Search NASA⌕ Search

SEARCH · Search NASA

Results for “COMPRESSION BUCKLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

New Configuration for Compression-Test Fixture

Gravity-loades axial-compression test fixture is operated by raising lower platen and specimen against weighted upper platen. Wheel turns nut on threaded rod to move lower platen up or down. Limiting rods prevent further upward movement if sample buckles.

Shanks, G. C.↗

On the buckling of bars and plates in the plastic range. Part II

A review is made of existing literature concerning comparison with experiment of various theoretical formulas for buckling of plates in the plastic region. The significance and relative merits of various theories are discussed.

LOADS AND STRESSES, STRUCTURAL - COMPRESSION↗

Effect of impact damage on the compression strength of filamentary-composite hat-stiffened panels

An experimental investigation was conducted to evaluate the effect of low-velocity impact damage on the compression strength of filamentary-composite hat-stiffened panels. Twenty-four specimens of three design configurations fabricated from graphite-epoxy and boron-epoxy materials were tested. All three design configurations met the design buckling requirements in the undamaged condition. The impact damage was caused by firing aluminum spheres at the panels to simulate impact on aircraft from runway stones. Panels were damaged by impact in the hat cap or in the skin beneath the hat cap (regions of high axial stiffness) and in the skin between stiffeners (region of low axial stiffness). The panels were relatively insensitive to impact damage in the regions of low axial stiffness but were very sensitive to impact damage in the regions of high axial stiffness. Test results suggest that impact damage may be more dependent on the matrix properties than on the fiber properties of the composite materials considered.

Rhodes, M. D.↗

Subscale and Full-Scale Testing of Buckling-Critical Launch Vehicle Shell Structures

New analysis-based shell buckling design factors (aka knockdown factors), along with associated design and analysis technologies, are being developed by NASA for the design of launch vehicle structures. Preliminary design studies indicate that implementation of these new knockdown factors can enable significant reductions in mass and mass-growth in these vehicles and can help mitigate some of NASA s launch vehicle development and performance risks by reducing the reliance on testing, providing high-fidelity estimates of structural performance, reliability, robustness, and enable increased payload capability. However, in order to validate any new analysis-based design data or methods, a series of carefully designed and executed structural tests are required at both the subscale and full-scale level. This paper describes recent buckling test efforts at NASA on two different orthogrid-stiffened metallic cylindrical shell test articles. One of the test articles was an 8-ft-diameter orthogrid-stiffened cylinder and was subjected to an axial compression load. The second test article was a 27.5-ft-diameter Space Shuttle External Tank-derived cylinder and was subjected to combined internal pressure and axial compression.

Hilburger, Mark W.↗

The Effect of Initial Displacement of the Center Support on the Buckling of a Column Continuous over Three Supports

The test indicate that "an indiscriminate single application of the Southwell method (for analyzing Exp. Observations in problems of elastic stability)--can result in definite and measurable errors" The test also indicate "that the effect of curvature due to bending on the critical load for the compression flange material of a box beam is probably small and can be neglected." We have not found this to be true in our tests. It is believed that the effect of curvature, together with a small amount of fixity at the ribs, tends to force the stiffeners to bow in each bay thus effectively increasing their end fixity and thereby raising their allowable loads.

Lunquist, Eugene E.↗

Implementing Geometric Surface Imperfections into Sandwich Composite Cylinder Finite Element Method Models

The buckling responses of certain cylindrical shell structures are extremely sensitive to geometric imperfections. The NASA Engineering and Safety Center (NESC) Shell Buckling Knockdown Factor Project (SBKF) is conducting research to develop analysis-based buckling design recommendations. Experiments are used to verify the analysis-based factors, but the sensitivity of the test articles to geometric imperfections requires implementing as-manufactured imperfections into high-fidelity finite element method (FEM) models. Geometry measurement methods such as structured light scanning are used for all geometric surface data used in this work. Common preprocessing and visualization steps used in SBKF are discussed, and steps of how surface scans are prepared for implementation into a finite element model is described. The Python Tool for Implementing Geometric Imperfections in Reduced Structures (Py_TIGIRS), written specifically for the use with SBKF, is briefly described and uses eight functions to extract, modify, and write geometric imperfections into Abaqus input files. Results of the preprocessing methods and results from Py_TIGIRS are provided and compared for Composite Test Articles (CTA) 8.2, 8.2B, and 8.3. Excellent agreement between the visualized scan data and the FEM-extracted geometry is demonstrated. A brief example of why geometric surface imperfections are significant in nonlinear numerical analyses for thin cylinders in axial compression is provided as motivation to use tools such as Py_TIGIRS. Future developments of Py_TIGIRS including expansion to structures of arbitrary geometry is planned.

Geometric imperfections↗

The compressive failure of graphite/epoxy plates with circular holes

The results of an experimental investigation of the compressive behavior of T300/5203 graphite/epoxy laminated plates measuring 127.0 by 254.0 mm and containing circular holes ranging to 38.1 mm are reported. Two thicknesses, 24-ply and 48-ply, were chosen to differentiate between stability failures resulting from buckling and strength failures caused by the hole. Both quasi-isotropic and orthotropic stacking arrangements were used. The critical buckling load of the 24-ply panels was independent of hole size. Bifurcation occurred in the two half-wave mode longitudinally and one half-wave mode laterally in the quasi-isotropic panels. For the orthotropic 24-ply panels, bifurcation began in the one half-wave mode shape in each direction, but changed to the two half-wave mode before failure. Consistent post-buckling strength was exhibited by both laminated configurations. Panels with hole diameters below 3.175 mm displayed buckling before failure; those with holes larger than 6.35 mm experienced material failure around the hole before panel collapse.

Knauss, J. F.↗

Tests of Aluminum-alloy Stiffened-sheet Specimens Cut from an Airplane Wing

The specimens used in the present tests were cut from an actual airplane wing of the stressed-skin type. The specimens thus obtained were not representative of the usual type of laboratory specimens because the stiffeners were not exactly parallel nor evenly spaced and, in one case, the skin consisted of pieces of sheet of different thicknesses. The test data obtained indicate that the buckling strain of stiffened curved sheet can be computed with reasonable accuracy by the equation given by Wenzek. The ultimate loads of the specimens when tested as flat sheet were within +/-11 percent of the product of the compressive yield strength and the cross-sectional area of the stiffeners. A rivet spacing equal to 98 times the sheet thickness was a source of weakness, and rivet spacings up to 36 times the sheet thickness appeared satisfactory.

Holt, Marshall↗

Microstructural characterization of in situ MXCT images of high density foams under large strains

Foams are used in numerous applications, such as vibration damping and energy mitigation (e.g., packaging and helmets), wherein their mechanical properties are of critical importance. A typical compressive response of a high density elastomeric foam, shown in Fig 1, generally contains three regions of interest: (I) a linear-elastic region, governed by strut bending; (II) a relatively flat, or slowly increasing stress-strain response, accompanied by strut buckling and the localized collapse of pores; and (III) an exponentially increasing stress-strain curve wherein the collapse of the pore matrix leads to densification. Two material properties of interest, upon which considerable research has focused are the foam's Young's modulus, E{sub f}, defined as the slope of the stress-strain response in region I, and the collapse stress, {sigma}{sub f}, defined as the stress at which the response begins to deviate from linearity. It has been observed [1, 2, 3] that Young's modulus and the collapse stress are dependent on the material properties of the strut material and the non-dimensional relative-density of the foam, {rho}* = {rho}{sub f}/{rho}{sub m}, where {rho}{sub r} is the gross density of the foam and {rho}{sub m} is the density of the strut, or matrix, material. For foam of low relative-density, i.e, {rho}* < 0.1, the collapse stress and Young's modulus obey the relations {sigma}{sub c}/E{sub m} {proportional_to} ({rho}*){sup m} and E{sub f}/E{sub m} {proportional_to} ({rho}*){sup n} where E{sub m} is Young's modulus of the strut material and the bounds on the parameters m and n are 0.05 {le} m {le} 0.2 and 1 {le} n {le} 4 [4]. For open-celled foams, n = 2, whereas for closed-celled foams, n = 3. Theoretically, n = 1 for foams with an ''ideal strut'' configuration [6]. Foams of high relative-density ({rho}* > 0.1) require correcting terms to account for the axial contributions of the ''thick'' struts [5]. The above equations relate important foam properties to the relative-density of the foam; however, there exists a gap in the understanding of how the foam microstructure affects the mechanical response of the foam. This is due in large part to the difficulty of characterizing foam structures in 3D, especially foams of high relative-density. Most elastomeric foams are manufactured by the introduction of a gas into a cross-linking polymer. The developing foam microstructure has a complex dependence on the polymer viscosity and rate of polymerization, resulting in a randomly arranged pore structure with a large distribution of pore sizes. One approach is to characterize foam microstructures solely in terms of the cross-sectional shape and vector arrangement of the strut matrix, since it is this matrix that supports the stresses upon loading of the foam; yet as the density of a foam is increased, the very definition of what constitutes a strut brakes down. Another, perhaps easier to visualize, characterization of foam microstructure can come from a description of the pore shape and arrangement. Given the random nature of the microstructures of blown foam, both approaches are useful and valid. This paper describes our work aimed at linking the mechanical response and microstructural evolution of high relative-density foam as it undergoes large deformation. This work consists of several inter-related parts, including (i) measuring the compressive stress-strain response, as illustrated in Fig. 1, (ii) obtaining in situ micro X-ray computed tomography (MXCT) images of high relative-density foams undergoing large strains, and (iii) developing mathematical, computer aided, methodologies to perform image analysis and calculations of parameters that characterize the pores and struts. By using MXCT, a non-invasive technique for imaging the internal structure of materials, we are able to observe, internally, individual struts and pores as they undergo large deformation. Here we describe our computer aided image analysis methodologies and present examples of their application to the MXCT images of foams. Operations of the computer program include noise removal (smoothing), thresholding [7], edge detection [8], distance transformation [9, 10], pore detection via a Hough transformation [11], and skeletonization [12]. Strut parameters, such as the strut cross-sectional area and strut arrangement, are calculated from a skeleton-based model of the MXCT images. The Hough transform is a feature detection method used primarily in image analysis applications. We use this transform to detect and calculate pore parameters, such as pore arrangement and pore size distribution. The experiments and calculations are performed in order to develop data for the formulation of theory that links foam mechanical behavior specifically to the microstructure of high relative-density foams, not just simply to the relative-density of the foam.

36 MATERIALS SCIENCE↗

An experimental study of the strength and stability of thin monocoque shells with reinforced and unreinforced rectangular cutouts

Axial compression tests were run on eleven thin-walled aluminum cylinders having rectangular cutouts. Various types of reinforcement were used around the cutouts, and some tests were run with no reinforcement. The test results are compared with the cylinder buckling loads prior to installation of the cutouts (obtained without damaging the cylinder by using a buckle-capture technique), and correlated with computer-predicted failure loads. The latter were based on the use of the STAGS computer program. For thin cylinders such as these, the test and computer-based analysis shows that for small to moderate size cutouts, reinforcement of the cutout is of no benefit unless the cylinder is of extremely high (geometrical) quality. For cylinder quality and cutout size where reinforcement is beneficial, the relative merits of the various reinforcement configurations are discussed, and an empirical basis for design is proposed.

Holmes, A. M. C.↗

Implementing Geometric Surface Imperfections into Sandwich Composite Cylinder Finite Element Method Models

The buckling responses of certain cylindrical shell structures are extremely sensitive to geometric imperfections. The NASA Engineering and Safety Center (NESC) Shell Buckling Knockdown Factor Project (SBKF) is conducting research to develop analysis-based buckling design recommendations. Experiments are used to verify the analysis-based factors, but the sensitivity of the test articles to geometric imperfections requires implementing as-manufactured imperfections into high-fidelity finite element method (FEM) models. Geometry measurement methods such as structured light scanning are used for all geometric surface data used in this work. Common preprocessing and visualization steps used in SBKF are discussed, and steps of how surface scans are prepared for implementation into a finite element model is described. The Python Tool for Implementing Geometric Imperfections in Reduced Structures (Py_TIGIRS), written specifically for the use with SBKF, is briefly described and uses eight functions to extract, modify, and write geometric imperfections into Abaqus input files. Results of the preprocessing methods and results from Py_TIGIRS are provided and compared for Composite Test Articles (CTA) 8.2, 8.2B, and 8.3. Excellent agreement between the visualized scan data and the FEM-extracted geometry is demonstrated. A brief example of why geometric surface imperfections are significant in nonlinear numerical analyses for thin cylinders in axial compression is provided as motivation to use tools such as Py_TIGIRS. Future developments of Py_TIGIRS including expansion to structures of arbitrary geometry is planned.

Geometric imperfections↗

Eastern Ishtar Terra: Tectonic evolution derived from recognized features

Previous analyses have recognized several styles and orientations of compressional deformation, crustal convergence, and crustal thickening in Eastern Ishtar Terra. An east to west sense of crustal convergence through small scale folding, thrusting, and buckling is reflected in the high topography and ridge-and-valley morphology of Maxwell Montes and the adjacent portion of Fortuna Tessera. This east to west convergence was accompanied by up to 1000 km of lateral motion and large scale strike-slip faulting within two converging shear zones which has resulted in the present morphology of Maxwell Montes. A more northeast to southwest sense of convergence through large scale buckling and imbrication is reflected in large, northwest-trending scarps along the entire northern boundary of Ishtar Terra, with up to 2 km of relief present at many of the scarps. It was previously suggested that both styles of compression have occurred at the expense of pre-existing tessera regions which have then been overprinted by the latest convergence event. The difference in style is attributed mostly to differences in the properties of the crust converging with the tessera blocks. If one, presumably thick, tessera block converges with another tessera region, then the widespread, distributed style of deformation occurs, as observed in western Fortuna Tessera. However, if relatively thin crust (such as suggested for the North Polar Plains converges with thicker tessera regions, then localized deformation occurs, as reflected in the scarps along Northern Ishtar Terra. The purpose is to identify the types of features observed in Eastern Ishtar Terra. Their potential temporal and spatial relationships, is described, possible origins for them is suggested, and how the interpretation of some of these features has led to the multiple-style tectonic evolution model described is shown.

Vorderbruegge, R. W.↗

Buckling Tests with a Spar-rib Grill

The present report deals with a comparison of mathematically and experimentally defined buckling loads of a spar-rib grill, on the assumption of constant spar section, and infinitely closely spaced ribs with rigidity symmetrical to the grill center. The loads are applied as equal bending moments at both spar ends, as compression in the line connecting the joints, and in the spar center line as the assumedly uniformly distributed spar weight.

Weinhold, Josef↗

Applications of a damage tolerance analysis methodology in aircraft design and production

Objectives of customer mandated aircraft structural integrity initiatives in design are to guide material selection, to incorporate fracture resistant concepts in the design, to utilize damage tolerance based allowables and planned inspection procedures necessary to enhance the safety and reliability of manned flight vehicles. However, validated fracture analysis tools for composite structures are needed to accomplish these objectives in a timely and economical manner. This paper briefly describes the development, validation, and application of a damage tolerance methodology for composite airframe structures. A closed-form analysis code, entitled SUBLAM was developed to predict the critical biaxial strain state necessary to cause sublaminate buckling-induced delamination extension in an impact damaged composite laminate. An embedded elliptical delamination separating a thin sublaminate from a thick parent laminate is modelled. Predicted failure strains were correlated against a variety of experimental data that included results from compression after impact coupon and element tests. An integrated analysis package was developed to predict damage tolerance based margin-of-safety (MS) using NASTRAN generated loads and element information. Damage tolerance aspects of new concepts are quickly and cost-effectively determined without the need for excessive testing.

Woodward, M. R.↗

Structural Verification and Modeling of a Tension Cone Inflatable Aerodynamic Decelerator

Verification analyses were conducted on membrane structures pertaining to a tension cone inflatable aerodynamic decelerator using the analysis code LS-DYNA. The responses of three structures - a cylinder, torus, and tension shell - were compared against linear theory for various loading cases. Stress distribution, buckling behavior, and wrinkling behavior were investigated. In general, agreement between theory and LS-DYNA was very good for all cases investigated. These verification cases exposed the important effects of using a linear elastic liner in membrane structures under compression. Finally, a tension cone wind tunnel test article is modeled in LS-DYNA for which preliminary results are presented. Unlike data from supersonic wind tunnel testing, the segmented tension shell and torus experienced oscillatory behavior when subjected to a steady aerodynamic pressure distribution. This work is presented as a work in progress towards development of a fluid-structures interaction mechanism to investigate aeroelastic behavior of inflatable aerodynamic decelerators.

Tanner, Christopher L.↗