Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Effect of Microstructure and Properties of Ni-WC Composite Coatings on Their Solid Particle Erosion Behavior

Metal matrix composites (MMCs) of WC in Co or Ni matrices are widely used due to their high wear resistance. Previous studies showed that tailoring the mechanical properties through optimum WC content can significantly extend the life cycle of MMCs. In this study, composite coatings of Ni with various WC content ranging from 10 to 55 vol.% were cold sprayed using agglomerated WCNi powders and two different sizes of Ni powders, − 10 + 4 (d{sub 50} = 7 µm) referred to as Ni(7) and − 35 + 15 (d{sub 50} = 25 µm) to as Ni(25). Microstructural characterization, including the deformed structure of Ni splats and retention and distribution of WC, was performed by scanning electron microscopy (SEM). Composite coatings were subjected to solid particle erosion following ASTM G76-13 standard. At low WC content coatings, erosion occurred primarily by plastic deformation of Ni matrices and knocking out of WC particles. At high WC concentrations, network distribution of compacted WCNi particles in the matrices led to a significant drop in erosion rates of coatings, due to a change in erosion mechanism from severe cutting and plowing of Ni and WC dislodging to WCNi splats spalling. Composite coatings sprayed using finer size Ni powder were usually more erosion resistant.

36 MATERIALS SCIENCE↗

Creep behavior of an additively manufactured 9Cr steel in the as-built condition

Limited studies have evaluated the creep behavior of additively manufactured (AM) ferritic-martensitic (FM) steels. This work investigated the creep behavior of a 9Cr FM steel fabricated by powder blown directed energy deposition (DED) technique. Here, the creep testing at 550–650 °C and 150 MPa for the specimens along the deposition direction in the as-built condition, together with corresponding microstructural characterization, revealed a threshold temperature between 600 and 625 °C, below which the steel has creep resistance comparable with Grade 91 cross-welds and noticeably greater than 9Cr-1Mo steel. The threshold temperature distinguishes the creep behavior in two regimes differentiated in creep activation energy, creep deformation, and failure mechanism. Unlike the creep rupture surface ~45° from the loading direction when tested above the threshold temperature, the creep rupture for testing below the threshold temperature resembles type IV failure in the cross-welds of ferritic steels. The DED-induced layer structure in the as-built steel played a significant role on the change of creep behavior.

36 MATERIALS SCIENCE↗

Synthesis, Characterization, and Testing of High-Lithium-Density Composite Breeders

Solid tritium breeder materials must first and foremost have sufficiently high concentrations of lithium to enable a plant-scale tritium breeding ratio greater than 1:1. However, in addition to lithium content, such breeder materials must also meet other performance metrics including high tritium release rates, thermal conductivities, and irradiation damage tolerance. Perhaps most importantly, tritium breeders must maintain their mechanical integrity during reactor operation so as to avoid degradation which can jeopardize the functionality of the tritium breeder blanket module, which in most designs takes the form of a pebble bed geometry. Unfortunately, the mechanical robustness of most lithium-bearing ceramics under investigation for fusion applications is often inversely related to the lithium atom density. For example, a material such as lithium oxide (Li2O), which has one of the highest lithium atom densities, has a much lower mechanical splitting strength than lithium metatitanate (Li2TiO3), though Li2TiO3 has less than half the lithium atom density of Li2O. This work seeks to provide an alternative to monolithic ceramic tritium breeders, in the form of metal-reinforced composite tritium breeders. Specifically, composite tritium breeders have been synthesized combining Li2O with various ferrous metal reinforcements via electric field assisted sintering (EFAS), also known as spark plasma sintering (SPS). As the metal reinforcement content is increased, metallic networks are observed, via electron microscopy and X-ray computed tomography, to form throughout the composite material. Through destructive mechanical testing, even dilute metal reinforcement loading enables drastic mechanical strength improvements over pure Li2O while higher loadings give rise to quasi-ductile behavior and higher ultimate strengths than Li2TiO3 – while still maintaining a higher density of lithium atoms than Li2TiO3 and many other breeder candidates. In addition to microstructural characterization and mechanical testing, thermal property measurements and hydrogen permeability testing are underway to further assess the suitability of such composites for fusion reactor applications.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effect of TiO{sub 2} nano fillers on the electrical conductivity of PSAN/TiO{sub 2} polymer nanocomposites

The microstructural characterization of Polystyrene co-acrylonitrile and Titanium dioxide (PSAN/TiO{sub 2}) nanocomposites has been performed by Positron Annihilation Lifetime Spectroscopy. The decrease of positron lifetime parameters viz. o-Ps lifetime (τ{sub 3}) and free volume size (V{sub f}) up to 0.6 wt% of TiO{sub 2} is attributed to the filling of free volume holes by TiO{sub 2} nanoparticles. The increased free volume size (V{sub f}) after 0.6 wt% of TiO{sub 2} indicates the formation of interface due to TiO{sub 2} nanoclusters. The variation of electrical conductivity at the lower and higher concentration of TiO{sub 2} in (PSAN/TiO{sub 2}) nanocomposites is attributed to the blocking effect and space charge effect respectively.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

High-temperature strengthening mechanisms of Laves and B2 precipitates in a novel ferritic alloy

Precipitates of the Laves and B2 phases were engineered in a newly-designed advanced ferritic alloy. Under creep test at 650 °C with 120 MPa, the material showed a steady-state minimum creep rate of 1 × 10 –4 h –1 , about one order of magnitude lower than T91. Microstructural characterization of the ferritic alloy revealed primarily ductile and partially brittle fractures after the creep test. Coarse Laves phase (~ 1 µm) was observed associating with the brittle fracture, resulting in reduced creep ductility. However, fine Laves phase precipitates (~ 100 nm) helped the dimple-ductile fracture and strengthened the material through impeding the motion of dislocations and boundaries. Unlike the B2 precipitates remained coherent exerting the classic Orowan bypassing mechanism at the brittle location, some of the B2 precipitates at the ductile location became incoherent and can develop an attractive interaction with dislocations. In conclusion, this coherency change of B2 precipitates, together with the nucleation of ultrafine (~ 40 nm) Laves phase precipitates during the creep test, would compensate for the coarsening-induced loss of Orowan strengthening of coherent B2 precipitates.

36 MATERIALS SCIENCE↗

Nano-modification to improve the ductility of cementitious composites

Effect of nano-sized mineral additions on ductility of engineered cementitious composites (ECC) containing high volumes of fly ash was investigated at different hydration degrees. Various properties of ECC mixtures with different mineral additions were compared in terms of microstructural properties of matrix, fiber-matrix interface, and fiber surface to assess improvements in ductility. Microstructural characterization was made by measuring pore size distributions through mercury intrusion porosimetry (MIP). Hydration characteristics were assessed using thermogravimetric analysis/differential thermal analysis (TGA/DTA), and fiber-matrix interface and fiber surface characteristics were assessed using scanning electron microscopy (SEM) through a period of 90 days. Moreover, compressive and flexural strength developments were monitored for the same period. Test results confirmed that mineral additions could significantly improve both flexural strength and ductility of ECC, especially at early ages. Cheaper Nano-CaCO{sub 3} was more effective compared to nano-silica. However, the crystal structure of CaCO{sub 3} played a very important role in the range of expected improvements.

36 MATERIALS SCIENCE↗

In situ high-temperature X-ray diffraction study of Sc-doped titanium oxide nanocrystallites

Titanium dioxide is an inexpensive wide-gap highly ionic semiconductor with striking photocatalytic capabilities in several heterogeneous photoredox reactions. A small crystal size is desirable to maximize the surface area, since photocatalytic reactions occur at the surface of a photocatalyst. Presented in this work are the synthesis and microstructural characterization of 4 at.% Sc-doped TiO 2 (4SDT) prepared by water-based co-precipitation. The crystal structure of 4SDT was examined via in situ high-temperature powder X-ray diffraction experiments from 25 to 1200°C. Rietveld analysis revealed single-phase anatase up to 875°C, while at 900°C the anatase-to-rutile phase transformation occurred and at higher temperatures additional reflections of Sc-rich phases (Sc 2 TiO 5 from 975°C and Ti 3 Sc 4 O 12 or Sc 2 O 3 at 1200°C) were observed. Debye function analysis (DFA) was applied to model the total scattering pattern directly in reciprocal space, allowing the reconstruction of Ti vacancies. Both Rietveld and DFA methods were applied to estimate the nanocrystallite size and shape with consistent growth in crystallite size with temperature: an ellipsoid shape with equatorial ~4.7 nm / axial (001) ~6.9 nm at 25°C to equatorial ~27.9 nm / axial (001) ~39.6 nm at 900°C refined by Rietveld analysis, versus a cylinder shape with D a , b = 4.3 nm and size dispersion σ ab = 1.5 nm, L c = 4.9 nm and σ c = 2.3 nm at 25°C to D a , b = 21.4 nm, σ ab = 8.3 nm, L c = 23.9 and σ c = 10.9 nm at 900°C estimated by DFA. The microstructural changes obtained by Rietveld and DFA methods were supported by high-resolution transmission electron microscopy image analysis, as well as by the less direct nitrogen sorption techniques that provide information on the size of non-agglomerated and dense particles. The Ti site-occupancy factor showed a linear increase from 0.6–0.8 at 25°C to unity at 900°C for anatase, and from ~0.7 at 900°C to unity at 1200°C for rutile, via Rietveld analysis and DFA.

36 MATERIALS SCIENCE↗

Electrochemical Behavior of HVOF-Sprayed Amorphous and Nanocrystalline Fe-Based Fe{sub 73.13}Si{sub 11.12}B{sub 10.79}Cr{sub 2.24}C{sub 2.72} Composite Coatings

The present work describes a series of new amorphous and nanocrystalline composite coatings (composition: 87.6% Fe, 6.7% Si, 2.5% B, 2.5% Cr, 0.7% C in wt.%) on a mild steel substrate made by high-velocity oxy-fuel thermal spray at different feed rates of 20, 30 and 40 g/min. The microstructure characterization using scanning electron microscopy coupled with energy-dispersive spectroscopy shows uniform and adherent coatings of different thickness depending on the feed rate. The structure of the coating is composite in nature (mixture of amorphous and nanocrystalline phases) as confirmed by the x-ray diffraction and transmission electron microscopy. The hardness of the coating is almost 6-7 times than that of the substrate. Though polarization test of the coating demonstrates corrosion resistance in 3.5% NaCl solution similar to the substrate, the difference of corrosion potentials of the coatings and the substrate is largely negative (~ more than 200 mV against saturated calomel electrode) suggesting anodic nature of the coating as compared to the substrate resulting in sacrificial effect.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effects of Coatings on the High-Cycle Fatigue Life of Threaded Steel Samples

In this work, high-cycle fatigue is studied for threaded cylindrical high-strength steel samples coated using three different industrial processes: black oxidation, normal-temperature galvanization and high-temperature galvanization. The fatigue performance in air is compared with that of uncoated samples. Microstructural characterization revealed the abundant presence of small cracks in the zinc coating partially penetrating into the steel. This is consistent with the observation of multiple crack initiation sites along the thread in the galvanized samples, which led to crescent type fracture surfaces governed by circumferential growth. In contrast, the black oxidized and uncoated samples exhibited a semicircular segment type fracture surface governed by single-sided growth with a significantly longer fatigue life. Numerical fatigue life prediction based on an extended Paris-law formulation has been conducted on two different fracture cases: 2D axisymmetric multisided crack growth and 3D single-sided crack growth. The results of this upper-bound and lower-bound approach are in good agreement with experimental data and can potentially be used to predict the lifetime of bolted components.

36 MATERIALS SCIENCE↗

Interfacial Microstructure and Mechanical Properties of Friction Stir Welded Joints of Commercially Pure Aluminum and 304 Stainless Steel

In the present investigation, friction stir welding of commercially pure aluminum and 304 stainless steel was carried out at varying tool rotational speeds from 200 to 1000 rpm in steps of 200 rpm using 60 mm/min traverse speed at 2 (degree) tool tilt angle. Microstructural characterization of the interfacial zone was carried out using optical microscope and scanning electron microscope. Energy-dispersive spectroscopy indicated the presence of FeAl{sub 3} intermetallic phase. Thickness of the intermetallic layer increased with the increase in tool rotational speed. X-ray diffraction studies indicated the formation of intermetallic phases like FeAl{sub 2}, Fe{sub 4}Al{sub 13}, Fe{sub 2}Al{sub 5}, and FeAl{sub 3}. A maximum tensile strength of ~ 90% that of aluminum along with ~ 4.5% elongation was achieved with the welded sample at tool rotational speed of 400 rpm. The stir zone showed higher hardness as compared to base metals, heat affected zone, and thermo-mechanically affected zone due to the presence of intermetallics. The maximum hardness value at the stir zone was achieved at 1000 rpm tool rotational speed.

36 MATERIALS SCIENCE↗

Ab Initio Analysis of Guinier–Preston–Bagaryatsky Zone Nucleation in Al-Cu-Mg Alloys

Due to the inherit difficulties associated with microstructure characterization in the early stages of aging, the origin of rapid hardening in Al-Cu-Mg alloys remains a poorly understood and controversial issue. This works addresses the precipitation processes in the early stages by ab-initiomodeling of GPB zone nucleation. We derive the structural nature of GPB zone nuclei and establish that the nucleation starts with 1D-GPB1 crystals, which represent thermodynamically stable configurations at the size scale previously associated only with solute clusters. It is also established that the 1D-GPB1 can form very rapidly due a simple structural transition from FCC based configurations (clusters). The formation of GPB zones in the early stages of aging is validated by comparison with previous experimental measurements. Based on previous experimental evidence, it is postulated that GPB zones rather than solute clusters may be able to rationalize the rapid hardening in the Al-Cu-Mg alloys.

36 MATERIALS SCIENCE↗

Mapping 3D grain and precipitate structure during in situ mechanical testing of open-cell metal foam using micro-computed tomography and high-energy X-ray diffraction microscopy

Open-cell metal foams are ultra-low-density cellular metals with complex hierarchical structures that span bulk, cell, ligament, and sub-ligament scales and give rise to desirable properties such as high strength-to-weight ratio and excellent energy absorption. Although literature suggests that intrinsic material structures at sub-ligament length scales (e.g., grains and precipitates) play an important role in mechanical behavior of open-cell metal foams, there are very few experimental measurements of such structures in three dimensions and for meaningful volumes of foam. This study seeks to map and track the three-dimensional (3D) grain and precipitate structures of an intact volume of open-cell aluminum foam by advancing microstructural characterization techniques that leverage X-ray micro-computed tomography (μCT) and far-field high-energy X-ray diffraction microscopy (FF-HEDM). A 6%-relative-density aluminum foam sample was mechanically tested in compression while μCT and FF-HEDM measurements were collected at interrupted loading states at beamline 1-ID of the Advanced Photon Source. Further, a new scanning strategy and reconstruction algorithm were established to enable characterization of a foam volume with diameter approximately four times wider than the nominal width of the X-ray beam. The result is a set of maps that detail both the 3D grain and precipitate structures throughout the foam volume at successive strain steps. A novel grain tracking procedure was developed to track individual grains within the foam volume by accounting for the large rigid-body motions that individual ligaments can undergo during mechanical loading. The ability to track grains and precipitate structures in three dimensions throughout large bulk deformation of ultra-low-density polycrystalline materials enables new possibilities for validating numerical models and investigating local failure mechanisms. Furthermore, the methods and procedures developed in this study could be applied to other ultra-low-density structures, such as additively manufactured lattices.

36 MATERIALS SCIENCE↗

Microstructures and deformation mechanisms of Cr26Mn20Fe20Co20Ni14 alloys

Highlights: • The single-phase FCC alloy as the annealing temperature exceeding 1015 °C • The dual-phase structure as the annealing temperature lower than 1000 °C • The σ phases grow primarily at grain boundaries. • The single-phase alloy deforms via dislocations and twins. • In-situ tensile experiment reveals twinning at the crack tip. - Abstract: We investigated microstructures and tension properties of Cr{sub 26}Mn{sub 20}Fe{sub 20}Co{sub 20}Ni{sub 14} alloys that were produced by arc-melting and subsequent thermal-mechanical processing—hot-rolling → cold-rolling → annealing at different temperatures ranging from 500 °C to 1100 °C for 1 h → air cooling. Microstructure characterization shows the single-phase solid solution with face centered cubic structure as the annealing temperature exceeding 1015 °C while the dual-phase structure (Cr-rich σ phase and FCC solid solution) as the annealing temperature lower than 1000 °C. The σ phases grow primarily at grain boundaries and act as precipitation strengthening units to enhance strain hardening rate. The single-phase solid solution deforms plastically via dislocations and twins. Twin boundaries associated with deformation twinning impede dislocation motion, enhancing the strain hardening capacity. In-situ tensile experiment in transmission electron microscope further reveals that twinning occurs at the crack tip and facilitates the deflection of crack propagation towards twinning shear direction. This work implies that a strength-ductility combination can be realized by coupling precipitation strengthening and twinning-induced plasticity in multiple principle elements alloys.

36 MATERIALS SCIENCE↗

Effect of Co on twin formation and magnetic properties of Sm(Fe,Ti,V) 12 alloys

Transferring the excellent intrinsic magnetic properties of SmFe 12 -based compounds to their extrinsic properties remains the main challenge in the development of high-performance SmFe12-based permanent magnets. Twin formation is one of the reasons for the inability to achieve high coercivity and remanence. Here we have shown that the addition of Co in Sm(Fe 1-x Co x ) 10–11 M 1–2 alloys, where M=Ti and V, leads to an increase in twin density. Microstructural characterizations revealed that the atomic arrangement in the twin boundary changes depending on the stabilizing element, which directly influences the local intrinsic magnetic properties. Theoretical investigations showed that the critical grain size at which twin formation can be hindered by grain size reduction decreases when the stabilizer changes from V to Ti. Furthermore, this study shows that the alloy composition influences not only the intrinsic magnetic properties but also the twin formation energy and its grain size dependence, crucial for the design of SmFe12-based permanent magnets.

36 MATERIALS SCIENCE↗

TEM investigations on lath martensite substructure in quenched Fe-0.2C alloys

Highlights: • Twin can be lath martensite substructure in low-carbon steels. • Detwinning behavior occurs in an auto-tempering process during quenching. • Detwinning may result in the formation of twinned laths. • Detwinning may result in the laths with dislocation-like contrast as substructure. - Abstract: Lath martensite in low-carbon steels is the main microstructural feature in the quenched state, and dislocations have been generally recognized as the substructure of lath martensite. However, the effects of quenching conditions on the quenched substructure have not yet been fully understood. In the present work, a Fe-0.2C (wt%) alloy was selected for detailed investigations on the microstructural evolution at various austenitizing temperatures. Microstructural characterization was carried out by using a conventional transmission electron microscope (TEM). The substructure of lath martensite was found to vary with austenitizing temperature. In the 1200 °C-water-quenched (WQ) samples, twinned laths (two specific variants having a {112}<111>-type twin relationship) and a twinned region (laths with the twin structure as their substructure) can be observed. Almost all lath martensite with a high density of fine twins as its substructure can be obtained in the 1300 °C-WQ samples. The twins gradually disappear or detwinning-occurs during TEM observations carried out with in situ heating. A further increase in temperature results in the formation of twinned laths and then lath with dislocation-like contrasts or lines appears as the substructure. These results suggested that a completely twin structure can be the initial substructure of lath martensite, and lath with dislocation-like contrasts or lines as its substructure is most likely the auto-tempering result of twinning.

36 MATERIALS SCIENCE↗

Laves phase in alloy 718 fusion zone — microscopic and calorimetric studies

Microstructural characterization of alloy 718 fusion zone welded with both solid solution and age hardenable filler metal has been done. The microsegregation and the aging response were studied by employing three levels of weld cooling rate. Gas Tungsten Arc welding process was used. The fusion zone of solid solution filler metal has been responding to the aging treatment due to the weld process conditions and weld metal chemistry. However the weld metal composition was modified due to the higher molybdenum (Mo) content in solid solution filler metal. The effect of this modification on the phase reaction temperatures was studied and the same was compared with the conventional filler metal. - Graphical abstract: Display Omitted - Highlights: • Interdendritic segregation has been controlled by weld cooling rate. • Laves phase formation has been studied with cooling rate and weld metal chemistry. • Aging response with solid solution filler metal has been demonstrated. • Reduction in Laves phase and alloying element segregation has been confirmed. • Reaction temperatures were found modified because of Mo addition.

36 MATERIALS SCIENCE↗

Analysis of Phase Transformation Studies in Solute Addition Alloys

Components serving in a nuclear reactor plant must withstand a very harsh environment including extended time at elevated temperatures, neutron irradiation, stress, and/or corrosive media. The many modes of degradation are complex and very depending on material and service locations. However, understanding and managing materials degradation is paramount for the continued safe and reliable operation of nuclear power plants. For the reactor core and primary systems, several key areas have been identified. Thermomechanical considerations such as aging and fatigue must be examined. Irradiation-induced processes must also be considered for higher fluences under the life extension consideration of the current light water reactors (LWRs), which particularly includes the influence of radiation-induced segregation (RIS), swelling, and precipitation on component hardening and embrittlement. Corrosion takes many forms within the reactor core, although irradiation-assisted stress corrosion cracking (IASCC) and primary water stress corrosion cracking (PWSCC) are of high interest in extended life scenarios. Research in these areas can build upon other ongoing programs in the LWR industry as well as other reactor materials programs (such as fusion and fast reactors) to help resolve these issues for extended LWR life. Type 304 and 316 stainless steels are classic structural materials used in LWRs. A set of well designed type 304 and 316 variants by changing the amount of a single solute element were irradiated using the BOR-60 fast breeder reactor at ~320°C in Russia. This set of alloy samples has been used in this task to characterize detailed microstructural evolution and measure magnetic phase, swelling and hardness. This report summarizes the detailed microstructural results, characterized using conventional and scanning transmission electron microscopy (CTEM/STEM) and energy dispersive X-ray spectroscopy (EDS), and the newly developed model of strength factor for estimating radiation hardening. The results provide invaluable insights into understanding degradation mechanisms of key components and assists in the prediction of the life of similar materials and the base knowledge required to develop advanced radiation resistant alloys. The effect of solute elements on microstructural evolution under neutron irradiation is explored. The approximate correlation between microstructure changes and radiation hardening is established. The major results and implications are discussed below.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

X-ray diffraction and surface acoustic wave analysis of BST/Pt/TiO{sub 2}/SiO{sub 2}/Si thin films

High dielectric constant and electrostriction property of (Ba, Sr)Ti0{sub 3} (BST) thin films result in an increasing interest for dielectric devices and microwave acoustic resonator. Barium strontium titanate (Ba{sub 0.645}Sr{sub 0.355}TiO{sub 3}) films of about 300 nm thickness are grown on Pt(111)/TiO{sub 2}/SiO{sub 2}/Si(001) substrates by rf magnetron sputtering deposition techniques. X-ray diffraction is applied for the microstructural characterization. The BST films exhibit a cubic perovskite structure with a dense and smooth surface. A laser acoustic waves (LA-waves) technique is used to generate surface acoustic waves (SAW) propagating in the BST films. Young's modulus E and the Poisson ratio {nu} of TiO{sub 2,} Pt and BST films in different propagation directions are derived from the measured dispersion curves. Estimation of BST elastics constants are served in SAW studies. Impact of stratification process on SAW, propagating along [100] and [110] directions of silicon substrate, has been interpreted on the basis of ordinary differential equation (ODE) and stiffness matrix method (SMM). A good agreement is observed between experimental and calculated dispersion curves. The performed calculations are strongly related to the implemented crystallographic data of each layer. Dispersion curves are found to be sensitive to the SAW propagation direction and the stratification process for the explored frequency ranges 50-250 MHz, even though it corresponds to a wave length clearly higher than the whole films thickness.

36 MATERIALS SCIENCE↗