Search NASA⌕ Search

SEARCH · Search NASA

Results for “hardness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Nanoindentation Stress–Strain for Fracture Analysis and Computational Modeling for Hardness and Modulus

Stress–Strain plots based on nanoindentation load–depth curves were obtained to study phenomena like internal fracture and ductile to brittle transitions. Fracture phenomena during the indentation process were analyzed based on the stress–strain plots. A transition from ductile to brittle fracture was observed on increasing the depth or load of indenter penetration. A new approach with shape factors in the fracture studies based on radial crack branching and micro-cracking was done. Hardness and modulus plots were fitted with polynomials. The fitting parameters were varied to obtain different hardness and modulus responses.

36 MATERIALS SCIENCE↗

On the Variation of Hardness Due to Uniaxial and Equi-Biaxial Residual Surface Stresses at Elastic–Plastic Indentation

It is established long since that the material hardness is independent of residual stresses at predominantly plastic deformation close to the contact region at indentation. Recently though, it has been shown that when elastic and plastic deformations are of equal magnitude this invariance is lost. For materials such as ceramics and polymers, this will complicate residual stress determination but can also, if properly understood, provide additional important information for performing such a task. Indeed, when the residual stresses are equi-biaxial, the situation is quite well understood, but additional efforts have to be made to understand the mechanical behavior in other loading states. Presently therefore, the variation of hardness, due to residual stresses, is examined at a uniaxial stress state. Correlation with global indentation quantities is analyzed, discussed and compared to corresponding equi-biaxial results. Cone indentation of elastic–perfectly plastic materials is considered.

36 MATERIALS SCIENCE↗

Extreme hardness at high temperature with a lightweight additively manufactured multi-principal element superalloy

Materials are needed that can tolerate increasingly harsh environments, especially ones that retain high strength at extreme temperatures. Higher melting temperature alloys, like those consisting primarily of refractory elements, can greatly increase the efficiency of turbomachinery used in grid electricity production worldwide. Existing alloys, including Ni- and Co-based superalloys, used in components like turbine blades, bearings, and seals, remain a performance limiting factor due to their propensity, despite extensive optimization efforts, for softening and diffusion-driven elongation at temperatures often well above half their melting point. To address this critical materials challenge, we present results from integrating additive manufacturing and alloy design to guide significant improvements in performance via traditionally difficult-to-manufacture refractory alloys. We present an example of a multi-principal element alloy (MPEA), consisting of five refractory elements and aluminum, that exhibited high hardness and specific strength surpassing other known alloys, including superalloys. The alloy shows negligible softening up to 800°C and consists of four compositionally distinct phases, in distinction to previous work on MPEAs. Density functional theory calculations reveal a thermodynamic explanation for the observed temperature-independent hardness and favorability for the formation of this multiplicity of phases.

36 MATERIALS SCIENCE↗

Damage progression and failure of SiC/SiC composite tubes under hard-contact radial expansion

The response of silicon carbide (SiC) fiber-reinforced SiC matrix (SiC/SiC) composite cladding to mechanical interaction with fissile fuel is a knowledge gap that must be overcome to design and assess SiC-based cladding systems for advanced nuclear applications. This study developed the relevant mechanical testing capability and identified the failure behavior and the critical microstructural features and processing defects. Sections of SiC composite tube were subjected to a modified expansion-due-to-compression (EDC) test in an X-ray computed tomography microscope: a polyurethane plug pressed surrogate Al 2 O 3 into the inner walls of the SiC/SiC composite tubes to achieve hard contact. A pure EDC test with just a polyurethane plug was also performed as a reference. Through the use of displacement fields, digital volume correlation revealed inhomogeneous deformation fields in the tubes, even for pure EDC, which was related to the inherent defects in the structure. Deep learning–aided segmentation and systematic data analysis revealed that the presence of inhomogeneous deformation applied by the hard contact was exaggerated by the presence of inner surface imperfections left behind from the matrix densification process. In conclusion, the findings provide insights into the applications, highlighting the necessity for improvements in inner surface roughness and the incorporation of localized contacts in pellet–cladding mechanical interaction computational models.

Composites↗

Design and engineering challenges of a multi-energy hard x-ray camera for long-pulse profile measurements at WEST tokamak

The WEST tokamak has recently been prepared for long pulse operation with a water-cooled full first wall. Heating is provided by radiofrequency systems, including Lower Hybrid Current Drive (LHCD). The Princeton Plasma Physics Laboratory has developed a multi-energy hard x-ray camera for profile measurements at WEST. The camera is based on a new generation of 2D pixel array detectors that allow the energy threshold to be independently set for each pixel. The diagnostic will provide spatial, temporal and energy resolved measurements of the hard x-ray emission from the full plasma cross-section, investigating several physical quantities such as the electron temperature from continuum emission, the fast electron tail density produced by radiofrequency current drive and runaway electrons, as well as characteristic tungsten x-rays due to beam-target emission at the edge. Overall, this work describes the engineering challenges that the WEST long pulse scenario poses for this diagnostic and how the design addresses and solves them. Vacuum, thermal stress and heat transfer calculations are presented and discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Heat-treated glassy carbon under pressure exhibiting superior hardness, strength and elasticity

Glassy carbon (GC) is a type of non-graphitizing disordered carbon material at ambient pressure and high temperatures, which has been widely used due to its excellent mechanical properties. Here we report the changes in the microstructure and mechanical properties of GC treated at high pressures (up to 5 GPa) and high temperatures. The formation of intermediate sp 2 –sp 3 phases is identified at moderate treatment temperatures before the complete graphitization of GC, by analyzing synchrotron X-ray diffraction, Raman spectra, and transmission electron microscopy images. The intermediate metastable carbon materials exhibit superior mechanical properties with hardness reaching up to 10 GPa and compressive strength reaching as high as 2.5 GPa, nearly doubling those of raw GC, and improving elasticity and thermal stability. The synthesis pressure used in this study can be achieved in the industry on a commercial scale, enabling the scalable synthesis of this type of strong, hard, and elastic carbon materials.

36 MATERIALS SCIENCE↗

A mechanistic model for depth-dependent hardness of ion irradiated metals

A mechanistic model was developed for modeling the depth-dependent hardness in ion irradiated metallic materials. The model is capable of capturing the indentation size effect, ion irradiation induced damage gradient effect, and effect of unirradiated region acting as a soft substrate. A procedure was developed and described in detail to parametrize the model based on experimentally obtained hardness vs. indentation depth curves. Very good agreement was observed between our model predictions and experimental data of several different stainless steels subjected to various ion irradiation conditions. Additionally, two hardening mechanisms are revealed in the new model. One is the well-known indentation size effect arising from the creation of geometrically necessary dislocations as the indenter pierces into the materials. The other is the irradiation hardening due to the presence of irradiation-induced defects. As a function of indentation depth h, the hardening due to indentation size effect is described by $\bar{h}^*/h$, while the hardening due to irradiation first follows a power law form $ph^n$, then changes to Z/h - Q/h 3 , where $\bar{h}^*$, P, n, Z and Q > 0 are constants. This transition occurs at the indentation depth when the plastic zone reaches the end of the irradiated layer.

36 MATERIALS SCIENCE↗

Microstructural evolutions, phase transformations and hard magnetic properties in polycrystalline Ce–Co–Fe–Cu alloys

This work focuses on systematic studies of Ce–Co based 1:5 permanent magnet alloys of CeCo 4.4-x Fe x Cu 0.6 and CeCo 3.9-x Fe x Cu 1.2 (x = 0, 0.3, 0.6, 0.9, 1.2, 1.8) by varying Co:Fe. The overarching aim of this manuscript is to elucidate the hard-magnetic properties through a better understanding of phase formation by the structural, microstructural, and magnetic properties in these materials. Improved mutual solubility of Fe in the 1:5 phase has been observed with an extended homogeneity range by Cu substitution. For both composition series, Fe contents of x ≤ 0.6 show a homogeneous microstructure with a single 1:5 phase and good magnetic properties. The composition region 0.6 < x ≤ 0.9 appears to be near the boundary of solubility and evolution of other phases. At x = 1.8, it is found that the homogeneous 1:5 phase and magnetic hardness deteriorated due to the evolution of secondary phases such as 2:17, 2:7, and Fe–Co. Furthermore, the addition of Fe improved both the magnetization and Curie temperature via increased effective exchange interactions, while an increase in Cu content enhanced coercivity.

33 ADVANCED PROPULSION SYSTEMS↗

Decoupling the effects of substrate hardness and roughness upon particle adhesion in cold spray

There are two stages of particle adhesion relevant to cold spray: adhesion of the first layer to the substrate, followed by inter-particle adhesion during subsequent deposition. In this work we study the second of these, in which particles strike a previously-deposited layer that is roughened and hardened by prior particle impacts. Specifically, we decouple the effects of surface roughness and hardness on particle adhesion for copper-on-copper impacts. We measure changes to the critical velocity, V cr , in single particle impacts produced by the Laser Induced Particle Impact Test on several surfaces including a cold sprayed surface and a polished version of that surface. We find that increases in both substrate roughness and hardness suppress particle adhesion to higher velocities, indeed in rather equal proportion by ∼10–15% each. This suggests that there is a higher V cr associated with coating build-up (particle-particle bonding) that is overall ∼30% higher than V cr for particle-substrate adhesion.

36 MATERIALS SCIENCE↗

Bonded multilayer Laue Lens for focusing hard x-rays.

We have fabricated partial Multilayer Laue Lens (MLL) linear zone plate structures with thousands of alternating WSi{sub 2} and Si layers and various outermost zone widths according to the Fresnel zone plate formula. Using partial MLL structures, we were able to focus hard X-rays to line foci with a width of 30 nm and below. Here, we describe challenges and approaches used to bond these multilayers to achieve line and point focusing. Bonding was done by coating two multilayers with AuSn and heating in a vacuum oven at 280-300 C. X-ray reflectivity measurements confirmed that there was no change in the multilayers after heating to 350 C. A bonded MLL was polished to a 5-25 {micro}m wedge without cracking. SEM image analyses found well-positioned multilayers after bonding. These results demonstrate the feasibility of a bonded full MLL for focusing hard X-rays.

36 MATERIALS SCIENCE↗

An investigation of hard-disk drive circularity accounting for socio-technical dynamics and data uncertainty

The installed data storage capacity in the U.S. will reach 2.2 Zettabytes by 2025, generating about 50 million units of end-of-life (EOL) hard-disk drives (HDDs) per year. Due to data security concerns, most EOL HDDs are currently shredded (even when still functioning), representing an economic loss. Moreover, raw material extraction linked to the increased demand for storage causes environmental impacts. Besides mitigating the threat posed by sudden restrictions of raw materials, the circular economy (CE) offers to maximize value retention in the economy and reduce the environmental impacts of human activities. Common CE strategies are reusing and recycling products. However, the reuse of hard disk drives is currently burdened by the lack of trust HDD end-users have toward other non-physical means of data removal than shredding. Here, an agent-based modeling (ABM) approach is proposed to explore how techno-economic and social factors affect end-users' decisions to adopt EOL management practices other than shredding. The proposed method also accounts for data uncertainty by applying a semi-quantitative approach. Results demonstrate how increased green procurement and more robust standards could spur end-users' trust toward data-wiping technologies. Even when accounting for uncertainty, HDDs' reuse brings better environmental and economic benefits than HDD shredding followed by material recovery. The semi-quantitative approach proposed in this study could be more universally applied in future ABM, especially given the often-stochastic nature of such models. The developed ABM is also the first to represent several HDD industry stakeholders and demonstrate how the HDD shredding lock-in situation could be resolved.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

On the origins of hardness of Cu–TiN nanolayered composites

We investigated the mechanical response of physical vapor deposited Cu–TiN nanolayered composites of varying layer thicknesses from 5 nm to 200 nm. Both the Cu and TiN layers were found to consist of single phase nanometer sized grains. The grain sizes in the Cu and TiN layers, measured using transmission electron microscopy and X-ray diffraction, were found to be comparable to or smaller than their respective layer thicknesses. Indentation hardness testing revealed that the hardness of such nanolayered composites exhibits a weak dependence on the layer thickness but is more correlated to their grain size.

36 MATERIALS SCIENCE↗

Material hardness at strain rates beyond 10 6 s –1 via high velocity microparticle impact indentation

Despite advances in mechanical testing at small scales and testing at high strain rates, studies of mechanical behavior of materials remain largely qualitative in the regimes where these two conditions overlap. In this work, we present an approach based on microparticle impact indentation to determine material hardness at micron scales and at high strain rates. We employ laser ablation to impact ceramic alumina microparticles (as indenter) onto two model materials, namely copper and iron. We use real time measurements of impact and rebound velocities together with post- impact measurements of indentation volume to determine material hardness at strain rates beyond 10 6 s –1 .

36 MATERIALS SCIENCE↗

In vitro expression of hard metal dust (WC-Co) - responsive genes in human peripheral blood mononucleated cells

Hard metals consist of tungsten carbide (WC) and metallic cobalt (Co) particles and are important industrial materials produced for their extreme hardness and high wear resistance properties. While occupational exposure to metallic Co alone is apparently not associated with an increased risk of cancer, the WC-Co particle mixture was shown to be carcinogenic in exposed workers. The in vitro mutagenic/apoptogenic potential of WC-Co in human peripheral blood mononucleated cells was previously demonstrated by us. This study aimed at obtaining a broader view of the pathways responsible for WC-Co induced carcinogenicity, and in particular genotoxicity and apoptosis. We analyzed the profile of gene expression induced in vitro by WC-Co versus control (24 h treatment) in human PBMC and monocytes using microarrays. The most significantly up-regulated pathways for WC-Co treated PBMC were apoptosis and stress/defense response; the most down-regulated was immune response. For WC-Co treated monocytes the most significantly up- and down-regulated pathways were nucleosome/chromatin assembly and immune response respectively. Quantitative RT-PCR data for a selection of the most strongly modulated genes (HMOX1, HSPA1A, HSPA1L, BNIP3, BNIP3L, ADORA2B, MT3, PLA2G7, TNFAIP6), and some additionally chosen apoptosis related genes (BCL2, BAX, FAS, FASL, TNF{alpha}), confirmed the microarray data after WC-Co exposure and demonstrated limited differences between the Co-containing compounds. Overall, this study provides the first analysis of gene expression induced by the WC-Co mixture showing a large profile of gene modulation and giving a preliminary indication for a hypoxia mimicking environment induced by WC-Co exposure.

60 APPLIED LIFE SCIENCES↗

Modulation of hard x-ray beam profiles by Borrmann pyramid

Spatial modulation of hard x-ray beam profiles is reported, using the 'Borrmann pyramid' formed in dual Bragg diffraction of a single crystal, where a small angular change of the incident beam is magnified to span the entire pyramid base. As an attempt, it is demonstrated using hard x rays by (1) the linear shift of a micrometer sized mask; (2) the partial blockade of a two micron beam; and (3) the millimeter shadow of a nanoscale gold strip, which shows the potential application of Borrmann pyramids in the form of an enlarged x-ray image.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

A hard x-ray nanoprobe for scanning and projection nanotomography

To fabricate and qualify nanodevices, characterization tools must be developed to provide a large panel of information over spatial scales spanning from the millimeter down to the nanometer. Synchrotron x-ray-based tomography techniques are getting increasing interest since they can provide fully three-dimensional (3D) images of morphology, elemental distribution, and crystallinity of a sample. Here we show that by combining suitable scanning schemes together with high brilliance x-ray nanobeams, such multispectral 3D volumes can be obtained during a single analysis in a very efficient and nondestructive way. We also show that, unlike other techniques, hard x-ray nanotomography allows reconstructing the elemental distribution over a wide range of atomic number and offers truly depth resolution capabilities. The sensitivity, 3D resolution, and complementarity of our approach make hard x-ray nanotomography an essential characterization tool for a large panel of scientific domains.

36 MATERIALS SCIENCE↗

Multipomeron Cuts and Hard Processes on Nuclei

With nuclear targets comes a new scale into the pQCD description of hard processes - the saturation scale. In the saturation regime, the familiar linear k{sub perpendicular}-factorization breaks down and must be replaced by a nonlinear k{sub perpendicular}-factorization, which accounts for absorptive and multiple scattering corrections to the hard process. Predictions for partial cross sections corresponding to a fixed number of cut Pomerons (the topological cross sections) can be obtained in a surprisingly straightforward manner. We discuss some applications to deep inelastic scattering.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

The Hard X-ray Sky: Recent Observational Progress

The last fifty years have witnessed the birth, development, and maturation to full potential of hard X-ray astrophysics. The primary force driving the history of the field has been the development of space-based instrumentation optimized for getting the maximum science out of observations of high-energy photons from astrophysical sources. Hard X-ray telescopes are leading research in areas such as galactic diffuse emission, galactic transients, and active galactic nuclei.

79 ASTRONOMY AND ASTROPHYSICS↗