Search NASA⌕ Search

SEARCH · Search NASA

Results for “high modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Non-linear numerical analysis of the Iosipescu specimen for composite materials

A nonlinear elastic finite element analysis is presented of the Iosipescu shear specimen tested in the modified Wyoming fixture for unidirectional graphite/epoxy composites. It is shown that the nonlinear effects due to specimen-to-fixture contact interactions and specimen geometry on the overall shear response are negligible. It is proposed that the tangential shear modulus should be used to characterize the shear resistance of composite materials with highly nonlinear shear response. The correction factors, which are needed to compensate for the nonuniformity of the shear stress or strain distribution in the specimen test section for shear modulus measurement, have to be defined carefully. Strain contours in the nonlinear response ranges are presented and the initiation of failure in the notch regions is investigated.

Ho, Henjen↗

Stiff and Transparent Multilayer Thin Films Prepared Through Hydrogen-Bonding Layer-by-Layer Assembly of Graphene and Polymer [Super Stiff and Highly Transparent Multilayer Thin Films Prepared through Hydrogen-Bonding Layer-by-Layer Assembly of Graphene and Polymer]

Due to their exceptional orientation of 2D nanofillers, layer–by–layer (LbL) assembled polymer/graphene oxide thin films exhibit unmatched mechanical performance relative to any conventionally produced counterparts with similar composition. Unprecedented mechanical property improvement, by replacing graphene oxide with pristine graphene, is demonstrated in this work. Polyvinylpyrrolidone–stabilized graphene platelets are alternately deposited with poly(acrylic acid) using hydrogen bonding assisted LbL assembly. Transmission electron microscopy imaging and the Halpin–Tsai model are used to demonstrate, for the first time, that intact graphene can be processed from water to generate polymer nanocomposite thin films with simultaneous parallel–alignment, high packing density, and exfoliation. A multilayer thin film with only 3.9 vol% of highly exfoliated, and structurally intact graphene, increases the elastic modulus (E) of a polymer multilayer thin film by 322% (from 1.41 to 4.81 GPa), while maintaining visible light transmittance of ≈90%. This is one of the greatest improvements in elastic modulus ever reported for a graphene–filled polymer nanocomposite with a glassy (E > 1 GPa) matrix. In conclusion, the technique described here provides a powerful new tool to improve nanocomposite properties (mechanical, gas transport, etc.) that can be universally applied to a variety of polymer matrices and 2D nanoplatelets.

36 MATERIALS SCIENCE↗

Vanadium oxide nanotubes VOx-NTs: Hydrothermal synthesis, characterization, electrical study and dielectric properties

Vanadium oxide nanotubes (VOx-NTs) have been synthesized via one-step hydrothermal treatment. The compounds were analyzed through X-ray powder diffraction; scanning electron microscope, UV–Visible spectroscopy, X-ray photoelectron spectroscopy (XPS) and complex impedance spectroscopy. The electrical and dielectric properties dependence on temperature (302–523 K) and on frequency (5 Hz to 13 MHz) of VOx-NTs have been reported. The complex impedance plots exhibits the presence of grain and grain boundaries. Dielectric data were analyzed using complex permittivity and complex electrical modulus for the sample at various temperatures. The presence of non-Debye type of relaxation has been confirmed by the complex modulus analysis. AC conductivity exhibits two conduction mechanisms: at high temperature, a translational motion with a sudden hopping and at low temperature, a localized hopping with a small hopping or reorientational motion. DC conductivity indicated, negative temperature coefficient of resistance (NTCR) type behavior. - Graphical abstract: The imaginary part of dielectric constant decreases with the increase in frequency at all temperatures and the values of ε´´ exhibit considerable frequency dispersion in the lower frequency range . Highlights: •Vanadium oxide nanotubes (VOx-NTs) were synthesized. •Non-debye type of relaxation has been confirmed. •AC conductivity exhibits two conduction mechanisms. •DC conductivity indicated negative temperature coefficient of resistance type behavior.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microstructure and mechanical properties of Ti-35Nb-6Ta alloy after thermomechanical treatment

The influence of thermo-mechanical treatment on microstructure and mechanical properties of T-35Nb-6Ta has been studied. The thermo-mechanical treatment was chosen to correspond to the production of wire with suitable mechanical properties for dental implants. After casting the alloy was hot forged (700-900 Degree-Sign C), solution treated (850 Degree-Sign C/30 min, water quenched) and cold swaged (reductions up to 91%). The annealing (700 Degree-Sign C/3 h/furnace) or aging (450 Degree-Sign C/8 h/furnace) was used as final heat treatment. The microstructure was studied by using light microscopy, scanning electron microscopy, transmission electron microscopy and XRD analysis. Cold swaging introduces microstructure consisting of highly deformed {beta}-phase grains with dislocation tangles and twins, which ensures high tensile strength about 820 MPa, low Young's modulus ({approx} 50 GPa) and good ductility {approx} 10%. Subsequent aging increases tensile strength (1000 MPa) as well as Young's modulus (75 GPa) without diminishing ductility. Annealing at 700 Degree-Sign C slightly decreases tensile strength (730 MPa) and increases the ductility and Young's modulus (17% and 62 GPa respectively). The mechanical properties attained recommend the thermo-mechanical treatment for production of wires for dental implants. - Highlights: Black-Right-Pointing-Pointer Ti35Nb6Ta alloy prepared via arc melting. Black-Right-Pointing-Pointer Thermo mechanical treatment. Black-Right-Pointing-Pointer Microstructural changes. Black-Right-Pointing-Pointer Mechanical properties.

36 MATERIALS SCIENCE↗

Preparation and mechanical properties of silicon oxycarbide fibers from electrospinning/sol-gel process

Graphical abstract: Ceramic fibers, silicon oxycarbide (SiOC) fibers were demonstrated and showed higher mechanical properties from electrospinning/sol-gel process at 1000 Degree-Sign C. Highlights: Black-Right-Pointing-Pointer SiOC fibers with low cost are promising to substitute the non-oxide fibers. Black-Right-Pointing-Pointer Successful preparation of SiOC fibers by electrospinning/sol-gel process. Black-Right-Pointing-Pointer Confirmation of the designed product using material characterization methods. Black-Right-Pointing-Pointer The SiOC fibers prepared at 1000 Degree-Sign C possess higher strength (967 MPa). -- Abstract: Silicon oxycarbide (SiOC) fibers were produced through the electrospinning of the solution containing vinyltrimethoxysilane and tetraethoxysilane in the course of sol-gel reaction with pyrolysis to ceramic. The effect of the amount of spinning agent Polyvinylpyrrolidone (PVP) on the dope spinnability was investigated. At a mass ratio of PVP/alkoxides = 0.05, the spinning sol exhibited an optimal spinnable time of 50 min and generated a large quantity of fibers. Electrospun fibers were characterized by Fourier transform infrared spectroscopy (FTIR), thermo gravimetric analysis-differential scanning calorimetry (TGA-DSC), scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The SEM results revealed that the SiOC fibers had a smooth surface and dense cross-section, free of residue pores and cracks. The XPS results gave high content of SiC (13.99%) in SiOC fibers. The SiOC fibers prepared at 1000 Degree-Sign C had a high tensile strength of 967 MPa and Young's modulus of 58 GPa.

36 MATERIALS SCIENCE↗

Synthesis and Characterization of Itaconic Anhydride and Stearyl Methacrylate Copolymers

The free-radical copolymerization and the properties of comb-like copolymers derived from renewable resources, itaconic anhydride (ITA) and stearyl methacrylate (SM), are described. The ITA-SM copolymers were nearly random with a slight alternating tendency. The copolymers exhibited a nanophase-separated morphology, with the stearate side-chains forming a bilayer, semi-crystalline structure. The melting point (Tm) of the side-chains and the crystallinity decreased with increasing ITA concentration. The crystalline side-chains suppressed molecular motion of the main chain, so that a glass transition temperature (Tg) was not resolved unless the ITA concentration was sufficiently high so that Tg > Tm. The softening point and modulus of the copolymers increased with the increasing ITA concentration, but the thermal stability decreased.

36 MATERIALS SCIENCE↗

Altered post-fracture systemic bone loss in a mouse model of osteocyte dysfunction

Femur fracture leads to loss of bone at uninjured skeletal sites, which may increase risk of subsequent fracture. Osteocytes, the most abundant bone cells, can directly resorb bone matrix and regulate osteoclast and osteoblast activity, but their role in systemic bone loss after fracture remains poorly understood. In this study we used a transgenic (TG+) mouse model that overexpresses human B-cell lymphoma 2 (BCL-2) in osteoblasts and osteocytes. This causes enhanced osteoblast proliferation, followed by disruption in lacunar-canalicular connectivity and massive osteocyte death by 10 wk of age. We hypothesized that reduced viable osteocyte density would decrease the magnitude of systemic bone loss after femur fracture, reduce perilacunar remodeling, and alter callus formation. Bone remodeling was assessed using serum biomarkers of bone formation and resorption at 5 d post-fracture. We used micro-computed tomography, high resolution x-ray microscopy, mechanical testing, and Raman spectroscopy to quantify the magnitude of systemic bone loss, as well as changes in osteocyte lacunar volume, bone strength, and bone composition 2 wk post-fracture. Fracture was associated with a reduction in circulating markers of bone resorption in non-transgenic (TG-) animals. TG+ mice exhibited high bone mass in the limbs, greater cortical elastic modulus and reduced post-yield displacement. After fracture, TG+ mice lost less trabecular bone than TG- mice, but conversely TG+ mice exhibited trends toward a lower yield point and reduced femoral cortical thickness after fracture, though these were not statistically significant. Lacunar density was greater in TG+ mice, but fracture did not alter lacunar volume in TG+ or TG- mice. These findings suggest that osteocytes potentially play a significant role in the post-traumatic systemic response to fracture, though the effects differ between trabecular and cortical bone.

60 APPLIED LIFE SCIENCES↗

Anorthite - Thermal equation of state to high pressures

New shock-wave data are presented for anorthite from which a full high-temperature, high-pressure equation of state is derived. Whereas anorthite has relatively low values of thermal expansion and Grueneisen parameter at zero pressure, it is found that these attain relatively high values in the high density state corresponding to the high-pressure phase Hugoniot but decrease upon compression as expected. It is noted that higher order anharmonic contributions decrease more rapidly with pressure and that the thermal expansion therefore saturates to a high temperature value at pressures above about 100 GPa. Reduction of the Hugoniot data permits shock temperatures to be calculated; it also yields a principal adiabat for the high pressure branch of the Hugoniot. The initial bulk modulus of this adiabat is essentially identical to that of anorthite, whereas the initial density is about 3.40 Mg/cu m.

Jeanloz, R.↗

Interface effects in interlaminar fracture of thermoplastic composites

Mode I interlaminar fracture toughness was determined on a series of unidirectional poly(phenylene oxide)/carbon fiber composites using the double cantilever beam test. Initial toughness for growth of a delamination from an insert depends on fiber type, and ranges from 190 to 440 J/sq m, with intermediate modulus fibers tending to give lower values than high-strain fibers. Low toughness values are attributed to poor fiber-matrix adhesion. As a delamination progress down the beam, fiber bridging increases the apparent toughness by up to a factor of 7, depending on the fiber.

Hinkley, J. A.↗

METCAN updates for high temperature composite behavior: Simulation/verification

The continued verification (comparisons with experimental data) of the METCAN (Metal Matrix Composite Analyzer) computer code is updated. Verification includes comparisons at room and high temperatures for two composites, SiC/Ti-15-3 and SiC/Ti-6-4. Specifically, verification of the SiC/Ti-15-3 composite includes comparisons of strength, modulus, and Poisson's ratio as well as stress-strain curves for four laminates at room temperature. High temperature verification includes comparisons of strength and stress-strain curves for two laminates. Verification of SiC/Ti-6-4 is for a transverse room temperature stress-strain curve and comparisons for transverse strength at three temperatures. Results of the verification indicates that METCAN can be used with confidence to simulate the high temperature nonlinear behavior of metal matrix composites.

Lee, H.-J.↗

METCAN updates for high temperature composite behavior - Simulation/verification

The continued verification (comparisons with experimental data) of the METCAN (Metal Matrix Composite Analyzer) computer code is updated. Verification includes comparisons at room and high temperatures for two composites, SiC/Ti-15-3 and SiC/Ti-6-4. Specifically, verification of the SiC/Ti-15-3 composite includes comparisons of strength, modulus, and Poisson's ratio as well as stress-strain curves for four laminates at room temperatures. High temperature verification includes comparisons of strength and stress-strain curves for two laminates. Verification of SiC/Ti-6-4 is for a transverse room temperature stress-strain curve and comparisons for transverse strength at three temperatures. Results of the verification indicates that METCAN can be used with confidence to simulate the high temperature nonlinear behavior of metal matrix composites.

Lee, H.-J.↗

Task-Specific Phosphonium Iongels by Fast UV-Photopolymerization for Solid-State Sodium Metal Batteries

Sodium metal batteries are an emerging technology that shows promise in terms of materials availability with respect to lithium batteries. Solid electrolytes are needed to tackle the safety issues related to sodium metal. In this work, a simple method to prepare a mechanically robust and efficient soft solid electrolyte for sodium batteries is demonstrated. A task-specific iongel electrolyte was prepared by combining in a simple process the excellent performance of sodium metal electrodes of an ionic liquid electrolyte and the mechanical properties of polymers. The iongel was synthesized by fast (<1 min) UV photopolymerization of poly(ethylene glycol) diacrylate (PEGDA) in the presence of a saturated 42%mol solution of sodium bis(fluorosulfonyl)imide (NaFSI) in trimethyl iso-butyl phosphonium bis(fluorosulfonyl)imide (P111i4FSI). The resulting soft solid electrolytes showed high ionic conductivity at room temperature (≥10 -3 S cm -1 ) and tunable storage modulus (10 4 –10 7 Pa). Iongel with the best ionic conductivity and good mechanical properties (Iongel10) showed excellent battery performance: Na/iongel/NaFePO 4 full cells delivered a high specific capacity of 140 mAh g -1 at 0.1 C and 120 mAh g -1 at 1 C with good capacity retention after 30 cycles.

25 ENERGY STORAGE↗

Negative Thermal Expansion, Response to Pressure and Phase Transitions in CaTiF 6

Strong volume negative thermal expansion over a wide temperature range typically only occurs in ReO 3 -type fluorides that retain an ideal cubic structure to very low temperatures, such as ScF 3 , CaZrF 6 , CaHfF 6 , and CaNbF 6 . In this work, CaTiF 6 was examined in an effort to expand this small family of materials. However, it undergoes a cubic ($Fm\overline{3}m$) to rhombohedral ($R\overline3$) transition on cooling to ~120 K, with a minimum volume coefficient of thermal expansion (CTE) close to –42 ppm K –1 at 180 K and a CTE of about –32 ppm K –1 at room temperature. On compression at ambient temperature, the material remains cubic to ~0.25 GPa with K 0 = 29(1) GPa and K' 0 = –50(5). Cubic CaTiF 6 is elastically softer and shows more pronounced pressure induced softening, than both CaZrF 6 and CaNbF 6 . In sharp contrast to both CaZrF 6 and CaNbF 6 , CaTiF 6 undergoes a first-order pressure induced octahedral tilting transition to a rhombohedral phase ($R\overline3$) on compression above 0.25 GPa, which is closely related to that seen in ScF 3 . Just above the transition pressure, this phase is elastically very soft with a bulk modulus of only ~4 GPa as octahedral tilting associated with a reduction in the Ca–F–Ti angles provides a low energy pathway for volume reduction. This volume reduction mechanism leads to highly anisotropic elastic properties, with the rhombohedral phase displaying both a low bulk modulus and negative linear compressibility parallel to the crystallographic c -axis for pressures below ~2.5 GPa. At ~3 GPa, a further phase transition to a poorly ordered phase occurs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A shock-induced phase change in iron-silicate garnet.

Hugoniot measurements on iron-silicate garnet demonstrate that above a shock pressure of about 205 kbar transition to a high-pressure phase(s), having an apparent zero-pressure density and bulk modulus of 4.44 g/cu cm and 3.3 Mbar, occurs. Crystal chemical systematics and Debye-Scherrer X-ray patterns of a recovered phase(s), which may be the shock-induced high-pressure form, suggest possible formation of a phase with a density of 4.48/cu cm. Occurrence of such a polymorph of garnet in the mantle would give rise to an increase in density and seismic velocity below 600 km in the earth.

Ahrens, T. J.↗

Tensile Modeling PVC Gels for Electrohydraulic Actuators

Polyvinyl chloride (PVC)-dibutyl adipate (DBA) gels are a fascinating dielectric elastomer actuator showing promise in soft robotics. When actuated with high voltages, the gel deforms towards the anode. A recent application of PVC gels in electrohydraulic actuators motivates elastic and hyperelastic constitutive relationships for tensile loading modes. PVC gels with plasticizer-to-polymer weight ratios of 2:1, 4:1, 6:1, and 8:1 w/w were evaluated. PVC gels exhibit a linear elastic region up to 25% strain. The elastic modulus decreased with increasing plasticizer content from 288.8 kPa, 56.1 kPa, 24.7 kPa, to 11 kPa. Poisson’s ratio also decreased with increasing plasticizer content from 0.42, 0.43, 0.39, to 0.35. We suggest that the decrease in polymer concentration facilitates a weakly interconnected polymer network susceptible to chain slippage that hinders the network response, thus lowering Poisson’s ratio. Our work suggests that PVC gels can be treated as isotropic and incompressible for large strains and hyperelastic modeling; however, highly plasticized gels tend to act less incompressible at small strains. The power scaling law between the elastic modulus and plasticizer weight ratio showed high agreement, making the elastic modulus deterministic for any plasticizer content. The Neo–Hookean, Mooney–Rivlin, Yeoh, Gent, Ogden, and extended tube hyperelastic constitutive models are investigated. The Yeoh model shows the highest feasibility when evaluated up to 3.5 stretch, showing a maximum normalized root-mean-square-error of 6.85%. Together, these findings establish a constitutive basis for PVC-DBA gels, incorporating small strain elasticity, large strain non-linear behavior, and network analysis while providing suggestive insight into the network structure required for accurately modeling the EPIC.

Polymer Science↗

A metallic peanut-shaped carbon nanotube and its potential for CO 2 capture

One of the greatest challenges in greenhouse gas reduction is to develop low-cost materials capable of efficient CO 2 capture. Carbon, due to its flexible bonding characteristics, numerous allotropic forms, and lightweight, is an attractive material for such investigation. Inspired by the experimental synthesis of C 50 Cl 10 in milligram quantities and recent works on peanut-shaped carbon nanotubes (PSNT), using state-of-the-art first-principles theory and molecular dynamics simulation, here we have discovered a new form of C 50 fullerene-based PSNT, α-PSNT. which is not only dynamically and thermally stable, but also energetically more stable than previously identified PSNTs composed of C 50 cages, and can withstand temperatures to 1000 K. Due to its unique atomic configuration, α-PSNT exhibits interesting physical properties including a high heat capacity, ultra-soft mechanical property with Young's modulus being a quarter of single-walled carbon nanotube (SWNT), and chirality independent metallicity. A systematical study of the adsorption properties reveals that both pristine and N-doped α-PSNTs have better CO 2 adsorption properties than SWNTs. The underline mechanism is that the intrinsic metallicity improves its ability to capture CO 2 as well as other gases because of the high density of electronic states at the Fermi level.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Ultrahigh Elastic Strain Energy Storage in Metal-Oxide-Infiltrated Patterned Hybrid Polymer Nanocomposites

Modulus of resilience, the measure of a material’s capacity to store and release elastic strain energy, is critical for realizing advanced mechanical actuation technologies in micro/nanoelectromechanical systems. In general, engineering the modulus of resilience is difficult because it requires asymmetrically increasing yield strength and Young’s modulus against their mutual scaling behavior. This task becomes further challenging if it needs to be carried out at the nanometer scale. Here, we demonstrate organic–inorganic hybrid composite nanopillars with one of the highest modulus of resilience per density by utilizing vapor-phase aluminum oxide infiltration in lithographically patterned negative photoresist SU-8. In situ nanomechanical measurements reveal a metal-like high yield strength (~500 MPa) with an unusually low, foam-like Young’s modulus (~7 GPa), a unique pairing that yields ultrahigh modulus of resilience, reaching up to ~24 MJ/m 3 as well as exceptional modulus of resilience per density of ~13.4 kJ/kg, surpassing those of most engineering materials. The hybrid polymer nanocomposite features lightweight, ultrahigh tunable modulus of resilience and versatile nanoscale lithographic patternability with potential for application as nanomechanical components which require ultrahigh mechanical resilience and strength.

36 MATERIALS SCIENCE↗