Search NASA⌕ Search

SEARCH · Search NASA

Results for “linear approximation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Response of nonlinear panels to random loads

Lightweight aircraft structures exposed to a high intensity noise environment can fatigue prematurely if adequate consideration is not given to the problem. Design methods and design criteria for sonic fatigue prevention were developed based on analytical and experimental techniques. Most of the analytical work was based upon small deflection or linear structural theory which did not agree with the experimental results. A large deflection geometrical nonlinearity was incorporated into the analysis methods for determining the structural response to high intensity noise. The Karman-Herrmann large deflection equations with a single mode Galerkin approximation, and the method of equivalent linearization were used to predict mean square amplitude, mean square stresses, and nonlinear frequency at various acoustic loadings for rectangular panels. Both simply supported and clamped support conditions with immovable or movable inplane edges are considered. Comparisons with experimental results are presented.

Mei, C.↗

Approximations for inclusion of rotor lag dynamics in helicopter flight dynamics models

Approximate forms are suggested for augmenting linear rotor/body response models to include rotor lag dynamics. Use of an analytically linearized rotor/body model has shown that the primary effect comes from the additional angular rate contributions of the lag inertial response. Addition of lag dynamics may be made assuming these dynamics are represented by an isolated rotor with no shaft motion. Implications of such an approximation are indicated through comparison with flight test data and sensitivity of stability levels with body rate feedback.

Mckillip, Robert, Jr.↗

Techniques for measurement of thoracoabdominal asynchrony

Respiratory motion measured by respiratory inductance plethysmography often deviates from the sinusoidal pattern assumed in the traditional Lissajous figure (loop) analysis used to determine thoraco-abdominal asynchrony, or phase angle phi. We investigated six different time-domain methods of measuring phi, using simulated data with sinusoidal and triangular waveforms, phase shifts of 0-135 degrees, and 10% noise. The techniques were then used on data from 11 lightly anesthetized rhesus monkeys (Macaca mulatta; 7.6 +/- 0.8 kg; 5.7 +/- 0.5 years old), instrumented with a respiratory inductive plethysmograph, and subjected to increasing levels of inspiratory resistive loading ranging from 5-1,000 cmH(2)O. L(-1). sec(-1).The best results were obtained from cross-correlation and maximum linear correlation, with errors less than approximately 5 degrees from the actual phase angle in the simulated data. The worst performance was produced by the loop analysis, which in some cases was in error by more than 30 degrees. Compared to correlation, other analysis techniques performed at an intermediate level. Maximum linear correlation and cross-correlation produced similar results on the data collected from monkeys (SD of the difference, 4.1 degrees ) but all other techniques had a high SD of the difference compared to the correlation techniques.We conclude that phase angles are best measured using cross-correlation or maximum linear correlation, techniques that are independent of waveform shape, and robust in the presence of noise. Copyright 2002 Wiley-Liss, Inc.

Non-NASA Center↗

Stellar convection theory. I - The anelastic modal equations

Methods are developed for dealing with the various dynamical problems that arise because of convective zones in stars. A system of equations for stellar convection is derived from the full equations of compressible fluid dynamics with the aid of two major approximations. The first of these is the anelastic approximation, which involves both the filtering out of acoustic waves and a suitable linearization of the fluctuating thermodynamic variables. The second one approximates the horizontal structure of convection by expanding the motion in a set of horizontal cellular platforms and severely truncating the expansion. The resulting system of partial differential equations, referred to as the anelastic modal equations, is outlined along with suggested boundary conditions and techniques for solving the equations. Ways of assessing the overall validity of the present treatment are discussed.

Latour, J.↗

Guidance and Control System for a Satellite Constellation

A distributed guidance and control algorithm was developed for a constellation of satellites. The system repositions satellites as required, regulates satellites to desired orbits, and prevents collisions. 1. Optimal methods are used to compute nominal transfers from orbit to orbit. 2. Satellites are regulated to maintain the desired orbits once the transfers are complete. 3. A simulator is used to predict potential collisions or near-misses. 4. Each satellite computes perturbations to its controls so as to increase any unacceptable distances of nearest approach to other objects. a. The avoidance problem is recast in a distributed and locally-linear form to arrive at a tractable solution. b. Plant matrix values are approximated via simulation at each time step. c. The Linear Quadratic Gaussian (LQG) method is used to compute perturbations to the controls that will result in increased miss distances. 5. Once all danger is passed, the satellites return to their original orbits, all the while avoiding each other as above. 6. The delta-Vs are reasonable. The controller begins maneuvers as soon as practical to minimize delta-V. 7. Despite the inclusion of trajectory simulations within the control loop, the algorithm is sufficiently fast for available satellite computer hardware. 8. The required measurement accuracies are within the capabilities of modern inertial measurement devices and modern positioning devices.

Bryson, Jonathan Lamar↗

Approximation of discrete-time LQG compensators for distributed systems with boundary input and unbounded measurement

The approximation of optimal discrete-time linear quadratic Gaussian (LQG) compensators for distributed parameter control systems with boundary input and unbounded measurement is considered. The approach applies to a wide range of problems that can be formulated in a state space on which both the discrete-time input and output operators are continuous. Approximating compensators are obtained via application of the LQG theory and associated approximation results for infinite dimensional discrete-time control systems with bounded input and output. Numerical results for spline and modal based approximation schemes used to compute optimal compensators for a one dimensional heat equation with either Neumann or Dirichlet boundary control and pointwise measurement of temperature are presented and discussed.

Gibson, J. S.↗

Approximation of discrete-time LQG compensators for distributed systems with boundary input and unbounded measurement

The approximation of optimal discrete-time linear quadratic Gaussian (LQG) compensators for distributed parameter control systems with boundary input and unbounded measurement is considered. The approach applies to a wide range of problems that can be formulated in a state space on which both the discrete-time input and output operators are continuous. Approximating compensators are obtained via application of the LQG theory and associated approximation results for infinite dimensional discrete-time control systems with bounded input and output. Numerical results for spline and modal based approximation schemes used to compute optimal compensators for a one-dimensional heat equation with either Neumann or Dirichlet boundary control and pointwise measurement of temperature are presented and discussed.

Gibson, J. S.↗

A priori error estimates for an hp-version of the discontinuous Galerkin method for hyperbolic conservation laws

A priori error estimates are derived for hp-versions of the finite element method for discontinuous Galerkin approximations of a model class of linear, scalar, first-order hyperbolic conservation laws. These estimates are derived in a mesh dependent norm in which the coefficients depend upon both the local mesh size h(sub K) and a number p(sub k) which can be identified with the spectral order of the local approximations over each element.

Bey, Kim S.↗

Testing higher-order Lagrangian perturbation theory against numerical simulation. 1: Pancake models

We present results showing an improvement of the accuracy of perturbation theory as applied to cosmological structure formation for a useful range of quasi-linear scales. The Lagrangian theory of gravitational instability of an Einstein-de Sitter dust cosmogony investigated and solved up to the third order is compared with numerical simulations. In this paper we study the dynamics of pancake models as a first step. In previous work the accuracy of several analytical approximations for the modeling of large-scale structure in the mildly non-linear regime was analyzed in the same way, allowing for direct comparison of the accuracy of various approximations. In particular, the Zel'dovich approximation (hereafter ZA) as a subclass of the first-order Lagrangian perturbation solutions was found to provide an excellent approximation to the density field in the mildly non-linear regime (i.e. up to a linear r.m.s. density contrast of sigma is approximately 2). The performance of ZA in hierarchical clustering models can be greatly improved by truncating the initial power spectrum (smoothing the initial data). We here explore whether this approximation can be further improved with higher-order corrections in the displacement mapping from homogeneity. We study a single pancake model (truncated power-spectrum with power-spectrum with power-index n = -1) using cross-correlation statistics employed in previous work. We found that for all statistical methods used the higher-order corrections improve the results obtained for the first-order solution up to the stage when sigma (linear theory) is approximately 1. While this improvement can be seen for all spatial scales, later stages retain this feature only above a certain scale which is increasing with time. However, third-order is not much improvement over second-order at any stage. The total breakdown of the perturbation approach is observed at the stage, where sigma (linear theory) is approximately 2, which corresponds to the onset of hierarchical clustering. This success is found at a considerable higher non-linearity than is usual for perturbation theory. Whether a truncation of the initial power-spectrum in hierarchical models retains this improvement will be analyzed in a forthcoming work.

Buchert, T.↗

Advances in dual algorithms and convex approximation methods

A new algorithm for solving the duals of separable convex optimization problems is presented. The algorithm is based on an active set strategy in conjunction with a variable metric method. This first order algorithm is more reliable than Newton's method used in DUAL-2 because it does not break down when the Hessian matrix becomes singular or nearly singular. A perturbation technique is introduced in order to remove the nondifferentiability of the dual function which arises when linear constraints are present in the approximate problem.

Smaoui, H.↗

Equivalent linearization for fatigue life estimates of a nonlinear structure

An adaptation of the method of equivalent linearization is developed in order to estimate the fatigue life of a nonlinear structure excited by Gaussian white noise. While conventional equivalent linearization has been successfully applied to approximate the mean square responses of the variety of complex nonlinear systems, it has not been possible to apply the method for fatigue predictions. This limitation results from the assumption that the probability density of the response of the nonlinear system is Gaussian, which is not generally true. In the present effort, a modification of equivalent linearization, developed by the author, is employed which has been shown in recent studies to provide a much more accurate description of the random response of a nonlinear structure than provided by conventional equivalent linearization. A method is presented for estimating fatigue life based on this approach and results are compared with those obtained using both numerical simulation and the classical method. The fatigue life is estimated for a nonlinear plate vibrating in a single resonant mode with random white noise excitation. Excellent agreement is found between all three methods. These results indicate that equivalent linearization may be extended to predict the fatigue life of more complex nonlinear systems than can be analyzed at present.

Miles, R. N.↗

Micromechanics of intraply hybrid composites: Elastic and thermal properties

Composite micromechanics are used to derive equations for predicting the elastic and thermal properties of unidirectional intraply hybrid composites. The results predicted using these equations are compared with those predicted using approximate equations based on the rule of mixtures, linear laminate theory, finite element analysis and limited experimental data. The comparisons for three different intraply hybrids indicate that all four methods predict approximately the same elastic properties and are in good agreement with measured data. The micromechanics equations and linear laminate theory predict about the same values for thermal expansion coefficients. The micromechanics equations predict through-the-thickness properties which are in good agreement with the finite element results.

Chamis, C. C.↗

Structural behavior of scientific balloons - Finite element simulation and verification

An off-the-shelf nonlinear finite element code was used to analyze fully inflated scientific balloons. The thin balloon film was modeled by shell bending elements. Numerical difficulties caused by insignificant bending stiffness terms were overcome by introducing some artificial bending stiffness. This approximation is justified by the fact that in thin shells with nonzero Gaussian curvature the membrane solution component is essentially independent of the bending solution component. Perturbation of the coveraged solution by increasing the bending stiffness by a full decade verified this assertion. This analytical approach was experimentally verified. As a result of this verification process it was discovered that the generally accepted linearly visco-elastic model for polyethylene film is inappropriate for a significant planar (as opposed to uniaxial) stress state. A linear elastic model presents a good approximation for planar stress states.

Schur, Willi W.↗

Neural Network and Regression Approximations in High Speed Civil Transport Aircraft Design Optimization

Nonlinear mathematical-programming-based design optimization can be an elegant method. However, the calculations required to generate the merit function, constraints, and their gradients, which are frequently required, can make the process computational intensive. The computational burden can be greatly reduced by using approximating analyzers derived from an original analyzer utilizing neural networks and linear regression methods. The experience gained from using both of these approximation methods in the design optimization of a high speed civil transport aircraft is the subject of this paper. The Langley Research Center's Flight Optimization System was selected for the aircraft analysis. This software was exercised to generate a set of training data with which a neural network and a regression method were trained, thereby producing the two approximating analyzers. The derived analyzers were coupled to the Lewis Research Center's CometBoards test bed to provide the optimization capability. With the combined software, both approximation methods were examined for use in aircraft design optimization, and both performed satisfactorily. The CPU time for solution of the problem, which had been measured in hours, was reduced to minutes with the neural network approximation and to seconds with the regression method. Instability encountered in the aircraft analysis software at certain design points was also eliminated. On the other hand, there were costs and difficulties associated with training the approximating analyzers. The CPU time required to generate the input-output pairs and to train the approximating analyzers was seven times that required for solution of the problem.

Patniak, Surya N.↗

On the parallel solution of parabolic equations

Parallel algorithms for the solution of linear parabolic problems are proposed. The first of these methods is based on using polynomial approximation to the exponential. It does not require solving any linear systems and is highly parallelizable. The two other methods proposed are based on Pade and Chebyshev approximations to the matrix exponential. The parallelization of these methods is achieved by using partial fraction decomposition techniques to solve the resulting systems and thus offers the potential for increased time parallelism in time dependent problems. Experimental results from the Alliant FX/8 and the Cray Y-MP/832 vector multiprocessors are also presented.

Gallopoulos, E.↗

A fast semi-implicit algorithm for problems of mixed type

Certain physical processes are modeled by partial differential equations which are parabolic over part of the domain and elliptic over the remainder. A family of semi-implicit algorithms which are well suited to initial-boundary value problems of this mixed type is discussed. One important feature of these algorithms is the use of an approximate inverse for the solution of the implicit linear system. A strong error analysis results in an estimate of the total error as a function of approximate inverse error e and time step h.

Frederickson, P. O.↗

Stratospheric warmings diagnosed using the transformed Eulerian-mean equations and the effect of the mean state on wave propagation

Terms for the transformed Eulerian equations are calculated in order to characterize the phenomenom of sudden stratospheric warming. The transformed diagnostics are applied to data for warmings during Dec. and Jan. 1976-1977, as well as cross sections for the directions of the Eiliassen-Palm (EP) fluxes and residual mean meridional circulations. The convergence of the EP flux was determined to provide a strong approximation to the total effect of waves in forcing the zonal mean flow. The EP fluxes change from an upward and equatorward direction to an upward and poleward direction during the warmings, and indications are reported that the effect is due to a feedback on wave propagation of an evolving mean flow. Ray paths in the meridional plane are computed for different mean wind fields to determine the direction of wave propagation according to linear theory based on the WKB approximation.

Oneill, A.↗

Finite-dimensional compensators for infinite-dimensional systems via Galerkin-type approximation

In this paper existence and construction of stabilizing compensators for linear time-invariant systems defined on Hilbert spaces are discussed. An existence result is established using Galkerin-type approximations in which independent basis elements are used instead of the complete set of eigenvectors. A design procedure based on approximate solutions of the optimal regulator and optimal observer via Galerkin-type approximation is given and the Schumacher approach is used to reduce the dimension of compensators. A detailed discussion for parabolic and hereditary differential systems is included.

Ito, Kazufumi↗