Search NASA⌕ Search

SEARCH · Search NASA

Results for “structural materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Advanced composites structural concepts and materials technologies for primary aircraft structures: Structural response and failure analysis

Non-linear analysis methods were adapted and incorporated in a finite element based DIAL code. These methods are necessary to evaluate the global response of a stiffened structure under combined in-plane and out-of-plane loading. These methods include the Arc Length method and target point analysis procedure. A new interface material model was implemented that can model elastic-plastic behavior of the bond adhesive. Direct application of this method is in skin/stiffener interface failure assessment. Addition of the AML (angle minus longitudinal or load) failure procedure and Hasin's failure criteria provides added capability in the failure predictions. Interactive Stiffened Panel Analysis modules were developed as interactive pre-and post-processors. Each module provides the means of performing self-initiated finite elements based analysis of primary structures such as a flat or curved stiffened panel; a corrugated flat sandwich panel; and a curved geodesic fuselage panel. This module brings finite element analysis into the design of composite structures without the requirement for the user to know much about the techniques and procedures needed to actually perform a finite element analysis from scratch. An interactive finite element code was developed to predict bolted joint strength considering material and geometrical non-linearity. The developed method conducts an ultimate strength failure analysis using a set of material degradation models.

Dorris, William J.↗

Development of Metallic Sensory Alloys

Existing nondestructive evaluation (NDE) technologies are inherently limited by the physical response of the structural material being inspected and are therefore not generally effective at the identification of small discontinuities, making the detection of incipient damage extremely difficult. One innovative solution to this problem is to enhance or complement the NDE signature of structural materials to dramatically improve the ability of existing NDE tools to detect damage. To address this need, a multifunctional metallic material has been developed that can be used in structural applications. The material is processed to contain second phase sensory particles that significantly improve the NDE response, enhancing the ability of conventional NDE techniques to detect incipient damage both during and after flight. Ferromagnetic shape-memory alloys (FSMAs) are an ideal material for these sensory particles as they undergo a uniform and repeatable change in both magnetic properties and crystallographic structure (martensitic transformation) when subjected to strain and/or temperature changes which can be detected using conventional NDE techniques. In this study, the use of a ferromagnetic shape memory alloy (FSMA) as the sensory particles was investigated.

Wallace Terryl A.↗

Process Development and Testing for Lunar Habitats

Non-metallic solutions for Lunar bases are appealing due to their light weight and ability to block many forms of radiation. Composite materials made from different combinations of these non-metallic materials enable effective mating of dissimilar materials for strong structures such as pressurized habitats. Inserting and manufacturing composite structural materials on the Moon presents several challenges, however: the oxygen levels inside pressurized habitats will be relatively high, radiation that is blocked causes damage and the lack of atmosphere results in a high-magnitude negative pressure environment. In the past two years, the Materials and Processes Lab (EM01) invested in two internal research and development (IRAD) proposals for testing and procurement of composite materials. One proposal endeavors to determine flammability and radiation damage of various composite materials with a focus on carbon fiber and ultra-high molecular weight polyethylene (UHWMPE). The other proposal enables procurement of chopped fiber spray equipment materials which will be used to develop a novel technique for chopped UHMWPE fiber layup, similar to the chopped fiberglass layups used for making large structures such a boat hulls and hot tubs.

Composite↗

Metal segregation in hierarchically structured cathode materials for high-energy lithium batteries

In technologically important LiNi 1-x-y Mn x Co y O 2 cathode materials, surface reconstruction from a layered to a rock-salt structure is commonly observed under a variety of operating conditions, particularly in Ni-rich compositions. This phenomenon contributes to poor high-voltage cycling performance, impeding attempts to improve the energy density by widening the potential window at which these electrodes operate. Here, using advanced nano-tomography and transmission electron microscopy techniques, we show that hierarchically structured LiNi 0.4 Mn 0.4 Co 0.2 O 2 spherical particles, made by a simple spray pyrolysis method, exhibit local elemental segregation such that surfaces are Ni-poor and Mn-rich. The tailored surfaces result in superior resistance to surface reconstruction compared with those of conventional LiNi 0.4 Mn 0.4 Co 0.2 O 2 , as shown by soft X-ray absorption spectroscopy experiments. In conclusion, the improved high-voltage cycling behaviour exhibited by cells containing these cathodes demonstrates the importance of controlling LiNi 1-x-y Mn x Co y O 2 surface chemistry for successful development of high-energy lithium ion batteries.

36 MATERIALS SCIENCE↗

Molten Salt Corrosion Tests of Additively Manufactured Stainless Steel 316H

Molten salt reactors (MSRs) have drawn considerable interest due to their favorable safety features, high thermal efficiency, and compatibility with different fuel cycles. Yet, the success of MSRs hinges critically on the performance of structural materials to be used in these aggressive molten salt environments, where corrosion and material compatibility remain primary challenges to long-term reliability. Additively manufactured (AM) nuclear structural materials prompt the use of novel geometries and compositions to enhance material performance and reduce costs of constructing MSRs. The rapid solidification conditions inherent to AM processing impart distinctive microstructural features, including cellular sub-structures, dislocation densities, residual stress, and oxide inclusions, which can influence material performance in MSR components. While the mechanical properties of AM stainless steels have been widely studied, their corrosion behavior, particularly in molten salt environments, has received far less attention. Addressing these needs, the Advanced Materials and Manufacturing Technologies (AMMT) program provides a framework for systematically evaluating how unique microstructures produced by AM processes influence the performance of these materials in these demanding environments and for developing reproducible testing workflows that can support future code qualification efforts and standards development. Bridging this knowledge gap is essential for assessing the viability of AM alloys in MSRs and informing qualification strategies. A further challenge is the absence of standardized protocols for molten salt corrosion testing. Accordingly, this report provides an account of the corrosion evaluation of AM 316H stainless steel in NaCl 2 -MgCl 2 molten salt at 550 °C, with exposure times of 100 and 500 hours. It documents the experimental procedures implemented under the AMMT program, including salt preparation, exposure protocols, and post-test characterization methods, to establish reproducibility and transparency. Importantly, the study examines AM 316H samples in the as-fabricated condition, directly reflecting the surface state most relevant to engineering applications, and compares their behavior to machine-cut surfaces. Overall, preliminary evaluations have noted that surface conditions (e.g. morphology, contamination, etc.) have a noticeable impact on the corrosion resiliency. The impact of the corrosion is difficult to detect at 100h, unless, in the case of AM 316H, the specimen surface is decontaminated. After 500 h, as-fabricated surfaces of AM and wrought 316H display evidence of general versus preferential corrosion attack, respectively. Both AM and wrought 316H machine-cut surfaces exhibit a continuous Cr depletion zone, evident of general corrosion. While the estimated extent of corrosion appears within the same order of magnitude regardless of the surface condition, it is apparent that more predictable behavior is observed on machine-cut surfaces. Nonetheless, further investigation is necessary to fully elucidate the corrosion mechanism under these conditions.

36 - MATERIALS SCIENCE↗

History, present status, and future directions of vanadium alloys for fusion reactors

Since the need for low-activation fusion reactor materials was recognized in the mid-1980s, vanadium alloys have been researched and developed as promising candidates for blanket structural materials. Vanadium alloys are non-ferromagnetic and ductile materials and thus have advantages different from other candidates. However, since vanadium alloys are still at a premature industrial stage, research and development have been carried out not only on issues specific to fusion reactors but also on those related to industrial materials. Blankets using vanadium alloys as structural materials and liquid Li as a tritium breeder and coolant (self-cooled V/Li blankets) have unique characteristics, and research and development of issues specific to V/Li blankets have been conducted in conjunction with the development of vanadium alloys. In this paper, the progress of this research and development is reviewed, and the remaining issues are pointed out. As a result, the future direction of vanadium alloy research and development is discussed, considering recent changes in the environment surrounding fusion energy.

Liquid Li blanket↗

IER 517: Molybdenum Critical Experiment Design [Slides]

In nuclear fuels, U-Mo metallic fuels are used in new space reactor designs and new research reactor fuels. MITR, MURR, and NBSR reactors plan on converting from different HEU fuels to a U-Mo HALEU fuel. In spend nuclear fuel, 95 Mo is one of the 15 main absorbing fission products in irradiated LWR fuel. This makes it important for criticality safety studies in transportation and reprocessing. In structural materials. Molybdenum is found commonly in alloys that make up the structural materials of nuclear reactors such as type 316 SS. Molybdenum helps to improve high temperature performance and corrosion resistance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

In-situ Production of High Density Polyethylene and Other Useful Materials on Mars

This paper describes a revolutionary materials structure and power storage concept based on the in-situ production of abiotic carbon 4 compounds. One of the largest single mass penalties required to support the human exploration of Mars is the surface habitat. This proposal will use physical chemical technologies to produce high density polyethylene (HDPE) inflatable structures and construction materials from Mars atmospheric CO2. The formation of polyethylene from Mars CO2 is based on the use of the Sabatier and modified Fischer Tropsch reactions. The proposed system will fully integrate with existing in-situ propellant production concepts. The technology will also be capable of supplementing human caloric requirements, providing solid and liquid fuels for energy storage, and providing significant reduction in mission risk. The NASA Mars Reference Mission Definition Team estimated that a conventional Mars surface habitat structure would weigh 10 tonnes. It is estimated that this technology could reduce this mass by 80%. This reduction in mass will significantly contribute to the reduction in total mission cost need to make a Mars mission a reality. In addition the potential reduction of risk provided by the ability to produce C4 and potentially higher carbon based materials in-situ on Mars is significant. Food, fuel, and shelter are only three of many requirements that would be impacted by this research.

Flynn, Michael↗

Atom Probe Tomography for understanding microstructural and chemical changes in nuclear materials

Atom Probe Tomography (APT) is routinely employed to determine 3D microstructure and chemistry changes in structural materials used in reactor to understand irradiation effect. These findings help to correlate changes to mechanical and physical properties of nuclear materials which are subjected to extreme reactor conditions. With safety and economics of a reactor in mind, it is essential to be able to predict the changes in the fuel composition and microstructure as a function of burnup. Also, there is current need to develop advanced fuels with improved properties and performance which requires the experimental data on changes in microstructure, physical and chemical properties after irradiation for feedback process. A novel approach is presented to determine the local burnup in irradiated fuels using isotopic quantification obtained by Atom Probe Tomography (APT). Considering the volume of sample used (<100?µm3) for APT experiments using the lift-out process in a scanning electron microscope equipped with a Focused Ion Beam (FIB), the presented method determines the local burnup from a nuclear fuel, where a minimal amount of waste is produced. In this work, three samples were analyzed with different burnup conditions to quantify the isotopes of 235U, 236U, and 238U for burnup calculation in the irradiated metallic U–7Mo dispersion fuel. The calculated values were found in excellent agreement with MCNP calculations. With regard to structural materials, one of the primary factors limiting the utilization of fuel rods of Zr alloys is hydrogen pick up during oxidation. Past experimental studies have shown that the hydrogen pickup in Zirconium alloys is influenced by the alloy composition as well by irradiation temperature and neutron dose. Oftentimes, it is not feasible to carry out comprehensive studies on understanding the microstructural evolution in neutron irradiated materials since in reactor irradiation programs are extremely costly, lengthy and logistically complicated. The use of ion irradiation as a substitute has grown in recent years for several reasons including less radioactivity, faster irradiations and lower costs. In the framework of the MUZIC 3 project, samples of Zircaloy-4 have been proton and Zr2+ irradiated at the Michigan Ion Beam Lab (MIBL) facility with aim to create a microstructure that is similar to that observed after in-reactor service. The temperature of the environment is adjusted to compensate for the higher dose rate, as has been done previously. As a first step in this project the irradiated microstructures have been characterized using Transmission Electron Microscopy and Atom Probe Tomography to elucidate the microstructural changes, including precipitate amorphization and dissolution and the formation of dislocation loops. This presentation plans to highlight initial finding of this project.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Revisiting Multi-Material Composite Structures with Homogenized Composite Properties

Composite structures inherently develop residual stresses during their curing process. Driven predominately by mismatched thermal strains between differing materials or ply orientations, but also affected by curing process phenomena like polymer shrinkage, these residual stresses can lead to failure within composite structures. There are several methods varying in complexity that can be used to model the development of residual stresses, all of which are capable of capturing sufficient detail to understand the residual stress state at the ply level. However, explicitly modeling all plies of a layup in a composite structure can be prohibitively expensive based on the number of plies, structure size, and required element size. The computational cost can be reduced through the homogenization of the composite layup without losing much fidelity of the overall response of the structure. The homogenization process reduces the many plies of a laminate to a single lamina that reduces complexity and increases the mesh size where a single element can span multiple plies. This report focuses on verification and validation efforts for a homogenization process using a suite of finite element simulations rather than an analytic solution derived from classical laminate theory. Initial verification using representative element volumes indicated there was minimal error in the homogenization process; however, this compounded to a small, but acceptable error in strip and split ring experimental composite structures. The error does under predict the residual stress state in the strip and split ring and should be accounted for when simulating composite structures with homogenized properties.

36 MATERIALS SCIENCE↗

Grizzly Development for Light Water Reactor and Advanced Reactor Applications in Fiscal Year 2021

This report summarizes work performed during Fiscal Year (FY) 2021 at Idaho National Laboratory (INL) for the U.S. Department of Energy’s Nuclear Engineering Advanced Modeling and Simulation (NEAMS) program for the Structural Materials and Chemistry Technical Area in the work package entitled “MS-21IN050106 - Structural Materials - INL.” This effort mainly focused on development and application of capabilities for engineering-scale analysis of nuclear reactor structural components in the Grizzly and BlackBear codes. These efforts include performance improvements and application of models for high-temperature component response, cluster dynamics modeling of precipitation in light water reactor pressure vessel steel, engineering-scale capability development in the areas of concrete simulation and reactor pressure vessel analysis, and preparation for and conducting an independent assessment of the adherence of these codes to software quality standards.

36 MATERIALS SCIENCE↗

Response and representation of ductile damage under varying shock loading conditions in tantalum

The response of polycrystalline metals, which possess adequate mechanisms for plastic deformation under extreme loading conditions, is often accompanied by the formation of pores within the structure of the material. This large deformation process is broadly identified as progressive with nucleation, growth, coalescence, and failure the physical path taken over very short periods of time. These are well known to be complex processes strongly influenced by microstructure, loading path, and the loading profile, which remains a significant challenge to represent and predict numerically. In the current study, the influence of loading path on the damage evolution in high-purity tantalum is presented. Tantalum samples were shock loaded to three different peak shock stresses using both symmetric impact, and two different composite flyer plate configurations such that upon unloading the three samples displayed nearly identical “pull-back” signals as measured via rear-surface velocimetry. While the “pull-back” signals observed were found to be similar in magnitude, the sample loaded to the highest peak stress nucleated a connected field of ductile fracture which resulted in complete separation, while the two lower peak stresses resulted in incipient damage. The damage evolution in the “soft” recovered tantalum samples was quantified using optical metallography, electron-back-scatter diffraction, and tomography. These experiments are examined numerically through the use of a model for shock-induced porosity evolution during damage. The model is shown to describe the response of the tantalum reasonably well under strongly loaded conditions but less well in the nucleation dominated regime. As a result, numerical results are also presented as a function of computational mesh density and discussed in the context of improved representation of the influence of material structure upon macro-scale models of ductile damage.

36 MATERIALS SCIENCE↗

Large space structures - Structural concepts and materials

Large space structures will be a key element of the future space activities. They will include spacecraft such as the planned Space Station and large antenna/reflector structures for communications and observations. These large structures will exceed 100 m in length or 30 m in diameter. Concepts for construction of these spacecraft on orbit and their materials of construction provide some unique research challenges. This paper will provide an overview of the research in space construction of large structures including erectable and deployable concepts. Also, an approach to automated, on-orbit construction will be presented. Materials research for space applications focuses on high stiffness, low expansion composite materials that provide adequate durability in the space environment. The status of these materials research activities will be discussed.

Blankenship, Charles P.↗

International SAMPE Symposium and Exhibition, 31st, Los Angeles, CA, April 7-10, 1986, Proceedings

The present conference on the development status of advanced structural materials considers topics arising in such areas as automated structural manufacturing, advanced material and structure design techniques, environmental effects on materials, composite matrix processing, computer modeling for materials and processes, materials development trends in Europe and in Japan, fiber and whisker reinforcement development status, and novel thermoplastic materials and their applications. Also discussed are pressure-sensitive adhesive systems, materials suitable for space applications, polyimide resin systems, electronic materials, novel resin chemistries, ceramic and metallic systems, and the impact performance of state-of-the-art materials.

Bauer, J. L.↗

Optimizing the Binding Energy of Hydrogen on Nanostructured Carbon Materials through Structure Control and Chemical Doping

The DOE Hydrogen Sorption Center of Excellence (HSCoE) was formed in 2005 to develop materials for hydrogen storage systems to be used in light-duty vehicles. The HSCoE and two related centers of excellence were created as follow-on activities to the DOE Office of Energy Efficiency and Renewable Energy’s (EERE’s) Hydrogen Storage Grand Challenge Solicitation issued in FY 2003. The Hydrogen Sorption Center of Excellence (HSCoE) focuses on developing high-capacity sorbents with the goal to operate at temperatures and pressures approaching ambient and be efficiently and quickly charged in the tank with minimal energy requirements and penalties to the hydrogen fuel infrastructure. The work was directed at overcoming barriers to achieving DOE system goals and identifying pathways to meet the hydrogen storage system targets. To ensure that the development activities were performed as efficiently as possible, the HSCoE formed complementary, focused development clusters based on the following four sorption-based hydrogen storage mechanisms: 1. Physisorption on high specific surface area and nominally single element materials 2. Enhanced H2 binding in Substituted/heterogeneous materials 3. Strong and/or multiple H2 binding from coordinated but electronically unsatruated metal centers 4. Weak Chemisorption/Spillover. As a member of the team, our group at Duke studied the synthesis of various carbon-based materials, including carbon nanotubes and microporous carbon materials with controlled porosity. We worked closely with other team members to study the effect of pore size on the binding energy of hydrogen to the carbon –based materials. Our initial project focus was on the synthesis and purification of small diameter, single-walled carbon nanotubes (SWNTs) with well-controlled diameters for the study of their hydrogen storage properties as a function of diameters. We developed a chemical vapor deposition method that synthesized gram quantities of carbon nanotubes with average diameter size at less than 1 nm. However, initial tests performed at our collaborator’s lab at the National Renewable Energy Laboratory (NREL) did not indicate improved hydrogen sorption properties for the smaller-diameter nanotubes (compared with other types of nanotubes). As work continued, the difficulties in purification, large-scale synthesis, and stability of small diameter SWNTs became a major concern. In 2008, the Department of Energy (DOE) made a no-go decision on future applied R&D investment in pure, undoped, single-walled carbon nanotubes for vehicular hydrogen storage.2 The second phase of the project involved developing a low-cost and scalable approach for the synthesis of microporous carbon materials with well-controlled pore sizes that would be suitable for hydrogen storage. The team studied several approaches, including the use of different zeolites as a template, the use of organic micelle structures as a template, and the slow oxidation of polymer precursors. Among them, the slow activation of Polyether ether ketone (PEEK) under either CO2 environment or H2O vapor produced microporous carbon with an average pore size of less than 2 nm. Initial testing at 77K at both NREL and the California Institute of Technology (CalTech) showed that these materials can store ~5.1 wt% hydrogen (excess) at 40 bar and 77K. The main feature to note with this material is that while the excess gravimetric capacities (>5 wt% at 77K) and specific surface areas (>3100 m2/g) are similar to AX-21 and other “super activated” commercial carbon sorbents at the same temperatures and pressures, due to the smaller pore sizes, bulk densities greater than 0.7 g/ml can be achieved, enabling excess volumetric capacities greater than 35 g/L; more than double that of AX-21.

08 HYDROGEN↗

Strain-Induced asymmetry and on-site dynamics of silicon defects in graphene

In the last decade, the atomically-focused electron beams utilized in scanning transmission electron microscopes (STEMs) have been shown to induce a broad set of local structural transformations in materials, opening pathways for directing material synthesis and modification atom-by-atom. The mechanisms underlying these transformations remain largely unknown, due to the intractability of modeling the myriad of reaction pathways that can be accessed through high-energy electron scattering. The information on materials’ structure and dynamics that can be extracted from STEM images is similarly left underexplored. Here, we report the observation of anomalous on-site dynamics of individual silicon impurity atoms in graphene during STEM imaging. Density functional theory-based structural optimizations of anisotropically-strained molecular nanographenes reveal two distinct (but nearly degenerate) stable structures for four-fold coordinated silicon impurities, where interconversion between the two structures manifests slight changes of the silicon position within the lattice site. Implications for defect-based strain engineering in graphene are discussed.

36 MATERIALS SCIENCE↗