Search NASA⌕ Search

SEARCH · Search NASA

Results for “Solid electrolyte interface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Hydrogen bonds enhanced composite polymer electrolyte for high-voltage cathode of solid-state lithium battery

Polymer electrolyte is one of the important components for developing advanced solid-state lithium batteries (SSLBs). However, the narrow electrochemical stability window restricts the practical application with high-voltage cathodes. In this study, a series of composite solid electrolytes (CSEs), possessing both wide electrochemical stability window (up to 5.0 V vs. Li + /Li) and high ionic conductivity (over 1.35×10 -3 S/cm at 25 °C), were reported by integrating SiO 2 nanoparticles into poly(vinyl ethylene carbonate) polymer electrolyte. The enhanced anti-oxidation performances are mainly caused and confirmed by the local intermolecular interactions of hydrogen bonds in CSE. Based on this CSE, the SSLBs with LiCoO 2 cathode present good cycle stability at high voltage, and the capacity retention with 4.5 V cut-off voltage is about 94% after 200 cycles. This work not only proves the importance of intermolecular interactions in CSE, but also provides an effective method for achieving high-energy SSLBs with enhanced interface compatibility between polymer electrolyte and highvoltage cathodes

25 ENERGY STORAGE↗

Tuning Bulk Redox and Altering Interfacial Reactivity in Highly Fluorinated Cation-Disordered Rocksalt Cathodes

Lithium-excess, cation-disordered rocksalt (DRX) materials have been subject to intense scrutiny and development in recent years as potential cathode materials for Li-ion batteries. Despite their compositional flexibility and high initial capacity, they suffer from poorly understood parasitic degradation reactions at the cathode-electrolyte interface. These interfacial degradation reactions deteriorate both the DRX material and electrolyte, ultimately leading to capacity fade and voltage hysteresis during cycling. In this work, differential electrochemical mass spectrometry (DEMS) and titration mass spectrometry are combined to quantify the extent of bulk redox and surface degradation reactions for a set of Mn 2+/4+ -based DRX oxyfluorides during initial cycling with a high-voltage charging cutoff (4.8 V vs Li/Li + ). Increasing the fluorine content from 7.5 to 33.75% is shown to diminish oxygen redox and suppresses high-voltage O 2 evolution from the DRX surface. Additionally, electrolyte degradation processes resulting in the formation of both gaseous species and electrolyte-soluble protic species are observed. Subsequently, DEMS is paired with a fluoride-scavenging additive to demonstrate that increasing fluorine content leads to increased dissolution of fluorine from the DRX material into the electrolyte. Finally, a suite of ex situ spectroscopy techniques (X-ray photoelectron spectroscopy, inductively coupled plasma optical emission spectroscopy, and solid-state nuclear magnetic resonance spectroscopy) are employed to study the change in DRX composition during charging, revealing the dissolution of manganese and fluorine from the DRX material at high voltages. Here this work provides insight into the degradation processes occurring at the DRX-electrolyte interface and points toward potential routes of interfacial stabilization.

25 ENERGY STORAGE↗

Eliminating chemo-mechanical degradation of lithium solid-state battery cathodes during >4.5 V cycling using amorphous Nb2O5 coatings

Abstract Lithium solid-state batteries offer improved safety and energy density. However, the limited stability of solid electrolytes (SEs), as well as irreversible structural and chemical changes in the cathode active material, can result in inferior electrochemical performance, particularly during high-voltage cycling (>4.3 V vs Li/Li + ). Therefore, new materials and strategies are needed to stabilize the cathode/SE interface and preserve the cathode material structure during high-voltage cycling. Here, we introduce a thin (~5 nm) conformal coating of amorphous Nb 2 O 5 on single-crystal LiNi 0.5 Mn 0.3 Co 0.2 O 2 cathode particles using rotary-bed atomic layer deposition (ALD). Full cells with Li 4 Ti 5 O 12 anodes and Nb 2 O 5 -coated cathodes demonstrate a higher initial Coulombic efficiency of 91.6% ± 0.5% compared to 82.2% ± 0.3% for the uncoated samples, along with improved rate capability (10x higher accessible capacity at 2C rate) and remarkable capacity retention during extended cycling (99.4% after 500 cycles at 4.7 V vs Li/Li + ). These improvements are associated with reduced cell polarization and interfacial impedance for the coated samples. Post-cycling electron microscopy analysis reveals that the Nb 2 O 5 coating remains intact and prevents the formation of spinel and rock-salt phases, which eliminates intra-particle cracking of the single-crystal cathode material. These findings demonstrate a potential pathway towards stable and high-performance solid-state batteries during high-voltage operation.

Science & Technology - Other Topics↗

Design of High-Voltage Stable Hybrid Electrolyte with an Ultrahigh Li Transference Number

Considering the high energy consumption during processing, and the low compliance and adhesion of ceramic electrolytes, the integration of polymer into ceramic electrolytes provides a way to mitigate the interfacial issues. However, the severe ion concentration gradient, low ionic conductivity, and instability toward Li metal and high-voltage cathodes become the major concerns in applying hybrid electrolytes. In this work, we report a single-ionconducting hybrid electrolyte (SIE-LLZO) with 64 wt % Li 7 La 3 Zr 2 O 12 (LLZO) particles embedded in a fluoroboron-centered Li-conductive polymer framework (LiBFSIE). The SIE-LLZO electrolyte exhibited a high Li transference number of 0.94 and electrochemical stability up to 5.6 V vs Li/Li + . Promising averaged Coulombic efficiencies of 99.97% and 99.91% were achieved in cells with LiNi 0.8 Co 0.15 Al 0.05 O 2 and LiNi 0.6 Mn 0.2 Co 0.2 O2 cathodes for 400 and 200 cycles, respectively. Finally, the Li-conducting pathway in the hybrid electrolyte was further investigated by a 6 Li-to- 7 Li isotope replacement method, indicating that Li transport mainly relies on the LLZO and interface between LiBFSIE and LLZO.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Alkali-metal batteries with a dendrite-free anode interfacing an organic liquid electrolyte

A rechargeable battery cell has an organic-liquid electrolyte contacting a dendrite free alkali-metal anode. The alkali-metal anode may be a liquid at the operating temperature that is immobilized by absorption into a porous membrane. The alkali-metal anode may be a solid that wets a porous-membrane separator, where the contact between the solid alkali-metal anode and the liquid electrolyte is at micropores or nanopores in the porous-membrane separator. The use of a dendrite-free solid lithium cell was demonstrated in a symmetric cell with a porous cellulose-based separator membrane. A K+-ion rechargeable cell was demonstrated with a liquid K—Na alloy anode immobilized in a porous carbon membrane using an organic-liquid electrolyte with a Celgard® or glass-fiber separator.

25 ENERGY STORAGE↗

Machine-Learning-Guided Insights into Solid-Electrolyte Interphase Conductivity: Are Amorphous Lithium Fluorophosphates the Key?

Despite decades of study, the identity of the dominant Li + -conducting phase within the inorganic SEI of Li-ion batteries remains unresolved. While the mosaic model describes LiF/Li 2 O/Li 2 CO 3 nanocrystallites within a disordered matrix, these crystalline phases inherently offer limited ionic conductivity. Growing evidence suggests that interfaces, grain boundaries, and amorphous phases may instead host the primary fast-ion pathways. Using diffusion-based generative structure prediction and machine-learning interatomic potentials (MLIPs), we investigate lithium difluorophosphate (LiPO 2 F 2 ), a key mixed-anion decomposition product of phosphorus- and fluorine-containing electrolytes. We identify a stable crystalline polymorph and demonstrate that the amorphous counterpart is conductive, with projected room-temperature σ ≈ 0.18 mS cm –1 and E a ≈ 0.40 eV. Here, this enhancement stems from structural disorder flattening the Li site-energy landscape and a low formation energy for Li-interstitial defects, which supplies additional mobile carriers. We propose amorphous mixed-anion Li-P-O-F phases as a promising conducting medium in the SEI, offering a specific target for engineering improved battery interfaces.

Zhong, Peichen [University of California, Berkeley↗

Structural effects of composition tuning in A-site disordered perovskite La0.5Li0.5−xMxTiO3 (M = Na, K) nanorods for fast interfacial transport for solid composite electrolyte design

Polymer-ceramic composite electrolytes (CPE) have emerged as promising replacements for currently used liquid organic electrolytes, which pose as safety hazards, in Li-ion batteries. Limits in conductivity enhancement in CPEs is often attributed to a high resistance for Li-ion transport along the interface due to the incompatibility of the polymer and ceramic phases. A clear understanding of the interfacial structure and how this impacts interfacial Li-ion transport is needed in order to efficiently design a CPE with optimal ionic conductivity. In this study, density functional theory (DFT) calculations, in conjunction with scanning transmission electron microscopy (STEM) and electron energy loss spectroscopy (EELS), are used to unveil the bulk and surface structure of La0.5Li0.5−xMxTiO3 (M = Na, K) (LMTO) nanorods, a newly-reported ceramic system with promising applications in CPEs, and the LMTO interactions with the poly(lithium sulfonyl (trifluoromethane sulfonyl)imide methacrylate) (p(MTFSILi)) polymerized ionic liquid. Substitution of lithium for sodium and potassium onto the A-site perovskite lattice is shown to increase the stability of the preferred pseudocubic perovskite phase because of their increased cation size which allows them to reduce the TiO6 octahedral rotations in the bulk and at the surface. STEM and EELS results show that LMTO nanorods with differing compositions have Ti-enriched (110)-oriented surfaces. Increased sodium and potassium compositions in LMTO is also shown using the DFT calculations to weaken the binding of the lithium atom to the MTFSI unit when LiMTFSI is adsorbed to the LMTO surface. This weakening of lithium binding to the polymer at the LMTO interface indicates that the lithium mobility is increased, correlating to an increase in interfacial Li-ion transport. Overall, this work provides insights into how to tune the interfacial interactions between the polymer (p(MTFSI)) and ceramic (LMTO) for optimal CPE design.

Shepard, Lauren B [Pennsylvania State University, ↗

Improved Durability of SOEC Stacks for High Temperature Electrolysis

High temperature steam electrolysis is a promising technology for efficient and sustainable large-scale hydrogen production. Solid oxide electrolysis cells (SOECs) are able to utilize high temperature heat and electric power from advanced high-temperature nuclear reactors or renewable sources to generate carbon-free hydrogen at large scale. However, long term durability of SOECs needs to be improved significantly before commercialization of this technology can be realized. A degradation rate of 1%/khr or lower is proposed as a threshold value for commercialization of this technology. Solid oxide electrolysis stack tests have been conducted at Idaho National Laboratory to demonstrate recent improvements in long-term durability of SOECs. Electrolyte-supported and electrode-supported SOEC stacks were provided by Ceramatec Inc. and Materials and Systems Research Inc. (MSRI), respectively, for these tests. Long-term durability tests were generally operated for a duration of 1000 hours or more. Stack tests based on technologies developed at Ceramatec and MSRI have shown significant improvement in durability in the electrolysis mode. Long-term degradation rates of 3.2%/khr and 4.6%/khr were observed for MSRI and Ceramatec stacks, espectively. One recent Ceramatec stack even showed negative degradation (performance improvement) over 1900 hours of operation. Optimization of electrode materials, interconnect coatings, and electrolyte-electrode interface microstructures contribute to better durability of SOEC stacks.

08 HYDROGEN↗

The Study of the Binder Poly(acrylic acid) and Its Role in Concomitant Solid–Electrolyte Interphase Formation on Si Anodes

In this work we use neutron reflectometry to study how the polymeric binder, poly(acrylic acid) (PAA), affects the in situ formation and chemical composition of the solid–electrolyte interphase (SEI) formation on a silicon anode at various states of charge. The reflectivity is correlated with electrochemical quartz crystal microbalance to better understand the viscoelastic effects of the polymer during cycling. The use of model thin films allows for a well-controlled interface between the amorphous Si surface and the PAA layer. If the PAA perfectly coats the Si surface and standard processing conditions are used, the binder will prevent the lithiation of the anode. The PAA suppresses the growth of a new layer formed at early states of discharge (open circuit voltage to 0.8 V vs Li/Li+), protecting the surface of the anode. At 0.15 V, the SEI layer underneath the PAA changes in chemical composition as indicated by an increase in the scattering length density and thickness as the layer incorporates components from the electrolyte, most likely the salt. At lithiated and delithiated states, the SEI layer changes in chemical composition and grows in thickness with delithiation and shrinks during lithiation.

36 MATERIALS SCIENCE↗

Increasing the Pressure‐Free Stripping Capacity of the Lithium Metal Anode in Solid‐State‐Batteries by Carbon Nanotubes

Abstract Lithium metal is the key anode material for solid‐state‐batteries as its successful implementation will drastically increase their energy and power densities. However, anode contact loss during stripping leads to dendrites upon plating and subsequent cell failure. Design strategies to mitigate these issues are crucial to enable the use of lithium metal anodes. This paper reports the dissolution kinetics of composite anodes made of lithium metal and carbon nanotubes (CNTs) with a garnet‐type solid electrolyte (SE). In addition to an enhancement of the effective diffusion within the anode, its dissolution is fundamentally changed from being 2D to 3D. By maintaining contact with the SE, the CNTs facilitate lithium transport to the interface, which yields more than 20 mAh cm −2 discharge capacity at 100 µ A cm −2 without the application of external stack pressure ( > 1 MPa). Conclusions drawn from electrochemical data on the anode microstructure are validated using cryo‐focused‐ion‐beam scanning electron microscopy and correlated with the mechanical properties. Micro‐indentation, acoustic analysis, and stress–strain testing show that mechanical properties of the anode, like yield strength and hardness, are adjustable. Overall, it is shown that the mechanical and electrochemical properties of Li–CNT composite electrodes can be tailored to suit the requirements of a practical cell.

Fuchs, Till↗

Solid Electrolyte Bimodal Grain Structures for Improved Cycling Performance

Here, the application of solid-state electrolytes in Li batteries is hampered by the occurrence of Li-dendrite-caused short circuits. To avoid cell failure, the electrolytes can only be stressed with rather low current densities, severely restricting their performance. As grain size and pore distributions significantly affect dendrite growth in ceramic electrolytes such as Li 7 La 3 Zr 2 O 12 and its variants; here, a “detour and buffer” strategy to bring the superiority of both coarse and fine grains into play, is proposed. To validate the mechanism, a coarse/fine bimodal grain microstructure is obtained by seeding unpulverized large particles in the green body. The rearrangement of coarse grains and fine pores is fine-tuned by changing the ratio of pulverized and unpulverized powders. The optimized bimodal microstructure, obtained when the two powders are equally mixed, allows, without extra interface decoration, cycling for over 2000 h as the current density is increased from 1.0 mA·cm -2 , and gradually, up to 2.0 mA·cm -2 . The “detour and buffer” effects are confirmed from postmortem analysis. The complex grain boundaries formed by fine grains discourage the direct infiltration of Li. Simultaneously, the coarse grains further increase the tortuosity of the Li path. This study sheds light on the microstructure optimization for the polycrystalline solid-state electrolytes.

25 ENERGY STORAGE↗

Visualizing Lithium Dendrite Formation within Solid-State Electrolytes

Solid-state electrolyte (SSE) is promising for application in allsolid-state lithium metal batteries because of its reliable safety and longevity. The failure of SSE to suppress dendrite formation of Li metal anodes has been conventionally explained by uneven Li deposition at Li/SSE interfaces and its subsequent dendritic growth. While Li deposition within SSE has been recently proposed as another key cause for SSE failure, little is known regarding the Li growth details inside the SSE itself. In this work, we performed in situ microscopic observation of Li deposition inside the SSE and obtained visualized evidence regarding the dynamic process of Li dendrite formation and growth. Here, Li is seen to directly nucleate and propagate within the SSE, leading to its structural cracking. Such behavior should be caused by the presence of P- and S-based crystalline defects in Li 3 PS 4 SSE, which is consistent with the cryo-transmission electron microscopy observations and theoretical calculations. This observation provides important insights into the growth mechanisms of Li dendrites within a working lithium battery.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Designing carbon wetting layers with inorganic salts as additives for enhanced adhesion and molten sodium wettability in electrochemical application

ß” alumina solid-state electrolyte (BASE) is considered one of the most promising materials for sodium batteries due to its high ionic conductivity and exceptional stability with molten sodium. However, at lower operating temperatures, the poor physical contact at the liquid-solid interface between molten sodium and BASE results in high interfacial resistance. In this study, we explore the optimization of carbon wetting layers with various salt additives to enhance adhesion and improve molten sodium wettability. Using a spray-coating method, carbon layers incorporating sodium hexametaphosphate (Na6(PO3)6, SHMP) as an additive demonstrate superior adhesion, mechanical stability, and enhanced wettability with molten sodium. Scanning Electron Microscopy (SEM) analysis reveals that SHMP preserves the porous carbon network required for efficient sodium transport while minimizing structural defects such as cracks and voids. Electrochemical testing using Na symmetric cells confirms that SHMP-modified layers significantly reduce interfacial resistance and overpotential, outperforming No salts counterparts. These findings highlight that the strategic incorporation of suitable additives, such as SHMP, in the design of microscale carbon layers could significantly enhance the performance of molten sodium batteries at lower operating temperatures.

Han, Henry H.↗

Multifunctional Coatings on Sulfide‐Based Solid Electrolyte Powders with Enhanced Processability, Stability, and Performance for Solid‐State Batteries

Abstract Sulfide‐based solid‐state electrolytes (SSEs) exhibit many tantalizing properties including high ionic conductivity and favorable mechanical properties for next‐generation solid‐state batteries. Widespread adoption of these materials is hindered by their intrinsic instability under ambient conditions, which makes them difficult to process at scale, and instability at the Li||SSE and cathode||SSE interfaces, which limits cell performance and lifetime. Atomic layer deposition is leveraged to grow thin Al 2 O 3 coatings on Li 6 PS 5 Cl powders to address both issues simultaneously. These coatings can be directly grown onto Li 6 PS 5 Cl particles with negligible chemical modification of the underlying material and enable exposure of powders to pure and H 2 O‐saturated oxygen environments for ≥4 h with minimal reactivity, compared with significant degradation of the uncoated powder. Pellets fabricated from coated powders exhibit ionic conductivities up to 2× higher than those made from uncoated material, with a simultaneous decrease in electronic conductivity and significant suppression of chemical reactivity at the Li‐SSE interface. These benefits result in significantly improved room temperature cycle life at high capacity and current density. It is hypothesized that this enhanced performance derives from improved intergranular properties and improved Li metal adhesion. This work points to a completely new framework for designing active, stable, and scalable materials for next‐generation solid‐state batteries.

36 MATERIALS SCIENCE↗

Electrochemical and Interfacial Behavior of All Solid State Batteries Using Li10SnP2S12 Solid Electrolyte

Thio-Lithium Superionic Conductor (Thio-LISICON) Li10GeP2S12 equivalent Li10SnP2S12 (LSPS) is comparable in ionic conductivity yet with a lower cost as an electrolyte for all solid-state batteries (ASSBs). ASSBs with LSPS solid electrolyte (SE), lithium-indium alloy anode, and LiCoO2 (LCO) cathode were successfully fabricated and their electrochemical performance at 60 °C was examined. Atomic layer deposition of Li3NbO4 on LCO was conducted to improve the interfacial stability. The Li3NbO4 coating significantly improves the cycle stability of the ASSB, which retains about 85% of the initial capacity after 70 cycles at a current density of 0.13 mA/cm2, while the ASSB with uncoated LCO retains ~ 60% of the initial capacity after 70 cycles. Electrochemical impedance spectroscopy tests indicate a rapid growth of charge transfer resistance upon cycling for the cell with the uncoated LCO, primarily due to the surface instability and build-up of a space charge layer between LSPS and LCO. However, the ASSBs with Li3NbO4 coated LCO show a more stable interface with a negligible impedance increase upon cycling, attributable to the buffering and passivating roles of the Li3NbO4 coating. The interfacial microstructure was analyzed to elucidate at the underlying reasons for the impedance increase and the pivotal role of the Li3NbO4 coating. Our study indicates that the surface coating significantly improves the cycle stability of the ASSBs with LSPS as the electrolyte, mostly due to an improvement of the charge transfer mechanism. The coating reduced the interphase thickness and the interfacial resistance to about a third of the uncoated one after 10 cycles.

Vinado, Carolina↗

Fluoroethylene Carbonate Induces Ordered Electrolyte Interface on Silicon and Sapphire Surfaces as Revealed by Sum Frequency Generation Vibrational Spectroscopy and X-ray Reflectivity

Here, the cyclability of silicon anodes in lithium ion batteries (LIBs) is affected by the reduction of the electrolyte on the anode surface to produce a coating layer termed the solid electrolyte interphase (SEI). One of the key steps for a major improvement of LIBs is unraveling the SEI’s structure-related diffusion properties as charge and discharge rates of LIBs are diffusion-limited. To this end, we have combined two surface sensitive techniques, sum frequency generation (SFG) vibrational spectroscopy, and X-ray reflectivity (XRR), to explore the first monolayer and to probe the first several layers of electrolyte, respectively, for solutions consisting of 1 M lithium perchlorate (LiClO 4 ) salt dissolved in ethylene carbonate (EC) or fluoroethylene carbonate (FEC) and their mixtures (EC/FEC 7:3 and 1:1 wt %) on silicon and sapphire surfaces. Our results suggest that the addition of FEC to EC solution causes the first monolayer to rearrange itself more perpendicular to the anode surface, while subsequent layers are less affected and tend to maintain their, on average, surface-parallel arrangements. This fundamental understanding of the near-surface orientation of the electrolyte molecules can aid operational strategies for designing high-performance LIBs.

36 MATERIALS SCIENCE↗

A Bi-Layer Dense/Porous Solid Electrolyte Interphase for Enhanced Lithium-Metal Stability

Due to its high theoretical capacity and low electrochemical potential, lithium metal is a highly investigated anode for next-generation high-energy batteries. However, the unstable chemical and topographical heterogeneous surface of lithium gives rise to safety and efficiency concerns that prevent it from being utilized in practical applications. Exposure to electrolyte leads to non-uniform, mixed organic-inorganic solid-electrolyte interphase (SEI) formation, starting a cascading to non-uniform flux distribution, consumption of active materials, and dendrite growth. The SEI is the key feature that will lead to harnessing the capabilities possible with lithium metal. In this work, the formation of a closed-host bi-layer solid electrolyte interphase (SEI) improves the stability of lithium anode. This is successfully realized by forming an interconnected porous LiF-rich artificial SEI in contact with Li metal, and a dense, stable in-situ formed upper layer SEI. The porous layer increases the number of Li/LiF interfaces, which reduces local volume fluctuations and improves Li+ diffusion along these interfaces. Additionally, the tortuous porous structure guides uniform Li+ flux distribution and mechanically suppresses dendrite propagation. The dense upper layer of the SEI accomplishes a closed-host design through reaction with LiNO3 additive and prevents continuous consumption of active materials seen without the additive included in the electrolyte. The duality of a dense top layer with porous bottom layer led to extended cycle life and improved rate performance, evidenced with symmetric cell testing, as well as full cell testing paired with sulfur and LiFePO4 (LFP) cathodes. This work is a good example of a rational design of the SEI, based on comprehensive consideration of various critical factors to improve Li-metal anode stability, and highlights a new pathway to improve cycling and rate performances of Li metal batteries.

25 ENERGY STORAGE↗