SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Report describes method of verification of solar space heating and hot-water systems using similarity comparison, mathematical analysis, inspections, and tests. Systems, subsystems, and components were tested for performance, durability, safety, and other factors. Tables and graphs compliment test materials.
Progress made by the Low-Cost Silicon Solar Array Project during the period January through March 1978 is reported. It includes task reports on silicon material processing, large-area silicon sheet development, encapsulation materials testing and development, project engineering and operations, and manufacturing techniques, plus the steps taken to integrate these efforts.
Topics discussed include silicon material processing; large-area silicon sheet development; encapsulation materials testing and development; project engineering and operations activities, and manufacturing techniques. The steps taken to integrate these efforts, are described.
Inexpensive, cosine-corrected radiometer measures ultraviolet radiation. In field use, instrument tests materials for effects of ultraviolet exposure and studies solar-cell degradation. It consists of cup-shaped diaphragm and diffusing dome for corrected response, two filters that select wavelength range, and silicon solar cell. Filters control response within passband of 300 to 400 nm.
P2sup.L2sup. strain monitor measures strain by monitoring change in phase of acoustic signal that passes through stressed sample. Phase sample causes shift in frequency of VCO. As with other monitors of this type, instrument is only accurate in elastic range of material. Monitor is expected to have broad application in materials testing, structural design, fabrication and assembly.
The results of an experimental program are described which establishes the feasibility and guide lines for resin development. The objective was to identify the basic epoxy neat resin properties that improve low velocity impact resistance and toughness to graphite-epoxy laminates and at the same time maintain useful structural laminate mechanical properties. Materials tests from twenty-three toughened epoxy resin matrix systems are included.
A description is presented of work concerned with determining the effects of long-term flight service on advanced composite helicopter airframe components. The helicopter chosen for the program is the Long Ranger Model 206L. The components to be evaluated include the baggage door, litter door, vertical fin, and forward fairing. Only the vertical fin is classified as primary structure. Loss of any of the other components will not compromise safety of the aircraft. Attention is given to the program objectives, the design of the forward fairing, the fabrication procedures, the exterior surface, the cocure procedure, material tests, and initial cost-tracking. The considered program demonstrates the ability to produce an acceptable fairing by the 'one-shot' cocured process and, based on learning curve experience, production costs will be low. The low-temperature 200 F cure does not affect the structural properties to an unacceptable degree. A method for obtaining a smooth, exterior painted surface for Kevlar/epoxy fabric has been developed.
A Priest laser interferometer was developed to measure the thermal strain of composite laminates. The salient features of this interferometer are that: (1) it operates between 116 K and 366 K; (2) it is easy to operate; (3) minimum specimen preparation is required; (4) coefficients of thermal expansion in the range of 0-5 micro epsilon/K can be measured; and (5) the resolution of thermal strain is on the order of micro epsilon. The thermal response of quasi-isotropic, T300/5208, grahite-epoxy composite material was studied with this interferometer. The study showed that: (1) for the material tested, thermal cycling effects are negligible; (2) variability of thermal response from specimen to specimen may become significant at cryogenic temperatures; and (3) the thermal response of 0.6 cm and 2.5 cm wide specimens are the same above room temperature.
An exact solution for the stress field within a rectangular slab of orthotropic material is found using a two dimensional Fourier series formulation. The material is required to be in plane stress, with general stress boundary conditions, and the principle axes of the material must be parallel to the sides of the rectangle. Two load cases similar to those encountered in materials testing are investigated using the solution. The solution method has potential uses in stress analysis of composite structures.
Commercially-produced, pressureless sintered Si3N4, SiC, and SiAlON were characterized with respect to density, phases present, bend strength, and oxidation resistance. The room-temperature bend strengths of sintered Si3N4, SiC, and SiAlON are comparable. However, the room-temperature strengths are much lower (approximately 40 to 50%) than the room-temperature strength of hot-pressed Si3N4 (NC-132). The strength loss in Si3N4 and SiAlON materials at high temperature was attributed to a viscous grain-boundary phase, retained during cooling from the sintering temperature. The oxidation resistance of sintered alpha-SiC was the best of any materials tested.
Alloy tubes filled with hydrogen doped with various amounts of carbon monoxide, carbon dioxide, ethane, ethylene, methane, ammonia, or water were heated in a diesel fuel-fired Stirling engine simulator materials test rig for 100 hours at 21 MPa and 760 or 820 C to determine the effectiveness of the dopants in reducing hydrogen permeation through the hot tube walls. Ultra high purity (UHP) hydrogen was used for comparison. The tube alloys were N-155, A-286, Incoloy 800, Nitronic 40, 19-9DL, 316 stainless steel, Inconel 718, and HS-188. Carbon dioxide and carbon monoxide in the concentration range 0.2 to 5 vol % were most effective in reducing hydrogen permeation through the hot tube walls for all alloys. Ethane, ethylene, methane, ammonia, and water at the concentrations investigated were not effective in reducing the permeation below that achieved with UHP hydrogen. One series of tests were conducted with UHP hydrogen in carburized tubes. Carburization of the tubes prior to exposure reduced permeation to values similar to those for carbon monoxide; however, carbon dioxide was the most effective dopant.
The selection of structural alloys, composite materials, solder alloys, and filler materials for use in cryogenic models is discussed. In particular, materials testing programs conducted at Langley are described.
Literature concerning strength (failure) criteria for composite materials is reviewed with emphasis on phenomenological failure criteria. These criteria are primarily intended to give a good estimation of the safety margin with respect to failure for arbitrary multiaxial stress states. The failure criteria do not indicate the types of fracture that will occur in the material. The collection of failure criteria is evaluated for applicability for the glass reinforced plastics used in mine detectors. Material tests necessary to determine the parameters in the failure criteria are discussed.
Toroidal induction heater is key element in rapid bonding technique. Rapid adhesive bonding equipment features toroid induction heater for quick bonding of composites and metals. Process avoids damaging composites that cannot withstand high temperatures for long time intervals. Process scaled up for production. Technique suited to bonding of end tabs onto material test specimens.
Tubes of CG-27 alloy, filled with hydrogen doped with various amounts of carbon dioxide and carbon monoxide, were heated in a diesel fuel fired Stirling engine simulator materials test rig for 100 hours at 820 C and at a gas pressure of 15 MPa to determine the effectiveness of the dopants in reducing hydrogen permeation through the hot tube wall. This was done for clean as-heat treated tubes and also for tubes that had previously been exposed for 100 hours to hydrogen doped with 1.0 volume percent carbon dioxide to determine if the lower levels of dopant could maintain a low hydrogen permeation through the hot tube wall. Carbon dioxide, as a dopant in hydrogen, was most effective in reducing hydrogen permeation through clean tubes and in maintaining low hydrogen permeation after prior exposure to 1.0 volume percent carbon dioxide. Only the lowest level of carbon dioxide (0.05 volume percent) was not as effective in the clean or prior exposed tubes. Carbon monoxide as a dopant in hydrogen was less effective than carbon dioxide at a given concentration level. Of the four dopant levels studied; 1.0, 0.5, 0.2, and 0.05 volume percent carbon monoxide, only the 1.0 and 0.5 volume percent were effective in reducing and maintaining low hydrogen permeation through the CG-27.
To explain the unidentified spectral features of Io, as obtained by the Voyager infrared spectrometer experiment, the infrared absorption spectra of a number of stable sulfur and oxygen compounds was measured and compared to the Voyager data. Based on the reference absorption bands of Na2SO4 and possibly SO2, the infrared data on Io in the region 700 to 200 per cm appear to represent an emission spectrum. Given the strong evidence for an oxidized crustal environment and the presence of sodium in the Io torus, the absorption spectra of the tested materials support the probability of Na2SO4 occurrence on Io.
Many of the passive experiments flying on LDEF will be significantly enhanced if data are available postflight to indicate the temperature time histories of test materials and other specimens exposed in the experiments. The baseline LDEF approach was to provide postflight calculated temperature histories of experiment boundaries and solar flux data for the mission, which can in turn be used by each investigator to calculate the temperature time histories for critical experiment components. Without in-flight temperature measurements, a substantial uncertainty will exist in the calculated temperatures. The data measured by the themal measurement system (THERM) will significantly improve postflight knowledge of temperatures experienced by LDEF experiments. The THERM data will also be valuable in validating the LDEF thermal design concept and in providing better design data for experimenters on future LDEF missions. The objectives of this experiment are to determine the history of the interior average temperatures of the LDEF for the total orbital mission and to measure the temperatures of selected components and thermal boundary conditions.
Fatigue crack growth and retardation experiments conducted in polycarbonate test specimen are described. The transparent test material allows optical interferometry measurements of the fatigue crack opening (and closing) profiles. Crack surface displacements are obtained through the specimen thickness and three dimensional aspects of fatigue crack closure are discussed.