Search NASA⌕ Search

SEARCH · Search NASA

Results for “Computational Nuclear Engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Target Diagnostics Supports NIF's Path to Ignition

The physics requirements derived from the National Ignition Facility (NIF) experimental campaigns are leading to a wide variety of target diagnostics. Software development for the control and analysis of these diagnostics is included in the NIF Integrated Computer Control System, Diagnostic Control System and Data Visualization. These projects implement the configuration, controls, data analysis and visual representation of most of these diagnostics. To date, over 40 target diagnostics have been developed to support NIF experiments. In 2011 diagnostics were developed or enhanced to measure Ignition performance in a high neutron yield environment. Performance is optimized around four key variables: Adiabat (a) which is the strength and timing of four shocks delivered to the target, Velocity (V) of the imploding target, Mix (M) is the uniformity of the burn, and the Shape (S) of the imploding Deuterium Tritium (DT) hot spot. The diagnostics used to measure each of these parameters is shown in figure 1. Adiabat is measured using the Velocity Interferometer System for Any Reflector (VISAR) diagnostic consisting of three streak cameras. To provide for more accurate adiabat measurements the VISAR streak cameras were enhanced in FY11 with a ten comb fiducial signal controller to allow for post shot correction of the streak camera sweep non-linearity. Mix is measured by the Neutron Time of Flight (NTOF) and Radiochemical Analysis of Gaseous Samples (RAGS) diagnostics. To accommodate high neutron yield shots, NTOF diagnostic controls are being modified to use Mach Zehnder interferometer signals to allow the digitizers to be moved from near the target chamber to the neutron shielded diagnostic mezzanine. In December 2011 the first phase of RAGS diagnostic commissioning will be completed. This diagnostic will analyze the tracers that are added to NIF target capsules that undergo nuclear reactions during the shot. These gases are collected and purified for nuclear counting by the RAGS system. Three new instrument controllers were developed and commissioned to support this diagnostic. A residual-gas analyzer (RGA) instrument measures the gas content at various points in the system. The Digital Gamma Spectrometer instrument measures the radiological spectrum of the decaying gas isotopes. A final instrument controller was developed to interface to a PLC based Gas collection system. In order to support the implosion velocity measurements an additional Gated X-ray Detector (GXD) diagnostic was tested and commissioned. This third GXD views the target through a slit contained in its snout and allows the other GXD diagnostics to be used for measuring the shape on the same shot. In order to measure the implosion shape in a high neutron environment, Actide Readout In A Neutron Environment (ARIANE) and Neutron Imaging (NI) diagnostics were commissioned. The controls for ARIANE, a fixed port gated x-ray imager, contain a neutron shielded camera and micro channel plate pulser with its neutron sensitive electronics located in the diagnostic mezzanine. The NI diagnostic is composed of two Spectral Instruments SI-1000 cameras located 20M from the target and provides neutron images of the DT hot spot for high yield shots. The development and commissioning of these new or enhanced diagnostics in FY11 have provided meaningful insight that facilitates the optimization of the four key Ignition variables. In FY12 they will be adding three new diagnostics and enhancing four existing diagnostics in support of the continuing optimization series of campaigns.

42 ENGINEERING↗

On the Steady Mechanical Response of a Heterogeneous Fuel Plate

Herein, an exact solution for a heterogeneous, discontinuous wide-beam is developed having three unique boundary conditions sets. These boundary condition sets were chosen based on their relevance to plate-type fueled reactors. This solution, with respective boundary condition sets contributes new insights to the field of engineering mechanics as applied within the nuclear engineering discipline. Herein, the exact solution is validated under a set of test cases. A comparison is then made against other relations that have been developed to provide similar engineering insights. Lastly, the solution is applied toward a presently relevant engineering problem regarding the design of a monolithic plate-type fuel. The outcome of this work provides a solution form for the computation of out-of-plane deflection of a heterogeneous, discontinuous wide-beam that can be easily applied in engineering mechanics and is flexible in use.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

MCNP® Code Version 6.3.2 Theory & User Manual (Rev. 1)

This document acts as a repository of knowledge for the Monte Carlo N-Particle (MCNP) transport computer code. It is maintained alongside the source code and attempts to introduce new users and re-familiarize experienced users with the theory and practices of using the MCNP code for the wide range of particle transport analyses that it is appropriate for. The latest version of the MCNP code, version 6.3.2, provides the Monte Carlo particle transport community with the latest feature developments and bug fixes in the MCNP code. The MCNP code version 6.0 and later is also known as the MCNP6 code.

42 ENGINEERING↗

Verification of bubble tracking method and DNS examinations of single- and two-phase turbulent channel flows

Direct numerical simulation (DNS) has been regarded as a reliable data source for the development and validation of turbulence models along with experiments. The realization of DNS usually involves a very fine mesh that should be able to resolve all relevant turbulence scales down to Kolmogorov scale [1]. As the most computationally expensive approach compared to other CFD techniques, DNS applications used to be limited to flow studies at very low Reynolds numbers. Thanks to the tremendous growth of computing power over the past decades, the simulation capability of DNS has now started overlapping with some of the most challenging engineering problems. One of those examples in nuclear engineering is the turbulent coolant flow inside reactor cores. Coupled with interface tracking methods (ITM), the simulation capability of DNS can be extended to more complicated two-phase flow regimes. Departure from nucleate boiling (DNB) is the limiting critical heat flux phenomena for the majority of accidents that are postulated to occur in pressurized water reactors (PWR) [2]. As one of the major modeling and simulation (M&S) challenges pursued by CASL, the prediction capability is being developed for the onset of DNB utilizing multiphase-CFD (M-CFD) approach. DNS (coupled with ITM) can be employed to provide closure law information for the multiphase flow modeling at CFD scale. In the presented work, research groups at NCSU and UND will focus on applying different ITM to different geometries. Higher void fraction flow analysis at reactor prototypical conditions will be performed, and novel analysis methods will be developed, implemented and verified for the challenging flow conditions.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Some comments on turbulence modeling from an industrial perspective

In propulsion industry, computational techniques (namely computational fluid dynamics) are gradually becoming engineering design and analysis tools, especially in the case of high performance aircraft engines, high speed air breathing propulsion, rocket propulsion, and advanced nuclear propulsion and electric propulsion. The key issues in acceptance of CFD are turn around time, cost, and accuracy. The turn around time of analysis has to fit program schedules. Cost is still the bottom line, the value of CFD to the program should at least balance its cost. CFD can be used if it can be divided into two major parts: numerics and physical models.

Sindir, Munir M.↗

Direct Numerical Simulation of the Turbulent Flow Through PWR Spacer Grid and Mixing Vanes

Direct numerical simulation (DNS) has been regarded as a reliable data source for the development and validation of turbulence models along with experiments. The realization of DNS usually involves a very fine mesh that should be able to resolve all relevant turbulence scales down to Kolmogorov scale. As the most computationally expensive approach compared to other CFD techniques, DNS applications used to be limited to flow studies at very low Reynolds numbers. Thanks to the tremendous growth of computing power over the past decades, the simulation capability of DNS has now started overlapping with some of the most challenging engineering problems. One of those examples in nuclear engineering is the turbulent coolant flow inside reactor cores. In Light Water Reactor (LWR) cores, the nuclear fuel rods are arranged together as rod bundles in a triangular or square pattern. The fuel rod bundles are supported by the spacer grids. The mixing vanes are also installed to promote the turbulence intensity in coolant flow. An understanding of spacer grid and mixing vanes effect is important because it has a direct impact on the heat removal efficiency from the fuel rod surface. In the presented work, the DNS of turbulent flows are performed in three different types of geometries: (a) a regular Pressurized Water Reactor (PWR) subchannel; (b) a special PWR subchannel with reduced size spacer grid and mixing vanes (SGMV); (c) a special PWR subchannel with reduced size SGMV, but with a longer domain size. The springs and dimples of the spacer grid are not represented for the simplicity in the present investigation. The mean flow velocity and turbulent kinetic energy profiles are averaged from the instantaneous DNS data in different types of geometries as well as various downstream locations with respect to SGMV region. The results will help better assess the influence of spacer grid and mixing vanes on core coolant flows.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Status on the Component Models Developed in the Modelica Framework: High-Temperature Steam Electrolysis Plant & Gas Turbine Power Plant

This report has been prepared as part of an effort to design and build a modeling and simulation (M&S) framework to assess the economic viability of a nuclear-renewable hybrid energy system (N-R HES). In order to facilitate dynamic M&S of such an integrated system, research groups in multiple national laboratories have been developing various subsystems as dynamic physics-based components using the Modelica programming language. In fiscal year (FY) 2015, Idaho National Laboratory (INL) performed a dynamic analysis of two region-specific N-R HES configurations, including the gas-to-liquid (natural gas to Fischer-Tropsch synthetic fuel) and brackish water reverse osmosis desalination plants as industrial processes. In FY 2016, INL has developed two additional subsystems in the Modelica framework: a high-temperature steam electrolysis (HTSE) plant and a gas turbine power plant (GTPP). HTSE has been proposed as a high priority industrial process to be integrated with a light water reactor (LWR) in an N-R HES. This integrated energy system would be capable of dynamically apportioning thermal and electrical energy (1) to provide responsive generation to the power grid and (2) to produce alternative industrial products (i.e., hydrogen and oxygen) without generating any greenhouse gases. A dynamic performance analysis of the LWR/HTSE integration case was carried out to evaluate the technical feasibility (load-following capability) and safety of such a system operating under highly variable conditions requiring flexible output. To support the dynamic analysis, the detailed dynamic model and control design of the HTSE process, which employs solid oxide electrolysis cells, have been developed to predict the process behavior over a large range of operating conditions. As first-generation N-R HES technology will be based on LWRs, which provide thermal energy at a relatively low temperature, complementary temperature-boosting technology was suggested for integration with the HTSE process that requires higher temperature input. Simulation results involving several case studies show that the suggested control scheme could maintain the controlled variables (including the steam utilization factor, cathode stream inlet composition, and temperatures of the process streams at various locations) within desired limits under various plant operating conditions. The results also indicate that the proposed HTSE plant could provide operational flexibility to participate in energy management at the utility scale by dynamically optimizing the use of excess plant capacity within an N-R HES. A natural-gas fired GTPP has been proposed as a secondary energy supply to be included in an N-R HES. This auxiliary generator could be used to cover rapid dynamics in grid demand that cannot be met by the remainder of the N-R HES. To evaluate the operability and controllability of the proposed process during transients between load (demand) levels, the dynamic model and control design were developed. Special attention was given to the design of feedback controllers to regulate the power frequency, and exhaust gas and turbine firing temperatures. Several case studies were performed to investigate the system responses to the major disturbance (power load demand) in such a control system. The simulation results show that the performance of the proposed control strategies was satisfactory under each test when the GTPP experienced high rapid variations in the load.

08 HYDROGEN↗

A Combined Neutronic-Thermal Hydraulic Model of CERMET NTR Reactor

Abstract. Two different CERMET fueled Nuclear Thermal Propulsion reactors were modeled to determine the optimum coolant channel surface area to volume ratio required to cool a 25,000 lbf rocket engine operating at a specific impulse of 940 seconds. Both reactor concepts were computationally fueled with hexagonal cross section fuel elements having a flat-to-flat distance of 3.51 cm and containing 60 vol.% UO2 enriched to 93wt.%U235 and 40 vol.% tungsten. Coolant channel configuration consisted of a 37 coolant channel fuel element and a 61 coolant channel model representing 0.3 and 0.6 surface area to volume ratios respectively. The energy deposition from decelerating fission products and scattered neutrons and photons was determined using the MCNP monte carlo code and then imported into the STAR-CCM+ computational fluid dynamics code. The 37 coolant channel case was shown to be insufficient in cooling the core to a peak temperature of 3000 K; however, the 61 coolant channel model shows promise for maintaining a peak core temperature of 3000 K, with no more refinements to the surface area to volume ratio. The core was modeled to have a power density of 9.34 GW/m3 with a thrust to weight ratio of 5.7.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Perspective on Scalable AI on High-Performance Computing and Leadership Class Supercomputing Facilities [Industrial and Governmental Activities]

Many scientific applications that support the mission of the US Department of Energy (US-DoE) require modeling complex engineering and/or physical systems. Here, examples of such complex systems arise from: (a) materials science to develop new compounds with exceptional mechanical and thermodynamical properties (e.g., resistance to mechanical stresses and high temperatures), (b) structural and nuclear engineering to model the temporal evolution of the structural damage of concrete shields exposed to continuous neutron and gamma radiations emitted by the nuclear reactor core, (c) urban sciences (e.g., transportation and smart buildings), and (d) power grid systems.

97 MATHEMATICS AND COMPUTING↗

Release of a High Temperature Engineering Test Reactor (HTTR) Steady-State Multiphysics Model to the Virtual Test Bed

The National Reactor Innovation Center (NRIC) accelerates the demonstration and deployment of advanced nuclear energy through inspiring stakeholders and the public, empowering innovators, and delivering successful outcomes. The Virtual Test Bed (VTB) supports this mission by providing an open-source repository of advanced test reactor models for industry, academia, and the public to utilize. During my time at Idaho National Laboratory (INL), I: • Verified the input files of the High Temperature Engineering Test Reactor • Generated computational results • Created user documentation for the HTTR • Uploaded a steady-state HTTR model to the Virtual Test Bed • Authored a conference publication on the model

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Assessment of core damage frequency owing to possible fires at NPP with RBMK type reactors

According to Scientific and Technical Cooperation between the USA and Russia in the field of nuclear engineering the Idaho National Laboratory has transferred to the possession of the National Research Center ' Kurchatov Inst. ' the SAPHIRE software without any fee. With the help of the software Kurchatov Inst. developed a Pilot Living PSA- Model of Leningrad NPP Unit 1. Computations of core damage frequencies were carried out for additional Initiating Events. In the submitted paper such additional Initiating Events are fires in various compartments of the NPP. During the computations of each fire, structure of the PSA - Model was not changed, but Fault Trees for the appropriate systems, which are removed from service during the fire, were changed. It follows from the computations, that for ten fires Core Damaged Frequencies (CDF) are not changed. Other six fires will cause additional core damage. On the basis of the calculated results it is possible to determine a degree of importance of these fires and to establish sequence of performance of fire-prevention measures in various places of the NPP. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Validation of Scale 6.2 criticality calculations using KENO V.A and KENO-VI - 14603

SCALE 6.2 provides enhancements for criticality calculations relative to SCALE 6.1, especially with updated nuclear data libraries, resonance self-shielding options for multigroup (MG) calculations, and problem-dependent temperature treatments for continuous-energy (CE) calculations. Benchmark experiments from the International Criticality Safety Benchmark Evaluation Project that are available in the Oak Ridge National Laboratory Verified, Archived, Library of Inputs and Data (VALID) were applied in this validation effort to examine the impact of the SCALE 6.2 enhancements. Over 300 cases are drawn from the VALID library for testing KENO V.a, and a more limited set of approximately 50 configurations is used for validation of KENO-VI. A total of 401 unique critical experiments are used in this validation effort. In some cases, the KENO V.a models were converted to KENO-VI models so that the performance of both codes could be assessed for the same systems. Validation results for the SCALE 6.2 ENDF/B-VII.1 nuclear data libraries are presented, including MG neutron data in 56- and 252-group structures as well as CE data. The performance of all three multipurpose neutron libraries in calculating k{sub eff} is examined with critical experiment models covering a wide range of fuels, moderators, reflectors, absorbers, and neutron spectra. The SCALE 6.2 ENDF/B-VII.1 coupled neutron-photon library, primarily developed for shielding applications with 200 neutron groups and 47 gamma groups, provides additional energy resolution for fast systems relative to the MG neutron libraries which were developed to produce low biases for thermal neutron systems. The applicability of this library to criticality calculations for fast neutron spectrum systems is not investigated here but will be addressed in the final SCALE 6.2 validation report. The results of these calculations demonstrate that SCALE 6.2 generally provides lower biases than SCALE 6.1 and that the two versions of KENO provide equivalent results on the same suite of problems. SCALE 6.2 also includes an updated neutron cross-section covariance library based on the ENDF/B-VII.1 covariance data. The effect of these updated covariances on the uncertainty in k{sub eff} due to cross section uncertainties is also presented for some cases. A more thorough investigation of the updated covariance data is presented in a companion paper. (authors)

42 ENGINEERING↗

2012 SARA Students Technical Report

The Service Academy Research Associates (SARA) program provides an opportunity for Midshipmen and Cadets from US Service Academies to participate in research at Los Alamos National Laboratory (LANL), Lawrence Livermore National Laboratory (LLNL), and Sandia National Laboratory for several weeks during the summer as part of their summer training assignments. During the summer of 2012, three Midshipmen were assigned to work with the XCP Division at LANL for approximately 5-6 weeks. As one of the nation's top national security science laboratories, LANL stretches across 36 square miles, has over 2,100 facilities, and employs over 9,000 individuals including a significant number of students and postdocs. LANL's mission is to 'apply science and technology to: ensure the safety, security, and reliability of the US nuclear deterrent, reduce global threats, and solve other emerging national security challenges.' While LANL officially operates under the US Department of Energy (DoE), fulfilling this mission requires mutual cooperation with the US Department of Defense (DoD) as well. LANL's high concentration of knowledge and experience provides interns a chance to perform research in many disciplines, and its connection with the DoD in both operation and personnel gives SARA students insight to career possibilities both during and after military service. SARA students have plenty of opportunity to enjoy hiking, camping, the Los Alamos YMCA, and many other outdoor activities in New Mexico while staying at the Buffalo Thunder Resort, located 20 miles east of the lab. XCP Division is the Computational Physics division of LANL's Weapons Department. Working with XCP Division requires individuals to be Q cleared by the DoE. This means it is significantly more convenient for SARA students to be assigned to XCP Division than their civilian counterparts as the DoD CNWDI clearance held by SARA students is easily transferred to the lab prior to the students arriving at the start of the summer. SARA students working with XCP Division were given a comprehensive introduction into nuclear engineering and physics, nuclear weapons, and radiation transport and detection via texts and lectures at various classification levels. Students also attended tours of several prominent facilities at LANL including TA-41 Ice House, TA-55 PF-4 plutonium facility, the Nicholas C. Metropolis Center for Modeling and Simulation, also known as the Secure Computing Center (SCC), and the Dual-Axis Radiological Hydro Test (DARHT) facility; in addition, SARA students accompanied by LANL staff traveled to Minot AFB in North Dakota for tours of the 5th Bomb Wing and 91st Missile Wing facilities. Students participated in a week long class on the Monte Carlo N Particle (MCNP) code to supplement their understanding of radiation transport simulations. SARA students were then tasked with using this knowledge to model radiation detectors and use MCNP to compare their models to experimental data and previously accepted models.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Optical follow-up of gravitational wave triggers with DECam during the first two LIGO/VIRGO observing runs

Gravitational wave (GW) events detectable by LIGO and Virgo have several possible progenitors, including black hole mergers, neutron star mergers, black hole–neutron star mergers, supernovae, and cosmic string cusps. A subset of GW events is expected to produce electromagnetic (EM) emission that, once detected, will provide complementary information about their astrophysical context. To that end, the LIGO–Virgo Collaboration (LVC) sends GW candidate alerts to the astronomical community so that searches for their EM counterparts can be pursued. The DESGW group, consisting of members of the Dark Energy Survey (DES), the LVC, and other members of the astronomical community, uses the Dark Energy Camera (DECam) to perform a search and discovery program for optical signatures of LVC GW events. DESGW aims to use a sample of GW events as standard sirens for cosmology. Due to the short decay timescale of the expected EM counterparts and the need to quickly eliminate survey areas with no counterpart candidates, it is critical to complete the initial analysis of each night’s images as quickly as possible. We discuss our search area determination, imaging pipeline, and candidate selection processes. We review results from the DESGW program during the first two LIGO–Virgo observing campaigns and introduce other science applications that our pipeline enables.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

CHARACTERIZING AND MODELING FERRITE-CORE PROBES

In this paper, we accurately and carefully characterize a ferrite-core probe that is widely used for aircraft inspections. The characterization starts with the development of a model that can be executed using the proprietary volume-integral code, VIC-3D(c), and then the model is fitted to measured multifrequency impedance data taken with the probe in freespace and over samples of a titanium alloy and aluminum. Excellent results are achieved, and will be discussed.

36 MATERIALS SCIENCE↗