Search NASA⌕ Search

SEARCH · Search NASA

Results for “parameter selection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Description and theory of operation of the computer by-pass system for the NASA F-8 digital fly-by-wire control system

A triplex digital flight control system was installed in a NASA F-8C airplane to provide fail operate, full authority control. The triplex digital computers and interface circuitry process the pilot commands and aircraft motion feedback parameters according to the selected control laws, and they output the surface commands as an analog signal to the servoelectronics for position control of the aircraft's power actuators. The system and theory of operation of the computer by pass and servoelectronics are described and an automated ground test for each axis is included.

Source record↗
NASA NTRS1977

Aerodynamic performance of conventional and advanced design labyrinth seals with solid-smooth abradable, and honeycomb lands

Labyrinth air seal static and dynamic performance was evaluated using solid, abradable, and honeycomb lands with standard and advanced seal designs. The effects on leakage of land surface roughness, abradable land porosity, rub grooves in abradable lands, and honeycomb land cell size and depth were studied using a standard labyrinth seal. The effects of rotation on the optimum seal knife pitch were also investigated. Selected geometric and aerodynamic parameters for an advanced seal design were evaluated to derive an optimized performance configuration. The rotational energy requirements were also measured to determine the inherent friction and pumping energy absorbed by the various seal knife and land configurations tested in order to properly assess the net seal system performance level. Results indicate that: (1) seal leakage can be significantly affected with honeycomb or abradable lands; (2) rotational energy absorption does not vary significantly with the use of a solid-smooth, an abradable, or a honeycomb land; and (3) optimization of an advanced lab seal design produced a configuration that had leakage 25% below a conventional stepped seal.

Stocker, H. L.↗
NASA NTRS1978

The SEASAT-A synthetic aperture radar design and implementation

The SEASAT-A synthetic aperture imaging radar system is the first imaging radar system intended to be used as a scientific instrument designed for orbital use. The requirement of the radar system is to generate continuous radar imagery with a 100 kilometer swath with 25 meter resolution from an orbital altitude of 800 kilometers. These requirements impose unique system design problems and a description of the implementation is given. The end-to-end system is described, including interactions of the spacecraft, antenna, sensor, telemetry link, recording subsystem, and data processor. Some of the factors leading to the selection of critical system parameters are listed. The expected error sources leading to degradation of image quality are reported as well as estimate given of the expected performance from data obtained during a ground testing of the completed subsystems.

Jordan, R. L.↗
NASA NTRS1979

Updating the limit efficiency of silicon solar cells

Evaluation of the limit efficiency based on the simplest, most basic mathematical method that is appropriate for the conditions imposed by the cell model is discussed. The methodology, the solar cell structure, and the selection of the material parameters used in the evaluation are described. The results are discussed including a set of design goals derived from the limit efficiency.

Wolf, M.↗
NASA NTRS1978

A design point correlation for losses due to part-span dampers on transonic rotors

The design-point losses caused by part-span dampers were correlated for 21 transonic axial-flow fan rotors that had tip speeds varying from 350 to 488 meters per second and design pressure ratios of 1.5 to 2.0. The additional loss attributable to the damper and the total region along the blade height influenced were correlated with selected aerodynamic and geometric parameters. The maximum damper loss correlated well with the mean inlet Mach number at the damper location, the geometric parameters of leading- and trailing-edge damper radius normalized by mean passage height and damper aerodynamic chord, respectively, and the aerodynamic loading parameter of the blade camber divided by the solidity at the damper location. The region of damper influence extended over a mean passage height of the order of 10 to 15 times the maximum damper thickness.

Roberts, W. B.↗
NASA NTRS1978

The Seasat-A synthetic aperture radar design and implementation

The Seasat-A Synthetic Aperture Imaging Radar System is the first imaging radar system intended to be used as a scientific instrument designed for orbital use. The requirement of the radar system is to generate continuous radar imagery with a 100 kilometer swath with 25 meter resolution from an orbital altitude of 800 kilometers. These requirements impose unique system design problems and a description of the implementation will be given. The end-to-end data system will be described, including interactions of the spacecraft, antenna, sensor, telemetry link, recording subsystem, and data processor. Some of the factors leading to the selection of critical system parameters will be listed. The expected error sources leading to degradation of image quality will be described as well as estimates given of the expected performance from data obtained during ground testing of the completed subsystems.

Jordan, R.↗
NASA NTRS1981

Investigations of medium wavelength magnetic anomalies in the eastern Pacific using MAGSAT data

The suitability of using magnetic field measurements obtained by MAGSAT is discussed with regard to resolving the medium wavelength anomaly problem. A procedure for removing the external field component from the measured field is outlined. Various methods of determining crustal magnetizations are examined in light of satellite orbital parameters resulting in the selection of the equivalent source technique for evaluating scalar measurements. A matrix inversion of the vector components is suggested as a method for arriving at a scalar potential representation of the field.

Harrison, C. G. A.↗
NASA NTRS1982

A concept for a fuel efficient flight planning aid for general aviation

A core equation for estimation of fuel burn from path profile data was developed. This equation was used as a necessary ingredient in a dynamic program to define a fuel efficient flight path. The resultant algorithm is oriented toward use by general aviation. The pilot provides a description of the desired ground track, standard aircraft parameters, and weather at selected waypoints. The algorithm then derives the fuel efficient altitudes and velocities at the waypoints.

Collins, B. P.↗
NASA NTRS1981

Data base manipulation for assessment of multiresource suitability and land change

Progress is reported in three tasks which support the overall objectives of renewable resources inventory task of the AgRISTARS program. In the first task, the geometric correction algorithms of the Master Data Processor were investigated to determine the utility of data corrected by this processor for U.S. Forest Service uses. The second task involved investigation of logic to form blobs as a precursor step to automatic change detection involving two dates of LANDSAT data. Some routine procedures for selecting BLOB (spatial averaging) parameters were developed. In the third task, a major effort was made to develop land suitability modeling approches for timber, grazing, and wildlife habitat in support of resource planning efforts on the San Juan National Forest.

Colwell, J.↗
NASA NTRS1981

General purpose research rotor

An analytical study, under a NASA contract, is performed on an advanced flight research rotor (four-bladed, 54 ft in diameter, with bearingless rotor retention characteristics) to determine the sensitivity of total rotor characteristics such as vibratory hub loads, rotor horsepower, and blade loads, to parametric variability of the rotor configuration. The sensitivity of the rotor to various combinations of blade planform taper, percent of blade span that is tapered, tip sweep angle, built-in-twist, and torsional frequency is determined for specific configurations by randomly selecting combinations of these parameters. Characteristics of other intermediate rotor configurations are determined by a regression analysis. The results show that a wide range of rotor total performance characteristics can be obtained for a rotor trimmed to the same flight conditions. The regression equations predict total performance of the rotor very well and appear to be a useful analytical tool for rotor design optimization. Figures showing the results of the various tests are given along with a table of the regression coefficients.

Jones, R.↗
NASA NTRS1983

Optimal design of a passive vibration absorber for a truss beam

The selection of the design parameters of passive vibration absorbers attached to a long cantilevered beam is studied. This study was motivated by the need for conducting parametric analysis of dynamics and control for Space-Shuttle-attached long beams. An optimization scheme using a quadratic cost function is introduced yielding the optimal sizing of the tip vibration absorber. Analytical solutions for an optimal absorber are presented for the case of one beam vibrational mode coupled with the absorber dynamics, and results are extended to cover the multiple mode case. An algorithm is developed to make an initial estimate of optimal tuning parameters which minimize the quadratic error cost function. Examples are given to illustrate the design concept.

Juang, J.-N.↗
NASA NTRS1983

Parametric tip effects for conformable rotor applications

A research study was initiated to systematically determine the impact of selected blade tip geometric parameters on aeroelasticity conformable rotor performance and loads characteristics. The model articulated rotors included baseline and torsionally soft blades with interchangeable tips. Seven blade tip designs were evaluated on the baseline rotor and three tip designs were tested on the torsionally soft blades. The designs incorporated a systematic variation in three geometric parameters: sweep, taper, and anhedral. The rotors were evaluated in the NASA Langley Transonic Dynamics Tunnel at several advance ratios, lift and propulsive force values, and tip Mach numbers. Based on the test results, tip parameter variations generated significant rotor performance and loads difference for both baseline and torsionally soft blades. Azimuthal variation of elastic twist generated by the tip parameters strongly correlated with rotor performance and loads, but the magnitude of advancing blade elastic twist did not correlate.

Mantay, W. R.↗
NASA NTRS1984

Regions of attraction and ultimate boundedness for linear quadratic regulators with nonlinearities

The closed-loop stability of multivariable linear time-invariant systems controlled by optimal linear quadratic (LQ) regulators is investigated for the case when the feedback loops have nonlinearities N(sigma) that violate the standard stability condition, sigma N(sigma) or = 0.5 sigma(2). The violations of the condition are assumed to occur either (1) for values of sigma away from the origin (sigma = 0) or (2) for values of sigma in a neighborhood of the origin. It is proved that there exists a region of attraction for case (1) and a region of ultimate boundedness for case (2), and estimates are obtained for these regions. The results provide methods for selecting the performance function parameters to design LQ regulators with better tolerance to nonlinearities. The results are demonstrated by application to the problem of attitude and vibration control of a large, flexible space antenna in the presence of actuator nonlinearities.

Joshi, S. M.↗
NASA NTRS1985

Modeling a Transient Catalytic Combustor

Transient model of monolith catalytic combustor presented in report done under NASA/DOE contract. Model assumes quasi-steady gas phase and thermally "thin" solid. In gas-phase treatment, several quasi-global chemical reactions assumed capable of describing CO and unburnt hydrocarbon emissions in fuel-lean operations. In steady-state computation presented, influence of selected operating and design parameters on minimum combustor length studied. When fast transient responses required, both steady and unsteady studies made to achieve meaningful compromise in design.

Tien, J. S.↗
NASA NTRS1984

A Very Efficient Transfer Function Bounding Technique on Bit Error Rate for Viterbi Decoded, Rate 1/N Convolutional Codes

For rate 1/N convolutional codes, a recursive algorithm for finding the transfer function bound on bit error rate (BER) at the output of a Viterbi decoder is described. This technique is very fast and requires very little storage since all the unnecessary operations are eliminated. Using this technique, we find and plot bounds on the BER performance of known codes of rate 1/2 with K 18, rate 1/3 with K 14. When more than one reported code with the same parameter is known, we select the code that minimizes the required signal to noise ratio for a desired bit error rate of 0.000001. This criterion of determining goodness of a code had previously been found to be more useful than the maximum free distance criterion and was used in the code search procedures of very short constraint length codes. This very efficient technique can also be used for searches of longer constraint length codes.

Lee, P. J.↗
NASA NTRS1985

Parameterization in Grid Generation

The distribution of grid points for calculating the solution of partial differential equations is chosen so as to include consideration of truncation error, stability, and the resolution of the solution near boundary layers and shocks. It is important to specify the distribution of points along a grid line. The problem of distributing points along a curve is considered. It is assumed that the curve is defined parametrically. The objective is to select a set of parameter values so that the corresponding points on the curves are properly distributed. The distribution is based on some intrinsic property of the curve such as arc length or curvature.

Mastin, C. W.↗
NASA NTRS1984

Estimation of regions of attraction and ultimate boundedness for multiloop LQ regulators

Closed-loop stability is investigated for multivariable linear time-invariant systems controlled by optimal full state feedback linear quadratic (LQ) regulators, with nonlinear gains present in the feedback channels. Estimates are obtained for the region of attraction when the nonlinearities escape the (0.5, infinity) sector in regions away from the origin and for the region of ultimate boundedness when the nonlinearities escape the sector near the origin. The expressions for these regions also provide methods for selecting the performance function parameters in order to obtain LQ designs with better tolerance for nonlinearities. The analytical results are illustrated by applying them to the problem of controlling the rigid-body pitch angle and elastic motion of a large, flexible space antenna.

Joshi, S. M.↗
NASA NTRS1985

A Parametric Study of the Ibrahim Time Domain Modal Identification Algorithm

The accuracy of the Ibrahim time Domain (ITD) identification algorithm in extracting structural model parameters from free response functions was studied using computer simulated data for 65 positions on an isotropic, uniform thickness plate with mode shapes obtained by NASTRAN analysis. Natural frequencies were used to study identification results over ranges of modal parameter values and user selectable algorithm constants. Effects of superimposing various levels of noise onto the functions were investigated. No detrimental effects were observed when the number of computational degrees of freedom allowed in the algorithm was made many times larger than the minimum necessary for adequate identification. The use of a high number of degrees of freedom when analyzing experimental data, for the simultaneous identification of many modes in one computer run are suggested.

Pappa, R. S.↗