Search NASA⌕ Search

SEARCH · Search NASA

Results for “Directed Evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Importance of filter’s microstructure in dynamic filtration modeling of gasoline particulate filters (GPFs): Inhomogeneous porosity and pore size distribution

The state-of-the-art multiscale modeling of GPFs including channel scale, wall scale, and pore scale is described. The microstructures of two GPFs were experimentally characterized. The pore size distributions of the GPFs were determined by mercury porosimetry. The porosity was measured by X-ray computed tomography (CT) and found to be inhomogeneous across the substrate wall. The significance of pore size distribution with respect to filtration performance was analyzed. The predictions of filtration efficiency were improved by including the pore size distribution in the filtration model. A dynamic heterogeneous multiscale filtration (HMF) model was utilized to simulate particulate filtration on a single channel particulate filter with realistic particulate emissions from a spark-ignition direct-injection (SIDI) gasoline engine. The dynamic evolution of filter’s microstructure and macroscopic filtration characteristics including mass- and number-based filtration efficiencies and pressure drop were predicted and discussed. The microstructure of the GPF substrate including inhomogeneous porosity and pore size distribution is found to significantly influence local particulate deposition inside the substrate and macroscopic filtration performance and is recommended to be resolved in the filtration model to simulate and evaluate the filtration performance of GPFs.

Environmental Molecular Sciences Laboratory↗

Research on the noise produced by large scale structure in supersonic jets

Using a dual electrode glow discharge excitation device, a method of mode selection into either the n = 0 or n = + or - 1 azimuthal modes was developed and tested by Fourier analyzing experimental azimuthal phase and amplitude data. On a M = 2.1 moderate Reynolds number (Re = 68,000) jet with a laminar boundary layer, under n = 0 or n = +1 excitation, coherent axial wave evolution, mean flow, and sound pressure level directivity measurements were performed. The boundary layer of this same jet was excited usng a grit coating on the nozzle wall, and bandpassed axial wave evolution data obtained and compared to the masurements made by previous workers on a conventional high Reynolds number jet (Re = 5,000,000) using a hot-film type probe.

Mclaughlin, D. K.↗

Evolution Of Lattice Structure And Chemical Composition Of The Surface Reconstruction Layer In Li1.2Ni0.2Mn0.6O2 Cathode Material For Lithium Ion Batteries

Voltage and capacity fading of layer structured lithium and manganese rich (LMR) transition metal oxide is directly related to the structural and composition evolution of the material during the cycling of the battery. However, understanding such evolution at atomic level remains elusive. Based on atomic level structural imaging, elemental mapping of the pristine and cycled samples and density functional theory calculations, it is found that accompanying the hoping of Li ions is the simultaneous migration of Ni ions towards the surface from the bulk lattice, leading to the gradual depletion of Ni in the bulk lattice and thickening of a Ni enriched surface reconstruction layer (SRL). Furthermore, Ni and Mn also exhibit concentration partitions within the thin layer of SRL in the cycled samples where Ni is almost depleted at the very surface of the SRL, indicating the preferential dissolution of Ni ions in the electrolyte. Accompanying the elemental composition evolution, significant structural evolution is also observed and identified as a sequential phase transition of C2/m →I41→Spinel. For the first time, it is found that the surface facet terminated with pure cation is more stable than that with a mixture of cation and anion. These findings firmly established how the elemental species in the lattice of LMR cathode transfer from the bulk lattice to surface layer and further into the electrolyte, clarifying the long standing confusion and debate on the structure and chemistry of the surface layer and their correlation with the voltage fading and capacity decaying of LMR cathode. Therefore, this work provides critical insights for designing of cathode materials with both high capacity and voltage stability during cycling.

Environmental Molecular Sciences Laboratory↗

Environmentally induced chemical and morphological heterogeneity of zinc oxide thin films

Zinc oxide (ZnO) thin films have been reported to suffer from degradation in electrical properties, when exposed to elevated heat and humidity, often leading to failures of electronic devices containing ZnO films. This degradation appears to be linked to water and oxygen penetration into the ZnO film. However, a direct observation in the ZnO film morphological evolution detailing structural and chemical changes has been lacking. Here, we systematically investigated the chemical and morphological heterogeneities of ZnO thin films caused by elevated heat and humidity, simulating an environmental aging. X-ray fluorescence microscopy, X-ray absorption spectroscopy, grazing incidence small angle and wide angle X-ray scattering, scanning electron microscopy (SEM), ultra-high-resolution SEM, and optical microscopy were carried out to examine ZnO and Al-doped ZnO thin films on two different substrates—silicon wafers and flexible polyethylene terephthalate (PET) films. In the un-doped ZnO thin film, the simulated environmental aging is resulting in pin-holes. In the Al-doped ZnO thin films, significant morphological changes occurred after the treatment, with an appearance of platelet-shaped structures that are 100–200 nm wide by 1μm long. Synchrotron x-ray characterization further confirmed the heterogeneity in the aged Al-doped ZnO, showing the formation of anisotropic structures and disordering. X-ray diffraction and X-ray absorption spectroscopy indicated the formation of a zinc hydroxide in the aged Al-doped films. In conclusion, utilizing advanced characterization methods, our studies provided information with an unprecedented level of details and revealed the chemical and morphologically heterogeneous nature of the degradation in ZnO thin films.

36 MATERIALS SCIENCE↗

Environment-induced entanglement with a single photon

We propose an all-optical setup, which couples different degrees of freedom of a single photon, to investigate entanglement generation by a common environment. The two qubits are represented by the photon polarization and Hermite-Gauss transverse modes, while the environment corresponds to the photon path. For an initially two-qubit separable state, the increase of entanglement is analyzed as the probability of an environment-induced transition ranges from 0 to 1. An entanglement witness that is invariant throughout the evolution of the system yields a direct measurement of the concurrence of the two-qubit state.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Theoretical Reflectance Spectra of Earth-like Planets through Their Evolutions: Impact of Clouds on the Detectability of Oxygen, Water, and Methane with Future Direct Imaging Missions

In the near-future, atmospheric characterization of Earth-like planets in the habitable zone will become possible via reflectance spectroscopy with future telescopes such as the proposed LUVOIR and HabEx missions. While previous studies have considered the effect of clouds on the reflectance spectra of Earth-like planets, the molecular detectability considering a wide range of cloud properties has not been previously explored in detail. In this study, we explore the effect of cloud altitude and coverage on the reflectance spectra of Earth-like planets at different geological epochs and examine the detectability of O{sub 2},H{sub 2}O, and CH{sub 4} with test parameters for the future mission concept, LUVOIR, using a coronagraph noise simulator previously designed for WFIRST-AFTA. Considering an Earth-like planet located at 5 pc away, we have found that for the proposed LUVOIR telescope, the detection of the O{sub 2} A-band feature (0.76 μm) will take approximately 100, 30, and 10 hr for the majority of the cloud parameter space modeled for the atmospheres with 10%, 50%, and 100% of modern Earth O{sub 2} abundances, respectively. In particular, for the case of ≳50% of modern Earth O{sub 2} abundance, the feature will be detectable with an integration time ≲10 hr as long as there are lower-altitude (≲8 km) clouds with a global coverage of ≳20%. For the 1% of the modern Earth O{sub 2} abundance case, however, it will take more than 100 hr for all the cloud parameters we modeled.

79 ASTRONOMY AND ASTROPHYSICS↗

A particle astrophysics magnet facility: ASTROMAG

The primary scientific objectives of ASTROMAG are to: examine cosmological models by searching for antimatter and dark matter candidates; study the origin and evolution of matter in the galaxy by direct sampling of galactic matter; and study the origin and acceleration of the relativistic particle plasma in the galaxy and its effects on the dynamics and evolution of the galaxy. These general scientific objectives will be met by ASTROMAG with particle detection instruments designed to make the following observations: search, for anti-nuclei of helium and heavier element; measure the spectra of anti-protons and positrons; measure the isotopic composition of cosmic ray nuclei at energies of several GeV/amu; and measure the energy spectra of cosmic ray nuclei to very high energies.

Ormes, Jonathan F.↗

Simulating non-native cubic interactions on noisy quantum machines

As a milestone for general-purpose computing machines, we demonstrate that quantum processors can be programed to efficiently simulate dynamics that are not native to the hardware. Moreover, on noisy devices without error correction, we show that simulation results are significantly improved when the quantum program is compiled using modular gates instead of a restricted set of standard gates. We demonstrate the general methodology by solving a cubic interaction problem, which appears in nonlinear optics, gauge theories, as well as plasma and fluid dynamics. To encode the non-native Hamiltonian evolution, we decompose the Hilbert space into a direct sum of invariant subspaces in which the nonlinear problem is mapped to a finite-dimensional Hamiltonian simulation problem. Furthermore, in a three-states example, the resultant unitary evolution is realized by a product of approximately 20 standard gates, using which approximately ten simulation steps can be carried out on state-of-the-art quantum hardware before results are corrupted by decoherence. In comparison, the simulation depth is improved by more than an order of magnitude when the unitary evolution is realized as a single cubic gate, which is compiled directly using optimal control. Alternatively, parametric gates may also be compiled by interpolating control pulses. Modular gates thus obtained provide high-fidelity building blocks for quantum Hamiltonian simulations.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Strain stabilized nickel hydroxide nanoribbons for efficient water splitting

Development of efficient and durable oxygen evolution reaction (OER) catalysts has a direct impact on water splitting efficiency and cost effectiveness. In this work, we report the successful synthesis of a new Ni(OH) 2 structure, strain-stabilized Ni(OH) 2 nanoribbons (NR-Ni(OH) 2 ) two to three layers thick, with widths of 2-5 nm, via an electro-oxidation route. Conventional Ni(OH) 2 usually has negligible OER activity, while NR-Ni(OH) 2 shows a high activity for the oxygen evolution reaction, an overpotential of 162 millivolts and furthermore exhibits long-term stability in alkaline electrolyte. The substantial reduction in overpotential of NR-Ni(OH) 2 is due to its easier OOH* adsorption by the active four-coordinated Ni edge sites. The enhanced catalytic activity of NR-Ni(OH) 2 makes it an excellent candidate for industrial applications.

36 MATERIALS SCIENCE↗

A new apparatus for the concurrent measurement of friction and permeability evolution in fault gouge

Here we introduce a new miniature double direct shear (mini-DDS) apparatus, housed within a standard-triaxial (TEMCO) pressure vessel, capable of concurrently measuring the evolution of frictional strength, stability, healing and along-fault permeability under in situ conditions of stress and temperature. The apparatus accommodates gouge samples (25 mm × 32 mm) and intact rock samples with confining and shear stresses and pore pressures up to ~26 MPa. Permeability may be measured with applied flow rates ranging from 1.67 × 10 -11 to 3.6 × 10 -6 m 3 /s to a flow accuracy of 0.5% representing a lower bound of permeability >2.2 × 10 -18 m 2 . Sliding velocities are in the range 0.1 μm/s to 0.67 cm/s with a frame stiffness of 0.067 kN/μm. We describe protocols and procedures for calibration and experiments and note the potential of the apparatus for both rapid and extended-duration measurements of friction-permeability evolution and healing. The apparatus returns measurements of friction and stability of reference materials of F110 quartz consistent with the literature while additionally allowing the concurrent measurement of permeability. Permeability of F110 quartz evolves in slide-hold-slide (SHS) experiments with increases during holds and decreases during subsequent slides. These observations are consistent with grain crushing and resultant wear products that reduce that permeability by clogging during slides with unclogging of the major fluid channels occurring during shearing.

58 GEOSCIENCES↗

Inner heliospheric evolution of a 'STEALTH' CME derived from multi-view imaging and multipoint in situ observations. I. Propagation to 1 AU

Coronal mass ejections (CMEs) are the main driver of space weather. Therefore, a precise forecasting of their likely geo-effectiveness relies on an accurate tracking of their morphological and kinematical evolution throughout the interplanetary medium. However, single viewpoint observations require many assumptions to model the development of the features of CMEs. The most common hypotheses were those of radial propagation and self-similar expansion. The use of different viewpoints shows that, at least for some cases, those assumptions are no longer valid. From radial propagation, typical attributes that can now be confirmed to exist are over-expansion and/or rotation along the propagation axis. Understanding the 3D development and evolution of the CME features will help to establish the connection between remote and in situ observations, and hence help forecast space weather. We present an analysis of the morphological and kinematical evolution of a STEREO-B-directed CME on 2009 August 25-27. By means of a comprehensive analysis of remote imaging observations provided by the SOHO, STEREO, and SDO missions, and in situ measurements recorded by Wind, ACE, and MESSENGER, we prove in this paper that the event exhibits signatures of deflection, which are usually associated with changes in the direction of propagation and/or also with rotation. The interaction with other magnetic obstacles could act as a catalyst of deflection or rotation effects. We also propose a method to investigate the change of the CME tilt from the analysis of height-time direct measurements. If this method is validated in further work, it may have important implications for space weather studies because it will allow for inference of the interplanetary counterpart of the CME's orientation.

79 ASTRONOMY AND ASTROPHYSICS↗

Phase Transformations among TiO2 Polymorphs

Polymorphs widely exist in nature and synthetic systems and are well known to determine material properties. Understanding phase transformation mechanisms among polymorphs enables the design of structures and tuning of phases to tailor material properties. However, current understanding is limited due to the lack of direct observations that track the processes and the structural evolution is not known at atomic scale. Here, integrating (semi) in situ transmission electron microscopy and density functional theory, we report atomic structural evolutions of phase transformation from anatase (A) to rutile (R), brookite (B), R-phase, and TiO. Besides the consistent paths with previous reports, we discover several unreported paths, including a [001] direction and (020) plane of anatase to [100]A and (011)R of rutile, respectively, ( , ) and , . Density functional theory analysis elucidates atomic structural evolution during the processes and over 16% of Ti-O bonds break and reform during the processes with energy barriers of ~0.7-1.0 eV per TiO2 formula unit. Under electron-beam irradiation, anatase particles transform into TiO2-R phase or TiO at high or room temperature, respectively. We also reveal the anisotropic nature of electron-beam effect, which is seldom discussed: dependence of crystallographic orientation with respect to electron-beam irradiation direction. Understanding the atomic structural evolution sheds light on interpreting and controlling TiO2 polymorphs and interface structures for various applications. The revealed electron-beam effects in our work provide guidance for in situ transmission electron microscopy studies.

Song, Miao↗

The noise from supersonic elliptic jets

This paper presents calculations of the noise radiated by a supersonic elliptic jet. The large scale structures in the jet, that are the predominant source of noise in the downstream direction, are modeled as instability waves. The evolution of the instability waves is determined by a local, linear, inviscid analysis. An expression is derived for the acoustic field outside the jet and the far field directivity associated with each instability wave. Calculations are performed for a Mach 1.5 elliptic jet with aspect ratio 2:1 and a Mach 2.0 elliptic jet with aspect ratio 2:1 and a Mach 2.0 elliptic jet with aspect ratio 3:1. The mean flow development is taken from experimental results. Comparisons are made with far field acoustic measurements.

Morris, Philip J.↗

DeepClone: Lightweight State Replication of Deep Learning Models for Data Parallel Training

Training modern deep neural network (DNN) models involves complex workflows triggered by model exploration, sensitivity analysis, explainability, etc. A key primitive in this context is the ability to clone a model training instance, i.e. “fork” the training process in a potentially different direction, which enables comparisons of different evolution paths using variations of training data and model parameters. However, in a quest improve the training throughput, a mix of data parallel, model parallel, pipeline parallel and layer-wise parallel approaches are making the problem of cloning highly complex. In this paper, we explore the problem of efficient cloning under such circumstances. To this end, we leverage several properties of data-parallel training and layer-wise parallelism to design DeepClone, a cloning approach based on augmenting the execution graph to gain direct access to tensors, which are then sharded and reconstructed asynchronously in order to minimize runtime overhead, standby duration, readiness duration. Compared with state-of-art approaches, DeepClone shows orders of magnitude improvement for several classes of DNN models.

data-parallel training↗

Effects of ion two-stream instability on auroral ion heating

The ion two-stream instability develops between upflowing H(+) and O(+) in the auroral acceleration region, if the two species are accelerated to different velocities in a semistationary electrostatic potential. Parallel propagating modes are unstable only for small relative drifts, while oblique modes remain unstable at larger drifts and, consequently, higher altitudes. The effects of oblique modes on ion heating are investigated, and it is found that O(+) heats primarily by trapping in the direction of wave propagation during the early, coherent phase of wave growth in the temporal evolution problem. After undergoing trapping along the magnetic field direction, H(+) heats primarily by quasi-linear diffusion when the spectrum broadens nonlinearly. The parallel ion distributions evolve by formation of a high-energy (low-energy) tail on oxygen (hydrogen) along with bulk slowing of hydrogen, which results in more energetic oxygen than hydrogen. Total heating is greatest in the direction of wave propagation, and this effect is greater for hydrogen than for oxygen.

Roth, I.↗

A modified Rietveld method to model highly anisotropic ceramics

High energy X-ray diffraction was employed to probe the complex constitutive behavior of a polycrystalline ferroelectric material in various sample orientations. Pb(Zn,Nb)O3-Pb(Zr,Ti)O3 (PZN-PZT) ceramics were subjected to a cyclic bipolar electric field while diffraction patterns were taken. Using transmission geometry and a two-dimensional detector, lattice strain and texture evolution (domain switching) were measured in multiple sample directions simultaneously. In addition, texture analysis suggests that non-180{sup o} domain switching is coupled with lattice strain evolution during uniaxial electrical loading. As a result of this material's high strain anisotropy, the full-pattern Rietveld method was inadequate to analyze the diffraction data. Instead, a modified Rietveld method, which includes an elastic anisotropy term, yielded significant improvements in the data analysis results.

36 MATERIALS SCIENCE↗

Temporal evolution of pore geometry, fluid flow, and solute transport resulting from colloid deposition

Deposition of colloidal particles is one of many processes that lead to the evolution of the structure of natural porous media in groundwater aquifers, oil reservoirs, and sediment beds. Understanding of the mechanisms and effects of this type of structural evolution has been limited by a lack of direct observations of pore structure. Here, synchrotron X-ray difference microtomography (XDMT) was used to resolve the temporal evolution of pore structure and the distribution of colloidal deposits within a granular porous medium. Column filtration experiments were performed to observe the deposition of relatively high concentrations of colloidal zirconia (200 mg/l of particles having diameter {approx}1 {micro}m) in a packed bed of glass beads (diameters 210-300 {micro}m). Noninvasive XDMT imaging of the pore structure was performed three separate times during each column experiment. The structural information observed at each time was used to define internal boundary conditions for three-dimensional lattice Boltzmann (LB) simulations that show how the evolving pore structure affects pore fluid flow and solute transport. While the total deposit mass increased continuously over time, colloid deposition was observed to be highly heterogeneous and local colloid detachment was observed at some locations in a low ionic strength medium. LB simulations indicated that particle accumulation greatly reduced the permeability of the porous medium while increasing the tortuosity. The colloidal deposits also increased the spatial variability in pore water velocities, leading to higher dispersion coefficients. Anomalous dispersion behavior was investigated by simulation at the scale of the experimental system: weak tailing was found in the clean bed case, and the extent of tailing greatly increased following colloid deposition because of the development of extensive no-flow regions. As a result of this coupling between pore fluid flow, colloid accumulation, and the pore geometry, colloid deposition is expected to strongly influence long-term solute dynamics in cases where solute transport is either accompanied by high colloid influx or where the passage of the solute front mobilizes and then redistributes material from the porous matrix.

54 ENVIRONMENTAL SCIENCES↗

Landau electron in a rotating environment: A general factorization of time evolution

For the Landau problem with a rotating magnetic field and a confining potential in the (changing) direction of the field, we derive a general factorization of the time evolution operator that includes the adiabatic factorization as a special case. The confining potential is assumed to be of a general form and it can correspond to nonlinear Heisenberg equations of motion. The rotation operator associated with the solid angle Berry phase is used to transform the problem to a rotating reference frame. In the rotating reference frame, we derive a natural factorization of the time evolution operator by recognizing the crucial role played by a gauge transformation. The major complexity of the problem arises from the coupling between motion in the direction of the magnetic field and motion perpendicular to the field. In the factorization, this complexity is consolidated into a single operator which approaches the identity operator when the potential confines the particle sufficiently close to a rotating plane perpendicular to the magnetic field. The structure of this operator is clarified by deriving an expression for its generating Hamiltonian. The adiabatic limit and non-adiabatic effects follow as consequences of the general factorization which are clarified using the magnetic translation concept.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗