Search NASA⌕ Search

SEARCH · Search NASA

Results for “reverse phasing system”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Structural and magnetic properties of the nanocomposite materials based on a mesoporous silicon dioxide matrix

The structural and magnetic properties of the mesoporous systems based on silicon dioxide with a regular hexagonal arrangement of pores several microns in length and several nanometers in diameter, which are filled with iron compound nanofilaments in various chemical states, are studied in detail. The studies are performed using the following mutually complementary methods: transmission electron microscopy, SQUID magnetometry, electron spin resonance, Mössbauer spectroscopy, polarized neutron small-angle diffraction, and synchrotron radiation diffraction. It is shown that the iron nanoparticles in pores are mainly in the γ phase of Fe{sub 2}O{sub 3} with a small addition of the α phase and atomic iron clusters. The effective magnetic field acting on a nanofilament from other nanofilaments is 11 mT and has a dipole nature, the ferromagnetic–paramagnetic transition temperature is in the range 76–94 K depending on the annealing temperature of the samples, and the temperature that corresponds to the change in the magnetic state of the iron oxide nanofilaments is T ≈ 50–60 K at H = 0 and T ≈ 80 K at H = 300 mT. It is also shown that the magnetization reversal of an array of nanofilaments is caused by the magnetostatic interaction between nanofilaments at the fields that are lower than the saturation field.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Exploring ENSO-Induced Anomalies over North America in Historical and Future Climate Simulations That Use HadGEM2-ESM Output to Drive WRF

Projected changes to the El Niño Southern Oscillation (ENSO) climate mode have been explored using global Earth system models (ESMs). Regional expressions of such changes have yet to be fully advanced and may require the use of regional downscaling. Here, we employ regional climate modeling (RCM) using the Weather Research and Forecasting (WRF) model at convection-permitting resolution and nested in output from the HadGEM2 ESM. We quantify ENSO teleconnections to temperature and precipitation anomalies in historical and future climate scenarios over eastern North America. Two paired simulations are run, a strong El Niño (positive ENSO phase) and a weak La Niña (negative ENSO phase), for the historical and future years. The HadGEM2 direct output and HadGEM2-WRF simulation output are compared to the anomalies derived from the NOAA ENSO Climate Normals dataset. The near-surface temperature and precipitation differences by ENSO phase, as represented by the HadGEM2-WRF historical simulations, show a poor degree of association with the NOAA ENSO Climate Normals, in part because of the large biases in the HadGEM2 model. Downscaling with the WRF model does improve the agreement with the observations, and large discrepancies remain. The model chain HadGEM2-WRF reverses the sign of the ENSO phase response over eastern North America under simulations of the future climate with high greenhouse gas forcing, but due to the poor agreement with the NOAA ENSO Climate Normals it is difficult to assign confidence to this prediction.

54 ENVIRONMENTAL SCIENCES↗

Perceived Conflicts of Systems Engineering in Early-Stage Research and Development 1

Early Systems Research and Development (ESR&D) is one of the most crucial phases in the product development process. It both blends and blurs the lines between science and engineering, and requires a risk-based, disciplined, and graded approach to effectively manage scope, cost, and complexity of the final product. Many leaders, program managers, and scientists are unwilling to involve systems engineering because of the perception that systems engineering is heavily process oriented, adds unnecessary costs, and should be applied only to mature technologies. The value of systems engineering as applied to ESR&D is unclear to these key individuals. The unfortunate result is that system engineering is not applied to ESR&D. This results in R&D efforts that may have solved the wrong problem, selected the wrong architecture, require technical rework, have difficulty transitioning later maturity levels, and result in higher R&D costs and extended development timelines. This work discusses the difficulty of introducing systems engineering to the research and early development process and their inclination perspectives of researchers, engineers, and managers. The article shall offer potential means to manage the cultural transformation of early adoption of right-sized systems engineering in ESR&D and reverse the attitudinal positions.

42 ENGINEERING↗

Dual quantum spin Hall insulator by density-tuned correlations in TaIrTe 4

The convergence of topology and correlations represents a highly coveted realm in the pursuit of new quantum states of matter. Introducing electron correlations to a quantum spin Hall (QSH) insulator can lead to the emergence of a fractional topological insulator and other exotic time-reversal-symmetric topological order, not possible in quantum Hall and Chern insulator systems. Here, in this study, we report a new dual QSH insulator within the intrinsic monolayer crystal of TaIrTe 4 , arising from the interplay of its single-particle topology and density-tuned electron correlations. At charge neutrality, monolayer TaIrTe 4 demonstrates the QSH insulator, manifesting enhanced nonlocal transport and quantized helical edge conductance. After introducing electrons from charge neutrality, TaIrTe 4 shows metallic behaviour in only a small range of charge densities but quickly goes into a new insulating state, entirely unexpected on the basis of the single-particle band structure of TaIrTe 4 . This insulating state could arise from a strong electronic instability near the van Hove singularities, probably leading to a charge density wave (CDW). Remarkably, within this correlated insulating gap, we observe a resurgence of the QSH state. The observation of helical edge conduction in a CDW gap could bridge spin physics and charge orders. The discovery of a dual QSH insulator introduces a new method for creating topological flat minibands through CDW superlattices, which offer a promising platform for exploring time-reversal-symmetric fractional phases and electromagnetism.

electronic devices↗

Local structure memory effects in the polar and nonpolar phases of MoTe 2

We use total scattering to study the reversible transition between the polar 1T' and nonpolar T d phases of layered MoTe 2 taking place at 240 K. Whereas, macroscopically, the transition appears to be first order, locally, it is not. In particular, a great deal of the stacking sequence of Te-Mo-Te layers characteristic of the polar 1T' phase persists locally in the nonpolar T d phase, and vice versa, over a broad temperature range extending about 100 K both below and above the transition. The intermixing ratio for the two sequences evolves gradually across the transition temperature, consistent with a second-order transition behavior. Here, the presence of coexisting local polar and nonpolar regions and the resulting variety of internal interfaces where the spatial inversion symmetry is broken may be behind some of the unusual electronic properties of T d –MoTe 2 , including its putative type-II Weyl semimetal state.

2-dimensional systems↗

Recent Advances in Colloidal and Interfacial Phenomena Involving Liquid Crystals

This feature article presents recent advances in several areas of research involving the interfacial ordering of liquid crystals (LCs). The initial advance revolves around the ordering of LCs at bio/chemically functionalized surfaces. Whereas the majority of past studies of surface-induced ordering of LCs have involved surfaces of solids that present a limited diversity of chemical functional groups (surfaces at which van der Waals forces dominate surface-induced ordering), recent studies have moved to investigate the ordering of LCs on chemically complex surfaces. For example, surfaces decorated with biomolecules (e.g., oligopeptides and proteins) and transition-metal ions have been investigated, leading to an understanding of the roles that metal-ligand coordination interactions, electrical double layers, acid-base interactions, and hydrogen bonding can play in the interfacial ordering of LCs. The opportunity to create chemically responsive LCs capable of undergoing ordering transitions in the presence of targeted molecular events (e.g., ligand exchange around a metal center) has emerged from these fundamental studies. A second advance has focused on investigations of the ordering of LCs at interfaces with immiscible isotropic fluids, particularly water. In contrast to prior studies of surface-induced ordering of LCs on solid surfaces, LC-aqueous interfaces are deformable and molecules at these interfaces exhibit high levels of mobility and thus can reorganize in response to changes in the interfacial environment. A range of fundamental investigations involving these LC-aqueous interfaces have revealed that (i) the spatial and temporal characteristics of assemblies formed from biomolecular interactions can be reported by surface-driven ordering transitions in the LCs, (ii) the interfacial phase behavior of molecules and colloids can be coupled to (and manipulated via) the ordering (and nematic elasticity) of LCs, and (iii) the confinement of LCs leads to unanticipated size-dependent ordering (particularly in the context of LC emulsion droplets). The third and final advance addressed in this article involves interactions between colloids mediated by LCs. Recent experiments involving microparticles deposited at the LC-aqueous interface have revealed that LC-mediated interactions can drive interfacial assemblies of particles through reversible ordering transitions (e.g., from 1D chains to 2D arrays with local hexagonal symmetry). In addition, recent single-nanoparticle measurements suggest that the ordering of LCs about nanoparticles differs substantially from micrometer-sized particles and that the interactions between nanoparticles mediated by the LCs are far weaker than predicted by theory (sufficiently weak that the interactions are reversible and thus enable self-assembly). Finally, LC-mediated interactions between colloidal particles have also been shown to lead to the formation of colloid-in-LC gels that possess mechanical properties relevant to the design of materials that interface with living biological systems. Overall, these three topics serve to highlight the broad opportunities that exist to do fundamental interfacial science and discovery-oriented research involving LCs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-cadence and high-resolution Hα imaging spectroscopy of a circular flare's remote ribbon with IBIS

We present an unprecedented high-resolution Hα imaging spectroscopic observation of a C4.1 flare taken with the Interferometric Bidimensional Spectrometer (IBIS) in conjunction with the adaptive optics system at the 76 cm Dunn Solar Telescope on 2011 October 22 in the active region NOAA 11324. Such a two-dimensional spectroscopic observation covering the entire evolution of a flare ribbon with high spatial (0.''1 pixel{sup –1} image scale), cadence (4.8 s), and spectral (0.1 Å step size) resolution is rarely reported. The flare consists of a main circular ribbon that occurred in a parasitic magnetic configuration and a remote ribbon that was observed by the IBIS. Such a circular-ribbon flare with a remote brightening is predicted in three-dimensional fan-spine reconnection but so far has been rarely studied. During the flare impulsive phase, we define 'core' and 'halo' structures in the observed ribbon based on IBIS narrowband images in the Hα line wing and line center. Examining the Hα emission spectra averaged in the flare core and halo areas, we find that only those from the flare cores show typical nonthermal electron beam heating characteristics that have been revealed by previous theoretical simulations and observations of flaring Hα line profiles. These characteristics include broad and centrally reversed emission spectra, excess emission in the red wing with regard to the blue wing (i.e., red asymmetry), and redshifted bisectors of the emission spectra. We also observe rather quick timescales for the heating (∼30 s) and cooling (∼14-33 s) in the flare core locations. Therefore, we suggest that the flare cores revealed by IBIS track the sites of electron beam precipitation with exceptional spatial and temporal resolution. The flare cores show two-stage motion (a parallel motion along the ribbon followed by an expansion motion perpendicular to the ribbon) during the two impulsive phases of the flare. Some cores jump quickly (30 km s{sup –1}) between discrete magnetic elements implying reconnection involving different flux tubes. We observe a very high temporal correlation (≳ 0.9) between the integrated Hα and hard X-rays (HXR) emission during the flare impulsive phase. A short time delay (4.6 s) is also found in the Hα emission spikes relative to HXR bursts. The ionization timescale of the cool chromosphere and the extra time taken for the electrons to travel to the remote ribbon site may contribute to this delay.

79 ASTRONOMY AND ASTROPHYSICS↗

A Dual-Gated Structures for Lossless Ion Manipulations-Ion Mobility Orbitrap Mass Spectrometry Platform for Combined Ultra-High-Resolution Molecular Analysis

High-resolution ion mobility spectrometry-mass spectrometry (HR-IMS-MS) instruments have enormously advanced the ability to characterize complex biological mixtures. Unfortunately, HR-IMS and HR-MS measurements are typically performed independently due to mismatches in analysis time scales. Here we overcome this limitation by using a dual-gated ion injection approach to couple an 11-meter path length structures for lossless ion manipulations (SLIM) module to a Q-Exactive Plus Orbitrap MS. The dual-gate setup was implemented by placing one ion gate before the SLIM module and a second ion gate after. The dual-gated ion injection approach allowed the new SLIM-Orbitrap platform to simultaneously perform an 11-meter SLIM separation, Orbitrap mass analysis using the highest selectable mass resolution setting (up to 140k), and high-energy collision induced dissociation (HCD) in ~25 minutes over an $m/z$ range of ~1500 amu. The SLIM-Orbitrap was initially characterized using a mixture of standard phosphazene cations and demonstrated an average SLIM CCS resolving power (Rp CCS ) of ~218 and SLIM peak capacity of ~156 while simultaneously obtaining high mass resolutions. SLIM-Orbitrap analysis with fragmentation was then performed on mixtures of standard peptides and two reverse peptides (SDGRG 1+ , GRGDS 1+ , Rp CCS = 305) to demonstrate the utility of combined HR-IMS-MS/MS measurements for peptide identification. Our new HR-IMS-MS/MS capability was further demonstrated by analyzing a complex lipid mixture and showcasing SLIM separations on isobaric lipids. In conclusion, this new SLIM-Orbitrap platform demonstrates a critical new capability for proteomics and lipidomics applications, and the high-resolution multimodal data obtainable with this system establishes the foundation for reference-free identification of unknown ion structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Final Report UCLA-Thermochemical Storage with Anhydrous Ammonia

In ammonia-based thermochemical energy storage (TCES), ammonia is dissociated endothermically as it absorbs solar energy during the daytime. When energy is required, the reverse reaction releases energy to heat a working fluid such as steam, to produce electricity. Ammonia-based TCES has great advantages of simplicity, low cost reactants, and a strong industrial base in the conventional ammonia industry. The concept has been demonstrated over three decades of research at Australian National University, achieving a 24-hour demonstration of a complete system. At the start of this project, three challenges were identified that would have to be addressed to show that the system is technically and economically viable for incorporation into a CSP plant with an advanced, high temperature power block. All three of these challenges have now been addressed: 1. The ammonia synthesis reaction had not, to our knowledge, been carried out at temperatures consistent with modern power blocks (i.e., ~650°C). The technical feasibility of operating a reactor under high-temperature, near-equilibrium conditions was an unknown, and was therefore a technical risk. The project has successfully demonstrated steam heating to 650°C and energy recovery to steam at the 5 kWt level. 2. The ammonia system has a relatively low enthalpy of reaction combined with gas phase reactants. This is not a direct disadvantage since the reactants themselves are low cost. The challenge lies in storing the required volume of reactants cost effectively. Therefore, a second key goal was to show, through techno-economic analysis, that underground storage technologies can be used to store the energy-rich gas at a cost that is consistent with the SunShot cost goal. We have identified two promising technologies for gas storage: storage in salt caverns has an estimated cost of 1(USD)/kWht and storage in drilled shafts could be on the order of 7(USD)/kWht. Together these two options answer the technical challenge associated with storage of gas phase components. 3. While this project is primarily concerned with high-temperature heat recovery and methods to store the gaseous components, it is also important to consider the feasibility of the entire system. Consequently, an additional goal was to perform analysis to show the feasibility of integrating endothermic reactors within a tower receiver. A conceptual design of an ammonia dissociation receiver/reactor has been developed that fits into the same size cylindrical envelope as the molten salt receiver in SAM, and has the same design thermal capacity. The calculated thermal efficiency of this receiver is 94.6%. Thus, this investigation has established the technical feasibility of a surround field tower system using ammonia dissociation. With these challenges addressed, we proceeded to design a full-scale synthesis and heat recovery system. A model was developed and validated by comparison with our experimental data. A parametric study showed, among other things, the importance of using small tube diameters and spacing to enhance heat transfer. Multi-parameter optimization was used to find a design that minimizes the wall material volume. Finally, cost estimation shows that the ammonia system has good prospects of meeting the Sunshot 15(USD)/kWht target: estimated costs of the entire synthesis system for the 220 MWt plant with 6 hours of storage are 13(USD)/kWht using salt cavern storage and 18(USD)/kWht using shaft drilling. Costs per kWht are even lower with more hours of storage. With the established technology of ammonia synthesis as a starting point, the successes of the project have mitigated technical risks associated with high-temperature synthesis reaction, underground storage, and tower receiver design. Estimated costs are less than 15(USD)/kWht with salt cavern storage. It is now possible to map a time line to commercial deployment that is likely to be shorter and less risky than other thermochemical cycles under active investigation. UCLA has filed a patent that protects the new ideas developed during this project. Discussions are ongoing with potential investors with the aim of partnering for further work. As well as immediate improvements and extra work with the existing experimental system, a key goal is to extend it to a small solar-driven project at an early opportunity.

14 SOLAR ENERGY↗

Topological field theory of dynamical systems

Here, it is shown that the path-integral representation of any stochastic or deterministic continuous-time dynamical model is a cohomological or Witten-type topological field theory, i.e., a model with global topological supersymmetry (Q-symmetry). As many other supersymmetries, Q-symmetry must be perturbatively stable due to what is generically known as non-renormalization theorems. As a result, all (equilibrium) dynamical models are divided into three major categories: Markovian models with unbroken Q-symmetry, chaotic models with Q-symmetry spontaneously broken on the mean-field level by, e.g., fractal invariant sets (e.g., strange attractors), and intermittent or self-organized critical (SOC) models with Q-symmetry dynamically broken by the condensation of instanton-antiinstanton configurations (earthquakes, avalanches, etc.) SOC is a full-dimensional phase separating chaos and Markovian dynamics. In the deterministic limit, however, antiinstantons disappear and SOC collapses into the 'edge of chaos.' Goldstone theorem stands behind spatio-temporal self-similarity of Q-broken phases known under such names as algebraic statistics of avalanches, 1/f noise, sensitivity to initial conditions, etc. Other fundamental differences of Q-broken phases is that they can be effectively viewed as quantum dynamics and that they must also have time-reversal symmetry spontaneously broken. Q-symmetry breaking in non-equilibrium situations (quenches, Barkhausen effect, etc.) is also briefly discussed.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Obstacles to quantum annealing in a planar embedding of XORSAT

We introduce a planar embedding of the k-regular k-XORSAT problem, in which solutions are encoded in the ground state of a classical statistical mechanics model of reversible logic gates arranged on a square grid and acting on bits that represent the Boolean variables of the problem. The special feature of this embedding is that the resulting model lacks a finite-temperature phase transition, thus bypassing the first-order thermodynamic transition known to occur in the random graph representation of XORSAT. In spite of this attractive feature, the thermal relaxation into the ground state displays remarkably slow glassy behavior. The question addressed in this paper is whether this planar embedding can afford an efficient path to solution of k-regular k-XORSAT via quantum adiabatic annealing. We first show that our model bypasses an avoided level crossing and consequent exponentially small gap in the limit of small transverse fields. We then present quantum Monte Carlo results for our embedding of the k-regular k-XORSAT that strongly support a picture in which second-order and first-order transitions develop at a finite transverse field for k = 2 and k = 3, respectively. Furthermore, this translates into power-law and exponential dependences in the scaling of energy gaps with system size, corresponding to times-to-solution which are, respectively, polynomial and exponential in the number of variables. We conclude that neither classical nor quantum annealing can efficiently solve our reformulation of XORSAT, even though the original problem can be solved in polynomial time by Gaussian elimination.

2-dimensional systems↗

Protein Adhesion on Semi-Fluorinated Polystyrene Surfaces in Static and Dynamic Measurements

Reducing protein adhesion is a critical strategy in fouling-resistant material innovation, with broad applications spanning biomedical and healthcare devices, biosensors, industrial and environmental systems, and other important technological domains. Here, in this study, we elucidated protein adhesion behavior on polystyrene-based thin films by neutron reflectometry (NR) and quartz crystal microbalance with dissipation (QCM-D), using both lysozyme and bovine serum albumin (BSA) as model proteins. To this end, semifluorinated polystyrene thin films with gradient wettability and surface energy were fabricated through dry processing using plasma oxidation and gas-phase deposition. Although it is believed that a fully fluorinated alkyl chain offers extremely low surface energy, thus rejecting foulants, and has been used in many fouling-resistant surface designs, enhanced protein–surface interactions were observed consistently in NR and QCM-D results, due to the combined effects of surface morphology and chemistry. On the contrary, depositing shorter fluorinated silane onto a hydrophilic PS surface contributed to a more homogeneous nanoscale fluorine coating, resulting in less initial protein adsorption and improved surface recovery. Comparative analysis of proteins with different sizes on the nanopatterned semifluorinated surface revealed the influence of molecular characteristics on surface interactions. Lysozyme, being smaller and more compact, showed faster adsorption kinetics and higher surface coverage but largely reversible binding, whereas BSA, with its larger and more flexible structure, formed broader and more stable interfacial layers. This study fills the gap in understanding protein adhesion within the range of hydrophobicity (water contact angle ∼90°), as current strategies often associate with extreme hydrophilic and superhydrophobic surfaces due to hydration or low-surface-energy rejection mechanisms, respectively. It also provides in-depth insights into current combinatorial fouling-resistant surface design.

Yuan, Yue [Oak Ridge National Laboratory (ORNL), O↗

La 2 ⁢O 3 ⁢Mn 2 ⁢Se 2 : A correlated insulating layered d-wave altermagnet

Altermagnets represent a new class of magnetic phases without net magnetization, invariant under a combination of rotation and time reversal. Unlike conventional collinear antiferromagnets (AFM), altermagnets could lead to new correlated states and important material properties deriving from their nonrelativistic spin-split band structure. Indeed, they serve as the magnetic analogue of unconventional superconductors and can yield spin-polarized electrical currents in the absence of external magnetic fields, making them promising candidates for next-generation spintronics. Here, we report altermagnetism in the correlated insulator, magnetically ordered tetragonal oxychalcogenide, L⁢a 2 ⁢O 3⁢ M⁢n 2 ⁢S⁢e 2 . Symmetry analysis reveals a 𝑑 𝑥 2 −𝑦 2 -wave-like spin-momentum locking arising from the M⁢n 2 ⁢O Lieb lattice, supported by density functional theory (DFT) calculations. Magnetic measurements confirm the AFM transition below ∼166K while neutron pair distribution function analysis reveals a 2D short-range magnetic order that persists above the Néel temperature. Single crystals are grown and characterized using x-ray diffraction, optical and electron microscopy, and micro-Raman spectroscopy to confirm the crystal structure, stoichiometry, and uniformity. Furthermore, our findings establish L⁢a 2⁢ O 3 ⁢M⁢n 2⁢ S⁢e 2 as a model altermagnetic system realized on a Lieb lattice.

36 MATERIALS SCIENCE↗

Time-reversal invariant topological moiré flat band: A platform for the fractional quantum spin Hall effect

Motivated by recent observation of the quantum spin Hall effect in monolayer germanene and twisted bilayer transition-metal-dichalcogenides (TMDs), we study the topological phases of moir twisted bilayers with time-reversal symmetry and spin sz conservation. By using a continuum model description which can be applied to both germanene and TMD bilayers, we show that at small twist angles the emergent moir flat bands can be topologically nontrivial due to inversion symmetry breaking. Each of these flat bands admits a lowest-Landau-level description for each spin projection in the chiral limit and at magic twist angle. Furthermore, this allows for the construction of a many-body Laughlin state with time-reversal symmetry which can be stabilized by a short-range pseudopotential, and therefore serves as an ideal platform for realizing the so-far elusive fractional quantum spin Hall effect with emergent spin-1/2 U(1) symmetry.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Topological Signature of Stratospheric Poincaré-Gravity Waves

The rotation of Earth breaks time-reversal and reflection symmetries in an opposite sense north and south of the equator, leading to a topological origin for certain atmospheric and oceanic equatorial waves. Away from the equator, the rotating shallow-water and stably stratified primitive equations exhibit Poincaré inertia–gravity waves that have nontrivial topology as evidenced by their strict superinertial time scale and a phase singularity in frequency–wavevector space. This nontrivial topology then predicts, via the principle of bulk-interface correspondence, the existence of two equatorial waves along the equatorial interface, the Kelvin and Yanai waves. To directly test the nontrivial topology of Poincaré-gravity waves in observations, we examine ERA5 data and study cross correlations between the wind velocity and geopotential height of the midlatitude stratosphere at the 50 hPa height. We find the predicted vortex and antivortex in the relative phase of the geopotential height and velocity at the high frequencies of the waves. By contrast, lower-frequency planetary waves are found to have trivial topology also as expected from theory. These results demonstrate a new way to understand stratospheric waves and provide a new qualitative tool to investigate waves in other components of the climate system.

54 ENVIRONMENTAL SCIENCES↗

Pressure-induced development of bonding in NiAs type compounds and polymorphism of NiP

A reversible, displacive, pressure-induced structural phase transition has been found to occur in nickel monophosphide NiP at approximately 3.5 GPa by means of in situ synchrotron single-crystal X-ray diffraction. The new phase, with Pearson symbol oC56, assumes an orthorhombic structure with Cmc2{sub 1} space group and unit cell parameters a=23.801(2) {angstrom}, b=5.9238(6) {angstrom}, and c=4.8479(4) {angstrom} at 5.79 GPa. The high-pressure phase is a superstructure of the ambient, oP16 phase with multiplicity of 3.5. The phosphorous sublattice gradually converts from the net of isolated P{sub 2} dimers found in the ambient NiP, towards zig-zag polymeric P{infinity} chains found in MnP-type structures. The transformation involves development of triatomic phosphorous clusters and interconnected Ni slabs with diamondoid topology. The high-pressure phase, which represents intermediate polymerization step, is a commensurately modulated superstructure of the NiAs aristotype. The phase transformation in NiP bears resemblance to the effect of successive substitution of Si or Ge in place of P found in the series of stoichiometric inhomogeneous linear structures in ternary NiP{sub 1-x}Si{sub x} and NiP{sub 1-x}Ge{sub x} systems.

Dera, Przemyslaw↗

Microphase separation in copolymers of hydrophilic PEG blocks and hydrophobic tyrosine-derived segments using simultaneous SAXS/WAXS/DSC

Hydration- and temperature-induced microphase separations were investigated by simultaneous small- and wide-angle X-ray scattering (SAXS and WAXS) and differential scanning calorimetry (DSC) in a family of copolymers in which hydrophilic poly(ethylene glycol) (PEG) blocks are inserted randomly into a hydrophobic polymer made of either desaminotyrosyl-tyrosine ethyl ester (DTE) or iodinated I{sub 2}DTE segments. Iodination of the tyrosine rings in I{sub 2}DTE increased the X-ray contrast between the hydrophobic and hydrophilic segments in addition to facilitating the study of the effect of iodination on microphase separation. The formation of phase-separated, hydrated PEG domains is of considerable significance as it profoundly affects the polymer properties. The copolymers of DTE (or I{sub 2}DTE) and PEG are a useful model system, and the findings presented here may be applicable to other PEG-containing random copolymers. In copolymers of PEG and DTE and I{sub 2}DTE, the presence of PEG depressed the glass transition temperature (T{sub g}) of the copolymer relative to the homopolymer, poly(DTE carbonate), and the DTE/I{sub 2}DTE segments hindered the crystallization of the PEG segments. In the dry state, at large PEG fractions (>70 vol%), the PEG domains self-assembled into an ordered structure with 14-18 nm distance between the domains. These domains gave rise to a SAXS peak at all temperatures in the iodinated polymers, but only above the T{sub g} in non-iodinated polymers, due to the unexpected contrast-match between the crystalline PEG domains and the glassy DTE segments. Irrespective of whether PEG was crystalline or not, immersion of these copolymers in water resulted in the formation of hydrated PEG domains that were 10-20 nm apart. Since both water and the polymer chains must be mobile for the phase separation to occur, the PEG domains disappeared when the water froze, and reappeared as the ice began to melt. This transformation was reversible, and showed hysteresis as did the melting of ice and freezing of the water incorporated into the polymer. PEG-water complexes and PEG-water eutectics were observed in WAXS and DSC scans, respectively.

36 MATERIALS SCIENCE↗

Scalable Polymer Precursor Based LiPON Type Li-Metal Interface Enabled High Performance Li-Sulfur Battery

The Battery 500 program objective is to research, develop, and demonstrate lithium battery technologies capable of achieving 500 Wh/kg with stable lifetime of 1000 cycles. This Battery 500 seedlings project has demonstrated a new approach and a pathway toward the program’s goals in just one awarded and executed phase. Cells have been assembled, tested, and evaluated. This report details efforts to develop polymer precursor electrolytes that offer properties anticipated to be similar or superior to LiPON glasses. Such precursors offer the potential to be used to process LiPON-like thin glass/ceramic coatings for use in lithium batteries. LiPON glasses provide a design basis for the synthesis of sets of oligomers/polymers by lithiation of OP(NH 2 ) 3-x (NH) x [from OP(NH) 3 ], OP(NH 2 ) 3-x (NHSiMe 3 ) x and [P=N] 3 (NHSiMe 3 ) 6-x (NH) x . Polymer electrolytes impregnated in/on celgard exhibit Li+ conductivities up to ~1×10 -5 S/cm at room temperature and are thermally stable to ≈150 °C. A Li-S battery assembled using a Li 6 SiPON composition polymer electrolyte exhibits an initial reversible capacity of 1500 mAh/g sulfur and excellent cycle performance at 0.25 and 0.5 C rate over 120 cycles, declining to 750 mAh/g at after a 220 h test period. At the same time, computational studies were performed to understand the conduction mechanism of LIPON and its interaction with Li metal. These initial project results provide a foundation for further development of the system to achieve the program goal.

25 ENERGY STORAGE↗