Search NASA⌕ Search

SEARCH · Search NASA

Results for “friction experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Constitutive modelling of lubricants in concentrated contacts at high slide to roll ratios

A constitutive lubricant friction model for rolling/sliding concentrated contacts such as gears and cams was developed, based upon the Johnson and Tevaarwerk fluid rheology model developed earlier. The friction model reported herein differs from the earlier rheological models in that very large slide to roll ratios can now be accommodated by modifying the thermal response of the model. Also the elastic response of the fluid has been omitted from the model, thereby making it much simpler for use in the high slide to roll contacts. The effects of this simplification are very minimal on the outcome of the predicted friction losses (less than 1%). In essence then the lubricant friction model developed for the high slide to roll ratios treats the fluid in the concentrated contact as consisting of a nonlinear viscous element that is pressure, temperature, and strain rate dependent in its shear response. The fluid rheological constants required for the prediction of the friction losses at different contact conditions are obtained by traction measurements on several of the currently used gear lubricants. An example calculation, using this model and the fluid parameters obtained from the experiments, shows that it correctly predicts trends and magnitude of gear mesh losses measured elsewhere for the same fluids tested here.

Tevaarwerk, J. L.↗

Flowfield analysis of modern helicopter rotors in hover by Navier-Stokes method

The viscous, three-dimensional, flowfields of UH60 and BERP rotors are calculated for lifting hover configurations using a Navier-Stokes computational fluid dynamics method with a view to understand the importance of planform effects on the airloads. In this method, the induced effects of the wake, including the interaction of tip vortices with successive blades, are captured as a part of the overall flowfield solution without prescribing any wake models. Numerical results in the form of surface pressures, hover performance parameters, surface skin friction and tip vortex patterns, and vortex wake trajectory are presented at two thrust conditions for UH60 and BERP rotors. Comparison of results for the UH60 model rotor show good agreement with experiments at moderate thrust conditions. Comparison of results with equivalent rectangular UH60 blade and BERP blade indicates that the BERP blade, with an unconventional planform, gives more thrust at the cost of more power and a reduced figure of merit. The high thrust conditions considered produce severe shock-induced flow separation for UH60 blade, while the BERP blade develops more thrust and minimal separation. The BERP blade produces a tighter tip vortex structure compared with the UH60 blade. These results and the discussion presented bring out the similarities and differences between the two rotors.

Srinivasan, G. R.↗

Dynamical Heating from Dark Compact Objects and Axion Minihalos: Implications for the 21-cm Signal

The temperature of baryons at the end of the cosmic dark ages can be inferred from observations of the 21-cm hyperfine transition in neutral hydrogen. Any energy injection from the dark sector can therefore be detected through these measurements. Dark compact objects and dark-matter substructures can modify the baryon temperature by transferring heat via dynamical friction. In this work, we evaluate the prospects for detecting dynamical friction-induced heating from dark compact objects with a mass in the range $10^2 M_{\odot}$ to $10^5 M_{\odot}$, as well as from axion minihalos, using upcoming 21-cm experiments. We find that both the 21-cm global signal and power-spectrum measurements will be sensitive to dark compact objects that constitute about 10% of the dark matter, and will substantially improve our sensitivity to axion-like particles with masses in the range $10^{-18}$ eV to $10^{-9}$ eV.

Bhalla, Badal [Oklahoma U.] (ORCID:000000030488664↗

Planetary and Primitive Object Strength Measurements and Sampling Apparatus

We present experimental data and a model for the low-velocity (subsonic, 0 - 1000 m/s) penetration of brittle materials by both solid and hollow (i.e., coring) penetrators. The experiments show that penetration is proportional to momentum/frontal area of the penetrator. Because of the buildup of a cap in front of blunt penetrators, the presence or absence of a streamlined or sharp front end usually has a negligible effect for impact into targets with strength. The model accurately predicts the dependence of penetration depth on the various parameters of the target-penetrator system, as well as the qualitative condition of the target material ingested by a corer. In particular, penetration depth is approximately inversely proportional to the static bearing strength of the target. The bulk density of the target material has only a small effect on penetration, whereas friction can be significant, especially at higher impact velocities, for consolidated materials. This trend is reversed for impacts into unconsolidated materials. The present results suggest that the depth of penetration is a good measure of the strength, but not the density, of a consolidated target. Both experiments and model results show that, if passage through the mouth of a coring penetrator requires initially porous target material to be compressed to less than 26% porosity, the sample collected by the corer will be highly fragmented. If the final porosity remains above 26%, then most materials, except cohesionless materials, such as dry sand, will be collected as a compressed slug of material.

Ahrens, Thomas J.↗

On-orbit coldwelding: Fact or friction?

A study into the potential of on-orbit coldwelding occurring was completed. No instances of cold welding were found during deintegration and subsequent testing and analysis of LDEF hardware. This finding generated wide interest and indicated the need to review previous on-orbit coldwelding experiments and on-orbit spacecraft anomalies to determine whether the absence of coldwelding on LDEF was to be expected. Results show that even though there have been no documented cases of significant on-orbit coldwelding events occurring, precautions should be taken to ensure that neither coldwelding nor galling occurs in the space or prelaunch environment.

Dursch, Harry↗

Atmospheric tides on Venus. III - The planetary boundary layer

Diurnal solar heating of Venus' surface produces variable temperatures, winds, and pressure gradients within a shallow layer at the bottom of the atmosphere. The corresponding asymmetric mass distribution experiences a tidal torque tending to maintain Venus' slow retrograde rotation. It is shown that including viscosity in the boundary layer does not materially affect the balance of torques. On the other hand, friction between the air and ground can reduce the predicted wind speeds from about 5 to about 1 m/sec in the lower atmosphere, more consistent with the observations from Venus landers and descent probes. Implications for aeolian activity on Venus' surface and for future missions are discussed.

Dobrovolskis, A. R.↗

Friction in rail guns

The influence of friction is included in the present equations describing the performance of an inductively driven rail gun. These equations, which have their basis in an empirical formulation, are applied to results from two different experiments. Only an approximate physical description of the problem is attempted, in view of the complexity of details in the interaction among forces of this magnitude over time periods of the order of milisecs.

Kay, P. K.↗

Waves in Venus's middle and upper atmosphere - Implications of Pioneer Venus probe data above the clouds

This paper reevaluates Pioneer Venus probe data which show the presence of waves in Venus's middle and upper atmosphere. The data are extended to 138 km. Uncertainties in the temperature are typically about 0.1 times amplitude, supporting the reliability of large-amplitude oscillations approaching 40 K at 120 km. Growth rates above 100 km follow approximately the inverse square root of density and 'saturation' occurs. The waves then break at the 120 km level, providing a source for the 'friction' required in models to match the observed day-night temperature contrast in the lower thermosphere. The data correlated to an unexpected degree with temperatures from the Pioneer Venus orbiter atmospheric drag experiment. The observations lead to the suggestion that the thermospheric waves are solar-fixed, induced either by the major subsidence across the termination or as continuation upward of waves in the middle atmosphere.

Seiff, Alvin↗

DEVELOPMENT OF AN APPROACH TO MODELING LOADING AND ELUTION OF SPHERICAL RESORCINOL FORMALDEHYDE ION-EXCHANGE RESIN

The current strategy for removal of cesium from the Hanford waste stream is ion-exchange using spherical Resorcinol-Formaldehyde (sRF) resin. The original resin of choice was granular SuperLig 644 resin and during testing of this resin several operational issues were identified. For example, the granular material had a high angle of internal friction resulting in fragmentation of resin particles along its edges during cycling and adverse hydraulic performance. Efforts to replace SuperLig 644 were undertaken and one candidate was the granular Resorcinol-Formaldehyde (RF) resin where experience with this cation exchanger dates back to the late 1940's. To minimize hydraulic concerns a spherical version of RF was developed and several different chemically produced batches were created. The 5E-370/641 batch of sRF was selected and for the last decade numerous studies have been performed (e.g., batch contact tests, column loading and elution tests). The Waste Treatment Plant (WTP) flowsheet shows that the aqueous phase waste stream will have a wide range of ionic concentrations (e.g., during the loading step 0-3 M free OH, 5+ M Na, 0-1 M K, 0-3 M NO{sub 3}). Several steps are required in the ion-exchange process to achieve the required Cs separation factors: loading, displacement, washing, elution, and regeneration. The sRF resin will be operated over a wide range in pH (i.e., pH of 12-14 during the loading step and pH of 0.01-1 during the elution step). During some of these steps very high levels of counter-ions and co-ions will be present within the aqueous phase. Alternative process feeds are under consideration as well (e.g., sodium levels as high as 8 M and column operation up to 45 C during loading, reduced and recycled HNO{sub 3} during elution). In order to model the performance of sRF resin through an entire ion-exchange cycle, a more robust isotherm model is required. To achieve this more robust isotherm model requires knowledge of the numbers and kinds of fixed ionogenic groups that make up sRF. Recent literature reviews and scoping titration tests strongly indicate that sRF is a polyfunctional cation exchange resin with at least three dominant types of ring groups playing a role in its isotherm behavior over the wide pH range of operations. Also three types of fixed ionogenic acid groups are present: sulfonic (SO{sub 3}H{sup -}) groups; carboxylic (COOH{sup -}) groups, and resorcylic (OH{sup -}) groups. It is this premise that we are working under in the development of a robust isotherm model for sRF over its entire planned pH operating range. The application of prototypic isotherms for modeling ion-exchange column behavior is demonstrated in Section 3 of this report. This preliminary work served to focus the development effort on the use of a mass-action based isotherm. In Section 4 of this report, the foundational material required to develop a robust isotherm model for sRF is provided. The paths taken, and choices made, are given for the reader to better understand our current status with respect to this goal and to highlight our most recent understanding of sRF exchange equilibria. Our ultimate goal is to update the CERMOD code (Aleman and Hamm, 2007) with a robust isotherm model for sRF that spans the entire pH and concentration ranges of planned operations. The isotherm model will then be used in the VERSE-LC code to model an entire ion-exchange cycle.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Material removal and surface figure during pad polishing of fused silica

The material removal and surface figure after ceria pad polishing of fused silica glass have been measured and analyzed as a function of kinematics, loading conditions, and polishing time. Also, the friction at the workpiece/lap interface, the slope of the workpiece relative to the lap plane, and lap viscoelastic properties have been measured and correlated to material removal. The results show that the relative velocity between the workpiece & lap (determined by the kinematics) and the pressure distribution determine the spatial and temporal material removal and hence the final surface figure of the workpiece. In the case where the applied loading and relative velocity distribution over the workpiece are spatially uniform, a significant non-uniform spatial material removal from the workpiece surface is observed. This is due to a non-uniform pressure distribution resulting from: (1) a moment caused by a pivot point and interface friction forces; (2) viscoelastic relaxation of the polyurethane lap; and (3) a physical workpiece/lap interface mismatch. Both the kinematics and these contributions to the pressure distribution are quantitatively described, and then combined to form a spatial and temporal Preston model & code for material removal (called Surface Figure or SurF{copyright}). The surface figure simulations are consistent with the experiment for a wide variety of polishing conditions. This study is an important step towards deterministic full-aperture polishing, which would allow optical glass fabrication to be performed in a more repeatable, less iterative, and hence more economical manner.

42 ENGINEERING↗

Insights into Mechanisms of Screw Feeder Plugging by Heated Pine Forestry Residues Using in-situ and Correlative Microscopy

Increasing concerns about global carbon emissions due to fossil fuel use has created interest in renewable fuel alternatives, such as lignocellulosic biomass. With an estimated global biomass production probability ten-fold higher than projected need, functionalizing and scaling biomass conversion processes, like pyrolysis, is a promising component of a diverse sustainable energy program (Kan, Strezov, & Evans, 2016). Pyrolysis reactors employed in biomass conversion often encounter the known problem of screw feeder plugging, halting work and reducing efficiency of biorefineries. Although the screw feeder is not heated directly, conductive heat transfer from the fluidized bed pyrolysis reactor creates a temperature gradient, where particles experience temperatures between 22°C and 500°C from the time they enter the feeder to being emptied into the reactor (Digman, Joo, & Kim, 2009; Nieminen & Folke, 1982). The impact of unintentional heating on this highly variable feedstock may result in particle morphology modification, surface texture transformation, and the evolution of viscous compounds and may contribute to screw feeder plugging (Haas, Nimlos, & Donohoe, 2009; Ingram et al., 2008). We hypothesized that particles of various anatomical fractions (including needles, branches, bark, cambium, and whitewood) will experience dramatic changes during this heating regime, which will be characterized by decreased particle size, increased surface roughness, degradation of key structural macromolecules, and generation of viscous compounds that would result in increased particle friction and cohesion, contributing to screw feeder plugging.

biofuels↗

The Effects of Earthquakes and Fluids on the Metamorphism of the Lower Continental Crust

Rock rheology and density have first-order effects on the lithosphere's response to plate tectonic forces at plate boundaries. Changes in these rock properties are controlled by metamorphic transformation processes that are critically dependent on the presence of fluids. At the onset of a continental collision, the lower crust is in most cases dry and strong. However, if exposed to internally produced or externally supplied fluids, the thickened crust will react and be converted into a mechanically weaker lithology by fluid-driven metamorphic reactions. Fluid introduction is often associated with deep crustal earthquakes. Microstructural evidence, suggest that in strong highly stressed rocks, seismic slip may be initiated by brittle deformation and that wall-rock damage caused by dynamic ruptures plays a very important role in allowing fluids to enter into contact with dry and highly reactive lower crustal rocks. The resulting metamorphism produces weaker rocks which subsequently deform by viscous creep. Volumes of weak rocks contained in a highly stressed environment of strong rocks may experience significant excursions toward higher pressure without any associated burial. Slow and highly localized creep processes in a velocity strengthening regime may produce mylonitic shear zones along faults initially characterized by earthquake-generated frictional melting and wall rock damage. However, stress pulses from earthquakes in the shallower brittle regime may kick start new episodes of seismic slip at velocity weakening conditions. These processes indicate that the evolution of the lower crust during continental collisions is controlled by the transient interplay between brittle deformation, fluid-rock interactions, and creep flow.

58 GEOSCIENCES↗

Implementation of low-burnup swelling focused assessment case and enhancement of FIPD-BISON integration framework

This report summarizes the activities and achievements made by Argonne National Laboratory for the Nuclear Energy Advanced Modeling and Simulation (NEAMS) BISON code metallic fuel validation and verification (V&V) project in FY2023, with a focus on the capability development and assessment case development for steady state irradiation experiments. The X423 IFR experiment assessment case, which is focused on the evaluation of low burnup swelling behavior of both binary and ternary metallic fuel, has been developed. It covers 58 fuel pins with various fuel compositions and 158 sets of post-irradiation examination (PIE) data with burnup ranging from ~0.5 at.% to ~5.0 at.%, providing a powerful tool within BISON for the calibration, evaluation, verification and validation of both existing and future metallic fuel swelling models at low burnup. Meanwhile, the X447 IFR experiment assessment case established in FY2022 was enhanced to utilize the latest advanced features in BISON, such as automatic differentiation and Mortar contact models. With such enhancements, especially the Mortar mechanical contact model with friction, BISON is now capable of predicting axial fuel growth that is consistent with experimental measurements. Additionally, during the development, gaps and potential scopes were identified and explorative efforts were made, providing insight for future works.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A system for remote measurements of the wind stress over the ocean

The DISSTRESS system for remote measurements of the surface wind stress over the ocean from ships and buoys is described. It is fully digital, utilizing the inertial dissipation technique. Parallel processing allows anemometer data to be filtered in natural frequency space; that is, the filter cutoffs shift linearly with the mean wind speed of the data to be filtered. The construction of the digital Butterworth bandpass filters is presented in detail. The performance of the system is evaluated by analyzing the results from 28 days of operation during the Frontal Air-Sea Interaction Experiment. The mean wind speed is checked, the anemometer response function is established, and drag coefficients are compared to previous studies. The capability of the system is demonstrated by continuous time series of the friction velocity computed every 20 min. The conclusion is that the surface wind stress can be measured more reliably and accurately (20 percent) with this system than from anemometer wind speeds and a bulk formula.

Large, William G.↗

The effect of asymmetric vortex wake characteristics on a slender delta wing undergoing wing rock motion

An experimental investigation into the fluid mechanisms responsible for wing rock on a slender delta wing with 80 deg leading edge sweep has been conducted. Time history and flow visualization data are presented for a wide angle-of-attack range. The use of an air bearing spindle has allowed the motion of the wing to be free from bearing friction or mechanical hysteresis. A bistable static condition has been found in vortex breakdown at an angle of attack of 40 deg which causes an overshoot of the steady state rocking amplitude. Flow visualization experiments also reveal a difference in static and dynamic breakdown locations on the wing. A hysteresis loop in dynamic breakdown location similar to that seen on pitching delta wings was observed as the wing was undergoing the limit cycle oscillation.

Arena, A. S., Jr.↗

The "limiting line" in mixed subsonic and supersonic flow of compressible fluids

It is well known that the vorticity for any fluid element is constant if the fluid is non-viscous and the change of state of the fluid is isentropic. When a solid body is placed in a uniform stream, the flow far ahead of the body is irrotational. Then if the flow is further assumed to be isentropic, the vorticity will be zero over the whole filed of flow. In other words, the flow is irrotational. For such flow over a solid body, it is shown by Theodorsen that the solid body experiences no resistance. If the fluid has a small viscosity, its effect will be limited in the boundary layer over the solid body and the body will have a drag due to the skin friction. This type of essentially isentropic irrotational flow is generally observed for a streamlined body placed in a uniform stream, if the velocity of the stream is kept below the so-called "critical speed." At the critical speed or rather at a certain value of the ratio of the velocity of the undisturbed flow and the corresponding velocity of sound, shock waves appear. This phenomenon is called the "compressibility bubble." Along a shock wave, the change of state of the fluid is no longer isentropic, although still adiabatic. This results in an increase in entropy of the fluid and generally introduces vorticity in an originally irrotational flow. The increase in entropy of the fluid is, of course, the consequence of changing part of the mechanical energy into heat energy. In other words, the part of fluid affected by the shock wave has a reduced mechanical energy. Therefore, with the appearance of shock waves, the wake of the streamline body is very much widened, and the drag increases drastically. Furthermore, the accompanying change in the pressure distribution over the body changes the aerodynamic moment acting on it and in the case of an airfoil decreases the lift force. All these consequences of the breakdown of isentropic irrotational flow are generally undesirable in applied aerodynamics. Its occurrence should be delayed as much as possible by modifying the shape or contour of the body. However, such endeavor will be very much facilitated if the cause or the criterion for the breakdown can be found first.

MACH NUMBER↗

Electrical charging effects on the sliding friction of a model nano-confined ionic liquid

Recent measurements suggest the possibility to exploit ionic liquids (ILs) as smart lubricants for nano-contacts, tuning their tribological and rheological properties by charging the sliding interfaces. Following our earlier theoretical study of charging effects on nanoscale confinement and squeezout of a model IL, we present here molecular dynamics simulations of the frictional and lubrication properties of that model under charging conditions. First, we describe the case when two equally charged plates slide while being held together to a confinement distance of a few molecular layers. The shear sliding stress is found to rise strongly and discontinuously as the number of IL layers decreases stepwise. However, the shear stress shows, within each given number of layers, only a weak dependence upon the precise value of the normal load, a result in agreement with data extracted from recent experiments. We subsequently describe the case of opposite charging of the sliding plates and follow the shear stress when the charging is slowly and adiabatically reversed in the course of time, under fixed load. Despite the fixed load, the number and structure of the confined IL layers change with changing charge, and that in turn drives strong friction variations. The latter involves first of all charging-induced freezing of the IL film, followed by a discharging-induced melting, both made possible by the nanoscale confinement. Another mechanism for charging-induced frictional changes is a shift of the plane of maximum shear from mid-film to the plate-film interface, and vice versa. While these occurrences and results invariably depend upon the parameters of the model IL and upon its specific interaction with the plates, the present study helps identifying a variety of possible behavior, obtained under very simple assumptions, while connecting it to an underlying equilibrium thermodynamics picture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗