Search NASA⌕ Search

SEARCH · Search NASA

Results for “stream flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Annular arc accelerator shock tube

An annular arc accelerator shock tube employs a cold gas driver to flow a stream of gas from an expansion section through a high voltage electrode section to a test section, thus driving a shock wave in front of it. A glow discharge detects the shock wave and actuates a trigger generator which in turn fires spark-gap switches to discharge a bank of capacitors across a centered cathode and an annular anode in tandem electrode sections. The initial shock wave passes through the anode section from the cathode section thereby depositing energy into the flow gas without the necessity of any diaphragm opening in the gas flow from the expansion section through the electrode sections.

Leibowitz, L. P.↗

Plasma formation in a double-gap vircator

Time-resolved light emission imaging was used to observe the plasma formation within the cavity of the double-gap vircator powered by a sub-microsecond generator ({approx}500 kV, {approx}10 kA, {approx}500 ns). The vircator generated well reproducible S-band microwave pulses of {approx}200 MW peak power and up to 200 ns full duration. The plasma light emission was observed {approx}30 ns prior to the ending of the generated microwave pulses at the surface of the aluminum foil separating the vircator cavity gaps, in the gap where the virtual cathode is formed. Estimations showed that the energy deposition into the foil by the high-current electron beam is sufficient for the surface plasma formation. The plasma ions accelerated toward the virtual cathode neutralize its electron space charge. The latter was confirmed by the increase in the electron current transmitted through the vircator cavity. In addition, the time of the plasma appearance was determined by comparing the measured transmitted current with that following from the one-dimensional model of a stationary un-neutralized two-stream electron flow. This time agrees with the maximum of the microwave power observed in the experiments, thus showing that the plasma ions cause the termination of the microwave generation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A Dynamically Reconfigurable System for Closed-Loop Measurements of Network Traffic

Streaming network traffic measurement and analysis is critical for detecting and preventing any real-time anomalies in the network. The high speeds and complexity of today's networks, coupled with ever evolving threats, necessitate closing of the loop between measurements and their analysis in real time. The ensuing system demands high levels of programmability and processing where streaming measurements adapt to the changing network behavior in a goal-oriented manner. In this work, we exploit the features and requirements of the problem and develop an application-specific FPGA-based closed-loop measurement (CLM) system. We make novel use of fine-grained partial dynamic reconfiguration (PDR) as underlying reprogramming paradigm, performing low-latency just-in-time compiled logic changes in FPGA fabric corresponding to the dynamic measurement requirements. Our innovative dynamically reconfigurable socket offers 3× logic savings over conventional static solutions, while offering much reduced reconfiguration latencies over conventional PDR mechanisms. Here, we integrate multiple sockets in a highly parallel CLM framework and demonstrate its effectiveness in identifying heavy flows in streaming network traffic. The results using an FPGA prototype offer 100 percent detection accuracy while sustaining increasing link speeds.

97 MATHEMATICS AND COMPUTING↗

Emissions from ethanol-blended fossil fuel flames

A fundamental study to investigate the emission characteristics of ethanol-blended fossil fuels is presented. Employing a heterogeneous experimental setup, emissions are measured from diffusion flames around spherical porous particles. Using an infusion pump, ethanol-fossil fuel blend is transpired into a porous sphere kept in an upward flowing air stream. A typical probe of portable digital exhaust gas analyzer is placed in and around the flame with the help of a multi-direction traversing mechanism to measure emissions such as un-burnt hydrocarbons, carbon monoxide and carbon dioxide. Since ethanol readily mixes with water, emission characteristics of ethanol-water blends are also studied. For comparison purpose, emissions from pure ethanol diffusion flames are also presented. A simplified theoretical analysis has been carried out to determine equilibrium surface temperature, composition of the fuel components in vapor-phase and heat of reaction of each blend. These theoretical predictions are used in explaining the emission characteristics of flames from ethanol blends. (author) This paper presents the results of an experimental study of flow structure in horizontal equilateral triangular ducts having double rows of half delta-wing type vortex generators mounted on the duct's slant surfaces. The test ducts have the same axial length and hydraulic diameter of 4 m and 58.3 mm, respectively. Each duct consists of double rows of half delta wing pairs arranged either in common flow-up or common flow-down configurations. Flow field measurements were performed using a Particle Image Velocimetry Technique for hydraulic diameter based Reynolds numbers in the range of 1000-8000. The secondary flow field differences generated by two different vortex generator configurations were examined in detail. The secondary flow is found stronger behind the second vortex generator pair than behind the first pair but becomes weaker far from the second pair in the case of Duct1. However, the strength of the secondary flow is found nearly the same behind the first and the second vortex generator pair as well as far from the second vortex generator pair in the case of Duct2. Both ducts are able to create a counter-rotating and a second set of twin foci. Duct2 is able to create the second set of twin foci in an earlier streamwise location than Duct1, as these foci are well-known to their heat transfer augmentation. A larger vortex formation area and a greater induced vorticity field between vortex pairs are observed for Duct2 compared with Duct1. As the induced flow field between the vortex pairs increases the heat transfer, and as the flow field between the vortex cores is found larger in the case of Duct2, therefore, it is expected to obtain better heat transfer characteristics for Duct2 compared with Duct1. (author)

09 BIOMASS FUELS↗

Detailed Studies on the Structure and Dynamics of Reacting Dusty Flows at Normal and Microgravity

Dusty reacting flows are of particular interest for a wide range of applications. Inert particles can alter the flammability and extinction limits of a combustible mixture. Reacting particles can release substantial amount of heat and can be used either for power generation or propulsion. Accumulation of combustible particles in air can result in explosions which, for example, can occur in grain elevators, during lumber milling and in mine galleries. Furthermore, inert particles are used as flow velocity markers in reacting flows, and their velocity is measured by non-intrusive laser diagnostic techniques. Despite their importance, dusty reacting flows have been less studied and understood compared to gas phase as well as sprays. The addition of solid particles in a flowing gas stream can lead to strong couplings between the two phases, which can be of dynamic, thermal, and chemical nature. The dynamic coupling between the two phases is caused by the inertia that causes the phases to move with different velocities. Furthermore, gravitational, thermophoretic, photophoretic, electrophoretic, diffusiophoretic, centrifugal, and magnetic forces can be exerted on the particles. In general, magnetic, electrophoretic, centrifugal, photophoretic, and diffusiophoretic can be neglected. On the other hand, thermophoretic forces, caused by steep temperature gradients, can be important. The gravitational forces are almost always present and can affect the dynamic response of large particles. Understanding and quantifying the chemical coupling between two phases is a challenging task. However, all reacting particles begin this process as inert particles, and they must be heated before they participate in the combustion process. Thus, one must first understand the interactions of inert particles in a combustion environment. The in-detail understanding of the dynamics and structure of dusty flows can be only advanced by considering simple flow geometries such as the opposed-jet, stagnation-type. In such configurations the imposed strain rate is well characterized, and the in-depth understanding of the details of the physico-chemical processes can be systematically obtained. A number of computational and experimental studies on spray and particle flows have been conducted in stagnation-type configurations. Numerically, the need for a hybrid Eulerian-Lagrangian approach has been identified by Continillo and Sirignano, and the use of such approach has allowed for the prediction of the phenomenon of droplet flow reversal. Gomez and Rosner have conducted a detailed study on the particle response in the opposed-jet configuration, and the particle thermophoretic diffusivities were determined experimentally. Sung, Law and co-workers have conducted numerical studies on the effect of strain rate and temperature gradients on the dynamics of inert particles, as a way of understanding potential errors in experimental LDV data that may arise from thermophoretic forces. This investigation is a combined experimental and numerical study on the details of reacting dusty flows. The specific tasks are: (1) Experimental determination of laminar flame speeds, and extinction strain rates of dusty flows at normal- and micro-gravity as functions of the particle type, particle initial diameter, particle initial number density, and gas phase chemical composition; (2) Detailed numerical simulation of the experiments. Results are compared with experiments and the adequacy of theoretical models is assessed; and (3) Provision of enhanced insight into the thermo-chemical coupling between the two phases.

Andac, M. Gurhan↗

Numerical Simulation of an Enclosed Laminar Jet Diffusion Flame in Microgravity Environment: Comparison with ELF Data

Enclosed diffusion flames are commonly found in practical combustion systems, such as the power-plant combustor, gas turbine combustor, and jet engine after-burner. In these systems, fuel is injected into a duct with a co-flowing or cross-flowing air stream. The diffusion flame is found at the surface where the fuel jet and oxygen meet, react, and consume each other. In combustors, this flame is anchored at the burner (i.e., fuel jet inlet) unless adverse conditions cause the flame to lift off or blow out. Investigations of burner stability study the lift off, reattachment, and blow out of the flame. Flame stability is strongly dependent on the fuel jet velocity. When the fuel jet velocity is sufficiently low, the diffusion flame anchors at the burner rim. When the fuel jet velocity is increased, the flame base gradually moves downstream. However, when the fuel jet velocity increases beyond a critical value, the flame base abruptly jumps downstream. When this "jump" occurs, the flame is said to have reached its lift-off condition and the critical fuel jet velocity is called the lift-off velocity. While lifted, the flame is not attached to the burner and it appears to float in mid-air. Flow conditions are such that the flame cannot be maintained at the burner rim despite the presence of both fuel and oxygen. When the fuel jet velocity is further increased, the flame will eventually extinguish at its blowout condition. In contrast, if the fuel jet velocity of a lifted flame is reduced, the flame base moves upstream and abruptly returns to anchor at the burner rim. The fuel jet velocity at reattachment can be much lower than that at lift off, illustrating the hysteresis effect present in flame stability. Although there have been numerous studies of flame stability, the controlling mechanisms are not well understood. This uncertainty is described by Pitts in his review of various competing theories of lift off and blow out in turbulent jet diffusion flames. There has been some research on the stability of laminar flames, but most studies have focused on turbulent flames. It is also well known that the airflow around the fuel jet can significantly alter the lift off, reattachment and blow out of the jet diffusion flame. Buoyant convection is sufficiently strong in 1-g flames that it can dominate the flow-field, even at the burner rim. In normal-gravity testing, it is very difficult to delineate the effects of the forced airflow from those of the buoyancy-induced flow. Comparison of normal-gravity and microgravity flames provides clear indication of the influence of forced and buoyant flows on the flame stability. The overall goal of the Enclosed Laminar Flames (ELF) investigation (STS-87/USMP-4 Space Shuttle mission, November to December 1997) is to improve our understanding of the effects of buoyant convection on the structure and stability of co-flow diffusion flame, e.g., see http://zeta.lerc.nasa.gov/expr/elf.htm. The ELF hardware meets the experiment hardware limit of the 35-liter interior volume of the glovebox working area, and the 180x220-mm dimensions of the main door. The ELF experiment module is a miniature, fan-driven wind tunnel, equipped with a gas supply system. A 1.5-mm diameter nozzle is located on the duct's flow axis. The cross section of the duct is nominally a 76-mm square with rounded corners. The forced air velocity can be varied from about 0.2 to 0.9 m/s. The fuel flow can be set as high as 3 std. cubic centimeter (cc) per second, which corresponds to a nozzle exit velocity of up to 1.70 m/s. The ELF hardware and experimental procedure are discussed in detail in Brooker et al. The 1-g test results are repeated in several experiments following the STS-87 Mission. The ELF study is also relevant to practical systems because the momentum-dominated behavior of turbulent flames can be achieved in laminar flames in microgravity. The specific objectives of this paper are to evaluate the use reduced model for simulation of flame lift-off and blowout.

Jia, Kezhong↗

Generation of Subauroral Longitudinally Extended Emissions Following Intensifications of the Poleward Boundary of the Substorm Bulge and Streamer Production

Observations showing the development of Subauroral Longitudinally Extended Emigerssions on a global scale are presented. It is demonstrated that they occur as a separation of an east-west arc-like band of luminosity that detaches away from the equatorward edge of the auroral distribution following episodes of auroral streamer production. They persist for time intervals on the order of ~30 min and devolve into patchy disjointed segments before they fade. Emissions are seen in both 557.7 nm OI and 391.4 nm N + 2 1NG lines, and 630.0 nm emissions are often observed equatorward. The 391.4 nm emissions are typically weaker and fade away more quickly than the 557.7 nm emissions, suggesting that an auroral precipitation source is initially present but is rapidly depleted as the forms age. All cases are associated with enhanced Subauroral Polarization Stream (SAPS) flows, and one event shows clear association with large-scale Giant Undulations (GUs) and the formation of spur-like forms that fold equatorward under the main oval. A model is proposed for the production of subauroral longitudinally extended forms in which nonlinear growth of SAPS-induced surface waves on the plasmapause results in a disruption of the boundary. It is suggested that hot plasma of plasma sheet origin becomes entrained in the plasmasphere to produce transient precipitation-associated auroral emissions that may decay into STEVE emissions and that cold dense plasma from the plasmasphere becomes entrained onto open drift paths to feed long-lived drainage plumes. This process may occur quasi periodically during intense substorms and storm-time conditions.

79 ASTRONOMY AND ASTROPHYSICS↗

Calculation of two-dimensional inlet flow fields in a supersonic free stream by an implicit marching code with nonorthogonal mesh generation: User's manual

An implicit, shock-capturing finite-difference code which is used to calculate two-dimensional inlet flow fields in a supersonic free stream is explained. The Euler equations are subjected to general nonorthogonal transformation and a body-fitted coordinate system is employed. The mathematical formulation of the problem is given along with the numerical algorithm. Initial and boundary conditions, numerical stability, program limitations, and accuracy is discussed. An overall program logic as well as instructions for program use and operation are also furnished.

Biringen, S. H.↗

THE WHITE DWARF IN EM CYGNI: BEYOND THE VEIL

We present a spectral analysis of the Far Ultraviolet Spectroscopic Explorer (FUSE) spectra of the eclipsing double-line spectroscopic binary EM Cygni (EM Cyg), a Z Cam DN system. The FUSE spectrum, obtained in quiescence, consists of four individual exposures (orbits): two exposures, at orbital phases {phi} {approx} 0.65 and {phi} {approx} 0.90, have a lower flux; and two exposures, at orbital phases {phi} = 0.15 and 0.45, have a relatively higher flux. The change of flux level as a function of the orbital phase is consistent with the stream material (flowing over and below the disk from the hot spot region to smaller radii) partially masking the white dwarf. We carry out a spectral analysis of the FUSE data, obtained at phase 0.45 (when the flux is maximal), using synthetic spectra generated with the codes TLUSTY and SYNSPEC. Using a single white dwarf spectral component, we obtain a white dwarf temperature of 40, 000 K {+-} 1000 K, rotating at 100 km s{sup -1}. The white dwarf, or conceivably, the material overflowing the disk rim, shows suprasolar abundances of silicon, sulphur, and possibly nitrogen. Using a white dwarf+disk composite model, we obtain that the white dwarf temperature could be even as high as 50,000 K, contributing more than 90% of the FUV flux, and the disk contributing less than 10% must have a mass accretion rate reaching 10{sup -10} M{sub sun} yr{sup -1}. The single white dwarf model fits the absorption lines better than the white dwarf+disk model, but the white dwarf+disk model fits better the continuum in the shorter wavelengths. In both cases, however, we obtain that the white dwarf temperature is much higher than previously estimated. We emphasize the importance of modeling the spectra of EM Cyg around phase {phi} < 0.5, when the white dwarf and disk are facing the observer, and we suggest that the discrepancy between the present analysis and previous spectral analysis might be due to the occulting effect of the stream veiling the white dwarf and disk.

79 ASTRONOMY AND ASTROPHYSICS↗

Five kHz thermometry in turbulent spray flames using chirped-probe-pulse femtosecond CARS, part II: Structure of reaction zones

Temperature was measured in turbulent spray flames of ethanol and acetone stabilized on the piloted Sydney Needle Spray Burner (SYNSBURN TM ) using single-laser-shot, chirped-probe-pulse femtosecond coherent anti-Stokes Raman spectroscopy (CPP-fs-CARS) with a repetition rate of 5 kHz. The burner features air-blast atomization of liquid injected from a needle that can be translated by a length Lr within a co-flowing air stream so that piloted spray flames ranging from dilute to dense can be studied. Part I of these investigations has reported on the CPP-fs-CARS technique and extensive details of data processing methodology. Part II is concerned with the structure of the reaction zones at different spray loadings and for different departures from blow-off. While not performed simultaneously, measurements of the size distribution of liquid fragments are also reported and discussed in conjunction with the measured temperature. Measured probability density functions of temperature show that for flames with the same liquid loading but different recess lengths, Lr, the near-field spray structure that forms upstream of x/D = 10 affects flame structure and stability further downstream. As the spray exiting the burner becomes denser, with a higher proportion of ligaments and ‘irregular’ shaped objects, the entrainment of hot pilot gases into the spray envelope is affected, hence changing the rates of vaporization and subsequent combustion. The reported results will also form a useful platform for validating sub-models of atomization and combustion in turbulent, dilute to dense spray flames.

42 ENGINEERING↗

A finite difference informed random walker (FDiRW) solver for strongly inhomogeneous diffusion problems

In nature, many complex multi-physics coupling problems exhibit strong diffusivity inhomogeneity. For instance, in the context of radionuclide absorption by porous wasteform materials within a flowing waste stream, the difference of species’ diffusivity in solid and liquid phases spans by 3~8 orders of magnitude. To solve the diffusion equations with strongly inhomogeneous diffusivity, traditional discretization-based methods, such as the Finite Difference Method (FDM), require infinitesimally small time steps (<10 -10 ) as high spatial resolutions are employed in most microstructure evolution processes, leading to prohibitively high computational costs. Here, this work developed an integrated numerical approach (FDiRW: Finite Difference informed Random Walk) to tackle this challenge. The idea is that utilizing the Random Walk concept, the fast diffusion is modeled as a superposition of point source’s solution for a concentration distribution while FDM is used to obtain the point source’s solution at each node. A mesh-coarsening algorithm is developed to generate an exclusive coarse mesh for FDiRW approach to maximize its efficiency. The effectiveness of the coarse mesh-based FDiRW approach is validated by benchmarking Finite Difference solutions. Numerical results demonstrated that FDiRW achieves a remarkable 1000x computational efficiency improvement over FDM while preserving desired accuracy for a medium-sized model of 192 × 192 × 192 grids. Finally, as models scale up, a floating-point operations (PLOPs) analysis of the FDiRW algorithm reveals that its computational complexity grows quadratically in terms of the number of nodes employed in computation.

36 MATERIALS SCIENCE↗

Chirped-probe-pulse femtosecond CARS thermometry in turbulent spray flames

This paper presents temperature measurements in turbulent dilute and dense spray flames using single-laser-shot chirped-probe-pulse femtosecond coherent anti-Stokes Raman spectroscopy (CPP-fs-CARS). This ultrafast technique, with a repetition rate of 5 kHz, is applied to the piloted Sydney Needle Spray Burner (SYNSBURN TM ). The burner system features air-blast atomization of liquid injected from a needle that can be translated within a co-flowing air stream. The pilot-stabilized spray flames can range between the two extremes of dense and dilute by physically translating the needle tip relative to the burner's exit plane. The CPP-fs-CARS set-up has achieved integration times of 3 picoseconds (ps) as well as spatial resolution of approximately 800 µm along beam propagation and 60 µm in the transverse dimension. Brief details of the technique, calibration, correction of interferences, and spectral fitting processes are presented along with estimates of the associated error. The measurements are compared against well-established, line Raman–Rayleigh data for temperature collected in a turbulent CH 4 /air jet diffusion flame, which is largely non-sooting. At peak gaseous flame temperatures of up to 2512 K, the relative accuracy and precision were 2.8% and ±3.4%, respectively. Measurements in turbulent spray flames are shown after applying the relevant corrections based on non-resonant background (NRB) behavior and camera saturation effects on the shape of the CARS signal spectrum. Preliminary mapping of the temperature fields demonstrates the wealth of information available in this dataset which will provide insights into the spatio-temporal structure of spray flames once relevant statistical analysis is applied.

42 ENGINEERING↗

Dynamics of the chemo-optical response of supported films of nematic liquid crystals

We report a study that elucidates key physicochemical phenomena that underlie the dynamics of adsorbate-induced ordering transitions in micrometer-thick films of nematic liquid crystals (LCs) supported on chemically functionalized surfaces. By flowing a gas containing dimethyl methylphosphonate (DMMP) over a film of nematic 4-cyano-4'-pentylbiphenyl (5CB) supported on a surface decorated with aluminum perchlorate, we quantify the dynamics of the optical response (intensity of transmitted light) of the LC film as a function of key experimental parameters, including linear flow rate of the gas over the surface of the film and the concentration of the DMMP within the gas. Building from prior infrared spectroscopic analysis revealing that the optical response of the LC is due to an ordering transition triggered by competitive ligand-exchange reactions at the chemically functionalized surface (i.e., between the phosphonate and nitrile groups of the DMMP and LC, respectively, with the aluminum perchlorate-decorated surface), we interpret the measurements reported herein within the framework of a simple model of mass transport. The model reveals that the rate-limiting process underlying the response of the LC is the mass transport of the DMMP across the concentration boundary layer formed on the vapor side of the LC–vapor interface, and not the mass transport of DMMP across the LC film nor the intrinsic ligand exchange kinetics. The analysis also reveals that the response of the LC is triggered once the concentration of DMMP within the LC film rises to approximately 0.25 mM. By flowing a stream of gas free of DMMP over a LC film pre-exposed to DMMP, we established that the relaxation of the LC film to the initial state is also largely controlled by mass transport of the DMMP across the vapor side of the LC–vapor interface. Analysis of the relaxation of the system leads to an estimate of the sensitivity of the supported LC film to the concentration of DMMP in the gas phase (approximately 150 ppb for the non-optimized system reported in this paper). These results and others reported in this paper identify key physical phenomena that dictate the dynamics of adsorbate-induced ordering transitions in LC systems, and provide important guidance to the design of LCs as chemo-responsive materials for use in sensors.

dimethyl methylphosphonate↗

Multiple Sources of Riparian Wetland Suspended Solids during Episodic Rain Events: Influence on Uranium Transport

Suspended solids can be the primary vector for transporting contaminants in streams. The objective of this study was to determine whether changes in the properties of suspended solids during rain events impacted contaminant transport. Stream water was collected during five episodic events downstream from a U-contaminated wetland located in South Carolina, USA. The suspended particles were initially composed of Fe-flocs (particles formed in situ prior to the rain event) that had significantly greater Fe, Mn, organic-C, and U content than particles collected later during a sampling rain event. XANES and EXAFS revealed that U in the Fe-flocs was U(VI) and that it was not incorporated in a mineral structure but existed as inner- or outer-sphere adsorbed uranyl species associated with organic matter and Fe-oxides. The uranyl had an extraordinarily high affinity for the suspended solids, with solid to liquid U ratios of >72,000 (μg/kg)/(μg/L). After the initial flush of Fe-flocs, a greater fraction of the suspended solids had lower organic-C, Fe, Mn, and amorphous phases and were composed of more quartz, kaolinite, and gibbsite, resulting in lower U concentrations than those in the solids collected earlier in the rain event. This study highlights the importance of understanding suspended solids as transport vectors and their potential dynamic nature during rain events.

computer simulations↗

Streamflow in the Columbia River Basin: Quantifying Changes Over the Period 1951-2008 and Determining the Drivers of Those Changes

Trend, detection, and attribution analyses were performed using naturalized streamflow observations and routed land surface model runoff for 10 subbasins in the Columbia River Basin during water years 1951–2008. The Energy Exascale Earth System land-surface model (ELM) version 1.0 and the Routing Application for Parallel computatIon of Discharge (RAPID) routing model were used to conduct semi-factorial simulations driven by multiple sets of bias-corrected forcing data sets. Four main potential drivers, including climate change (CLMT), CO 2 concentration (CO 2 ), nitrogen deposition (NDEP), and land use and land cover change (LULCC), were analyzed during the assessment. All subbasins showed significant (α = 0.10) declines in the observed amount of annual total streamflow, except for the Middle and Upper Snake and Upper Columbia Subbasins. These declines were led by significant decreases in June–October streamflow, which also directly led to significant decreases in peak and summer streamflow. Except for the Snake River Subbasins, LULCC had the same pattern of declines in monthly streamflow, but the period was shifted to May–September. NDEP also had significant trends in June–October; however, rather than decreases, the trends showed significant increases in streamflow. While there were significant trends in CO 2 , NDEP, and LULCC, their signals of change were weak in comparison to the signal in CLMT and the natural internal variability found in streamflow. Overall, the detection and attribution analysis showed that the historical changes found in annual total, center of timing of, and summer mean streamflow could be attributed to changing climate and variability.

54 ENVIRONMENTAL SCIENCES↗

The metabolic regimes of 356 rivers in the United States

A national-scale quantification of metabolic energy flow in streams and rivers can improve understanding of the temporal dynamics of in-stream activity, links between energy cycling and ecosystem services, and the effects of human activities on aquatic metabolism. The two dominant terms in aquatic metabolism, gross primary production (GPP) and aerobic respiration (ER), have recently become practical to estimate for many sites due to improved modeling approaches and the availability of requisite model inputs in public datasets. We assembled inputs from the U.S. Geological Survey and National Aeronautics and Space Administration for October 2007 to January 2017. We then ran models to estimate daily GPP, ER, and the gas exchange rate coefficient for 356 streams and rivers across the continental United States. We also gathered potential explanatory variables and spatial information for cross-referencing this dataset with other datasets of watershed characteristics. Furthermore, this dataset offers a first national assessment of many-day time series of metabolic rates for up to 9 years per site, with a total of 490,907 site-days of estimates.

54 ENVIRONMENTAL SCIENCES↗

Islands in the stream: The effect of plasma flow on tearing stability

Reducing plasma flow clearly decreases the stability of tearing modes in multiple regimes (sawtooth, hybrid) in both high- and low-aspect-ratio tokamaks (DIII-D [J. L. Luxon, Nucl. Fusion 42, 614 (2002)], Joint European Torus [M. Keilhacker and the JET Team, Plasma Phys. Controlled Fusion 41, 301 (1999)], National Spherical Torus Experiment [M. Ono, S. M. Kaye, Y.-K. M. Peng, Nucl. Fusion 40, 557 (2000)], each with distinct means of lessening rotation). Further, reducing flow makes pre-existing 'saturated' islands larger at the same beta (beta). Thus lower plasma flow impairs high-beta operation owing both to the destabilization and to the impact of tearing-mode islands. Experimental results suggest that flow shear (not flow) at the tearing rational surface is classically stabilizing, making the effective tearing stability index DELTA{sup '} of the total current density profile more negative (more stable). In this picture, with profiles and all else the same, the minimum metastable beta at which neoclassical tearing modes (NTMs) can destabilize is proportional to -DELTA{sup '} and hence lower flow and flow shear lead to possible destabilization (depending on seeding) at lower beta. Similarly, if destabilized, the saturated NTM island width is proportional to -beta/DELTA{sup '} and thus increases as flow and flow shear are reduced. A working model gives a significant level of stabilizing shear if the plasma toroidal angular flow shear -dOMEGA{sub p}hi/dr at a given rational surface is of order of the inverse of the product of the local values of the parallel magnetic shear length L{sub s} and the Alfven time tau{sub A}. Experimental data are fitted for the effect of this normalization of flow shear in a simple empirical model for both onset and saturation of tearing modes. Most theoretical literature is on the consequence of flow shear on tearing stability at zero beta; tokamaks at high beta have large magnetic Prandtl number (an issue for the sign of the flow effect) and very large Lundquist number. It is in this regime that theory will be compared with experimentally based empirical models. The consequence for future tokamaks with low rotation may be lower tearing stability than now expected.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Characterizing counter-streaming interpenetrating plasmas relevant to astrophysical collisionless shocks

A series of Omega experiments have produced and characterized high velocity counter-streaming plasma flows relevant for the creation of collisionless shocks. Single and double CH{sub 2} foils have been irradiated with a laser intensity of {approx} 10{sup 16} W/cm{sup 2}. The laser ablated plasma was characterized 4 mm from the foil surface using Thomson scattering. A peak plasma flow velocity of 2000 km/s, an electron temperature of {approx} 110 eV, an ion temperature of {approx} 30 eV, and a density of {approx} 10{sup 18} cm{sup -3} were measured in the single foil configuration. Significant increases in electron and ion temperatures were seen in the double foil geometry. The measured single foil plasma conditions were used to calculate the ion skin depth, c/{omega}{sub pi}{approx}0.16 mm, the interaction length, Script-Small-L {sub int}, of {approx} 8 mm, and the Coulomb mean free path, {lambda}{sub mfp}{approx}27mm. With c/{omega}{sub pi} Much-Less-Than Script-Small-L {sub int} Much-Less-Than {lambda}{sub mfp}, we are in a regime where collisionless shock formation is possible.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗