Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS CORROSION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Magnetic Field Optimization of an In-Vacuum Undulator at NSLS-II Transactions on Applied Superconductivity

A 3.0 m long In-Vacuum Undulator (IVU) is employed at the National Synchrotron Light Source II (NSLS-II) for the Hard X-ray Nanoprobe (HXN) beamline providing structural and X-ray fluorescence imaging with world-leading spatial resolution. On July 1 st 2018 a gearbox shaft in the gap drive train assembly sheared due to corrosion fatigue caused by stress due to mechanical misalignment. Furthermore, the device was extracted from the storage ring and measured. The magnetic field measurements detected a degradation of the magnetic performance as well as a localized demagnetization of the magnetic modules of the first 3 upstream periods. We describe here the mechanical repairs and the magnetic phase shimming optimization implemented to restore the spectral performance of the device.

43 PARTICLE ACCELERATORS↗

Millimeter-Wave Thermal Analysis Development and Application to GEN IV Reactor Materials

New millimeter-wave thermal analysis instrumentation has been developed and studied for characterization of materials required for diverse fuel and structural needs in high temperature reactor environments such as the Next Generation Nuclear Plant (NGNP). A two-receiver 137 GHz system with orthogonal polarizations for anisotropic resolution of material properties has been implemented at MIT. The system was tested with graphite and silicon carbide specimens at temperatures up to 1300 ºC inside an electric furnace. The analytic and hardware basis for active millimeter-wave radiometry of reactor materials at high temperature has been established. Real-time, non contact measurement sensitivity to anisotropic surface emissivity and submillimeter surface displacement was demonstrated. The 137 GHz emissivity of reactor grade graphite (NBG17) from SGL Group was found to be low, ~ 5 %, in the 500 – 1200 °C range and increases by a factor of 2 to 4 with small linear grooves simulating fracturing. The low graphite emissivity would make millimeter-wave active radiometry a sensitive diagnostic of graphite changes due to environmentally induced stress fracturing, swelling, or corrosion. The silicon carbide tested from Ortek, Inc. was found to have a much higher emissivity at 137 GHz of ~90% Thin coatings of silicon carbide on reactor grade graphite supplied by SGL Group were found to be mostly transparent to millimeter-waves, increasing the 137 GHz emissivity of the coated reactor grade graphite to about ~14% at 1250 ºC.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Repair and Retuning of 3-m long In-Vacuum Undulator at NSLS-II

A 3.0 m long In-Vacuum Undulator (IVU) is employed at the National Synchrotron Light Source II (NSLS-II) for the Hard X-ray Nanoprobe (HXN) beamline providing structural and X-ray fluorescence imaging with world-leading spatial resolution. On July 1st 2018 a gearbox shaft in the gap drive train assembly sheared due to corrosion fatigue caused by stress due to mechanical misalignment. The device was extracted from the storage ring and measured. The magnetic field measurements detected a degradation of the magnetic performance as well as a localized demagnetization of the magnetic modules of the first 3 upstream periods. This paper describes the mechanical repairs and the magnetic phase shimming optimization implemented to restore the spectral performance of the device.

36 MATERIALS SCIENCE↗

Corrosion-resistant multilayer coatings for the 28-75 nm wavelength region

Corrosion has prevented use of SiC/Mg multilayers in applications requiring good lifetime stability. We have developed Al-based barrier layers that dramatically reduce corrosion, while preserving high reflectance and low stress. The aforementioned advances may enable the implementation of corrosion-resistant, high-performance SiC/Mg coatings in the 28-75 nm region in applications such as tabletop EUV/soft x-ray laser sources and solar physics telescopes. Further study and optimization of corrosion barrier structures and coating designs is underway.

36 MATERIALS SCIENCE↗

Comparative Study of Oxides Formed on Fusion Zone and Base Metal of Laser Welded Zr-1.0Sn-1.0Nb-0.1Fe Alloy

Numerous studies have primarily focused on the corrosion mechanism of zirconium alloy base metal. However, the corrosion resistance of weld beads or seams is of vital importance in the degradation of structural components in the reactor. In the present work, the corrosion resistance of the fusion zone and base metal of laser welded zirconium alloy joints was comparatively investigated. The microstructure morphologies, phase structures and strain fields of oxide films formed on fusion zone and base metal were observed and analyzed. The oxide thickness of the fusion zone was thicker than that of the base metal with prolonged corrosion. Compared to the base metal, the lower density of dislocations and level of strain values in the oxide film of the fusion zone indicated that the stress in the oxide film was lower. The phase transition from the tetragonal ZrO{sub 2} to the monoclinic ZrO{sub 2} could be suppressed due to the high level of stress, resulting in the better corrosion resistance of the base metal. Moreover, the second phase particles and non-βZr phase in the base metal contributed to the better corrosion resistance.

36 MATERIALS SCIENCE↗

Numerical simulation of transient moisture transfer into an electronic enclosure

Electronic systems are sometimes exposed to harsh environmental conditions of temperature and humidity. Moisture transfer into electronic enclosures and condensation can cause several problems such as corrosion and alteration in thermal stresses. It is therefore essential to study the local climate inside the enclosures to be able to protect the electronic systems. In this work, moisture transfer into a typical electronic enclosure is numerically studied using CFD. In order to reduce the CPU-time and make a way for subsequent factorial design analysis, a simplifying modification is applied in which the real 3D geometry is approximated by a 2D axial symmetry one. The results for 2D and 3D models were compared in order to calibrate the 2D representation. Furthermore, simulation results were compared with experimental data and good agreement was found.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

In situ Bragg coherent X-ray diffraction imaging of corrosion in a Co–Fe alloy microcrystal

Corrosion is a major concern for many industries, as corrosive environments can induce structural and morphological changes that lead to material dissolution and accelerate material failure. The progression of corrosion depends on nanoscale morphology, stress, and defects present. Experimentally monitoring this complex interplay is challenging. Here we implement in situ Bragg coherent X-ray diffraction imaging (BCDI) to probe the dissolution of a Co-Fe alloy microcrystal exposed to hydrochloric acid (HCl). By measuring five Bragg reflections from a single isolated microcrystal at ambient conditions, we compare the full three-dimensional (3D) strain state before corrosion and the strain along the [111] direction throughout the corrosion process. We find that the strained surface layer of the crystal dissolves to leave a progressively less strained surface. Interestingly, the average strain closer to the centre of the crystal increases during the corrosion process. We determine the localised corrosion rate from BCDI data, revealing the preferential dissolution of facets more exposed to the acid stream, highlighting an experimental geometry effect. These results bring new perspectives to understanding the interplay between crystal strain, morphology, and corrosion; a prerequisite for the design of more corrosion-resistant materials.

36 MATERIALS SCIENCE↗

Burst pressure models and validations for thick-walled pipelines containing corrosion defects

Corrosion is one major threat to pipeline integrity. Over the past decades, many corrosion models have been developed for determining the remaining strength of corroded pipelines, including ASME B31.G, Modified B31.G, LPC, PCORRC and their modified models. All these corrosion models are applicable only to large diameter, thin-walled pipelines with a diameter to wall thickness ratio D/t ≥ 20. In practice, many pipelines have a small diameter and thick wall with a D/t ratio < 20, and thus an adequate corrosion model is needed for assessing remaining strength for corroded thick-walled pipelines. This paper briefly reviews the theoretical burst pressure models for defect-free thin and thick-walled pipelines and four representative corrosion assessment models for thin-walled corroded pipelines. On this basis, two modified corrosion models are proposed to thick-walled pipelines in terms of the average shear stress yield theory. To verify the proposed corrosion models, comprehensive validations are performed. Numerical validations include the elastic-plastic finite element analysis to determine burst pressure for pipelines without and with corrosion defects and the model evaluation using a large dataset of available FEA results of burst pressure for machined defects. Experimental validations include a set of burst pressure tests for defect-free thick-walled pipes with different thicknesses and the model evaluation using one large burst dataset for machined defects with flat bottoms and another large dataset for real corrosion defects with curved river bottom profiles. Both numerical and experimental validations show that the proposed corrosion models can more accurately predict the remaining strength for corroded thin and thick-walled pipelines.

Pipeline↗

Electrochemical Corrosion Behavior of 5083 Aluminum Alloy Subjected to Laser Shock Peening

This paper investigates the effect of ablative coating used during laser shock peening (LSP) on corrosion behavior of 5083 aluminum alloy in artificial seawater. Micro-hardness, residual stress, and surface morphology of the specimens were measured. The corrosion behavior was investigated by electrochemical test. Surface corrosion morphologies after electrochemical tests were examined by SEM and EDS. The results show that surface roughness and surface compressive residual stress of the specimen treated by LSP without ablative coating (LSPwC) are lower than that of the specimen treated by LSP with ablative coating under the same laser energy. The open-circuit potentials and self-corrosion potentials of the specimens treated by LSP and LSPwC both shift positively, and the diameters of the capacitor arcs were larger after LSP and LSPwC. The corrosion resistance of 5083 aluminum alloy is improved by LSP and LSPwC. Moreover, superior corrosion resistance is achieved without using the ablative coating during LSP.

36 MATERIALS SCIENCE↗

Mechanical and Microstructural Characterization of Low-Temperature Neutron Irradiated Zircaloy-4

Zr-based alloys, namely Zircaloy-2, Zircaloy-4, ZIRLO, or M5, have been used in light water reactors (LWRs) as structural materials (cladding, pressure tubes, and etc.). Under irradiation conditions, especially at harsh pressurized water reactor (PWR) conditions, these Zr alloys can undergo embrittlement due to corrosion, hydriding, and irradiation induced stresses. This ultimately leads to the severe degradation of Zr-alloys and increase the probability of fuel failure. While various research efforts have been conducted in developing better Zr-based alloys to withstand these harsh environments, there is a considerable amount of Zr-alloy characteristics, such as change in mechanical properties under irradiation conditions and its relationship to the materials microstructure, that need to be studied. This present study has focused on investigation of mechanical and microstructural properties of Zircaloy-4 under low temperature (80 - 100 deg. C) neutron irradiation conditions. Some of the samples studied were also hydrided to evaluate influence of hydride precipitates in the material. (authors)

36 MATERIALS SCIENCE↗

Development of Surveillance Test Articles for Materials Degradation Management in MSR Environment

Information on materials degradations during advanced reactor operations is limited Effects of materials degradations during reactor operations are synergistic, involving: Irradiation, corrosion, elevated temperature exposure and stress (creep-fatigue loading) Establishment of surrogate materials surveillance program for the management of materials degradations would be an important pathway in support of the timely licensing of advanced reactors

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The Effect of Flowing Velocity and Impact Angle on the Fluid-Accelerated Corrosion of X65 Pipeline Steel in a Wet Gas Environment Containing CO{sub 2}

This study investigated the effect of flowing velocity and impact angle on the fluid-accelerated corrosion (FAC) of X65 pipeline steel in a wet CO{sub 2}-containing environment by corrosion morphology analysis, electrochemical measurement, and hydromechanical numerical analysis. It has been found that the corrosion behavior was controlled by the ion diffusion rate and shear stress due to the flowing gas. With an increase in the flowing velocity, the pitting corrosion initially decreased and then increased when the flowing velocity exceeded 14 m/s; this increase is caused by the augmentation of shear stress. When the impact angle decreased, the position of serious corrosion gradually moved outwards.

36 MATERIALS SCIENCE↗

Measurement and modeling of strain fields in zirconium hydrides precipitated at a stress concentration

Hydrogen adsorption into zirconium, as a result of corrosion in aqueous environments, leads to the precipitation of a secondary brittle hydride phase. These hydrides tend to first form at stress concentrations such as fretting flaws or cracks in engineering components, potentially degrading the structural integrity of the component. One mechanism for component failure is a slow crack growth mechanism known as Delayed Hydride Cracking (DHC), where hydride fracture occurs followed by crack arrest in the ductile zirconium matrix. The current work employs both an experimental and a modeling approach to better characterize the effects and behavior of hydride precipitation at such stress concentrations. Strains around stress concentrations containing hydrides were mapped using High Energy X-ray Diffraction (HEXRD). These studies highlighted important differences in the behavior of the hydride phase and the surrounding zirconium matrix, as well as the strain associated with the precipitation of the hydride. A finite element model was also developed and compared to the X-ray strain mapping results. This model provided greater insight into details that could not be obtained directly from the experimental approaches, as well as providing a framework for future modeling to predict the effects of hydride precipitation under varied conditions.

08 HYDROGEN↗

Response relationship between loading condition and corrosion fatigue behavior of nickel-aluminum bronze alloy and its crack tip damage mechanism

Highlights: • The differences of corrosion fatigue behavior of NAB alloy in air and in 3.5% NaCl solution are carefully compared. • The corrosion environment significantly accelerates the crack growth of NAB alloy and decreases the fatigue threshold. • The corrosion fatigue crack growth rate increases with the decrease of loading frequency. • The acidification and the dealumination occur in process of corrosion fatigue, resulting in the deterioration of crack tip. - Abstract: Corrosion fatigue is one of the major forms for nickel‑aluminum bronze alloy used in marine propeller. It is greatly important to understand the corrosion fatigue behavior of nickel‑aluminum bronze alloy in seawater for the purpose of improving the service life of marine equipment. In this study, corrosion fatigue crack growth rate of nickel‑aluminum bronze alloy in 3.5% NaCl solution was tested under various stress intensity factors, stress ratios and loading frequencies to reveal its corrosion fatigue mechanism. The results show that corrosion environment significantly accelerates the crack growth and decreases the corrosion fatigue threshold, which is attributed to the corrosion reactions between the metals of crack tip and corrosive medium. Among the various factors, loading frequency has more predominant influence on the corrosion fatigue crack growth rate of nickel‑aluminum bronze alloy, which can be rationally explained by the hydrogen embrittlement mechanism. Additionally, in the process of corrosion fatigue crack growth, the acidification and the dealumination would occur at the crack tip, resulting in the corrosion dissolution of κ phases and the deterioration in mechanical properties of crack tip.

36 MATERIALS SCIENCE↗

Study on the corrosion residual strength of the 1.0 wt.% Ce modified AZ91 magnesium alloy

The effect of corrosion on the tensile behaviour of the 1.0 wt.% Ce modified AZ91 magnesium alloy was investigated by the immersion of the test bar in 3.5 wt.% NaCl aqueous solution for 0, 12, 40, 108, 204, 372 and 468 h with the subsequent tensile tests in this paper. The fractography was analyzed by scanning electron microscopy. The results show that pitting corrosion should be responsible for the drop of the corrosion residual strength within the testing time. The depth of the corrosion pits was statistically and quantitatively obtained by an optical microscopy and the maximal value was recorded as the extreme depth of the corrosion pit. Furthermore, the corrosion residual strength is linearly dependent on the extreme depth of the corrosion pit, which can be attributed to the loss of cross-sectional area and the emergence of stress concentration caused by the initiation and development of corrosion pits.

36 MATERIALS SCIENCE↗

Phase-field model of pitting corrosion kinetics in metallic materials

This study presents a thermodynamically consistent phase field model for the quantitative prediction of the pitting corrosion kinetics in metallic materials. An order parameter is introduced to represent the metal’s physical state at each point in the entire domain. The free energy of the metal-electrolyte system is defined in terms of its metal ion concentration and the order parameter. The mass transport in the electrolyte and the electrochemical reactions in the electrolyte/metal interface are taken into consideration in the model to simulate metal corrosion in a corrosive environment. The governing equations for mass transport and the order parameter are solved in such a manner that the system’s free energy is reduced as a result of diffusion and migration processes, and the distribution of electrostatic potential is governed by Poisson’s equation. A calibration study is performed to couple the kinetic interface parameter with the corrosion current density, which results in a direct relationship between overpotential and the kinetic interface parameter. A comparative study is performed to validate the phase field model against the experimental results. Several case studies are also examined to understand the corrosion behavior of closely located pits, stressed material, ceramic particles-reinforced steel, and crystallographic orientation dependence.

36 MATERIALS SCIENCE↗

Degradation of Ionic Pathway in PEM Fuel Cell Cathode

The degradation of the ionic pathway throughout the catalyst layer in proton exchange membrane fuel cells was studied under an accelerated stress test of catalyst support (potential hold at 1.2 V). Electrochemical behaviors of the cathode based on graphitic mesoporous carbon supported Pt catalyst were examined using electrochemical impedance spectroscopy and cyclic voltammetry. Impedance data were plotted and expressed in the complex capacitance form to determine useful parameters in the transmission line model: the double-layer capacitance, peak frequency, and ionic resistance. Electrochemical surface area and hydrogen crossover current through the membrane were estimated from cyclic voltammogram, while cathode Faradaic resistance was compared with ionic resistance as a function of test time. It was observed that during an accelerated stress test of catalyst support, graphitic mesoporous carbon becomes hydrophilic which increases interfacial area between the ionomer and the catalyst up to 100 h. However, the ionic resistance in the catalyst layer drastically increases after 100 h with further carbon support oxidation. The underlying mechanism has been studied and it was found that significant degradation of ionic pathway throughout the catalyst layer due to catalyst support corrosion induces uneven hydration and mechanical stress in the ionomer.

08 HYDROGEN↗