Search NASA⌕ Search

SEARCH · Search NASA

Results for “Rate formulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Pilot Sensitivity to Simulator Flight Dynamics Model Formulation for Stall Training

A piloted simulation study was performed in the Cockpit Motion Facility at the National Aeronautics and Space Administration Langley Research Center. The research was motivated by the desire to reduce the commercial transport airplane fatal accident rate due to in-flight loss of control. The purpose of this study, which focused on a generic T-tail transport airplane, was to assess pilot sensitivity to flight dynamics model formulation used during a simulator stall recognition and recovery training/demonstration profile. To accomplish this, the flight dynamics model was designed with many configuration options. The model options were based on recently acquired static and dynamic stability and control data from sources that included wind tunnel, water tunnel, and computational fluid dynamics. The results, which are specific to a transport airplane stall recognition and recovery guided demonstration scenario, showed the two most important aerodynamic effects (other than stick pusher) to model were stall roll- off and the longitudinal static stability characteristic associated with the pitch break.

Cunningham, Kevin↗

Steady-State Computation of Constant Rotational Rate Dynamic Stability Derivatives

Dynamic stability derivatives are essential to predicting the open and closed loop performance, stability, and controllability of aircraft. Computational determination of constant-rate dynamic stability derivatives (derivatives of aircraft forces and moments with respect to constant rotational rates) is currently performed indirectly with finite differencing of multiple time-accurate computational fluid dynamics solutions. Typical time-accurate solutions require excessive amounts of computational time to complete. Formulating Navier-Stokes (N-S) equations in a rotating noninertial reference frame and applying an automatic differentiation tool to the modified code has the potential for directly computing these derivatives with a single, much faster steady-state calculation. The ability to rapidly determine static and dynamic stability derivatives by computational methods can benefit multidisciplinary design methodologies and reduce dependency on wind tunnel measurements. The CFL3D thin-layer N-S computational fluid dynamics code was modified for this study to allow calculations on complex three-dimensional configurations with constant rotation rate components in all three axes. These CFL3D modifications also have direct application to rotorcraft and turbomachinery analyses. The modified CFL3D steady-state calculation is a new capability that showed excellent agreement with results calculated by a similar formulation. The application of automatic differentiation to CFL3D allows the static stability and body-axis rate derivatives to be calculated quickly and exactly.

Park, Michael A.↗

An Ecosystem Simulation Model for Methane Production and Emission from Wetlands

Previous experimental studies suggest that methane emission from wetland is influenced by multiple interactive pathways of gas production and transport through soil and sediment layers to the atmosphere. The objective of this study is to evaluate a new simulation model of methane production and emission in wetland soils that was developed initially to help identify key processes that regulate methanogenesis and net flux of CH4 to the air, but which is designed ultimately for regional simulation using remotely sensed inputs for land cover characteristics. The foundation for these computer simulations is based on a well-documented model (CASA) of ecosystem production and carbon cycling in the terrestrial blaspheme. Modifications to represent flooded wetland soils and anaerobic decomposition include three new sub-models for: (1) layered soil temperature and water table depth (WTD) as a function of daily climate drivers, (2) CH4 production within the anoxic soil layer as a function of WTD and CO2 production under poorly drained conditions, and (3) CH4 gaseous transport pathways (molecular diffusion, ebullition, and plant vascular transport) as a function of WTD and ecosystem type. The model was applied and tested using climate and ecological data to characterize tundra wetland sites near Fairbanks, Alaska studied previously by Whalen and Reeburgh. Comparison of model predictions to measurements of soil temperature and thaw depth, water-table depth, and CH4 emissions over a two year period suggest that inter-site differences in soil physical conditions and methane fluxes could be reproduced accurately for selected periods. Day-to-day comparison of predicted emissions to measured CH4 flux rates reveals good agreement during the early part of the thaw season, but the model tends to underestimate production of CH4 during the months of July and August in both test years. Important seasonal effects, including that of falling WTD during these periods, are apparently overlooked in the model formulation. Nevertheless, reasonably close agreement was achieved between the model's mean daily and seasonal estimates of CH4 flux and observed emission rates for northern wetland ecosystems. Several features of the model are identified as crucial to more accurate prediction of wetland methane emission, including the capacity to incorporate influences of localized topographic and hydrologic features on site-specific soil temperature and WTD dynamics, and mechanistic simulation of methane emission transport pathways from within the soil profile.

Potter, C. S.↗

Prediction of self-pressurization rate of cryogenic propellant tankage

The SOLA-ECLIPSE code is being developed to enable prediction of the behavior of cryogenic propellants in spacecraft tankage. A brief description of the formulations used for modeling heat transfer and for determining the thermodynamic state is presented. Code performance is verified through comparison to experimental data for the self-pressurization of scale-model liquid hydrogen tanks. SOLA-ECLIPSE is used to examine the effect of initial subcooling of the liquid phase on the self-pressurization rate of an on-orbit full-scale liquid hydrogen tank typical for a chemical-propulsion orbit transfer vehicle. The computational predictions show that even small amounts of subcooling will significantly decrease the self-pressurization rate. Further, if the cooling is provided by a thermodynamic vent system, it is concluded that small levels of subcooling will maximize propellant conservation.

Hochstein, John I.↗

Development of a boundary-layer-type solver based on simultaneous iteration technique for axisymmetric separated flows

A boundary-layer-type solver is developed for the numerical solution of axisymmetric separated flows. A new fully implicit coupling scheme for the viscous and inviscid regions is demonstrated. This fully implicit coupling technique is similar to the work of Carter, Veldman, and an extension of an earlier work of Halim and Hafez. A comparison is made for the convergence rate using this new fully implicit coupling technique and the semiimplicit coupling of Halim and Hafez. Numerical results using the fully implicit coupling are obtained for laminar incompressible separated flows, including a boattail and a series of trough geometries. Also, the near-wake flow problem is considered using the present formulation. A clear conclusion of this investigation is that the present scheme using the fully implicit coupling method converges at a faster rate than the semiimplicit coupling and the partially parabolized Navier-Stokes (PPNS) procedures.

Halim, A. A. M.↗

An OpenStreetMaps based tool to study the energy demand and emissions impact of electrification of medium and heavy-duty freight trucks

In this paper, we present the mathematical formulation of an OpenStreetMaps (OSM) based tool that compares the costs and emissions of long-haul medium and heavy-duty (M&HD) electric and diesel freight trucks, and determines the spatial distribution of added energy demand due to M&HD EVs. The optimization utilizes a combination of information on routes from OSM, utility rate design data across the United States, and freight volume data, to determine these values. In order to deal with the computational complexity of this problem, we formulate the problem as a convex optimization problem that is scalable to a large geographic area. In our analysis, we further evaluate various scenarios of utility rate design (energy charges) and EV penetration rate across different geographic regions and their impact on the operating cost and emissions of the freight trucks. Our approach determines the net emissions reduction benefits of freight electrification by considering the primary energy source in different regions. Such analysis will provide insights to policy makers in designing utility rates for electric vehicle supply equipment (EVSE) operators depending upon the specific geographic region and to electric utilities in deciding infrastructure upgrades based on the spatial distribution of the added energy demand of M&HD EVs. To showcase the results, a case study for the U.S. state of Texas is conducted.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Collisional damping rates for plasma waves

The distinction between the plasma dynamics dominated by collisional transport versus collective processes has never been rigorously addressed until recently. A recent paper [P. H. Yoon et al., Phys. Rev. E 93, 033203 (2016)] formulates for the first time, a unified kinetic theory in which collective processes and collisional dynamics are systematically incorporated from first principles. One of the outcomes of such a formalism is the rigorous derivation of collisional damping rates for Langmuir and ion-acoustic waves, which can be contrasted to the heuristic customary approach. However, the results are given only in formal mathematical expressions. The present brief communication numerically evaluates the rigorous collisional damping rates by considering the case of plasma particles with Maxwellian velocity distribution function so as to assess the consequence of the rigorous formalism in a quantitative manner. Comparison with the heuristic (“Spitzer”) formula shows that the accurate damping rates are much lower in magnitude than the conventional expression, which implies that the traditional approach over-estimates the importance of attenuation of plasma waves by collisional relaxation process. Such a finding may have a wide applicability ranging from laboratory to space and astrophysical plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

ASSESSMENT OF THE POTENTIAL FOR HYDROGEN GENERATION DURING GROUTING OPERATIONS IN THE R- AND P-REACTOR VESSELS

The R- and P-reactor buildings were retired from service and are now being prepared for deactivation and decommissioning (D&D). D&D activities will consist primarily of immobilizing contaminated components and structures in a grout-like formulation. Aluminum corrodes very rapidly when it comes in contact with the alkaline grout materials and as a result produces hydrogen gas. To address this potential deflagration/explosion hazard, the Materials Science and Technology Directorate (MS&T) of the Savannah River National Laboratory (SRNL) has been requested to review and evaluate existing experimental and analytical studies of this issue to determine if any process constraints on the chemistry of the fill material and the fill operation are necessary. Various options exist for the type of grout material that may be used for D&D of the reactor vessels. The grout formulation options include ceramicrete (pH 6-8), low pH portland cement + silica fume grout (pH 10.4), or Portland cement grout (pH 12.5). The assessment concluded that either ceramicrete or the silica fume grout may be used to safely grout the P-reactor vessel. The risk of accumulation of a flammable mixture of hydrogen between the grout-air interface and the top of the reactor is very low. Portland cement grout, on the other hand, for the same range of process parameters does not provide a significant margin of safety against the accumulation of flammable gas in the reactor vessel during grouting operations in the P-reactor vessel. It is recommended that this grout not be utilized for this task. The R-reactor vessel contains significantly less aluminum and thus a Portland cement grout may be considered as well. For example, if the grout fill rate is less than 1 inch/min and the grout temperature is maintained at 70 C or less, the risk of hydrogen accumulation in the R-reactor vessel is very low for the Portland cement. Alternatively, if the grout fill rate is less than 0.5 inch/min and the grout is maintained at a temperature of 80 C, the risk will again be very low. Although these calculations are conservative, there are some measures that may be taken to further minimize the potential for hydrogen evolution. (1) Minimize the temperature of the grout as much as practical. Lower temperatures will mean lower hydrogen generation rates. For P-reactor, grout temperatures less than 100 C should provide an adequate safety margin for the pH 8 and pH 10.4 grout formulations. For R-reactor, grout temperatures less than 70 C or 80 C will provide an adequate safety margin for the Portland cement. The other grout formulations are also viable options for R-reactor. (2) Minimize the grout fill rate as much as practical. Lowering the fill rate takes advantage of passivation of the aluminum components and hence lower hydrogen generation rates. For P-reactor, fill rates that are less than 2 inches/min for the ceramicrete and the silica fume grouts will reduce the chance of significant hydrogen accumulation. For R-reactor, fill rates less than 1 inch/min will again minimize the risk of hydrogen accumulation. (3) Ventilate the building as much as practical (e.g., leave doors open) to further disperse hydrogen. The volumetric hydrogen generation rates in the P-reactor vessel, however, are low for the pH 8 and pH 10.4 grout, (i.e., less than 0.32 ft{sup 3}/min). If further walk-down inspections of the reactor vessels suggest an increase in the actual areal density of aluminum, the calculations should be re-visited.

08 HYDROGEN↗

A novel transformation of the ice sheet Stokes equations and some of its properties and applications

We introduce a novel transformation of the Stokes equations into a form closely resembling the shallow Blatter–Pattyn equations. The two forms differ by only a few additional terms, while their variational formulations differ only by a single term in each horizontal direction. Specifically, the variational formulation of the Blatter–Pattyn model drops the vertical velocity in the second invariant of the strain rate tensor. Here we make use of the new transformation in two ways. First, we consider incorporating the transformed equations into a code that can be very easily converted from a Stokes to a Blatter–Pattyn model, and vice versa, by switching these terms on or off. This may be generalized so that the Stokes model is switched on adaptively only where the Blatter–Pattyn model loses accuracy. Second, the key role played by the vertical velocity in the Blatter–Pattyn approximation motivates new approximations. Two examples are presented. These require a mesh that enables the discrete continuity equation to be invertible for the vertical velocity in terms of the horizontal velocity components. Examples of such meshes, such as the first-order P1–E0 mesh and the second-order P2–E1 mesh, are given in both 2D and 3D. However, the transformed Stokes model has the same type of gravity forcing as the Blatter–Pattyn model, determined by the ice surface slope, thereby forgoing some of the mesh generality of the traditional formulation of the Stokes model.

58 GEOSCIENCES↗

Assessment of Enthalpy-Based Conditional Moment Closure Models in Predicting Ignition of Lean and Stoichiometric PRF-Air Mixtures with Temperature Inhomogeneity

Accurate prediction of the ignition delay in turbulent flows is important in developing advanced combustion technology for internal combustion engines. Enthalpy-based conditional moment closure (CMC) models are assessed with 2-D direct numerical simulation (DNS) data for ignition of homogeneous PRF-air mixtures with temperature inhomogeneity in homogeneous isotropic turbulence. The sensible-enthalpy-based CMC model is compared with the total-enthalpy-based formulation, with the focus being placed on assessing the capability of the CMC models in predicting ignition processes under different engine conditions. A priori analysis shows that the total-enthalpy-based CMC gives good predictions of the heat release rates in the lean mixtures when the temperature inhomogeneity level is low, but leads to significant overprediction under the stoichiometric condition regardless of the thermal stratification levels. On the other hand, the sensible enthalpy formulation performs well for all conditions considered in this study due to the suppressed conditional temperature fluctuations. A mapping method to model conditional scalar dissipation rates and probability density function of sensible enthalpy is also assessed.

Wang, Wei↗

High Level Waste Vitrification System Improvements (Final Report)

This report describes work conducted to support the development and testing of new glass formulations that extend beyond those that have been previously investigated for the Hanford Waste Treatment and Immobilization Plant (WTP). The principal objective was to investigate maximization of the incorporation of several waste components that are expected to limit waste loading and, consequently, high level waste (HLW) processing rates and canister count. The work was performed with four waste compositions specified by the Office of River Protection (ORP); these wastes contain high concentrations of bismuth, chromium, aluminum, and aluminum plus sodium. The tests were designed to identify glass formulations that maximize waste loading while meeting all processing and product quality requirements. The work included preparation and characterization of crucible melts in support of subsequent DuraMelter 100 (DM100) tests designed to examine the effects of enhanced glass formulations, increased glass processing temperature, increased crystallinity, and feed solids content on waste processing rate and product quality.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Cloud-generated radiative heating and its generation of available potential energy

The generation of zonal available potential energy (APE) by cloud radiative heating is discussed. The APE concept was mathematically formulated by Lorenz (1955) as a measure of the maximum amount of total potential energy that is available for conversion by adiabatic processes to kinetic energy. The rate of change of APE is the rate of the generation of APE minus the rate of conversion between potential and kinetic energy. By radiative transfer calculations, a mean cloud-generated radiative heating for a well defined set of cloud classes is derived as a function of cloud optical thickness. The formulation is suitable for using a general cloud parameter data set and has the advantage of taking into account nonlinearities between the microphysical and macrophysical cloud properties and the related radiation field.

Stuhlmann, R.↗

Ni and Cr addition to alloy waste forms to reduce radionuclide environmental releases

Reference alloy waste forms (RAW) were fabricated and underwent hybrid corrosion/immersion testing to parameterize the ANL analytical oxidative-dissolution model to enable the calculation of fractional release rates and to determine the effectiveness of Ni and Cr trim additions in reducing release rates of radionuclide surrogates. Figure 1 shows the prototypical multiphase microstructure of the alloys with each phase type contributing about equally to the exposed surface area. The waste forms tested at SRNL were variations of the RAW-6 formulation that uses HT9 as the main alloy component, and are meant to enable evaluation of the impact of Ni and Cr trim additions on the release rates of actinides and Tc-99. The test solutions were deaerated alkaline and acidic brines, ranging in pH 3 to pH 10, representing potential repositories with those conditions. The testing approach consisted of 4 major steps; 1) bare surface corrosion measurements at pH values of 3, 5, 8, and 10, 2) hybrid potentiostatic hold/exposure measurements at pH 3, 3) measurement of radionuclide concentrations and relations to anodic current from potentiostatic holds, and 4) identification of corroding phases using SEM/EDS of electrodes.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A Nonlocal Progressive Damage Model for Composite Materials

Fiber reinforced composite materials are widely used in aerospace structures due to their high specific stiffness and strength. These materials exhibit complex deformation, damage and failure mechanisms under high strain rate loading conditions. Many different failure criteria have been proposed in literature to describe the damage initiation and evolution of fiber reinforced composite materials. Most of these damage models are based on a local framework. In a local framework, the material behavior is based on a point-wise constitutive relation which is independent of the effect of the surrounding points. These models include stiffness degradation when damage initiates in the material, which within a local framework leads to a highly mesh dependent result. This could be overcome using a nonlocal finite element approach. In the current work, a nonlocal formulation based on the work by Andrade et al [1] is adapted to describe composite material behavior. The LS-DYNA rate dependent progressive damage model, MAT162 is employed to detect the initiation and evolution of damage in orthotropic composite materials. This model is developed as a FORTRAN user material subroutine in the LS-DYNA environment. The results of MAT162 with and without the nonlocal formulation are compared at different mesh densities to validate the model. The numerical analysis exhibits the advantages of the nonlocal formulation.

Kodagali, Karan↗

Vapour phase approach for iron oxide nanoparticle synthesis from solid precursors

A new non-solution mediated approach to the synthesis of iron oxide nanoparticles directly from solid FeCl{sub 2} salt precursors has been developed. The method is rapid, simple and scalable. The structural properties and the phase of the resulting iron oxide particles has been determined by a range of methods including XRD, FT-IR and Mössbauer spectroscopy, and the phase is shown to be maghemite (γ-Fe{sub 2}O{sub 3}). The magnetic properties of the iron oxide particles have been measured using SQUID, confirming superparamagnetic behaviour of the powder and a saturation magnetization of 53.0 emu g{sup −1} at 300 K. Aqueous dispersions at increasing concentrations were prepared and their heating rate under a 400 kHz alternating magnetic field measured. The specific absorption rate (SAR) of the iron oxide was found to be 84.8 W g{sup −1}, which makes the material suitable for the formulation of ferrofluids or ferrogels with RF heating properties. - Graphical Abstract: Superparamagnetic iron oxide nanoparticles obtained by a novel vapour phase approach. Highlights: ► Novel vapour phase (non-solvent) approach for iron oxide nanoparticle synthesis. ► Attractive alternative approach to the present co-precipitation method. ► Better magnetic properties with high coercivity of nanoparticles. ► A high specific absorption rate (SAR) for hyperthermia applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Precipitate Phase Stability and Mechanical Properties of Alloy 263 and Variants in Wrought or Cast Form

Alloy 263 is a candidate Ni-based superalloy for use in advanced ultra-supercritical (AUSC) power plants that are targeted to operate above 700 °C. Exposure times in this type of environment are considerable with target creep properties specified at 100,000 h making phase stability an important parameter in the alloy selection process. In this investigation, the microstructure of alloy 263 and two modified compositions in both cast and cast/wrought forms were investigated after exposure at 800 °C for various times ranging from 1,000 h to 10,000 h. Tension and creep properties were assessed for all alloys in both forms. Modification to the Ti and Al concentrations successfully slowed down the γ' to η transformation while doubling the γ' fraction. Thin elongated η needles or platelets formed in the wrought products while thicker, plate-like, η precipitates were found in the castings. The effect of the various microstructures on the creep properties were determined using isothermally aged specimens aged at 800 °C for 3,000 h and 10,000 h prior to creep screening. Strong precipitation of the η phase was found to considerably decrease creep life and increase minimum creep rate. By modifying the Ti and Al content, the creep life and ductility of the new formulation tested on specimens isothermally aged for 3,000 and 10,000 h were near that of the nominal alloy in its standard aged condition.

Detrois, Martin↗

Mobility size and mass of nascent soot particles in a benchmark premixed ethylene flame

The burner stabilized stagnation flame technique coupled with micro-orifice probe sampling and mobility sizing has evolved into a useful tool for examining the evolution of the particle size distribution of nascent soot in laminar premixed flames. Several key aspects of this technique are examined through a multi-university collaborative study that involves both experimental measurement and computational modeling. Key issues examined include (a) data reproducibility and facility effects using four burners of different sizes and makers over three different facilities, (b) the mobility diameter and particle mass relationship, and (c) the degree to which the finite orifice flow rate affects the validity of the boundary condition in a pseudo one dimensional stagnation flow flame formulation. The results indicate that different burners across facilities yield nearly identical results after special attention is paid to a range of experimental details, including a proper selection of the sample dilution ratio and quantification of the experimental flame boundary conditions. The mobility size and mass relationship probed by tandem mass and mobility measurement shows that nascent soot with mobility diameter as small as 15 nm can deviate drastically from the spherical shape. Various non-spherical morphology models using a mass density value of 1.5 g/cm 3 can reconcile this discrepancy in nascent soot mass. Lastly, two-dimensional axisymmetric simulations of the experimental flame with and without the sample orifice flow reveal several problems of the pseudo one-dimensional stagnation flow flame approximation. The effect of the orifice flow on the flame and soot sampled, although small, is not negligible. Particular suggestions are provided as to how to treat the non-ideality of the experimental setup in experiment and model comparisons.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗