximately 2-3 km above the surrounding terrain and displays deep chasms and complex structure. MOLA measurements of elevation, 1064-nm reflectivity, and backscattered pulse width indicate that the layered terrains are composed mainly of ice.

Smith, D. E.↗

Friction reduction for engine components

The present invention relates to techniques for lowering friction between moving surfaces of, for example, an internal combustion engine. Friction reduction is achieved by adding texture modifications to surfaces that come in contact with each other. Texture modifications that reduce friction in accordance with the present invention include dimples of varying geometries and depths ion the surfaces of components. The present invention also relates to the fabrication technique for applying the textures to the surfaces. In another embodiment, the patterned soft mask is applied onto a large surface (flat or curved including cylindrical rollers surfaces) to be followed by electrochemical etching to imprint the textures onto the component. And, in another embodiment, a diamond-like-carbon (DLC) film may be applied to the turbine component to also reduce friction.

Hsu, Stephen M.↗

Friction reduction for engine components

The present invention relates to techniques for lowering friction between moving surfaces of, for example, an internal combustion engine. Friction reduction is achieved by adding texture modifications to surfaces that come in contact with each other. Texture modifications that reduce friction in accordance with the present invention include dimples of varying geometries and depths ion the surfaces of components. The present invention also relates to the fabrication technique for applying the texture to the surfaces. In another embodiment, the patterned soft mask is applied onto a large surface (flat or curved including cylindrical rollers surfaces) to be followed by electrochemical etching to imprint the textures onto the component And, in another embodiment, a diamond-like-carbon (DLC) film may be applied to the turbine component to also reduce friction.

Hsu, Stephen M.↗

Planck 2015 results: XVIII. Background geometry and topology of the Universe

We report that maps of cosmic microwave background (CMB) temperature and polarization from the 2015 release of Planck data provide the highestquality full-sky view of the surface of last scattering available to date. This enables us to detect possible departures from a globally isotropic cosmology. We present the first searches using CMB polarization for correlations induced by a possible non-trivial topology with a fundamental domain that intersects, or nearly intersects, the last-scattering surface (at comoving distance χ rec ), both via a direct scan for matched circular patterns at the intersections and by an optimal likelihood calculation for specific topologies. We specialize to flat spaces with cubic toroidal (T3) and slab (T1) topologies, finding that explicit searches for the latter are sensitive to other topologies with antipodal symmetry. These searches yield no detection of a compact topology with a scale below the diameter of the last-scattering surface. The limits on the radius R i of the largest sphere inscribed in the fundamental domain (at log-likelihood ratio ΔlnL > -5 relative to a simply-connected flat Planck best-fit model) are: R i > 0.97 χ rec for the T3 cubic torus; and R i > 0.56 χ rec for the T1 slab. The limit for the T3 cubic torus from the matched-circles search is numerically equivalent, R i > 0.97 χ rec at 99% confidence level from polarization data alone. We also perform a Bayesian search for an anisotropic global Bianchi VII h geometry. In the non-physical setting, where the Bianchi cosmology is decoupled from the standard cosmology, Planck temperature data favour the inclusion of a Bianchi component with a Bayes factor of at least 2.3 units of log-evidence. However, the cosmological parameters that generate this pattern are in strong disagreement with those found from CMB anisotropy data alone. Fitting the induced polarization pattern for this model to the Planck data requires an amplitude of -0.10 ± 0.04 compared to the value of + 1 if the model were to be correct. In the physically motivated setting, where the Bianchi parameters are coupled and fitted simultaneously with the standard cosmological parameters, we find no evidence for a Bianchi VII h cosmology and constrain the vorticity of such models to (ω/H) 0 < 7.6 × 10 -10 (95% CL).

79 ASTRONOMY AND ASTROPHYSICS↗