Search NASA⌕ Search

SEARCH · Search NASA

Results for “Flexural testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Design of a thrust stand for high power electric propulsion devices

A thrust stand for use with high power electric propulsion devices has been designed and tested. The thrust stand was specifically tailored to the needs of a 0.1 to 0.25 MW magnetoplasmadynamic (MPD) thruster program currently in progress at the NASA Lewis Research Center. The thrust stand structure was built as an inverted pendulum arrangement, supported at the base by water-cooled electrical power flexures. Thrust stand tares due to thruster discharge current were demonstrated to be negligible. Tares due to an applied field magnet current, after considerable effort, were reduced to less than 3.0 percent of measured thrust. These tares, however, could be determined independently and subtracted from the indicated thrust measurement. The paper gives a detailed description of the thrust stand design and operation with a 0.1 MW class MPD device. Other thrust stand tares due to vibration and thermal effects are discussed, along with issues of accuracy and repeatability.

Haag, Thomas W.↗

Design of a thrust stand for high power electric propulsion devices

A thrust stand for use with high power electric propulsion devices was designed and tested. The thrust stand was specifically tailored to the needs of a 100 to 250 kW magnetoplasmadynamic (MPD) thruster program currently in progress at the NASA Lewis Research Center. The thrust stand structure was built as an inverted pendulum arrangement, supported at the base by water-cooled electrical power flexures. Thrust stand tares due to thruster discharge current were demonstrated to be negligible. Tares due to an applied field magnet current, after considerable effort, were reduced to less than 3.0 percent of measured thrust. These tares, however, could be determined independently and subtracted from the indicated thrust measurement. A detailed description is given for the thrust stand design and operation with a 100 kW class MPD device. Other thrust stand tares due to vibration and thermal effects are discussed, along with issues of accuracy and repeatability.

Haag, Thomas W.↗

Supersonic hot jet ablative testing and analysis of boron nitride nanotube hybrid composites

Boron nitride nanotubes (BNNTs) are high-strength, high-modulus nanotubes with high thermal and oxidative stabilities. Two hybrid composites were prepared with satin weave carbon fiber (CF) and resole-type phenolic resin: one with surface layers of BNNTs and one with alternating interlayers of BNNTs. The samples were subjected to hot jet tests that simulate realistic high-pressure-temperature conditions to understand the behavior of BNNTs under high-pressure erosion. Adding BNNTs to CF/phenolic laminates enhanced the ablation resistance by reinforcing the char material and mitigated localized thermal damage. Hybrid laminates exhibited up to 14% lower weight loss, 55% increase in flexural modulus, higher thermal diffusivity, and improved char yield and microstructure compared to CF/phenolic samples. The surface layer hybrid had many surviving nanotubes reinforcing the char and crystalline oxide structures that could mitigate further oxygen diffusion. Further, various characterization methods were used to deduce possible mechanisms and their products, indicating that BNNTs could serve as growth templates for direct crystalline boron oxide formation. Overall, hybrid BNNT/CF/phenolic laminates displayed better ablation resistance and favorable microstructure evolution under high-pressure conditions.

42 ENGINEERING↗

Thrust stand for vertically oriented electric propulsion performance evaluation

A variation of a hanging pendulum thrust stand capable of measuring the performance of an electric thruster operating in the vertical orientation is presented. The vertical orientation of the thruster dictates that the thruster must be horizontally offset from the pendulum pivot arm, necessitating the use of a counterweight system to provide a neutrally stable system. Motion of the pendulum arm is transferred through a balance mechanism to a secondary arm on which deflection is measured. A noncontact light-based transducer is used to measure displacement of the secondary beam. The members experience very little friction, rotating on twisting torsional pivots with oscillatory motion attenuated by a passive, eddy-current damper. Displacement is calibrated using an in situ thrust calibration system. Thermal management and self-leveling systems are incorporated to mitigate thermal and mechanical drifts. Gravitational force and torsional spring constants associated with flexure pivots provide restoring moments. An analysis of the design indicates that the thrust measurement range spans roughly four decades, with the stand capable of measuring thrust up to 12 N for a 200 kg thruster and up to approximately 800 mN for a 10 kg thruster. Data obtained from calibration tests performed using a 26.8 lbm simulated thruster indicated a resolution of 1 mN on 100 mN level thrusts, while those tests conducted on a 200 lbm thruster yielded a resolution of roughly 2.5 mN at thrust levels of 0.5 N and greater.

42 ENGINEERING↗

Development and mechanical properties of structural materials from lunar simulant

Development of versatile engineering materials from locally available materials in space is an important step toward establishment of outposts such as on the moon and Mars. Here development of the technologies for manufacture of structural and construction materials on the moon, utilizing local lunar soil (regolith), without the use of water, is an important element for habitats and explorations in space. It is also vital that the mechanical behavior such as strength and flexural properties, fracture toughness, ductility, and deformation characteristics are defined toward establishment of the ranges of engineering applications of the materials developed. The objectives include two areas: (1) thermal liquefaction of lunar simulant (at about 1100 C) with different additives (fibers, powders, etc.); and (2) development and use of a traxial test device in which lunar simulants are first compacted under cycles of loading, and then tested with different vacuums and initial confining or insitu stress. The second area was described in previous progress reports and publications; since the presently available device allows vacuum levels up to only 10(exp -4) torr, it is recommended that a vacuum pump that can allow higher levels of vacuum is acquired.

Desai, Chandra S.↗

Thrust Stand for Vertically Oriented Electric Propulsion Performance Evaluation

A variation of a hanging pendulum thrust stand capable of measuring the performance of an electric thruster operating in the vertical orientation is presented. The vertical orientation of the thruster dictates that the thruster must be horizontally offset from the pendulum pivot arm, necessitating the use of a counterweight system to provide a neutrally-stable system. Motion of the pendulum arm is transferred through a balance mechanism to a secondary arm on which deflection is measured. A non-contact light-based transducer is used to measure displacement of the secondary beam. The members experience very little friction, rotating on twisting torsional pivots with oscillatory motion attenuated by a passive, eddy current damper. Displacement is calibrated using an in situ thrust calibration system. Thermal management and self-leveling systems are incorporated to mitigate thermal and mechanical drifts. Gravitational restoring force and torsional spring constants associated with flexure pivots provide restoring moments. An analysis of the design indicates that the thrust measurement range spans roughly four decades, with the stand capable of measuring thrust up to 12 N for a 200 kg thruster and up to approximately 800 mN for a 10 kg thruster. Data obtained from calibration tests performed using a 26.8 lbm simulated thruster indicated a resolution of 1 mN on 100 mN-level thrusts, while those tests conducted on 200 lbm thruster yielded a resolution of roughly 2.5 micro at thrust levels of 0.5 N and greater.

Moeller, Trevor↗

Development of a composite geodetic structure for space construction, phase 2

Primary physical and mechanical properties were defined for pultruded hybrid HMS/E-glass P1700 rod material used for the fabrication of geodetic beams. Key properties established were used in the analysis, design, fabrication, instrumentation, and testing of a geodetic parameter cylinder and a lattice cone closeout joined to a short cylindrical geodetic beam segment. Requirements of structural techniques were accomplished. Analytical procedures were refined and extended to include the effect of rod dimensions for the helical and longitudinal members on local buckling, and the effect of different flexural and extensional moduli on general instability buckling.

Source record↗

Guidance accuracy considerations for realtime GPS interferometry

During April and May of 1991, the Avionics Engineering Center at Ohio University completed the first set of realtime flight tests of a GPS interferometric attitude and heading determination system. This technique has myriad applications for aircraft and spacecraft guidance and control. However, before these applications can be further developed, a number of guidance accuracy issues must be considered. Among these are: signal derogation due to multipath and shadowing, effects of structural flexures, and system robustness during loss of phase lock. This paper addresses these issues with special emphasis on the information content of the GPS signal, and characterization and mitigation of multipath encountered while in flight.

Braasch, Michael S.↗

MXene Reinforced Thermosetting Composite for Lightning Strike Protection of Carbon Fiber Reinforced Polymer

Ti 3 C 2 – a member of the MXenes (2D transition metal carbides and nitrides) family, is investigated as an effective filler to improve the electrical, mechanical, and thermal properties of divinylbenzene (DVB) thermosetting resin. Consequently, its performance as a lightning strike protection (LSP) coating for carbon fiber reinforced polymer (CFRP) is evaluated. Polyaniline (PANI) – dodecylbenzene sulfonic acid (DBSA) complex is used to cure the DVB resin. The synergic effect of MXenes (with surface that is negatively charged) with polyaniline (positive charge) shows electrostatic bonding and improved electrical conductivity in the composite. We also find that the addition of MXenes at 2 wt% into the PANI-DVB composite shows ≈139%, 10%, and 9% improvement in electrical conductivity, flexural strength, and flexural modulus, respectively, compared to the neat PANI-DVB composite. The composites are investigated using various material characterization techniques including Fourier transforms infrared spectroscopy, thermogravimetric analysis, differential scanning calorimetry, and scanning electron microscopy. Furthermore, MXenes-DVB is utilized to create a conductive thermosetting coating on top of a CFRP substrate and tested against a lightning strike of 100 kA. CFRP with MXenes-DVB coating reduced the surface damage from 40.61 cm 2 (reference CFRP panel) to 13.29 cm 2 (CFRP coated with MXenes-DVB).

36 MATERIALS SCIENCE↗

Performance of an electromagnetic bearing for the vibration control of a supercritical shaft

The flexural vibrations of a rotating shaft, running through one or more critical speeds, can be reduced to an acceptably low level by applying suitable control forces at an intermediate span position. If electromagnets are used to produce the control forces then it is possible to implement a wide variety of control strategies. A test rig is described which includes a microprocessor-based controller, in which such strategies can be realised in terms of software-based algorithms. The electromagnet configuration and the method of stabilising the electromagnet force-gap characteristic are discussed. The bounds on the performance of the system are defined. A simple control algorithm is outlined, where the control forces are proportional to the measured displacement and velocity at a single point on the shaft span; in this case the electromagnet behaves in a similar manner to that of a parallel combination of a linear spring and damper. Experimental and predicted performance of the system are compared, for this type of control, where various programmable rates of damping are applied.

Bradfield, C. D.↗

Nicalon/siliconoxycarbide ceramic composites

A series of silsesquioxane copolymers was synthesized by acid hydrolysis and condensation of trimethoxysilanes of the form RSi(OCH3)3, where R = methyl or phenyl. By varying pH, water/methoxy and methyl/phenyl ratios, the molecular structure, polymer rheology and ceramic composition can be controlled. The polymers form an amorphous siliconoxycarbide on pyrolysis. Composites of Nicalon/siliconoxycarbide were fractured in four-point flexure and in tension to evaluate the influence of matrix composition, final fabrication temperature and use of filler on composite mode of failure, modulus, strain capability and strength. Incorporation of filler was found to increase matrix compressive strength. Employment of processing temperatures of 1375 to 1400 C enhanced strain to failure and reduced the tendency toward brittle fracture. Mixed mode (compression/shear and tension/shear) failures were observed in flexural samples processed to the higher temperatures, giving rise to nonlinear stress-strain curves. Tensile samples pyrolyzed to 1400 C showed linear-elastic behavior and failed by fracture of fiber bundles. Matrix material was found to be adherent to the fiber surface after failure. These results demonstrate the need for tensile testing to establish composite behavior.

Hurwitz, Frances I.↗

Response to reflected-force feedback to fingers in teleoperations

Reflected-force feedback is an important aspect of teleoperations. The objective is to determine the ability of the human operator to respond to that force. Telerobotics operation is simulated by computer control of a motor-driven device with capabilities for programmable force feedback and force measurement. A computer-controlled motor drive is developed that provides forces against the fingers as well as (angular) position control. A load cell moves in a circular arc as it is pushed by a finger and measures reaction forces on the finger. The force exerted by the finger on the load cell and the angular position are digitized and recorded as a function of time by the computer. Flexure forces of the index, long and ring fingers of the human hand in opposition to the motor driven load cell are investigated. Results of the following experiments are presented: (1) Exertion of maximum finger force as a function of angle; (2) Exertion of target finger force against a computer controlled force; and (3) Test of the ability to move to a target force against a force that is a function of position. Averaged over ten individuals, the maximum force that could be exerted by the index or long finger is about 50 Newtons, while that of the ring finger is about 40 Newtons. From the tests of the ability of a subject to exert a target force, it was concluded that reflected-force feedback can be achieved with the direct kinesthetic perception of force without the use of tactile or visual clues.

Sutter, P. H.↗

DROP DURABILITY ASSESSMENT OF ELECTRONIC ASSEMBLIES UNDER OFF-AXIS LOADING WITH SKEWED FIXTURES

This thesis studies drop durability of electronic assemblies when the acceleration vector is oriented at 45° to the out-of-plane direction of the circuit card. The off-axis drop tests are accomplished with a skewed fixture and are conducted as a proxy for multiaxial drop testing. Advanced shock testing and vibration test methods have been developed over the last few decades to better represent real-world field environments during ground-based laboratory testing. However, many of these test methods require expensive and specialized equipment not available in most laboratories. An alternative approach for approximating simultaneous loading along multiple axes on conventional equipment utilizes skewed fixtures which have seen use in off-axis random vibration and drop impact testing. These methods generally rely on the conversion of a uniaxial input load from the test equipment (using a uniaxial drop tower or shaker) into a multiaxial load when resolved in the reference frame of the test article (mounted on a skewed fixture). Skewed fixture design is presented and recommendations for conducting skewed angle drop testing are introduced based on local measurements along the skewed face of the fixture to accurately monitor the impact event. Characterization tests were performed with a skewed fixture, at simultaneous acceleration loads from 500 to 3,000 g in two (in-plane and out-of-plane) directions, while meeting standard time domain tolerances. Upon experimental characterization, drop shock durability tests were conducted on a printed circuit assembly (PCA). Mean drops-to-failure were measured and quantified with Weibull statistics. Dominant solder joint failure modes were identified via failure analysis. Prior work on inclined angle impact testing is limited, and the majority of solder joint interconnect level fatigue studies are conducted considering perpendicular loading normal the circuit card. Low-cycle fatigue curves are generated based on plastic strain and plastic work density within the solder joint. A multiscale nonlinear finite element model is used to relate board-level flexure to solder joint interconnect level plastic strain. A high strain rate solder constitutive model allows for accurate modeling of solder plasticity resulting from high-impact drop shock. Fatigue parameters are computed from the Coffin-Manson relation and Palmgren-Miner damage accumulation. This work serves to apply established low-cycle fatigue methods for conventional drop shock loading (impact normal to circuit card) to non-perpendicular loading with a skewed fixture.

Hower, Jonathan [Kansas City National Security Cam↗

Optical matching for fiber optic spectroscopy

Single silica fibers of the type developed for communications are useful in the design of astronomical spectrographs. They can be used to couple light from many objects over a wide field to a single spectrograph, or to eliminate wavelength errors from image motion and gravitational flexure. For many applications it will be advantageous to use small lenses to make the most efficient coupling into and out of a fiber. If the telescope pupil is imaged on the fiber core, an efficient coupling can be made that preserves image size over a certain range. This method is demonstrated by a laboratory test using sapphire spheres as coupling lenses.

Hill, J. M.↗

The effect of low velocity impact on the strength characteristics of composite materials laminates

The nonlinear and dynamic response of composite structures to impact loading conditions was investigated. The convergence of both finite element and finite difference solution procedures was investigated with this configuration. The response of composite beams and plates to impact were examined. Fundamental data on the indentation and flexural response of both plate and beam geometry were collected. Numerical analyses were extended to the study of circular plates subjected to impact loading. Further work was done in modeling the response to simulated impact loading through careful modeling of the momentum transfer from impactor to target. The modeling methodology and solution procedures were well tested and verified. A computer program for the solution of circular plate problems was developed and is under testing.

Liebowitz, H.↗

Design and Development of a Robust Chuck Mechanism for the Mars2020 Coring Drill

The Sampling and Caching Subsystem (SCS) onboard the Mars2020 rover includes a coring drill that can perform coring, abrasion, and regolith collection operations. The coring drill requires a chuck mechanism to allow for the changing of the bits needed to perform sampling. The chuck mechanism must be capable of securely connecting a bit under drilling, rover slip, and pullout loads, but also readily release a bit after application of these loads. The Mars2020 chuck consists of a ball lock mechanism that allows for robust engagement and release of bit assemblies that is preloaded to ensure a secure, stiff connection between the bit assembly and the rest of the corer. To prevent jamming, the chuck incorporates rollers to preload the ball lock. The rollers are mounted onto a flexured cam that minimizes changes in internal mechanism loads that result from thermally induced dimensional changes, further mitigating the potential for jamming. The chuck mechanism is moved between engaged, disengaged, and loose chuck positions by rotating the cam with a gearmotor that incorporates a magnetic detent brake that prevents inadvertent mechanism motion under design loads. Ongoing testing is occurring on the qualification model in a dirty environment while coring and abrading rocks in a Mars representative environment.

Barletta, Anthony↗

Detrital U-Pb zircon and 40 Ar/ 39 Ar muscovite geochronology from Middle Pennsylvanian strata in the Anadarko Basin, Texas Panhandle, USA

The Late Mississippian-Permian Anadarko Basin formed in Texas and Oklahoma, USA as the result of inversion of Neoproterozic and Cambrian rift structures. Subsidence was driven by flexural loading of the Amarillo-Wichita Uplift, and this uplift may represent the easternmost element of the Ancestral Rocky Mountains system. The northwestern part of this basin has generally been interpreted to have been filled by sediment derived from the Ancestral Front Range Uplift, ~475 km to the northwest during the early stages of basin filling. We test this model using U-Pb detrital zircon and 40 Ar/ 39 Ar detrital muscovite results from three subsurface samples of the Morrow B sandstone in the northwestern part of the Anadarko Basin. We provide a new maximum depositional age of 310.9 ± 4.9 Ma that indicates the age of the Morrow B to be no older than late Atokan to early Desmoinesian Age (Moscovian), ~10 Myr younger than previously interpreted. In contrast to some previous interpretations, we propose that the most likely source for the sediment in the Morrow B is the Amarillo Uplift to the south. Detrital zircon and detrital muscovite data have age peaks at 900–1300 Ma, 1370 Ma and 1600–1800 Ma corresponding to derivation from Grenville, Granite-Rhyolite and Yavapai-Mazatzal basement provinces, respectively. A dominant detrital zircon peak at 1370 Ma suggests that Mesoproterozoic granites in the Amarillo Uplift were exposed by Middle Pennsylvanian time, and detritus eroded from the Amarillo Uplift dominated the lowstand sediment budget of the Texas Panhandle during this time; small volumes of sediment were likely sourced from the Ancestral Front Range. In conclusion, this study presents the first detrital geochronology data from the subsurface Anadarko Basin and the first detrital muscovite data from late Paleozoic southwestern Laurentia. The results presented here highlight the interpretive power of combined detrital zircon and muscovite datasets.

58 GEOSCIENCES↗

Reliability improvement of 1 mil aluminum wire bonds for semiconductors, technical performance summary

The reliability of semiconductor devices as influenced by the reliability of wire bonds used in the assembly of the devices is investigated. The specific type of failure dealt with involves fracture of wire bonds as a result of repeated flexure of the wire at the heel of the bond when the devices are operated in an on-off mode. The mechanism of failure is one of induced fracture of the wire. To improve the reliability of a chosen transistor, one-mil diameter wires of aluminum with various alloy additions were studied using an accelerated fatigue testing machine. In addition, the electroprobe was used to study the metallurgy of the wires as to microstructure and kinetics of the growth of insoluble phases. Thermocompression and ultrasonic bonding techniques were also investigated.

Source record↗