Search NASA⌕ Search

SEARCH · Search NASA

Results for “Gas processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Performance and flexibility improvements of Staged Pressurized Oxy-Combustion

Staged Pressurized Oxy-Combustion (SPOC) is a low-carbon coal combustion power technology being developed by Washington University in St. Louis (WUSTL). Oxy-combustion plants enable straightforward capture of carbon dioxide (CO 2 ) by removing most of the nitrogen in the combustion air prior to use, thereby burning fuel in near-pure oxygen instead of air, producing a flue gas containing primarily CO 2 and water. CO 2 capture at amounts > 90% is possible, often using cryogenic air separation. Oxy-combustion typically relies on flue gas recycle (FGR) to reduce the peak temperature and radiation that would otherwise occur in a fuel/oxygen only flame. SPOC reduces the peak temperatures of combustion by utilizing two or more pressurized boiler modules connected in series to produce fuel staging; hence, only a portion of the fuel is combusted in any given furnace module. This means that the thermal energy released at each stage can be captured and removed from the gases prior to subsequent stages, when more fuel is introduced. This allows the SPOC process to operate with minimal FGR, avoiding the associated efficiency losses and additional costs. Also, the process operates at an elevated gas-side pressure, reducing boiler size, enhancing heat transfer to achieve a compact boiler configuration as compared to an atmospheric-pressure boiler design, and allowing for recovery of the latent heat of the water from the flue gas at a temperature useful to the steam cycle. The resultant net efficiency of the system is over 3 percentage points greater than traditional atmospheric-pressure oxy-combustion, and 7 percentage points greater than the post combustion variant, representing a step-change improvement over first-generation capture technologies. To further develop the concept, WUSTL and the Electric Power Research Institute, Inc., organized a project with American Air Liquide, Inc., Doosan Babcock Limited, and the U.S. Department of Energy to investigate a practicable and workable boiler design. The team has identified the potential for enhanced process flexibility for controlling power generation over a wider load range than is normally available to conventional coal-fired power plants due to the staged nature of the heat release. With increasing intermittent renewable generator contribution, on-demand generators need to be highly flexible to participate in the future energy market, requiring extensive operation at reduced load. Conventional coal-fired steam generators typically face challenges in maintaining temperature control of the reheat steam and main steam at reduced loads. This results in inefficient operation, both in terms of the boiler efficiency and steam turbine heat rate. The results of this project show the SPOC process is capable of exceptional turndown, both on a stage basis and with the ability to bypass entire stages. Oxygen-supply flexibility was also investigated, as this is also a key consideration for the overall flexibility of the SPOC process given the operating constraints of conventional air separation units. A boiler design concept assessment was conducted and was focused on delivering compact and constructible design. The assessment checked appropriate tube operating metal temperatures at full load and at lower operating loads, balanced against the needs of efficient coal combustion, and the resultant slagging and ash environments. Combustion testing in the 100-kWth pressurized combustion test rig at WUSTL was carried out to validate the combustion, heat flux profiles and burnout at multiple loads. Combustion parameters investigated were flame stability, fuel burnout, ash composition, radiative heat flux, and temperature profiles. The results of these tests formed the basis of a full-scale boiler design that will encompass improvements in both efficiency and flexibility over conventional oxy-combustion processes. The air separation unit flexibility was investigated, and associated cost implications were addressed. Detailed economic assessment results for a 550 MWe net power block are also provided, allowing for a comparison against the baseline NETL oxy-combustion and post combustion capture cases.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2023

Scale-up Testing of Advanced Polaris Membrane in CO2 Capture Technology

This final technical report describes work conducted by Membrane Technology and Research, Inc. (MTR) for the U.S. Department of Energy (DOE), National Energy Technology Lab (NETL) on the scale-up and testing of advanced Polaris™ membrane CO2 capture technology at the Technology Centre Mongstad (TCM) under award number DE-FE0031591. The work was performed from August 1, 2018 through January 31, 2023. The overall goal of this project was to design, build and operate an advanced Polaris membrane CO2 capture system at TCM. MTR was assisted in this project by Trimeric Corporation (Trimeric), an engineering design services company, the Carbon Capture Simulation for Industry Impact (CCSI2), a partnership among national laboratories, industry, and academic institutions, and the Technology Centre Mongstad (TCM), who provided the host site for the slipstream field test. This report details the work conducted to scale-up MTR’s second-generation (Gen-2) Polaris membrane and advanced planar membrane modules to a final form factor optimized for commercial use; validate their performance in an engineering-scale field test at TCM; and to show the potential of the MTR process to meet DOE CO2 capture targets from large source point emitters. Work for this project included membrane optimization and scale-up, advanced planar module design and fabrication, design and fabrication of an engineering-scale field test membrane skid, operation of the field test skid processing Residue Fluid Catalytic Cracker (RFCC) industrial flue gas at TCM, and a detailed techno-economic analysis (TEA) of the MTR membrane post-combustion process for CO2 capture. This project validated recent membrane technology advancements at the engineering-scale, moves the MTR advanced post-combustion capture technology to TRL-6, and mitigates risk in future Large Pilot or Demonstration scale-up activities.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2023

Framework for Greenhouse Gas Emissions Reduction Planning: Industrial Portfolios

The Framework for Greenhouse Gas Emissions Reduction Planning: Industrial Portfolios articulates a process to help industrial organizations develop a specific, actionable plan to achieve Scope 1 and Scope 2 greenhouse gas (GHG) emissions reduction – an Emissions Reduction Plan (ERP). An ERP covers an entire portfolio of facilities, yet contains enough detail to be practically useful at the facility level.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2022

System and method for remote detection and location of gas leaks

A system for monitoring for a gas leak from a gas containing structure is disclosed. The system includes a lens that directs an image of a scene of interest through an optical filter onto a detector. The filter is associated with the lens and the filter has one or more passbands that passes wavelengths which match one or more emission or reflectively wavelengths of the gas being monitored. A detector receives the image after the image passes through the lens and the filter. The detector generates image data representing the scene including the gas containing structure. A processor is configured to process the image data by executing machine executable code stored on a memory. The machine executable code processes the image data to identify turbulence flows in the image data such that turbulence flow indicates a gas leak, and generate and send an alert in response to the identification of a turbulence flow.

O'Neill, Mary D.↗
DOE OSTI2024

NO formation by N 2 /O 2 plasma catalysis: The impact of surface reactions, gas-phase reactions, and mass transport

Pathways and timescales relevant to facilitate plasma-assisted N 2 -O 2 reactions are assessed by measuring the consumption of plasma-derived N and the formation of NO in the gas phase and over Ag catalytic surfaces. These measurements are enabled by a setup that enables N 2 activation in an atmospheric pressure RF plasma jet, enables O 2 addition in the plasma afterglow, facilitates reactions over an Ag wire catalyst, and allows species density quantification by molecular beam mass spectrometry. Gas-phase reactions consume N but do not form NO with high selectivity. The presence of the non-porous Ag wire catalyst increases the rate of N conversion to NO, though mass transfer processes, not surface reactions, dictate the rate of N consumption. When O 2 concentrations and the ratio of the surface area of the catalyst to the void volume of the reactor are high (3–5 mol% O 2 , 10900 m –1 ), N conversion to NO reaches 100 % selectivity. When both N 2 and O 2 are fed through the plasma jet, gas-phase NO production increases 10×, although plasma and gas-phase processes do not exclusively produce NO. Above a threshold NO density, N cannot diffuse to the catalyst surface faster than it is consumed in the gas phase by reactions with NO. Furthermore, the use of heterogeneous catalysts to enhance plasma-driven N x O y formation and control N x O y product selectivity is limited to cases where diffusive transport of N from the gas phase to the catalyst surface is faster than consumption of N from gas-phase reactions with NO.

Engineering↗
DOE OSTI2025

Implications of point defect accumulation on UO 2 thermal conductivity and fission gas release under accelerated fuel irradiation

Evaluation of thermal properties is a crucial factor for nuclear fuel performance. During reactor operation, the accumulation of fission products and irradiation-induced lattice defects are responsible for degradation in thermal conductivity. Consequently, it affects fuel temperature and fission gas release (FGR) among other Multiphysics processes important for economics and safety analysis. We analyze the implications of point defects (PD) accumulation described using a rate theory (RT) Model on lattice thermal conductivity of UO 2 . Here, we demonstrate that fission rate-dependent point defect concentrations have the largest impact on in-pile thermal conductivity in the periphery of light water reactor fuels below a temperature threshold governed by the migration barrier of defects. Our analysis provides a mechanistic description of this phenomena which current fuel performance codes treat empirically. The reduction of thermal conductivity in the low -temperature rim region acts as additional thermal resistance and leads to a temperature notably larger than suggested by Lucuta thermal conductivity correlation. These effects are anticipated to have notable impacts when fuels are exposed to accelerated radiation. The impact of such point defect-informed treatment of thermal conductivity on fuel performance is evaluated by a detailed analysis of fission gas behavior and its release. We consider several models capturing different stages of fission gas bubble evolution and fission gas release (FGR). Finally, a new fission rate-dependent correction to the Lucuta correlation is proposed. The results show a significant reduction in thermal conductivity at the fuels’ periphery and an increase in fuel centerline temperature specifically at low burnups. Ultimately a modified LC shows a higher FGR compared to the original LC, while the acceleration process results in a reduction in overall FGR.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Understanding extraction limits of plasma cathodes with experiment and simulation

The project is focused on computations for enhanced ionization near the exit orifice of a plasma cathode and how the cathode extraction electrode geometry and stray magnetic field structure influence available extractable current. The computational effort will take place at the Princeton Collaborative Research Laboratory (PCRF). The specific modeling platform to be utilized from PCRF is the electrostatic direct implicit particle in cell (EDIPIC) code. EDIPIC will be used to study ionization processes in the electron extraction region of the cathode. The control of electron energy is a key aspect to minimizing power losses in the plasma. Exiting electrons ionize gas leaving the orifice and in the process produce the dense plasma from which large amounts of current can be extracted. Project activities include studying processes that determine the energy distribution of the exiting electrons thus providing insight into how to optimize the source. The model will be validated and developed using experimental measurements as warranted. The familiarity and expertise of the team at PPPL with this type of plasma and the challenges posed greatly enhances the likelihood of gaining insight into the extraction sheath under the duration of the proposed activity. The effort is expected to shed a great deal of insight into electron extraction processes and pathways for optimization.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

How to Minimize Faradaic Efficiency Error in Electrochemical CO 2 Reduction for Gas Products

Faradaic efficiency (FE) is an important metric for evaluating electrochemical processes, such as carbon dioxide reduction, that is often used for performance comparisons. Although the equation to calculate FE is well-known, details needed to yield accurate values are often overlooked, potentially leading to errors exceeding 100%. Avoiding any errors is crucial for drawing correct conclusions, especially during a catalysis optimization process. Factors with high potential for FE errors include incorrect mass flow rates and temperature values, imprecise gas chromatography calibrations, and uncorrected gas viscosities, while factors with less potential are also identified. In conclusion, this manuscript presents FE calculation guidelines intended for both newcomers and experts in the field of electrochemical fuel production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Demonstrating Safeguards Applications of DRiFT Gas Detector Capabilities [Slides]

DRiFT, a Detector Response Function Toolkit, post-processes MCNP output to model detector response. Three primary components: scintillator (focus of FY 21 TED work), gas detectors (focus of this FY), and semiconductor detectors. Capability to model scintillator detectors has previously been demonstrated.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Circular Reprocessing of Thermoset Polyurethane Foams

Thermoset polyurethane (PU) foams are widely used in industrial applications, but they cannot be recycled by conventional melt reprocessing because of their cross-linked structures. The introduction of carbamate exchange catalysts converts thermoset PU into covalent adaptable networks (CANs), which are amenable to reprocessing at elevated temperatures. However, this approach has produced solid PU films, which have fewer uses and lower commercial demand. In this work, simultaneous reprocessing and refoaming of thermoset PU foams is demonstrated by leveraging the melt-processability of PU CANs and allowing cell growth by gas generation in a twin-screw extruder. The optimal operating temperature of the refoaming process is determined through chemical, thermal, and structural analysis of PU foam extrudates. The foam-to-foam extrusion process produces controllable, continuous, and uniform foam structures, as characterized by cell diameter and cell number density. Low-density PU foams are obtained through a process simulating injection molding. The compression properties of reprocessed PU foam are compared with as-synthesized PU foam to demonstrate efficacy of the refoaming processes. These results demonstrate that PU foams can be prepared through recycling while maintaining microstructural and chemical integrity. In the future, this strategy may be applied to thermoset PU foams of various chemical compositions and shows promise for scalability.

36 MATERIALS SCIENCE↗
DOE OSTI2021

AGR 5/6/7 Data Qualification Report for ATR Cycles 162B through 168A

This report provides the qualification status of experimental data for the Advanced Gas Reactor (AGR) 5/6/7 fuel irradiation. AGR-5/6/7 was conducted in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) in support of development and qualification of tri-structural isotropic (TRISO) low-enriched fuel for use in high temperature gas-cooled reactors. The objectives of the AGR-5/6/7 experiments are to: (i) irradiate reference-design fuel particles to support fuel qualification, (ii) establish operating margins for the fuel beyond normal operating conditions, and (iii) provide irradiated-fuel performance data and irradiated-fuel samples for post-irradiation examination (PIE) and safety testing. The test train contains five separate capsules that were independently controlled and monitored. Each capsule contains multiple 12.51-mm-long compacts filled with low enriched uranium carbide/oxide (UCO) TRISO fuel particles. The primary objective of the AGR-5/6 test (Capsules 1, 2, 4, and 5) is to verify successful performance of the reference-design fuel under normal operating conditions. The AGR-7 test (Capsule 3) was designed to explore fuel performance at higher temperatures to demonstrate the capability of the fuel to withstand conditions beyond normal operating conditions in support of plant design and licensing. AGR 5/6/7 will also provide irradiated-fuel performance data on fission-gas release from failed particles during irradiation. The AGR-5/6/7 capsules were irradiated in the ATR northeast flux trap location. The experiment began on February 16, 2018 and ended on July 22, 2020, spanning nine ATR cycles over two and a half years. Thus, the AGR-5/6/7 fuel compacts were irradiated for a total of 360.9 effective full power days. The AGR 5/6/7 experiment was able to remain in the reactor core during all three Powered Axial Locator Mechanism (PALM) cycles (163A, 165A, and 167A) without overheating its fuel compacts. This report includes irradiation monitoring data from nine ATR Cycles: 162B, 163A, 164A, 164B, 165A, 166A, 166B, 167A, and 168A, as stored in the Nuclear Data Management and Analysis System (NDMAS). During irradiation, data records consisted of instantaneous measurements recorded every minute and provided by text files automatically every 2 hours. The AGR 5/6/7 data streams addressed in this report include thermocouple (TC) temperatures, sweep gas data (flow rates [capsule inlet, outlet, and downstream at detector], pressure, and moisture content), and Fission Product Monitoring System (FPMS) data (release rates and release to birth rate ratios [R/Bs]) for each of the five capsules. A total of 94,989,908 TC temperature and sweep gas data records were received and processed by NDMAS for AGR 5/6/7 irradiation. Of these records, 41,593,387 (or 43.7% of the total) met data collection and accuracy requirements and are labeled as Qualified. A total of 57,746,693 TC temperature readings were captured from 54 installed TCs. Among them, 10,034,676 TC temperature records (only 17.4%) were Qualified and 47,701,371 TC temperatures (or 82.6%) are Failed due to 48 TC failures (63.5%) and due to missing values (19.1%). To assess performance of the operational TCs, analysis of daily correlations between TCs found no evidence of virtual junction failure for any TCs. Analyses on control charts of TC temperature differences revealed trending in TC readings for TC2, 4, 5, and 13 in Capsule 3, but there is no conclusive indication of TC drift failure that caused those trends. Therefore, TC control charts are not used to disqualify TC data, but only for users’ consideration. For sweep gas flow rates, a total of 31,519,747 gas flow records (84.4%) are Qualified for use for AGR-5/6/7 experiment; 5,723,468 gas flow records (15.4%) are Failed due mostly to missing values; and 74,641 high sweep gas flow rates (0.2 %) are Trend. A large number of Failed missing TC temperature and gas flow values were caused by an error in the data output script that outputted a ‘NULL’ value when values were unchanged. This problem was fixed during the outage of Cycle 166B, which led to a substantially decreased number of missing values during the last three cycles. Nonetheless, a large amount of non-missing data remained because of the high data acquisition frequency (1-minute) and still provided sufficient data to effectively monitor the experiment as designed. For FPMS data, NDMAS received and processed fission product release and R/B data for nine ATR cycles, when ATR core reached full power during AGR 5/6/7 irradiation. These data consist of 110,388 release rate records and 110,388 R/B records for the twelve radionuclides (Kr 85m, Kr 87, Kr 88, Kr 89, Kr 90, Xe 131m, Xe 133, Xe 135, Xe 135m, Xe 137, Xe 138, and Xe 139) for each of the five capsules. Equivalent numbers of uncertainty records associated the release rates and R/B values were provided. To date, qualification status of the FPMS data stored in the NDMAS dat

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Manufacturing Oxide Dispersion Strengthened (ODS) steel plate via cold spray and friction stir processing

Oxide dispersion strengthened (ODS) steels, traditionally fabricated by ball milling and conventional powder metallurgy techniques to achieve bulk form, followed by intricate rolling and thermal treatment steps to achieve plate or sheet form. Here, we present a novel processing route that combines cold spray (CS) with friction stir processing (FSP) to manufacture ODS steel plate directly from gas atomization reaction synthesis (GARS)-prepared powder, thus no rolling steps involved. Microstructural and mechanical characterizations were performed to assess the quality and properties of the resulting ODS steel plate. Our findings demonstrate that the slightly porous CS deposited layer was fully consolidated after FSP, yielding a fully dense ODS steel plate that exhibited a favorable tradeoff between strength and ductility upon extraction from the substrate. Furthermore, through microstructural analysis, we revealed the presence of an appreciable density (∼10 22 /m 3 ) of nano-sized oxide particles, with the majority being smaller than 5 nm via the combined CS + FSP fabrication route. This work serves as a first proof-of-concept demonstration of the manufacturing approach described herein, offering a possible alternative route for producing ODS steel plates.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Laboratory-Scale Melter Systems for Simulated and Real AP-107 Tank Waste - 20483

The Hanford Waste Treatment and Immobilization Plant (WTP) will process and stabilize waste that is stored in underground tanks on the Hanford Site. At the WTP, the tank waste will be combined with glass-forming and modifying additives to form an aqueous and solid mixture called melter feed, which will then be vitrified in joule-heated melters. A small-scale melter system, the continuous laboratory-scale melter (CLSM), is designed to operate with a continuous feeding process while periodically pouring glass product and collecting off-gas. Two CLSMs were constructed: one in a non-radioactive environment for processing waste simulants and another in a fume hood capable of handling radioactive material for processing actual Hanford tank waste. The waste sample received for vitrification in the CLSM was from Hanford tank 241-AP-107. Approximately 12 liters of melter-feed slurry was vitrified into 7 kilograms of glass product over the course of 10 hours of charging to the CLSM. The partitioning of technetium-99 in the product streams was used to calculate the technetium-99 recovery and help determine when the vitrification process had reached a steady state. The average single-pass retention of technetium-99 in the glass product was then calculated for the processing of AP-107 waste in the CLSM system. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Microbial Ecology of Permafrost Soils: Populations, Processes, and Perspectives

Permafrost microbial research has flourished in the past decades, due in part to improvements in sampling and molecular techniques, but also the increased focus on the permafrost greenhouse gas feedback to climate change and other ecological processes in high latitude and alpine permafrost soils. Permafrost microorganisms are adapted to these extreme environments and remain active at low temperatures and when resources are limited. They are also an important component of global elemental cycles as they regulate organic matter turnover and greenhouse gas production, particularly as permafrost thaws. Here we review the permafrost microbiology literature coupled with an exploration of its historical aspects, with a particular focus on a new understanding advanced by molecular biology techniques. We further identify knowledge gaps and ways forward to improve our understanding of microbial contributions to ecosystem biogeochemistry of permafrost-affected systems.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Effect of 316 stainless steel powder processing conditions on microstructure

One parameter that has both economic and performance effects in the manufacturing of steel parts is the powder feedstock used. 316 L steel powder can be produced through water atomization or gas atomization, where both the powder size and the atomization process determine the cost of powder feedstock. Gas atomized powder is spherical and has a lower oxygen content than water atomized powder, making it the preferred choice for performance, but comes at a higher financial cost. Here, in this study, various 316 L powder batches are characterized to understand physical properties and microstructural variations. Density and flowability were determined using gas pycnometry and Hall flow tests. Powder morphology and porosity were qualitatively analyzed via optical microscopy and scanning electron microscopy, Finally, transmission electron microscopy was used to determine changes in phases present. Spherical gas atomized powder of 30–100 μm contained Mn$-$Si rich oxides both on the surface and within the matrix. Meanwhile, irregular water atomized powder 30 μm in diameter contained silicon oxides without manganese. All powder particles contained a nickel rich cellular structure which was shown to support the formation of additional phases. While literature has observed general microstructural features across 316 L powder particles, transmission electron microscopy (TEM) in this study has identified variations in precipitation and cell structures. Information regarding morphology, flowability, density, and phase distributions can be applied to understand variations in part consolidation, which will in turn show which powder aspects are significant for production.

Chemical segregation↗
DOE OSTI2020

Direct functionalization of C-H bonds by electrophilic anions

Bond formation between two of the most inert molecules, alkanes and [B12X12]2- (X = Cl, Br), is performed in a two step process. Fragmentation of [B12X12]2- in the gas phase generates highly reactive [B12X11]- ions which spontaneously react with alkanes. The reaction mechanism was investigated using tandem mass spectrometry and gas-phase vibrational spectroscopy combined with electronic structure calculations. This effort revealed the unprecedented and counterintuitive electrophilic substitution of a proton in an alkane by a negatively charged ion resulting in a B-C bond formation. The product is a dianionic [B12X11CnH2n+1]2- species, in which H+ is electrostatically bound to the dianion. High flux ion soft-landing was performed to co-deposit [B12X11]- and complex organic molecules (phthalates) in thin layers on surfaces. Molecular structure analysis of the product films revealed that C-H functionalization by [B12X11]- occured in the presence of other more reactive functional groups. This observation demonstrates the utility of highly reactive fragment ions for defined bond formation processes and may pave the way to the use of gas phase ion chemistry for chemical synthesis in the condensed phase.

Warneke, Jonas↗
DOE OSTI2022

Chemical and Reactive Transport Processes Associated with Hydraulic Fracturing of Unconventional Oil/Gas Shales

Hydraulic fracturing of unconventional oil/gas shales has changed the energy landscape of the U.S.. Recovery of hydrocarbons from tight, hydraulically fractured shales is a highly inefficient process, with estimated recoveries of < 25% for natural gas and < 5% for oil. This review focuses on the complex chemical interactions of additives in hydraulic fracturing fluid (HFF) with minerals and organic matter in oil/gas shales. These interactions are intended to increase hydrocarbon recovery by increasing porosities and permeabilities of tight shales. However, fluid-shale interactions result in the dissolution of shale minerals and the release and transport of chemical components. They also result in mineral precipitation in the shale matrix, which can reduce permeability, porosity, and hydrocarbon recovery. Competition between mineral dissolution and mineral precipitation processes influences the amounts of oil and gas recovered. We review the temporal/spatial origins and distribution of unconventional oil/gas shales from mudstones and shales, followed by discussion of their global and U.S. distributions and compositional differences from different U.S. sedimentary basins. We discuss the major types of chemical additives in HFF with their intended purposes, including drilling muds. Fracture distribution, porosity, permeability, and the identity and molecular-level speciation of minerals and organic matter in oil/gas shales throughout the hydraulic fracturing process are discussed. Also discussed are analysis methods used in characterizing oil/gas shales before and after hydraulic fracturing, including permeametry and porosimetry measurements, X-ray diffraction/Rietveld refinement, X-ray computed tomography, scanning/transmission electron microscopy, and laboratory- and synchrotron-based imaging/spectroscopic methods. Reactive transport and spatial scaling are discussed in some detail in order to relate fundamental molecular-scale processes to fluid transport. Furthermore, our review concludes with a discussion of potential environmental impacts of hydraulic fracturing and important knowledge gaps that must be bridged to achieve improved mechanistic understanding of fluid transport in oil/gas shales.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2025

Micromechanical Surrogate Machine Learning Model for Creep Deformation Modeling

Process variability during the manufacture of gas turbine engine hot section components can significantly affect the material’s resulting microstructure. In casting, for instance, geometric variation within a component (thin sections versus thick sections, radial location) influences cooling rates and the resulting grain size. The high temperature creep response is known to be sensitive to grain size owing to a diffusional creep mechanism which occurs more readily along grain boundaries. Microstructural variation correspondingly drives mechanical behavior which propagates into component scale performance uncertainty. These factors are essential when planning inspection, maintenance, and repair strategies within a reliability framework. These benefits provide opportunities to increase overall energy efficiency through refined margins. Critically, there is an opportunity to bolster existing data-driven reliability models using physics-driven process-structure-property relations. Here we present recent work establishing a framework for evaluating the probabilistic creep performance of high-temperature materials. A novel microstructure-sensitive crystal plasticity finite element model is established that captures both grain boundary and crystallographic deformation effects. The computationally expensive physics model is calibrated using a statistical approach and this high-fidelity model is subsequently used to train a computationally efficient machine learning surrogate model. The surrogate model is essential for sampling a large ensemble of simulated structure-property pair results. The ensemble data are then mined to extract salient trends to be incorporated into a microstructure-sensitive reliability model. The proposed approach represents a novel way to capture microstructure-sensitive trends from physics-based models within a modern reliability framework.

Fernandez-Zelaia, Patxi [ORNL]↗