Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diffusion bonding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Influences of superalloy composition and Pt content on the oxidation behavior of gamma–gamma prime NiPtAl bond coatings

Here, the effects of superalloy composition and Pt content on the high-temperature oxidation behavior of γ–γ’ NiPtAl diffusion coatings were investigated over the temperature range of 1050–1150 °C. Simple NiPtAl diffusion coatings with 7 or 12 µm electroplated Pt thickness were evaluated in 1-h cycles in dry O 2 for up to 2500 cycles on four superalloys: directionally solidified (DS) alloy 142, 1st generation single-crystal (SX) alloy 1483, and 2nd generation SX alloys X4 and N5. Coatings on high-Hf alloy 142 experienced severe internal oxidation of Hf at all temperatures. Coatings on ~5 at.% Ti alloy 1483 were protective at 1050 °C, but exhibited severe scale spallation at 1100 °C, with extensive formation of Ti- and Ni-rich oxides at the gas interface. Coatings with 7-µm Pt on X 4 were extremely protective at 1100 °C, but failed rapidly at 1150 °C, which also was associated with the formation of Ti-rich oxides. Increasing the coating Pt content on X 4 improved the 1150 °C oxidation behavior. Coatings on Ti-free N 5 showed the best performance at 1150 °C, especially with 12-µm Pt. Although γ–γ’ coatings can exhibit outstanding cyclic oxidation resistance with minimal Al depletion, they appear to be sensitive to substrate composition, as well as eventual Pt depletion due to interdiffusion.

36 MATERIALS SCIENCE↗

Hydrogen plasma treatments for passivation of amorphous-crystalline silicon-heterojunctions on surfaces promoting epitaxy

The impact of post-deposition hydrogen plasma treatment (HPT) on passivation in amorphous/crystalline silicon (a-Si:H/c-Si) interfaces is investigated. Combining low temperature a-Si:H deposition and successive HPT, a high minority carrier lifetime >8 ms is achieved on c-Si <100>, which is otherwise prone to epitaxial growth and thus inferior passivation. It is shown that the passivation improvement stems from diffusion of hydrogen atoms to the heterointerface and subsequent dangling bond passivation. Concomitantly, the a-Si:H hydrogen density increases, leading to band gap widening and void formation, while the film disorder is not increased. Thus, HPT allows for a-Si:H band gap and a-Si:H/c-Si band offset engineering.

36 MATERIALS SCIENCE↗

Network analysis of proton transfer in liquid water

Proton transfer in macromolecular systems is a fascinating yet elusive process. In the last ten years, molecular simulations have shown to be a useful tool to unveil the atomistic mechanism. Notwithstanding, the large number of degrees of freedom involved make the accurate description of the process very hard even for the case of proton diffusion in bulk water. Here, multi-state empirical valence bond molecular dynamics simulations in conjunction with complex network analysis are applied to study proton transfer in liquid water. Making use of a transition network formalism, this approach takes into account the time evolution of several coordinates simultaneously. Our results provide evidence for a strong dependence of proton transfer on the length of the hydrogen bond solvating the Zundel complex, with proton transfer enhancement as shorter bonds are formed at the acceptor site. We identify six major states (nodes) on the network leading from the “special pair” to a more symmetric Zundel complex required for transferring the proton. Moreover, the second solvation shell specifically rearranges to promote the transfer, reiterating the idea that solvation beyond the first shell of the Zundel complex plays a crucial role in the process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electron-phonon coupling and superconductivity in the doped topological crystalline insulator ( Pb 0.5 Sn 0.5 ) 1 – x In x Te

Here, we present a neutron-scattering study of phonons in single crystals of ( Pb 0.5 Sn 0.5 ) 1 – x In x Te with x = 0 (metallic, but nonsuperconducting) and x = 0.2 (nonmetallic normal state, but superconducting). We map the phonon dispersions (more completely for x = 0 ) and find general consistency with theoretical calculations, except for the transverse and longitudinal optical (LO) modes at the Brillouin-zone center. At low temperature, both modes are strongly damped but sit at a finite energy ( ≈ 4 meV in both samples), shifting to higher energy at room temperature. These modes are soft due to a proximate structural instability driven by the sensitivity of Pb-Te and Sn-Te p -orbital hybridization to off-center displacements of the metal atoms. The impact of the soft optical modes on the low-energy acoustic modes is inferred from the low thermal conductivity, especially at low temperature. Given that the strongest electron-phonon coupling is predicted for the LO mode, which should be similar for both studied compositions, it is intriguing that only the In-doped crystal is superconducting. In addition, we observe elastic diffuse (Huang) scattering that is qualitatively explained by the difference in Pb-Te and Sn-Te bond lengths within the lattice of randomly distributed Pb and Sn sites. We also confirm the presence of anomalous diffuse low-energy atomic vibrations that we speculatively attribute to local fluctuations of individual Pb atoms between off-center sites.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Defect state passivation at III-V oxide interfaces for complementary metal–oxide–semiconductor devices

The paper describes the reasons for the greater difficulty in the passivation of interface defects of III–V semiconductors like GaAs. These include the more complex reconstructions of the starting surface which already possess defect configurations, the possibility of injecting As antisites into the substrate which give rise to gap states, and the need to avoid As-As bonds and As dangling bonds which give rise to gap states. The nature of likely defect configurations in terms of their electronic structure is described. The benefits of diffusion barriers and surface nitridation are discussed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

EBR-II Superheater Duplex Tube Examination

After 30 years of operation, the Experimental Breeder Reactor II (EBR-II) Superheater 710 at Argonne National Laboratory-West (now Idaho National Laboratory) was decommissioned. As part of its post-service examination, four duplex tube sections were removed and Charpy impact testing was performed to characterize the crack arresting ability of nickel-bonded tube interfaces. Scanning electron microscopy (SEM) examination was also performed to characterize and identify changes in bond material microstructure. From room temperature to 400 degrees C, all samples demonstrated ductility and crack-stopping ability similar to that exhibited by beginning-of-life samples. However, at low temperature (-5 degrees C), samples removed from the lower region of the superheater (near the sodium inlet) failed while those from the upper region (near the sodium outlet) did not. SEM analysis revealed that all the tube-tube interfaces showed evidence of iron diffusion into the nickel braze, which resulted in the formation of a multiphase diffusion structure. Yet, significant void formation was only observed in the bond layer of the tubes removed from the lower region. This may be due to a change in the crystal microstructure of one of the phases within the bond layer that occurs in the 350 to 450 degrees C temperature range, which results in a lower density and the formation of porosity. Apparently, only the samples from the higher temperature region were exposed to this transition temperature, and the resulting large voids that developed acted as stress concentrators that led to low-temperature embrittlement and failure of the Charpy impact specimens.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Water Dynamics in Nanoporous Silica: Ultrafast Vibrational Spectroscopy and Molecular Dynamics Simulations

Nanoporous silica materials are important in catalysis, energy, and materials applications in which water is an essential component. System performance is intimately connected to the water dynamics occurring in the confined environment. However, the dynamics and associated structures of water in nanoporous silica have proven challenging to measure and predict. Here, confined water dynamics are examined via the ultrafast infrared spectroscopy of selenocyanate (SeCN – ) dissolved in the hydrated ~2.4 nm silica mesopores of MCM41. Polarization selective pump–probe and two-dimensional infrared measurements on the CN stretching mode of SeCN – are used to probe the effect of confinement on orientational relaxation and spectral diffusion dynamics. Here, the dynamics of SeCN – provide information on the surrounding water hydrogen bond dynamics. The long CN stretch lifetime (~36 ps), relative to the water hydroxyl stretch (<2 ps), significantly extends the time scales that can be accessed. Complete orientational relaxation (C 2 (t), orientational correlation function) and spectral diffusion (C ω (t), frequency–frequency correlation function) dynamics are presented and compared to the simulated time correlation functions in a model silica pore of the same size. A slow decay component not present in the bulk liquid is observed in both experiments, indicating that the hydrogen bond dynamics are significantly altered by confinement. The simulations reveal a qualitative difference in the functional dependence of C 2 (t;d) and C ω (t;d) on d, the distance from the interface. The former becomes exponentially faster with distance while the latter makes an abrupt transition from slower to faster dynamics midway between the surface and pore center, d ≅ 6 Å.

14 SOLAR ENERGY↗

Proton Solvation and Transport in Hydrated Nafion

Proton solvation properties and transport mechanisms have been studied in hydrated Nafion using the self-consistent multistate empirical valence bond (SCI-MS-EVB) method that includes the effects excess proton charge defect delocalization and Grotthuss proton hopping. It was found that sulfonate groups influence excess proton solvation, as well as the proton hydration structure, by stabilizing a more Zundel-like (H 5 O 2 + ) structure in their first solvation shells. Hydrate proton-related hydrogen bond networks were observed to be more stable than networks with water alone. Diffusion rates, Arrhenius activation energies, and transport pathways were calculated and analyzed to characterize the nature of the proton transport. Diffusion rate analysis suggests that a proton-hopping mechanism dominates the proton transport for the studied water loading levels and that there is a clear degree of anticorrelation with the vehicular transport. The activation energy drops quickly with an increasing water content when the water loading level is smaller than ~10 H 2 O/SO 3 – , which is consistent with experimental observations. The sulfonate groups were also found to affect the proton hopping directions. The temperature and water content effects on the proton transport pathways were also investigated.

Feng, Shulu↗

Molecular dynamics study of two-dimensional sum frequency generation spectra at vapor/water interface

Two-dimensional heterodyne-detected vibrational sum frequency generation (2D HD-VSFG) spectra at vapor/water interface were studied by molecular dynamics (MD) simulation with a classical flexible and nonpolarizable model. The present model well describes the spectral diffusion of 2D infrared spectrum of bulk water as well as 2D HD-VSFG at the interface. The effect of isotopic dilution on the 2D HD-VSFG was elucidated by comparing the normal (H{sub 2}O) water and HOD water. We further performed decomposition analysis of 2D HD-VSFG into the hydrogen-bonding and the dangling (or free) OH vibrations, and thereby disentangled the different spectral responses and spectral diffusion in the 2D HD-VSFG. The present MD simulation demonstrated the role of anharmonic coupling between these modes on the cross peak in the 2D HD-VSFG spectrum.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Diffusion of copolymers composed of monomers with drastically different friction factors in copolymer/homopolymer blends

Copolymers are commonly used as interface modifiers that allow for the compatibilization of polymer components in a blend. For copolymers to function as a compatibilizer, they must diffuse through the matrix of the blend to the interface between the two blend components. The diffusivity of a copolymer in a blend matrix therefore becomes important in determining good candidates for use as compatibilizers. In this paper, coarse-grained Monte Carlo simulations using the bond fluctuation model modified with an overlap penalty have been developed to study the diffusive behavior of PS/PMMA random copolymers in a PMMA homopolymer blend. The simulations vary the connectivity between different monomers, the thermodynamic interactions between the monomers which manifest within a chain, and between copolymer and homopolymer matrix and define the monomer friction coefficient of each component independently, allowing for the determination of the combined effect of these parameters on copolymer chain diffusion. Finally, the results of this work indicate that PS-r-PMMA copolymer diffusion is not linearly dependent on the copolymer composition on a logarithmic scale, but its diffusion is a balance of the kinetics governed by the dominant motion of the faster styrene monomers and thermodynamics, which are governed by the concentration of styrene monomer within a given monomer’s local volume.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The effect of hydrogen-bonding on flavin’s infrared absorption spectrum

Cluster and continuum solvation computational models are employed to model the effect of hydrogen bonding interactions on the vibrational modes of lumiflavin. Calculated spectra were compared to experimental Fourier-transform infrared (FTIR) spectra in the diagnostic 1450–1800 cm –1 range, where intense V C=C , V C=N , V C 2 =O , and V C 4 =O stretching modes of flavin’s isoalloxazine ring are found. Local mode analysis is used to describe the strength of hydrogen-bonding in cluster models. The computations indicate that V C=C and V C=N mode frequencies are relatively insensitive to intermolecular interactions while the V C 2 =O and V C 4 =O modes are sensitive to direct (and also indirect for V C 2 =O ) hydrogen-bonding interactions. Although flavin is neutral, basis sets without the diffuse functions provide incorrect relative frequencies and intensities. The 6-31+G* basis set is found to be adequate for this system, and there is limited benefit to considering larger basis sets. Calculated vibrational mode frequencies agree with experimentally determined frequencies in solution when cluster models with multiple water molecules are used. Accurate simulation of relative FTIR band intensities, on the other hand, requires a continuum (or possibly quantum mechanical/molecular mechanical) model that accounts for long-range electrostatic effects. Lastly, an experimental peak at ca. 1624 cm –1 that is typically assigned to the V C 2 =O vibrational stretching mode has a complicated shape that suggests multiple underlying contributions. Our calculations show that this band has contributions from both the C 6 –C 7 and C 2 = O stretching vibrations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hot Isostatic Press Can Optimization for Aluminum Cladding of U-10Mo Reactor Fuel Plates: FY12 Final Report and FY13 Update

Currently, the proposed processing path for low enriched uranium – 10 wt. pct. molybdenum alloy (LEU-10Mo) monolithic fuel plates for high power research and test reactors includes hot isostatic pressing (HIP) to bond the aluminum cladding that encapsulates the fuel foil. Initial HIP experiments were performed at Idaho National Laboratory (INL) on approximately ¼ scale “mini” fuel plate samples using a HIP can design intended for these smaller experimental trials. These experiments showed that, with the addition of a co-rolled zirconium diffusion barrier on the LEU-10Mo alloy fuel foil, the HIP bonding process is a viable method for producing monolithic fuel plates. Further experimental trials at Los Alamos National Laboratory (LANL) effectively scaled-up the “mini” can design to produce full-size fuel prototypic plates. This report summarizes current efforts at LANL to produce a HIP can design that is further optimized for higher volume production runs. The production-optimized HIP can design goals were determined by LANL and Babcock & Wilcox (B&W) to include maintaining or improving the quality of the fuel plates produced with the baseline scaled-up mini can design, while minimizing material usage, improving dimensional stability, easing assembly and disassembly, eliminating machining, and significantly reducing welding. The initial small-scale experiments described in this report show that a formed-can approach can achieve the goals described above. Future work includes scaling the formed-can approach to full-size fuel plates, and current progress toward this goal is also summarized here.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Water Chain Formation on TiO{sub 2}(110)

The adsorption of water on a reduced rutile TiO{sub 2}(110)-(1×1) surface has been investigated using scanning tunneling microscopy (STM) and density functional theory (DFT) calculations. The STM measurements show that at a temperature of 50 K, an isolated water monomer adsorbs on top of a Ti(5f) atom on the Ti row in agreement with earlier studies. As the coverage increases, water molecules start to form one-dimensional chain structures along the Ti row direction. Supporting DFT calculations show that the formation of an H-bonded one-dimensional water chain is energetically favorable compared to monomer adsorption. In the chain, there are H-bonds between adjacent water molecules, and the water molecules also form H-bonds to neighboring bridging oxygens of TiO{sub 2}(110). Thermal annealing at T = 190 K leads to the formation of longer chains facilitated by the diffusion of water on the surface. The results provide insight into the nature of the hydrogen bonding in the initial stage of wetting of TiO{sub 2}.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An Inorganic-Rich Solid Electrolyte Interphase for Advanced Lithium-Metal Batteries in Carbonate Electrolytes

In carbonate electrolytes, the organic-inorganic solid electrolyte interphase (SEI) formed on the lithium (Li) metal anode surface is strongly bonded to Li and experiences the same volume change as Li, thus it undergoes continuous cracking/reformation during plating/stripping cycles. Here we report, an inorganic-rich SEI is designed on a Li metal surface to reduce its bonding energy with Li metal by dissolving 4 M concentrated LiNO 3 in dimethyl sulfoxide (DMSO) as an additive for a fluoroethylene carbonate (FEC) based electrolyte. Due to the aggregate structure of NO 3 - ions and its participation in the primary Li + solvation sheath, abundant Li 2 O, Li 3 N, and LiN x O y grains are formed in the resulting SEI, in addition to the uniform LiF distribution from the reduction of PF 6 - ions. The inorganic-rich SEI’s weak bonding (high interface energy) to Li can effectively promote Li diffusion along the SEI/Li interface and prevent Li dendrite penetration into the SEI. As a result, our designed carbonate electrolyte enables a Li anode to achieve a high Li plating/stripping CE of 99.55% (1 mA cm -2 , 1.0 mAh cm -2 ) and the electrolyte also enables a Li||LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NMC811) full cell (2.5 mAh cm -2 ) to retain 75%of its initial capacity after 200 cycles with an outstanding CE of 99.83%.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The potential application of VS 2 as an electrode material for Mg ion battery: A DFT study

Herein, by means of first-principle calculations based on density functional theory (DFT), the electrochemical properties of monolayer VS 2 (M-VS 2 ), double-layer VS 2 (D-VS 2 ) and bulk VS 2 (B-VS 2 ) as electrode materials for Mg-ion batteries (MIBs) were comprehensively explored. The computation results reveal that Mg atom can strongly bind with the three different forms of VS 2 . All of the Mg adsorbed VS 2 systems demonstrate metallic characteristics, which indicates a good electronic conductivity. In addition, crystal orbital hamiltonian population shows that the stability of V-S bond is weakened after adsorption of Mg atom. The low diffusion barriers of Mg give rise to the high rate performance of VS 2 in MIBs. More interestingly, the three types of VS 2 display same storage ability for Mg cations, which can adsorb 0.5 Mg atoms for VS 2 , producing maximum theoretical capacity 233 mA h g -1 for MIBs. Furthermore, the average working voltages results suggest that M-VS 2 can be employed as anode materials, while D-VS 2 , B-VS 2 can be used as cathode materials for MIBs.

25 ENERGY STORAGE↗

Microstructural characterization and mechanical properties of a novel TiC-based cermet bonded with Ni3(Al,Ti) and NiAl duplexalloy

A novel TiC/Ni{sub 3}(Al,Ti)-NiAl composite has been designed and synthesized by in-situ reactive hot-pressing a mixture of Ti{sub 3}AlC{sub 2} and Ni powders. After hot-press sintering at 1500 °C and 30 MPa, almost fully dense composite was obtained and the in-situ formed TiC grains were well-bonded with Ni{sub 3}(Al,Ti) and NiAl alloys. Due to the nanolaminated structure in Ti{sub 3}AlC{sub 2} materials that weakly bonded Al layers are more prone to be out-diffused from Ti{sub 3}AlC{sub 2} lattice than that of Ti atoms. The deintercalated AlTi atoms would react with Ni to give rise to the formation of Ni{sub 3}(Al,Ti) and NiAl alloys, and meanwhile a crystal lattice structure transformation happened from hexagonal Ti{sub 3}AlC{sub 2} to cubic lattice TiC. The formation of phases, grains morphologies, sintering behavior and mechanical properties were associated with sintering temperature. The as prepared TiC/Ni{sub 3}(Al,Ti)-NiAl composite under 1500 °C exhibited superior mechanical properties comparing with the counterparts fabricated under 1350 °C and 1400 °C because of the enhanced microstructures and eliminations of pores. Hardness, flexural strength and fracture toughness of the TiC/Ni{sub 3}(Al,Ti)-NiAl composite at room temperature were determined as 9.9 ± 0.35 GPa, 665 ± 26 MPa and 10.23 ± 0.4 MPa·m{sup 1/2}, respectively. Interestingly, the flexural strength and fracture toughness increases with temperature rising from 600 to 800 °C, the maximum of flexural strength and fracture toughness could reach 775 ± 25 MPa and 11.6 ± 0.4 MPa·m{sup 1/2} at 800 °C.

36 MATERIALS SCIENCE↗

Li 2 GeS 3 : Lithium Ionic Conductor with an Unprecedented Structural Type

Lithium-ion batteries (LIBs) are widely used in electric vehicles, mobile electronic devices, and large-scale stationary energy storage systems. However, their liquid electrolytes present significant safety concerns due to their inherent flammability. To address this, the focus has shifted toward all-solid-state batteries (ASSBs) utilizing inorganic solid electrolytes that promise enhanced safety. In this work, we report the discovery of a new crystal structural type of Li-ion conductor, Li 2 GeS 3 , with a unique structure, synthesized by a solid-state reaction from Li 2 S and GeS 2 . It was first reported in 2000 with an orthorhombic unit cell, but its detailed crystal structure remains veiled. Here, we have unveiled its structure for the first time, employing an ab initio structure determination technique from powder X-ray and time-of-flight neutron diffraction data. The compound has an unprecedented crystal structural type with a hexagonal $P6_1$ symmetry and a unit cell of α = 6.79364(4) Å and c = 17.90724(14) Å. Its structure is comprised of a distorted hexagonal close-packed arrangement of sulfur anions with three asymmetric metal atoms: Li1, Li2, and Ge are in tetrahedral cavities surrounded by sulfur atoms. The ionic conductivity of Li 2 GeS 3 was measured to be 1.63 × 10 –8 S cm –1 at 303 K and 2.45 × 10 –7 S cm –1 at 383 K. Bond valence energy landscape calculations revealed three-dimensional lithium diffusion pathways within the structure. This novel crystal structure in Li 2 GeS 3 holds the potential for developing high-performance ionic conductors through suitable chemical substitution and offers valuable insights into designing new ionic conductors for ASSBs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗