Search NASA⌕ Search

SEARCH · Search NASA

Results for “Correction Method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Application of Temperature Sensitivities During Iterative Strain-Gage Balance Calibration Analysis

A new method is discussed that may be used to correct wind tunnel strain-gage balance load predictions for the influence of residual temperature effects at the location of the strain-gages. The method was designed for the iterative analysis technique that is used in the aerospace testing community to predict balance loads from strain-gage outputs during a wind tunnel test. The new method implicitly applies temperature corrections to the gage outputs during the load iteration process. Therefore, it can use uncorrected gage outputs directly as input for the load calculations. The new method is applied in several steps. First, balance calibration data is analyzed in the usual manner assuming that the balance temperature was kept constant during the calibration. Then, the temperature difference relative to the calibration temperature is introduced as a new independent variable for each strain--gage output. Therefore, sensors must exist near the strain--gages so that the required temperature differences can be measured during the wind tunnel test. In addition, the format of the regression coefficient matrix needs to be extended so that it can support the new independent variables. In the next step, the extended regression coefficient matrix of the original calibration data is modified by using the manufacturer specified temperature sensitivity of each strain--gage as the regression coefficient of the corresponding temperature difference variable. Finally, the modified regression coefficient matrix is converted to a data reduction matrix that the iterative analysis technique needs for the calculation of balance loads. Original calibration data and modified check load data of NASA's MC60D balance are used to illustrate the new method.

Ulbrich, N.↗
NASA NTRS1993

Resolution of the COBE Earth sensor anomaly

Since its launch on November 18, 1989, the Earth sensors on the Cosmic Background Explorer (COBE) have shown much greater noise than expected. The problem was traced to an error in Earth horizon acquisition-of-signal (AOS) times. Due to this error, the AOS timing correction was ignored, causing Earth sensor split-to-index (SI) angles to be incorrectly time-tagged to minor frame synchronization times. Resulting Earth sensor residuals, based on gyro-propagated fine attitude solutions, were as large as plus or minus 0.45 deg (much greater than plus or minus 0.10 deg from scanner specifications (Reference 1)). Also, discontinuities in single-frame coarse attitude pitch and roll angles (as large as 0.80 and 0.30 deg, respectively) were noted several times during each orbit. However, over the course of the mission, each Earth sensor was observed to independently and unexpectedly reset and then reactivate into a new configuration. Although the telemetered AOS timing corrections are still in error, a procedure has been developed to approximate and apply these corrections. This paper describes the approach, analysis, and results of approximating and applying AOS timing adjustments to correct Earth scanner data. Furthermore, due to the continuing degradation of COBE's gyroscopes, gyro-propagated fine attitude solutions may soon become unavailable, requiring an alternative method for attitude determination. By correcting Earth scanner AOS telemetry, as described in this paper, more accurate single-frame attitude solutions are obtained. All aforementioned pitch and roll discontinuities are removed. When proper AOS corrections are applied, the standard deviation of pitch residuals between coarse attitude and gyro-propagated fine attitude solutions decrease by a factor of 3. Also, the overall standard deviation of SI residuals from fine attitude solutions decrease by a factor of 4 (meeting sensor specifications) when AOS corrections are applied.

Sedler, J.↗
NASA NTRS2004

Cirrus Clouds Optical, Microphysical and Radiative Properties Observed During Crystal-Face Experiment: I. A Radar-Lidar Retrieval System

A method of retrieving cloud microphysical properties using combined observations from both cloud radar and lidar is introduced. This retrieval makes use of an improvement to the traditional optimal estimation retrieval method, whereby a series of corrections are applied to the state vector during the search for an iterative solution. This allows faster convergence to a solution and is less processor intensive. The method is first applied to a synthetic cloud t o demonstrate its validity, and it is shown that the retrieval reliably reproduces vertical profiles of ice water content. The retrieval method is then applied to radar and lidar observations from the CRYSTAL-FACE experiment, and vertical profiles of ice crystal diameter, number concentration, and ice water content are retrieved for a cirrus cloud layers observed one day of that experiment. The validity of the relationship between visible extinction coefficient and radar reflectivity was examined. While synthetic tests showed such a functional relationship, the measured data only partially supported such a conclusion. This is due to errors in the forward model (as explained above) as well as errors in the data sets, including possible mismatch between lidar and radar profiles or errors in the optical depth. Empirical relationships between number concentrations and mean particle diameter were also examined. The results indicate that a distinct and robust relationship exists between these retrieved quantities and it is argued that such a relationship is more than an artifact of the retrieval process offering insight into the nature of the microphysical processes taking place in cirrus.

Mitrescu, C.↗
NASA NTRS2007

Asymptotic Energies and QED Shifts for Rydberg States of Helium

This paper reviews progress that has been made in obtaining essentially exact solutions to the nonrelativistic three-body problem for helium by a combination of variational and asymptotic expansion methods. The calculation of relativistic and quantum electrodynamic corrections by perturbation theory is discussed, and in particular, methods for the accurate calculation of the Bethe logarithm part of the electron self energy are presented. As an example, the results are applied to the calculation of isotope shifts for the short-lived 'halo' nucleus He-6 relative to He-4 in order to determine the nuclear charge radius of He-6 from high precision spectroscopic measurements carried out at the Argonne National Laboratory. The results demonstrate that the high precision that is now available from atomic theory is creating new opportunities to create novel measurement tools, and helium, along with hydrogen, can be regarded as a fundamental atomic system whose spectrum is well understood for all practical purposes.

Drake, G.W.F.↗
NASA NTRS1998

Formal Analysis of Human Automation Interaction: The Problem of Display Correctness

This presentation attempted to develop a quantitative method for evaluating the effectiveness of autoflight displays. Researchers sought to develop a methodology for evaluation of display correctness and develop a methodology for display synthesis. Topics covered included: mode awareness, industry/research contributions, human-machine interface analysis, research objectives, modeling, flight guidance project and evaluation.

Degani, Asaf↗
NASA NTRS1992

Computer program for calculating and fitting thermodynamic functions

A computer program is described which (1) calculates thermodynamic functions (heat capacity, enthalpy, entropy, and free energy) for several optional forms of the partition function, (2) fits these functions to empirical equations by means of a least-squares fit, and (3) calculates, as a function of temperture, heats of formation and equilibrium constants. The program provides several methods for calculating ideal gas properties. For monatomic gases, three methods are given which differ in the technique used for truncating the partition function. For diatomic and polyatomic molecules, five methods are given which differ in the corrections to the rigid-rotator harmonic-oscillator approximation. A method for estimating thermodynamic functions for some species is also given.

Mcbride, Bonnie J.↗
NASA NTRS1995

Initial vegetation species and senescience/stress indicator mapping in the San Luis Valley, Colorado using imaging spectrometer data

We analyzed AVIRIS data obtained over agricultural areas in the San Luis Valley of Colorado. The data were acquired on September 3, 1993. A combined method of radiative transfer modeling and ground calibration site reflectance was used to correct the flight data to surface reflectance. This method, called Radiative Transfer Ground Calibration, or RTGC, corrects for variable water vapor in the atmosphere and produces spectra free of artifacts with spectral channel to channel noise approaching the signal to noise of the raw data. The calibration site soil samples were obtained on the day of the overflight and measured on our laboratory spectrometer. The site was near the center of the AVIRIS scene and the spectra of the soil is spectrally bland, especially in the region of the chlorophyll absorption in the visible portion of the spectrum. The center of the scene is located at approximately 106 deg 03' longitude, 37 deg 23' latitude, and the scene covers about 92 square kilometers. This scene is one of 28 in the area for a general project to study the Summitville abandoned mine site, located in the mountains west of the San Luis Valley, and its effects on the surrounding environment.

Clark, Roger N.↗
NASA NTRS1981

Results of basic improvements to the extraction of spectra from IUE images

Results of two methods of extracting spectra from IUE images are compared. The first method, which is presently implemented, performs a geometric correction of the image followed by a photometric correction. The spectral data are then extracted using a slit with an effective width and sampling interval of 2.4A for the SWP camera and 3.7A for the LWR camera in low dispersion. The second method performs the photometric correction without doing a geometric correction. The spectral data are then extracted from the photometrically corrected image by an extraction slit, which follows the spectral orders in the nongeometrically corrected space, with an effective width and sampling interval 1/2 that of the present method.

Lindler, D. J.↗
NASA NTRS1984

Computation of viscous flow in planar and axisymmetric ducts by an implicit marching procedure

A streamwise marching procedure, approximately 200 times faster than a full Navier-Stokes procedure with comparable accuracy, is presented for solving problems of compressible viscous subsonic flow. Results are presented and compared with experimental data for the cases of developing turbulent flow in a circular pipe; turbulent flow in a two-dimensional S-duct; and turbulent flow in a typical subsonic diffuser. Prior to each main marching step, a preliminary marching step is taken in which the integral continuity equation and an uncoupled form of the streamwise momentum equation are solved simultaneously to obtain the viscous pressure correction. During the main marching step the equations for continuity, streamwise momentum, cross-flow momentum, and energy are solved simultaneously as a coupled system using an implicit finite-difference method, with the viscous pressure correction treated as a source term. The analysis may be used for flows with both favorable and adverse pressure gradients and to predict the location of flow separation.

Towne, C. E.↗
NASA NTRS2016

Temporal Gain Correction for X-Ray Calorimeter Spectrometers

Calorimetric X-ray detectors are very sensitive to their environment. The boundary conditions can have a profound effect on the gain including heat sink temperature, the local radiation temperature, bias, and the temperature of the readout electronics. Any variation in the boundary conditions can cause temporal variations in the gain of the detector and compromise both the energy scale and the resolving power of the spectrometer. Most production X-ray calorimeter spectrometers, both on the ground and in space, have some means of tracking the gain as a function of time, often using a calibration spectral line. For small gain changes, a linear stretch correction is often sufficient. However, the detectors are intrinsically non-linear and often the event analysis, i.e., shaping, optimal filters etc., add additional non-linearity. Thus for large gain variations or when the best possible precision is required, a linear stretch correction is not sufficient. Here, we discuss a new correction technique based on non-linear interpolation of the energy-scale functions. Using Astro-HSXS calibration data, we demonstrate that the correction can recover the X-ray energy to better than 1 part in 104 over the entire spectral band to above 12 keV even for large-scale gain variations. This method will be used to correct any temporal drift of the on-orbit per-pixel gain using on-board calibration sources for the SXS instrument on the Astro-H observatory.

X-ray detector X-ray spectrometer X-ray calorimete↗
NASA NTRS1993

Microwave Scattering Model for Grass Blade Structures

In this paper, the electromagnetic scattering solution for a grass blade with complex cross-section geometry is considered. It is assumed that the blade cross section is electrically small, but its length is large compared to the incident wavelength. In a recent study it has been shown that the scattering solution for such problems, in the form of a polarizability tensor, can be obtained using the low-frequency approximation in conjunction with the method of moments. In addition, the study shows that the relationship between the polarizability tensor of a dielectric cylinder and its dielectric constant can be approximated by a simple algebraic expression. The results of this study are used to show that this algebraic approximation is valid also for cylinders with cross sections the shape of grass blades, providing that proper values am selected for each of three constants appearing in the expression. These constants are dependent on cylinder shape, and if the relationship between the constants and the three parameters describing a grass blade shape can be determined, an algebraic approximation relating polarizability tensor to blade shape, as well as dielectric constant, can be formed. Since the elements of the polarizability tensor are dependent on only these parameters, this algebraic approximation can replace the cumbersome method of moments model. A conjugate gradient method is then implemented to correctly determine the three constants of the algebraic approximation for each blade shape. A third-order polynomial fit to the data is then determined for each constant, thus providing a complete analytic replacement to the numerical (moment method) scattering model. Comparisons of this approximation to the numerical model show an average error of less than 3%.

Stiles, James M.↗
NASA NTRS2012

Impacts of Cross-Platform Vicarious Calibration on the Deep Blue Aerosol Retrievals for Moderate Resolution Imaging Spectroradiometer Aboard Terra

The retrieval of aerosol properties from spaceborne sensors requires highly accurate and precise radiometric measurements, thus placing stringent requirements on sensor calibration and characterization. For the Terra/Moderate Resolution Imaging Spedroradiometer (MODIS), the characteristics of the detectors of certain bands, particularly band 8 [(B8); 412 nm], have changed significantly over time, leading to increased calibration uncertainty. In this paper, we explore a possibility of utilizing a cross-calibration method developed for characterizing the Terral MODIS detectors in the ocean bands by the National Aeronautics and Space Administration Ocean Biology Processing Group to improve aerosol retrieval over bright land surfaces. We found that the Terra/MODIS B8 reflectance corrected using the cross calibration method resulted in significant improvements for the retrieved aerosol optical thickness when compared with that from the Multi-angle Imaging Spectroradiometer, Aqua/MODIS, and the Aerosol Robotic Network. The method reported in this paper is implemented for the operational processing of the Terra/MODIS Deep Blue aerosol products.

Jeong, Myeong-Jae↗
NASA NTRS2012

Modifications Of Discrete Ordinate Method For Computations With High Scattering Anisotropy: Comparative Analysis

A numerical accuracy analysis of the radiative transfer equation (RTE) solution based on separation of the diffuse light field into anisotropic and smooth parts is presented. The analysis uses three different algorithms based on the discrete ordinate method (DOM). Two methods, DOMAS and DOM2+, that do not use the truncation of the phase function, are compared against the TMS-method. DOMAS and DOM2+ use the Small-Angle Modification of RTE and the single scattering term, respectively, as an anisotropic part. The TMS method uses Delta-M method for truncation of the phase function along with the single scattering correction. For reference, a standard discrete ordinate method, DOM, is also included in analysis. The obtained results for cases with high scattering anisotropy show that at low number of streams (16, 32) only DOMAS provides an accurate solution in the aureole area. Outside of the aureole, the convergence and accuracy of DOMAS, and TMS is found to be approximately similar: DOMAS was found more accurate in cases with coarse aerosol and liquid water cloud models, except low optical depth, while the TMS showed better results in case of ice cloud.

Korkin, Sergey V.↗
NASA NTRS1987

Finite Element Flux-Corrected Transport (FEM-FCT) for the Euler and Navier-Stokes equations

A high resolution finite element method for the solution of problems involving high speed compressible flows is presented. The method uses the concepts of flux-corrected transport and is presented in a form which is suitable for implementation on completely unstructured triangular or tetrahedral meshes. Transient and steady state examples are solved to illustrate the performance of the algorithm.

Loehner, Rainald↗
NASA NTRS1987

Finite element flux-corrected transport (FEM-FCT) for the Euler and Navier-Stokes equations

A high resolution finite element method for the solution of problems involving high speed compressible flows is presented. The method uses the concepts of flux-corrected transport and is presented in a form which is suitable for implementation on completely unstructured triangular or tetrahedral meshes. Transient and steady-state examples are solved to illustrate the performance of the algorithm.

Lohner, Rainald↗
NASA NTRS1988

Calculations of transonic flows with shocks using Newton's method and direct solver. II - Solution of Euler equations

Transonic flows with shocks are simulated using steady Euler equations and by simultaneously solving the resulting nonlinear algebraic equations using Newton's method. At each iteration, a direct solver computes the corrections and the process is repeated until convergence is achieved. The corrections and errors are reduced quadratically with the present method, allowing solutions of machine accuracy to be obtained in a few steps. Nonunique inviscid solutions and nonunique solutions of the Navier Stokes equations for quasi-one-dimensional flows in nozzles are presented. Calculations are also presented for steady two-dimensional inviscid flows around a cylinder in the transonic regime.

Hafez, M.↗
NASA NTRS1989

High resolution flow field prediction for tail rotor aeroacoustics

The prediction of tail rotor noise due to the impingement of the main rotor wake poses a significant challenge to current analysis methods in rotorcraft aeroacoustics. This paper describes the development of a new treatment of the tail rotor aerodynamic environment that permits highly accurate resolution of the incident flow field with modest computational effort relative to alternative models. The new approach incorporates an advanced full-span free wake model of the main rotor in a scheme which reconstructs high-resolution flow solutions from preliminary, computationally inexpensive simulations with coarse resolution. The heart of the approach is a novel method for using local velocity correction terms to capture the steep velocity gradients characteristic of the vortex-dominated incident flow. Sample calculations have been undertaken to examine the principal types of interactions between the tail rotor and the main rotor wake and to examine the performance of the new method. The results of these sample problems confirm the success of this approach in capturing the high-resolution flows necessary for analysis of rotor-wake/rotor interactions with dramatically reduced computational cost. Computations of radiated sound are also carried out that explore the role of various portions of the main rotor wake in generating tail rotor noise.

Quackenbush, Todd R.↗
NASA NTRS1994

Understanding the relation between wind- and pressure-driven sea level variability

Sea surface adjustment to combined wind and pressure forcing is examined using numerical solutions to the shallow water equations. The experiments use coastal geometry and bottom topography representative of the North Atlantic and are forced by realistic barometric pressure and wind stress fields. The repsonse to pressure is essentially static or close to the inverted barometer solution at periods longer than a few days and dominates the sea level variability, with wind-driven sea level signals being relatively small. With regard to the dynamic signals, wind-driven fluctuations dominate at long periods, as expected from quasi-geostrophic theory. Pressure becomes more important than wind stress as a source of dynamic signals only at periods shorter than approximately three days. Wind- and pressure-driven sea level fluctuations are anticorrelated over most regions. Hence, regressions of sea level on barometric pressure yield coefficients generally smaller than expected for the inverted barometer response known to be the case in the model. In the regions of significant wind-pressure correlation effects, to infer the correct pressure reponse using statistical methods, input fields must include winds as well as pressure. Because of the nonlocal character of the wind response, multivariate statistical models with local wind driving as input are not very successful. Inclusion of nonlocal wind variability over extensive regions is necessary to extract the correct pressure response. Implications of these results to the interpretation of sea level observations are discussed.

Ponte, Rui M.↗