Search NASA⌕ Search

SEARCH · Search NASA

Results for “Shuttle”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Preflight status of the External Tank portion of the Space Shuttle Main Propulsion System

The development progress of the External Tank (ET) of the Shuttle Main Propulsion System (MPS) is described. 87% of ET propulsion components have satisfactorily completed qualification tests in preparation for the first Shuttle flight and their performance has been verified in the Main Propulsion Test Article (MPTA) firings of up to 100 seconds duration. The design changes in the LH2 tank pressurant diffuser, the LO2 feed system, and the ground test LO2 tank are discussed. Propellant loading information from MPTA tests may be used to predict loading operations and performance at KSC and VAFB, while ullage pressure profiles and boil-off rates during loading, chilldown rates, and final bulk density data have been obtained with geyser suppression evaluated and loading procedures established and verified. The MPTA test experience provided data to evaluate pressurization system and ET to Orbiter interface propellant performance noting thus that the fluid interface requirements will be satisfied for the first Shuttle flight. The Intertank inerting system was found to be effective in minimizing hazardous gas mixtures and full scale separation tests of the ET to Ground Umbilical Carrier Plate system were successfully completed.

Norquist, L.↗

Shuttle orbital flight test

The initial orbital flight of the shuttle vehicle will involve several operational aspects which differ from previous manned space programs. The asymmetrical shuttle launch configuration undergoes unique aero and thrust loads. The orbiter requires a complex interactive control system during entry. Techniques are described which will be used to minimize the ascent loads. Procedures are outlined which should maximize the entry control margins. The primary objective of the first shuttle flight is to obtain data from which to extract the loads and stability derivatives. Accomplishment of this objective will enable relaxation of constraints on launch winds, entry center of gravity, and crossrange during subsequent flights.

North, W. J.↗

Small orbital transfer vehicle for shuttle operations

Small orbital transfer vehicles to place payloads in orbits with altitudes above those of the standard Shuttle operation are studied. Low energy earth orbits below those of the planned spinning solid upper stages are addressed. Tandem and clustered solids are considered along with controlled solids, monopropellant and bipropellant liquids, and staged solid/liquid combinations. The performance, airborne support equipment, and program costs for the selected candidate concepts are presented. The results show that the most economical way to deliver the low energy payloads is with a modular liquid bipropellant stage system for the large majority of the payloads. The remainder of the payloads would use the Shuttle with integral OMS and Scout from WTR for a few specialized payloads until the Shuttle is operational at WTR.

Sibila, A. I.↗

Shuttle Global Positioning (GPS) System design study

Investigations of certain aspects and problems of the shuttle global positioning system GPS, are presented. Included are: test philosophy and test outline; development of a phase slope specification for the shuttle GPS antenna; an investigation of the shuttle jamming vulnerability; and an expression for the GPS signal to noise density ratio for the thermal protection system.

Nilsen, P.↗

A survey of load methodologies for shuttle orbiter payloads

Loads methods currently being used to design shuttle orbiter payloads are summarized. Methods used for the design of payloads launched by expendable launch vehicles are described in historical perspective. Experiences gained from expendable launch vehicle payloads are used to develop methodologies for the space shuttle orbiter payloads. The objectives for the development of a new methodology for the shuttle payloads are to reduce the cost and schedule for the payload load analysis by decoupling the payload analysis from the launch vehicle to the maximum extent possible. Methods are described for payload member load estimation or obtaining upper bounds for dynamic loads, as well as load prediction or calculating actual transient member load time histories.

Chen, J. C.↗

Evolution of the Shuttle extravehicular mobility unit

This paper deals briefly with the emergence of space suits as an important factor in supporting space missions but focuses mainly on the conceptual design of the Shuttle EMU (extravehicular mobility unit). Factors covering the criteria for the design approach are discussed. Several of the more specific subjects concerning the configuration selected are stressed; the EMU operating pressure, simplicity in don/doff, male/female sizing, components' useful life and the complexity surrounding the support of multi-year missions throughout the Shuttle program duration. In addition, comparisons with past EMU programs are made including a detailed discussion of how the Shuttle application and requirements drove and made this configuration a significant departure from previous EMU systems.

Correale, J. V.↗

Mission analysis for earth atmospheric measurements using a Shuttle-Spacelab lidar system

Orbital characteristics and launch conditions of a spaceborne lidar system proposed for a Shuttle Spacelab mission are analyzed. Mission design tradeoffs between instrument fields of view, resolutions, orbit groundtrack repetition parameters (Q), and orbital altitudes are shown. In the multi-experiment application of the Spacelab-lidar system, where scene illumination is the key mission parameter for the performance of the lidar instrument, results indicate that selected daytime or nighttime coverage can be programmed into Spacelab lidar missions by a judicious selection of Shuttle launch time. In addition to controlling the location of nighttime measurements, results indicate that, by the proper selection of Shuttle launch time, the magnitude and variability of solar lighting angles can be optimized to fit the requirements of the Spacelab lidar experiments.

Lawrence, G. F.↗

Subsonic stability and control flight test results of the Space Shuttle /tail cone off/

The subsonic stability and control testing of the Space Shuttle Orbiter in its two test flights in the tailcone-off configuration is discussed, and test results are presented. Flight test maneuvers were designed to maximize the quality and quantity of stability and control data in the minimal time allotted using the Space Shuttle Functional Simulator and the Modified Maximum Likelihood Estimator (MMLE) programs, and coefficients were determined from standard sensor data sets using the MMLE, despite problems encountered in timing due to the different measurement systems used. Results are included for lateral directional and longitudinal maneuvers as well as the Space Shuttle aerodynamic data base obtained using the results of wind tunnel tests. The flight test data are found to permit greater confidence in the data base since the differences found are well within control system capability. It is suggested that the areas of major differences, including lateral directional data with open speedbrake, roll due to rudder and normal force due to elevon, be investigated in any further subsonic flight testing. Improvements in sensor data and data handling techniques for future orbital test flights are indicated.

Cooke, D. R.↗

Space shuttle simulation model

The effects of atmospheric turbulence in both horizontal and near horizontal flight, during the return of the space shuttle, are important for determining design, control, and 'pilot-in-the-loop' effects. A nonrecursive model (based on von Karman spectra) for atmospheric turbulence along the flight path of the shuttle orbiter was developed which provides for simulation of instantaneous vertical and horizontal gusts at the vehicle center-of-gravity, and also for simulation of instantaneous gust gradients. Based on this model, the time series for both gusts and gust gradients were generated and stored on a series of magnetic tapes which are entitled shuttle simulation turbulence tapes (SSTT). The time series are designed to represent atmospheric turbulence from ground level to an altitude of 10,000 meters. The turbulence generation procedure is described as well as the results of validating the simulated turbulence. Conclusions and recommendations are presented and references cited. The tabulated one dimensional von Karman spectra and the results of spectral and statistical analyses of the SSTT are contained in the appendix.

Tatom, F. B.↗

Nonlinear dynamic response of a uni-directional model for the tile/pad space shuttle thermal protection system

A unidirectional analysis of the nonlinear dynamic behavior of the space shuttle tile/pad thermal protection system is developed and examined for imposed sinusoidal and random motions of the shuttle skin and/or applied tile pressure. The analysis accounts for the highly nonlinear stiffening hysteresis and viscous behavior of the pad which joins the tile to the shuttle skin. Where available, experimental data are used to confirm the validity of the analysis. Both analytical and experimental studies reveal that the system resonant frequency is very high for low amplitude oscillations but decreases rapidly to a minimum value with increasing amplitude. Analytical studies indicate that with still higher amplitude the resonant frequency increases slowly. The nonlinear pad is also responsible for the analytically and experimentally observed distorted response wave shapes having high sharp peaks when the system is subject to sinusoidal loads. Furthermore, energy dissipation in the pad is studied analytically and it is found that the energy dissipated is sufficiently high to cause rapid decay of dynamic transients. Nevertheless, the sharp peaked nonlinear responses of the system lead to higher magnification factors than would be expected in such a highly damped linear system.

Housner, J. M.↗

Annual report to the NASA Administrator by the Aerospace Safety Advisory Panel. Part 2: Space shuttle program. Section 2: Summary of information developed in the Panel's fact-finding activities

The management areas and the individual elements of the shuttle system were investigated. The basic management or design approach including the most obvious limits or hazards that are significant to crew safety was reviewed. Shuttle program elements that were studied included the orbiter, the space shuttle main engine, the external tank project, solid rocket boosters, and the launch and landing elements.

Source record↗

A document describing shuttle considerations for the design of large space structures

A Shuttle user guide document to aid designers and analysis associated with large space structures projects is described. The format and contents are a compromise designed to satisfy the needs of several levels of users. Special features include checklists and references to source documents as a convenience to very knowledgeable readers. In addition, general, introductory and explanatory text, and art work are included for the reader less familiar with shuttle systems. Also, there are a subject index, glossary, list of acronyms, and many cross references. Throughout the document, there are suggested implications or references to the importance of the included orbiter interfaces material as it pertains to designing and planning large space structures projects. The content of the document is outlined. Shuttle payload accommodations and constraints, connections for orbiter construction fixtures, packaging, and construction space eometry are addressed.

Roebuck, J. A., Jr.↗

Development of a window protection assembly for a shuttle experiment

A window environmental protection assembly developed for the shuttle infrared leeside temperature experiment is described. The assembly consists of a carbon phenolic composite window mount which contains two silicon windows, a fibrous environmental protection plug to protect the windows during launch operations and ascent heating, a release mechanism used to jettison the plug just prior to atmospheric entry, and two pin puller mechanisms which retain the plug. The plug is released from the window mount assemblies using pneumatic pin pullers and separation springs in the release mechanism. The assembly was designed and tested to withstand the severe mechanical and thermal environments which could be experienced at the top of the shuttle orbiter vertical stabilizer during the ascent, on-orbit, and entry periods of the shuttle trajectory.

Bradley, O. H., Jr.↗

Shuttle-based observations

Progress in science in relation to the space shuttle is reported. Several studies on the uses of the space shuttle and Spacelab are highlighted. A review of the activities of the Shuttle Spacelab Payloads Project Office are presented. The activities cover such fields as solar physics, astronomy with optical instruments, high energy astrophysics, atmospheric research and magnetospheric physics, and Earth observational studies.

Dubin, M.↗

The Shuttle Era

An overview of the Space Shuttle Program is presented. The missions of the space shuttle orbiters, the boosters and main engine, and experimental equipment are described. Crew and passenger accommodations are discussed as well as the shuttle management teams.

Source record↗

Space Shuttle cargo processing.

The spacecraft processing techniques to be used at the Kennedy Space Center for the assembly and check-out of Space Shuttle cargoes are discussed. The processing flow for vertically handled spacecraft, which are inserted into the Shuttle orbiter cargo bay while the orbiter is in the vertical position and often are attached to a separate solid booster stage, includes assembly into unified payloads in the Vertical Processing Facility, followed by Cargo Integration Test Equipment tests to ensure cargo bay compatibility, and transportation to the launch pad. Horizontally handled spacecraft such as Spacelab, which are inserted into the Orbiter cargo bay while it is in the Orbiter Processing Facility in the horizontal position, are assembled and checked out within the Operations and Checkout Building, where the CITE tests are performed and the Spacelab will be disassembled, and then transported to the Orbiter Processing Facility. It is pointed out that during the Space Shuttle era, when the number of spacecraft to be processed simultaneously at Kennedy will double or triple, all spacecraft processing facilities will be required to handle the workload.

Neilon, J. J.↗

The Shuttle and its importance to space medicine

The physiological effects of space flights on humans are reviewed, and the opportunities offered by frequent and repetitive Space Shuttle flights for space medical research are discussed. The most significant changes encountered in the vestibular, cardiopulmonary, musculoskeletal and hematopoietic systems during and after past space missions are indicated, and the time courses of the physiological shifts associated with space acclimatization and readaptation to a 1-g environment are summarized. Effects directly attributable to the absence of gravity, including postural changes and fluid shifts, are considered, and additional contributing factors to physiological changes imposed by the spacecraft operational environment are pointed out. Differences between the Space Shuttle missions and all previous missions in the areas of reentry profiles and varied crew composition are discussed, and results of experiments on the relative acceleration tolerances of men and women of different ages and the usefulness of the anti-g suit are presented. Directions for future research in space medicine available with the Shuttle are examined, with particular emphasis on the neurovestibular system cardiopulmonary dynamics, calcium metabolism, the erythropoietic system and the effects of space radiation.

Nicogossian, A.↗

A survey of load methodologies for shuttle orbiter payloads

Loads methods currently being used to design planetary spacecraft to be launched on the shuttle orbiter are summarized. Experiences gained from expendable launch vehicle payloads are used to develop methodologies for the space shuttle orbiter payloads. The objectives for the development of a new methodology for the shuttle payloads are to reduce the cost and schedule for the payload load analysis by decoupling the payload analysis from the launch vehicle to the maximum extent possible. Methods are described for payload member load estimation or obtaining upper bounds for dynamic loads, as well as load prediction or calculating actual transient member load time histories.

Chen, J. C.↗