Search NASA⌕ Search

SEARCH · Search NASA

Results for “intermittency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Measurements in the mixing region of a turbulent jet in a coflowing airstream

The mixing region of a turbulent jet is an important example of an intermittent turbulent shear flow. There are a great deal of interest in this region because of interest in jet noise and STOL aircraft which use upper surface blowing or externally blown flap configurations to increase lift. A detailed study of the one point statistical properties of a smoke laden jet was made using a combination of a laser velocimeter and a light scattering system. The jet, with a 14 to 1 contraction, was placed inside a wind tunnel where the ratio of the jet exit velocity to free stream was 5.1 to 1. All measurements are made for a jet Reynolds number of 22,600. Among the quantities measured are mean axial and radial velocities, axial and radial intensities, power spectra, mean smoke concentration, concentration intensities, concentration spectra, intermittencies and velocity-concentration correlations. The results are compared with hot-wire data where available.

Morton, J. B.↗

An experimental investigation of a three-dimensional wall jet

An experimental investigation of the effects of a curved and flat wall surface on the flow development of an axisymmetric jet exhausting into a moving airstream has been made. Of primary concern was the comparison of the one-point statistical properties of the unconfined jet to the quantities measured in the flows over a flat plate and a curved wall surface. Quantities measured in this investigation included mean velocities in all three directions, turbulent intensities, autocorrelations, power spectral densities, and intermittencies. The investigation was confined to the near field of the turbulent jet. The curved wall (flap) was found to have a very large effect on both the mean velocity and the turbulent velocity components of the flowfield. The potential core region of the jet was found to break up most rapidly for the flow over the flap. A laser-Doppler velocimeter, using a phase locked-loop processor, was used to make the desired velocity field measurements. To determine the intermittency profiles, a laser light scattering technique was employed.

Catalano, G. D.↗

Macroscopic study of time unsteady noise of an aircraft engine during static tests

Static tests of aircraft engines can exhibit greater than 10 dB random unsteadiness of tone noise levels because flow disturbances that prevail near test site facilities are ingested. Presumably such changes are related to installation and test site features. This paper presents some properties of unsteady noise observed at a NASA-Lewis facility during tests of a Lycoming YF-102 turbofan engine. Time and spatial variations in tone noise obtained from closely spaced far-field and inlet duct microphones are displayed. Long (0.5 sec) to extremely short (0.001 sec) intermittent tone bursts are observed. Unsteadiness of the tone, its harmonics, and the broadband noise show little similarity. In the far-field, identity of tone bursts is retained over a directivity angle of less than 10 deg. In the inlet duct, tone bursts appear to propagate axially but exhibit little circumferential similarity. They show only slight relationship to tone bursts observed in the far field. The results imply an intermittent generation of random mixtures of propagating duct modes.

Clark, B. J.↗

Experimental analysis and computation of the onset and development of the boundary layer transition

The transition of an incompressible boundary layer, with zero pressure gradient and low free-stream turbulence is studied. Mean velocity, turbulence and Reynolds shear stress profiles are presented. The development of the Tollmien-Schlichting waves is clearly shown until the turbulent spots appear. The intermittency phenomenon is studied by conditional sampling of the hotwire signal. The comparison with calculation results obtained by resolution of a set of transport equations shows a good agreement for the mean characteristics of the flow; discrepancies observed for the turbulent quantities evolution are due to the intermittency phenomenon.

Arnal, D.↗

Hydrogen-fueled engine

A hydrogen-oxygen fueled internal combustion engine is described, which utilizes an inert gas, such as argon, as a working fluid to increase the efficiency of the engine, eliminate pollution, and facilitate operation of a closed cycle energy system. In a system where sunlight or other intermittent energy source is available to separate hydrogen and oxygen from water, the oxygen and inert gas are taken into a diesel engine into which hydrogen is injected and ignited. The exhaust is cooled so that it contains only water and the inert gas. The inert gas in the exhaust is returned to the engine for use with fresh oxygen, while the water in the exhaust is returned to the intermittent energy source for reconversion to hydrogen and oxygen.

Laumann, E. A.↗

Structure of the Turbulent Separated Flow Around a Stalled Airfoil

Hot-wire measurements were made in the boundary layer, the separated region, and the near wake for flow past a NACA 4412 airfoil at maximum lift. The Reynolds number based on chord was 1,500,000. Special care was taken to achieve a two-dimensional mean flow. Data were obtained at several thousand locations in the flow field. These data include intermittency, two components of mean velocity, and mean values for three double, four triple, and five quadruple products of two velocity fluctuations. No information was obtained about the third (spanwise) velocity component. Smoothing and interpolating routines were used to determine intermittency, two components of mean velocity, and mean values of three double, four triple, and five quadruple products of two velocity fluctuations on a fine rectangular mesh aligned with the airfoil chord. The data are presented in contour plots, in three-dimensional plots, and in tabular form. The format used to store the experimental data in digital form is described and a computer program which illustrates how this data can be accessed is presented.

Wadcock, A. J.↗

Application of split-film anemometer and mini-computer for measurement in turbulent separated flow

A split-film anemometer has been adapted for measurement of highly turbulent intermittently reversing flows in regions of local separation around airfoils and flaps. Analog signals from the split-film anemometer are fed directly to a mini-computer for processing and analysis. Mean velocity magnitude and direction, intermittency of reversal, turbulence intensity and histograms of the velocity are obtained as outputs of the system.

Wentz, W. H.↗

Energy efficient engine, low-pressure turbine boundary layer program

A study was conducted to investigate development of boundary layers under the influence of velocity distributions simulating the suction side of two state-of-the-art turbine airfoils: a forward loaded airfoil (squared-off design) and an aft loaded airfoil (aft-loaded design). These velocity distributions were simulated in a boundary layer wind tunnel. Detailed measurements of boundary layer mean velocity and turbulence intensity profiles were obtained for an inlet turbulence level of 2.4 percent and an exit Reynolds number of 800,000. Flush-mounted hot film probes identified the boundary layer transition regimes in the adverse pressure gradient regions for both velocity distributions. Wall intermittency data showed good agreement with the correlations of Dhawan and Narasimha for the intermittency factor distribution in transitional flow regimes.

Gardner, W. B.↗

Evaluation of a wall-flow direction probe for measurements in separated flows

The upstream-downstream flow direction intermittency is an important parameter that can quantitatively describe the stages of flow separation. This paper gives an improved design for a wall-flow-direction probe. Intermittency measurements made using this modified probe show agreement within experimental uncertainties with direct measurements made using a LDV, although both the unmodified and modified probe designs produce results that are consistently higher than those for the LDV.

Shivaprasad, B. G.↗

Oceanic corrosion test of bare and zinc-protected aluminum alloys for seawater heat exchangers

Bare 3004 tubes, 7072 Alclad 3004 tubes, and bare and zinc diffusion treated 3003 extrusions from a brazed aluminum, plate-fin heat exchanger were exposed to 1.8 m/sec flowing seawater aboard an open ocean test facility moored 3.4 km off the southeast coast of Puerto Rico. After six months exposure, the average corrosion rates for most varieties of aluminum materials converged to a low value of 0.015 mm/yr (0.6 mils/yr). Pitting did not occur in bare 3003 and 3004 samples during the six month test. Pitting did occur to varying degrees in the Alclad and zinc diffusion treated material, but did not penetrate to the base metal. Biofouling countermeasures (intermittent chlorination and brushing) did not affect the corrosion rates to any significant extent. Intermittent chlorination at a level of 0.5 ppm for 28 minutes daily controlled microbiofouling of the samples but did not prevent the development of a macrobiofouling community in areas of the plumbing with low flow.

Sasscer, D. S.↗

Interfacial fracture of Space-Shuttle thermal-protection system

Stable crack growth and fracture at the interface of undensified LI-900 reusable surface insulation (RSI) tile and the Nomex strain isolation pad (SIP) of the Space-Shuttle thermal-protection system (TPS) were modeled by double-edged notch-tension specimens. These specimens were loaded under uniaxial tension or 50-Hz cyclic loading and the resultant stable crack growth leading to eventual fracture was monitored by a videocamera. These tests showed that successive local tear-outs due to local tensile overload in the RSI tile resulted in the interfacial fracture where the crack-tip opening angle, CTOA, of the SIP was related to initiation and intermittent stable crack propagation. Fractures in similar static and dynamic test specimens using densified LI-900 RSI tiles occurred in the undensified regions of the RSI tiles. These failures were consistent with the above failure mechanism based on the local tensile strength of the undensified LI-900 RSI tile. The intermittent stable crack growth of undensified LI-900 RSI tile was reproduced by a deterministic, two-dimensional finite-element model with SIP of variable elastic moduli.

Komine, A.↗

Static versus dynamic loads as an influence on bone remodelling

Bone remodelling activity in the avian ulna was assessed under conditions of disuse alone, disuse with a superimposed continuous compressive load, and disuse interrupted by a short daily period of intermittent loading. The ulna preparation is made by two submetaphyseal osteotomies, the cut ends of the bone being covered with stainless steel caps which, together with the bone they enclosed, are pierced by pins emerging transcutaneously on the dorsal and ventral surfaces of the wing. The 110 mm long undisturbed section of the bone shaft can be protected from functional loading, loaded continuously in compression by joining the pins with springs, or loaded intermittently in compression by engaging the pins in an Instron machine. Similar loads (525 n) were used in both static and dynamic cases engendering similar peak strains at the bone's midshaft (-2000 x 10-6). The intermitent load was applied at a frequency of 1 Hz during a single 100 second period per day as a ramped square wave, with a rate of change of strain during the ramp of 0.01 per second.

Lanyon, L. E.↗

Influence of extended exposure in space on mechanical properties of high-toughness graphite-epoxy composite material (A0019)

Graphite-epoxy composites are promising candidates for structural use in space vehicles because of their high strength and elastic modulus properties. The problem of low fracture toughness was solved by use of recently developed techniques of intermittent interlaminar bonding. Before this material can be adapted for space use, however, confidence must be gained that its mechanical properties are not degraded by exposure to the space environment. The objective of this experiment is to test the effect of extended exposure to a space environment on the mechanical properties of a specially toughened T300/5208 graphite-epoxy composite material. Specimens made by recently developed techniques of intermittent interlaminar bonding will be exposed and afterward tested for fracture toughness, tensile strength, and elastic modulus. The approach of this experiment is to provide a frame on which the specimens can be mounted with their flat sides normal to the Long Duration Exposure Facility radius, each specimen with an unobstructed exposure of about 2 pi sr. The specimens will be mounted so that they neither fracture from high stress nor fail from excessive heating during launch and return.

Felbeck, D. K.↗

The rainout parameterization in a photochemical model

Photochemical models of tropospheric trace species typically simulate the effects of wet removal of soluble species from the atmosphere through a first-order rainout parameterization, which is independent of the species solubility and constant in time. In this work a modified first-order rainout parameterization is proposed that is a function of the species' solubility and takes into account the intermittent nature of atmospheric wet removal. In the case of a highly soluble species, such as HNO3, the inclusion of the effects of intermittent rainout in the parameterization leads to averaged rainout lifetimes considerably higher than ones used in most photochemical models. For illustrative purposes this parameterization is applied to a one-dimensional steady state model with parameterized eddy diffusion, although in principle it can be used in more sophisticated multidimensional models. The model results are compared to analagous calculations obtained with a 3-D tracer transport model.

Giorgi, F.↗

Space Station tethered refueling facility operations

The space-based orbital transfer vehicle will require a large cryogenic fuel storage facility at the Space Station. An alternative to fuel storage onboard the Space Station, is on a tethered orbital refueling facility (TORF) which is separated from the Space Station by a sufficient distance to induce a gravity gradient to settle the propellants. Facility operations are a major concern associated with a tethered LO2/LH2 storage depot. A study was carried out to analyze these operations so as to identify the preferred TORF deployment direction (up or down) and whether the TORF should be permanently or intermittently deployed. The analyses considered safety, contamination, rendezvous, servicing, transportation rate, communication, and viewing. An upwardly, intermittently deployed facility is the preferred configuration for a tethered cryogenic fuel storage.

Kiefel, E. R.↗

Ephemeral active regions and coronal bright points: A solar maximum Mission 2 guest investigator study

A dominate association of coronal bright points (as seen in He wavelength 10830) was confirmed with the approach and subsequent disappearance of opposite polarity magnetic network. While coronal bright points do occur with ephemeral regions, this association is a factor of 2 to 4 less than with sites of disappearing magnetic flux. The intensity variations seen in He I wavelength 10830 are intermittent and often rapid, varying over the 3 minute time resolution of the data; their bright point counterparts in the C IV wavelength 1548 and 20 cm wavelength show similar, though not always coincident time variations. Ejecta are associated with about 1/3 of the dark points and are evident in the C IV and H alpha data. These results support the idea that the anti-correlation of X-ray bright points with the solar cycle can be explained by the correlation of these coronal emission structures with sites of cancelling flux, indicating that, in some cases, the process of magnetic flux removal results in the release of energy. That the intensity variations are rapid and variable suggests that this process works intermittently.

Harvey, K. L.↗

An experimental study of surface pressure fluctuations in a separating turbulent boundary layer

Measurements of streamwise velocity fluctuation and surface pressure fluctuation spectra and wavespeeds are reported for a well-documented separating turbulent boundary layer. Because a portion of the acoustic pressure fluctuations is the same across the nominally two-dimensional turbulent flow, it is possible to decompose two microphone signals and obtain directly the turbulent flow contributions to the surface pressure spectra. The rms surface pressure fluctuation p' and spectra phi(omega) increase through the adverse pressure gradient attached flow region and the detached flow zone and scale on the maximum turbulent shearing stress tau(M); p'/tau(M) increases to the detachment location and decreases downstream due to the rapid movement of the pressure-fluctuation-producing motions away from the wall after the beginning of intermittent backflow. At lower frequencies for the attached flow phi(omega) is approximately omega to the -0.7 while phi(omega) is approximately omega to the -3 at higher frequencies. After the beginning of intermittent backflow, phi(omega) varies with omega at low frequencies and omega to the -3 at high frequencies; farther downstream the lower frequency range varies with omega to the 2.4. The surface pressure fluctuation celerity for the attached flow increases with frequency and agrees with the semi-logarithmic overlap equation of Panton and Linebarger. After the beginning of the separation process, the wavespeed decreases because of the oscillation of the instantaneous wavespeed direction and the streamwise coherence decreases drastically.

Simpson, Roger L.↗

The foreshock region upstream from the Comet Halley bow shock

A few hours prior to the crossing of the Comet Halley bow shock, the Giotto spacecraft intermittently encountered an electron foreshock region. The electron foreshock is characterized by magnetic connection to the cometary bow shock and increased field aligned electron heat flux directed away from the bow shock. A similar region was intermittently encountered by the ICE spacecraft prior to its crossing of the Giacobini-Zinner bow wave. During periods of magnetic connection with the Halley bow shock, enhanced magnetic field fluctuations were observed. These enhancements are interpreted as indirect evidence of an ion foreshock in the electron foreshock. No clearly identifiable backstreaming protons are observed during these periods of magnetic connection, however, because it may be difficult to separate a backstreaming population from the cometary pick-up proton population already present in the upstream region.

Fuselier, S. A.↗