Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Investigation of Microstructures and Tensile Properties of 316L Stainless Steel Fabricated via Laser Powder Bed Fusion

In this study, a thorough investigation of the microstructures and tensile properties of 316L stainless steel fabricated via laser powder bed fusion (L-PBF) was done. 316L stainless steel specimens with two different thicknesses of 1.5 mm and 4.0 mm fabricated under similar conditions were utilized. Microstructural characterization was performed using optical microscopy (OM) and scanning electron microscopy (SEM) equipped with electron backscatter diffraction (EBSD). Melt pools and cellular structures were observed using OM, whereas EBSD was utilized to obtain the grain size, grain boundary characteristics, and crystallographic texture. The 1.5 mm thick sample demonstrated a yield strength (YS) of 538.42 MPa, ultimate tensile strength (UTS) of 606.47 MPa, and elongation to failure of 69.88%, whereas the 4.0 mm thick sample had a YS of 551.21 MPa, UTS of 619.58 MPa, and elongation to failure of 73.66%. These results demonstrated a slight decrease in mechanical properties with decreasing thickness, with a 2.4% reduction in YS, 2.1% reduction in UTS, and 5.8% reduction in elongation to failure. In addition to other microstructural features, the cellular structures were observed to be the major contributors to the high mechanical properties. Using the inverse pole figure (IPF) maps, both thicknesses depicted a crystallographic texture of {001} <101> in their as-built state. However, when subjected to tensile loads, texture transitions to {111} <001> and {111} <011> were observed for the 1.5 mm and 4.0 mm samples, respectively. Additionally, EBSD analysis revealed the pre-existence of high-density dislocation networks and a high fraction of low-angle grain boundaries. Interestingly, twinning was observed, suggesting that the plastic deformation occurred through dislocation gliding and deformation twinning.

316L stainless steel↗

PHENIX U.S.-Japan Collaboration Investigation of Thermal and Mechanical Properties of Thermal Neutron–Shielded Irradiated Tungsten

The United States and Japan have collaborated on fusion materials research in a series of agreements reaching back to 1981. The PHENIX collaboration is the latest U.S.-Japan project which spans 2013 to 2019 and has the goal of assessing technical feasibility of tungsten-based, helium-cooled plasma-facing component concepts for a demonstration fusion power reactor (DEMO). Task 2 within the PHENIX project is focused on evaluating the neutron irradiation effects in tungsten. For tungsten, the transmutation to Re and Os is at least as important to determining its properties after irradiation as the displacement damage, and the transmutation rate depends on the energy spectrum of the reactor. A large-scale, instrumented irradiation capsule with thermal neutron shielding to better mimic fusion conditions was irradiated in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory. The tungsten specimens were irradiated in different temperature zones between 500°C and 1200°C to doses of ~0.2 to 0.7 displacements per atom. More than 20 varieties of pure tungsten and tungsten alloys were included in the irradiation, and they were evaluated in the 3025E hot-cell facility and at the Low Activation Materials Development and Analysis Laboratory. The elevated temperature tensile, fracture toughness, hardness, thermal conductivity, electrical resistivity, density, elemental composition, and microstructure properties of the irradiated materials are being collected. Furthermore, this paper overviews the experimental design, specimen matrix, and the initial results of postirradiation examinations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experiments for electromagnetic levitation in microgravity

Containerless processing is a promising research tool for investigating the properties of undercooled melts and their solidification. For conducting samples RF-electromagnetic levitation offers the possibility to obtain large undercoolings by avoiding heterogeneous nucleation at container walls. On earth, however, strong magnetic fields are needed to compensate the gravitational force which imposes a lower limit on the available temperatures and on the accessible undercooling range. Under microgravity conditions the magnetic positioning fields can be minimized and hence, undercooling becomes feasible under ultra-high vacuum conditions and lower temperatures become accessible. In contrast to other undercooling and solidification techniques, electromagnetic levitation allows for diagnostic measurements during the early steps of nucleation and phase selection. Experiments cover a wide field of research topics: nucleation, directional solidification at high velocities, generation of metastable phases, evolution of microstructures, properties of undercooled liquids. Examples from these classes including experiments selected for the IML-2 mission are discussed with emphasis on technical requirements. An overview is given on the German TEMPUS (electromagnetic levitation facility) program.

Willnecker, R.↗

Effect of Fe Substitution on Microstructure and Magnetic Properties of Ni{sub 1−x}Fe{sub x}O{sub 2} Nanoparticles

Fe-substituted NiO nanoparticles (Ni{sub 1−x}Fe{sub x}O{sub 2}) (x= 0.00, 0.03, 0.05, 0.07, and 0.09) were synthesised using ball-milling method followed by vacuum sintering and studied for their microstructural and magnetic properties. All the samples show a cubic structure with a crystallite size of 17–26 nm. Secondary phases related to Fe{sub 2}O{sub 3} were identified from XRD, indicating that the observed ferromagnetism may be due to the dopants. The doping of Fe ions does not cause any significant variation in the crystal structure. The pure NiO nanoparticles were weak ferromagnetic in nature, and Fe-doped NiO nanoparticles exhibit room temperature ferromagnetism. The strength of magnetization increased from 0.57 to 0.94 emu/g with an increase of Fe concentration from 3 to 7 at.%, respectively. A high coercive field of 173 Oe was observed for the Ni{sub 1−x}Fe{sub x}O{sub 2} nanoparticles at x= 0.09. The results and the process of development of ferromagnetism at room temperature in the Ni{sub 1−x}Fe{sub x}O{sub 2} nanoparticles were presented and discussed in detail.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Impedance characteristics and PTCR effect in lead free BaTi1-xSnxO3 piezoceramics

Highlights: • The maximum d{sub 33} = 296 pC/N and P{sub r} = 6.92 μC/cm{sup 2} is observed for x = 0.08. • Nyquist plots reveal non-Debye type relaxation behavior of the samples. • Impedance studies indicate a possible correlation between d{sub 33} and microstructure. • Positive temperature coefficient of resistance (PTCR) is seen just above T{sub C}. - Abstract: BaTi{sub 1-x}Sn{sub x}O{sub 3} of compositions x = 0.07, 0.08, 0.09, 0.10 and 0.11 are synthesized to study their piezoelectric and impedance characteristics. The studies revealed that the composition x = 0.08 exhibits the maximum piezoelectric coefficient (d{sub 33} = 296 pC/N) and remnant polarization (P{sub r} = 6.92 μC/cm{sup 2}) values. The impedance analysis showed that the depressed semi-circular arc observed in the Nyquist’s plots gave evidence for the existence of non-Debye type relaxation behavior in the compounds. The impedance studies suggested a possible correlation between the d{sub 33} and microstructural properties. The activation energies extracted from ac conductivity plots strongly indicate the existence of defect dipole assisted conductivity mechanism in the samples. Notably, the samples displayed positive temperature coefficient of resistance (PTCR) just above their ferroelectric transition. The frequency dependent ac conductivity follows the Jonscher’s universal power law. The dominant conduction mechanism in the samples is determined to be the small polaron hopping mechanism.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Microstructures and mechanical properties of a welded CoCrFeMnNi high-entropy alloy

The response of the CoCrFeMnNi high-entropy alloy to weld thermal cycles was investigated to determine its applicability as an engineering structural material. Two processes were used: high-energy-density, low-heat-input electron beam (EB) welding and low-energy-density, high-heat-input gas tungsten arc (GTA) welding. Weldability was determined through comprehensive microstructural and mechanical property characterisation of the welds. The welds did not develop solidification cracking or heat-affected zone cracks. The microstructures in weld fusion zones are similar to that in the as-cast materials, consisting of large columnar grains with dendrite. The dendrite arm spacing and the extent of elemental segregation were less in the welds than in the cast ingot, and also were less pronounced in the EB weld than in the GTA weld. Compositional microsegregation between dendritic cores and interdendritic regions of the welds was insignificant. Both welds exhibited slightly higher yield strengths than the base metal. The EB weld possessed comparable tensile strength and ductility to that of the base metal. In comparison, the GTA weld maintained ∼80% of the base metal's tensile strength and 50% of the ductility.

36 MATERIALS SCIENCE↗

Gas tungsten arc welding and post weld heat treatment effects on microstructure and mechanical property of castable nanostructured alloy steel

Here, this paper details the first study of castable nanostructured alloy (CNA) steel gas tungsten arc weldability and the post-weld heat treatment (PWHT) effects. Effects of welding heat input, thermal cycles, and PWHT on microstructures, microhardness distributions, room temperature tensile properties, and fracture characteristics are discussed. Results show that CNA steel exhibits excellent weldability (i.e., no indication of welding defects and reasonable tensile properties). The welded joint exhibited heterogeneous microstructures with δ-ferrite as well as large microhardness variation and fluctuation. The welded joint yield and ultimate tensile strengths were similar to those of the base metal, but the elongations decreased by 30 %. However, with normalization and tempering PWHT, the δ-ferrite was eliminated, microstructure was modified, hardness was unified, and joint ductility was restored. The study indicated that the CNA reduced-activation ferritic-martensitic steel owns excellent weldability, and PWHT is needed for the industrial application of welded structures.

36 MATERIALS SCIENCE↗

Epoxy resin reinforced with carbonized chicken feathers: An innovative composite material with sustainable potentials

Here, this article explores a novel method for enhancing the mechanical properties of epoxy resin composites by incorporating carbonized chicken feathers as a filler material. The fabrication process involves carbonizing chicken feathers at 600°C and incorporating 5-10 wt% of the fillers into an epoxy matrix. The composites showed enhanced mechanical properties and samples containing 10 wt% filler exhibit the best properties. The performance corresponds to 49% increase in tensile strength, 16% rise in Young’s modulus, 40% improvement in flexural modulus, and 57% in flexural strength. X-ray diffraction and scanning electron microscopy with energy dispersive spectroscopy were employed to characterize the filler. This characterization provides valuable insights into the structure and chemical composition of the pulverized carbonized chicken feathers that contributed to the attained improvement in composites’ properties. Microstructural examination of the developed composite under scanning electron microscope also provides insights into matrix-filler interface and dispersion of the fillers within the composite matrix. The study not only highlights the unique combination of carbonized feathers’ inherent strength and compatibility with the epoxy matrix but also underscores the eco-friendly nature of utilizing agricultural waste. The findings suggest promising applications in industries demanding lightweight, high-strength materials, which can contribute to sustainable engineering solutions.

36 MATERIALS SCIENCE↗

Tailoring Microstructure and Mechanical Properties of Additively-Manufactured Ti6Al4V Using Post Processing

Additively-manufactured Ti-6Al-4V (Ti64) exhibits high strength but in some cases inferior elongation to those of conventionally manufactured materials. Post-processing of additively manufactured Ti64 components is investigated to modify the mechanical properties for specific applications while still utilizing the benefits of the additive manufacturing process. The mechanical properties and fatigue resistance of Ti64 samples made by electron beam melting were tested in the as-built state. Several heat treatments (up to 1000 °C) were performed to study their effect on the microstructure and mechanical properties. Phase content during heating was tested with high reliability by neutron diffraction at Los Alamos National Laboratory. Two different hot isostatic pressings (HIP) cycles were tested, one at low temperature (780 °C), the other is at the standard temperature (920 °C). The results show that lowering the HIP holding temperature retains the fine microstructure (~1% β phase) and the 0.2% proof stress of the as-built samples (1038 MPa), but gives rise to higher elongation (~14%) and better fatigue life. The material subjected to a higher HIP temperature had a coarser microstructure, more residual β phase (~2% difference), displayed slightly lower Vickers hardness (~15 HV10N), 0.2% proof stress (~60 MPa) and ultimate stresses (~40 MPa) than the material HIP’ed at 780 °C, but had superior elongation (~6%) and fatigue resistance. Heat treatment at 1000 °C entirely altered the microstructure (~7% β phase), yield elongation of 13.7% but decrease the 0.2% proof-stress to 927 MPa. The results of the HIP at 780 °C imply it would be beneficial to lower the standard ASTM HIP temperature for Ti6Al4V additively manufactured by electron beam melting.

36 MATERIALS SCIENCE↗

On the nexus between atom probe microscopy and density functional theory simulations

The capability of precisely determining the atomic identity and position, coupled with an understanding of the inter-atomic interactions is crucial to enabling microstructure-property relationships in modern materials science. Two approaches to the investigation of materials at the atomic-scale are atom probe microscopy (APM) and density functional theory (DFT). On the one hand, APM offers an ultimate in 3D elemental analysis by determining the chemical identity and atomic position in a material. On the other, first principles DFT simulations allow the prediction of atomic structure and, critically, the electronic structure which is the gateway to calculating the real-world properties of materials. Both approaches are undertaken at the atomic-scale, and so are intrinsically complementary. This paper provides a review of the opportunities and challenges in combining these approaches to do materials science. We first summarise the status of these approaches and set out a framework for the current main workflows by which APM experiments inform DFT simulations and vice-versa. We point out certain gaps between the approaches and ways that these may be bridged via a series of case-studies organised into the aforementioned workflow framework.

36 MATERIALS SCIENCE↗

Integration of Information Management System, Workflow and Computational Tools Enabling Multiscale Modeling Within an ICME Paradigm

With the increased emphasis on reducing the cost and time to market of new materials, the need for analytical tools that enable the virtual design and optimization of materials throughout their processing - internal structure - property - performance envelope, along with the capturing and storing of the associated material and model information across its lifecycle, has become critical. This need is also fueled by the demands for higher efficiency in material testing; consistency, quality and traceability of data; product design; engineering analysis; as well as control of access to proprietary or sensitive information. Fortunately, material information management systems and physics-based multiscale modeling methods have kept pace with the growing user demands. Herein, recent efforts to develop a set of Python functions that exchange information between NASA GRC's Integrated multiscale Micromechanics Analysis Code (ImMAC) software toolset and its Integrated Computational Materials Engineering (ICME), Granta MI® database schema is presented. The goal is to enable seamless coupling between both test data and simulation data, which is captured and tracked automatically within Granta MI®, with full model pedigree information. These tools, and this type of linkage, are foundational to realizing the full potential of ICME, in which materials processing, microstructure, properties, and performance are coupled to enable application-driven design and optimization of materials and structures.

multiscale modeling; Micromechanics; Computational↗

Annealing Effects on Microstructure and Magnetic Properties of (NdPr){sub 9.5}(FeNbCoCu){sub 79.5}(BC){sub 11} Nanocomposite Magnets

Annealing effects on microstructure and magnetic properties of (NdPr){sub 9.5}(FeNbCo){sub 79.5}(BC){sub 11} ribbons were investigated. It was observed that Nd{sub 2}Fe{sub 14}B and Fe{sub 3}B phases were directly formed at low spinning speed. Then, the alloys transformed to an amorphous state at a speed of 20 m/s. Annealed at 700 {sup ∘}C for 10 min, the amorphous alloys as-quenched at 20 m/s crystallized into a nanocomposite composed of Nd{sub 2}Fe{sub 14}B and α-Fe phases. The formation of Fe{sub 3}B phases was inhibited. The magnetic properties firstly increased and then decreased with the increasing of annealing time. The optimum magnetic properties were achieved in the alloys annealed at 700 {sup ∘}C for 10 min. The corresponding coercivity, remanence, and the maximum energy product was 427.5 kA/m, 0.94 T, and 101.2 kJ/m{sup 3}, respectively. In addition, fine and uniform grains were formed. The average grain size was 10 nm.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Microstructure and Mechanical Properties of Extruded Mg-7Sn-5Zn-xAl (x = 0, 1, 2 and 3 wt.%) Alloy

Microstructure and mechanical properties of extruded Mg-7Sn-5Zn-xAl (x = 0, 1, 2 and 3 wt.%) alloy were investigated. The as-cast Mg-7Sn-5Zn alloy mainly comprised α-Mg dendrites, Mg{sub 2}Sn and nanosized Mg-Zn phases in a Mg matrix, whereas the quasicrystal (icosahedral (I)) phase precipitated with the addition of Al. After extrusion, the grain size decreased due to dynamic recrystallization and the resulting particles were crushed and distributed along the extrusion direction. The highest tensile strength was exhibited by the extruded Mg-7Sn-5Zn-2Al alloy, which had a yield strength, ultimate tensile strength and elongation to failure of 198, 343 MPa and 18.7%, respectively. The high tensile strength was mainly attributed to grain refinement and precipitation strengthening of the Mg{sub 2}Sn and icosahedral phases.

36 MATERIALS SCIENCE↗

Effects of Cu and Zn on microstructures and mechanical behavior of the medium-entropy aluminum alloy

Lightweight alloys are becoming more and more important. Based on the 5083 aluminum alloy, the effects of Zn and Cu additions on the microstructures, properties, and serration behavior were investigated. The results show that with the increase of the Zn content, the tensile and yield strengths of the alloy increase, while the elongation and the serration amplitude keep on decreasing. Moreover, different amounts of Cu are added to the high Zn content Al–Mg-6 wt.% (weight percent) Zn alloy, in which the strength and plasticity are improved firstly. We find that when the Cu content was 6 wt%, the elongation of the alloy is about 7%, and the serration behavior of the alloy gradually disappears. The optimal mechanical property is achieved at the composition of Al–Mg-6wt.%Zn-6wt.%Cu. Furthermore, the serration behavior is believed to be related to the interaction between the moving dislocations and the precipitates. Furthermore, the serrated flow was analyzed using the refined composite multiscale entropy algorithm. It was found that the dynamical complexity of the serrations generally increased with an increase in the solute density, the stress-drop magnitude, the grain size, the tensile and yield strengths, and the degree of plasticity.

36 MATERIALS SCIENCE↗

A facile method for rapid preparation of individual titania nanotube powders by a two-step process

Research highlights: {yields} Rapid and facile preparation of individual titania nanotube powders. {yields} Combination of the electrochemical process and the physical processing. {yields} Post ultrasonic treatment acts as the key factor to obtain the individual TiO{sub 2} NT powders. {yields} Individual TiO{sub 2} NTs powder owns higher photocatalytic activities. -- Abstract: Present study reports a facile method for preparing individual TiO{sub 2} nanotube (NT) powders by a two-step process, which includes that TiO{sub 2} NT bundles are rapidly synthesized by an electro-chemical process in perchlorate-containing electrolyte and then they are disaggregated into individual TiO{sub 2} NT powders under an assistance of ultrasonic oscillation treatment. Morphological and microstructural properties of the individual TiO{sub 2} NT powders are characterized by field emission scanning electron microscopy and transmission electron microscopy. Results indicate that the individual TiO{sub 2} NT powders, which have an outer diameter of about 20 nm and an inner diameter of 10 nm, can be easily obtained from the disaggregation of the TiO{sub 2} NT-bundles by combining the electrochemical process with the physical processing. Furthermore, the individual TiO{sub 2} NT powders exhibit higher photocatalytic activity than the TiO{sub 2} NT-bundle powders.

36 MATERIALS SCIENCE↗

Information Management Workflow and Tools Enabling Multiscale Modeling Within ICME Paradigm

With the increased emphasis on reducing the cost and time to market of new materials, the need for analytical tools that enable the virtual design and optimization of materials throughout their processing - internal structure - property - performance envelope, along with the capturing and storing of the associated material and model information across its lifecycle, has become critical. This need is also fueled by the demands for higher efficiency in material testing; consistency, quality and traceability of data; product design; engineering analysis; as well as control of access to proprietary or sensitive information. Fortunately, material information management systems and physics-based multiscale modeling methods have kept pace with the growing user demands. Herein, recent efforts to establish workflow for and demonstrate a unique set of web application tools for linking NASA GRC's Integrated Computational Materials Engineering (ICME) Granta MI database schema and NASA GRC's Integrated multiscale Micromechanics Analysis Code (ImMAC) software toolset are presented. The goal is to enable seamless coupling between both test data and simulation data, which is captured and tracked automatically within Granta MI®, with full model pedigree information. These tools, and this type of linkage, are foundational to realizing the full potential of ICME, in which materials processing, microstructure, properties, and performance are coupled to enable application-driven design and optimization of materials and structures.

Materials Engineering↗

Structural Modifications And Mechanical Degradation Of Ion Irradiated Glassy Polymer Carbon

The TRISO fuel has been used in some of the Generation IV nuclear reactor designs. It consists of a fuel kernel of UOx coated with several layers of materials with different functions. Pyrolytic carbon (PyC) is one of the materials in the layers. In this study we investigate the possibility of using Glassy Polymeric Carbon (GPC) as an alternative to PyC. GPC is used for artificial heart valves, heat-exchangers, and other high-tech products developed for the space and medical industries. This lightweight material can maintain dimensional and chemical stability in adverse environment and very high temperatures (up to 3000 deg. C). In this work, we are comparing the changes in physical and microstructure properties of GPC after exposure to irradiation fluence of 5 MeV Ag equivalent to a 1 displacement per atom (dpa) at samples prepared at 1000, 1500 and 2000 deg. C. The GPC material is manufactured and tested at the Center for Irradiation Materials (CIM) at Alabama A and M University. Transmission electron microscopy (TEM) and Raman spectroscopy were used for analysis.

36 MATERIALS SCIENCE↗

Microstructural and optical studies on sonochemically synthesized Cu doped ZnO nanoparticles

Copper doped ZnO nanoparticles were synthesized by sonochemical method varying the concentration of the impurity. Systematic investigations like X-ray diffraction (XRD) and Transmission electron microscopy (TEM) were carried out to understand the microstructural properties. The average particle sizes and all the crystallographic parameters were calculated from XRD results. This shows the formation of wurtzite phase of ZnO with average size of the particles as 53 nm and an increase of particle size with dopant concentration was also been observed. UV absorption and Fourier transformed infrared spectroscopy (FTIR) spectra revealed the absorption at wavelength < 370 nm with a remarkable red shift of absorption band and a linear decrease of transmittance with increase in doping concentrations respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗