Search NASA⌕ Search

SEARCH · Search NASA

Results for “Struts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Behavior of aircraft antiskid braking systems on dry and wet runway surfaces: Hydromechanically controlled system

The investigation utilized one main gear wheel, brake, and tire assembly of a McDonnell Douglas DC-9 series 10 airplane. The landing-gear strut was replaced by a dynamometer. During maximum braking, average braking behavior indexes based upon brake pressure, brake torque, and drag-force friction coefficient developed by the antiskid system were generally higher on dry surfaces than on wet surfaces. The three braking behavior indexes gave similar results but should not be used interchangeably as a measure of the braking of this antiskid sytem. During the transition from a dry to a flooded surface under heavy braking, the wheel entered into a deep skid but the antiskid system reacted quickly by reducing brake pressure and performed normally during the remainder of the run on the flooded surface. The brake-pressure recovery following transition from a flooded to a dry surface was shown to be a function of the antiskid modulating orifice.

Tanner, J. A.↗

Organic Rankine cycle receiver development

The selected receiver concept is a direct-heated, once-through, monotube boiler operated at supercritical pressure. The cavity is formed by a cylindrical copper shell and backwall, with stainless steel tubing brazed to the outside surface. This core is surrounded by lightweight refractory insulation, load-bearing struts, and an outer case. The aperture plate is made of copper to provide long life by conduction and reradiation of heat away from the aperture lip. The receiver thermal efficiency is estimated to be 97 percent at rated conditions (energy transferred to toluene divided by energy incident on aperture opening). Development of the core manufacturing and corrosion protection methods is complete.

Haskins, H. J.↗

Turbomachinery noise studies of the AiResearch QCGAT engine with inflow control

The AiResearch Quiet Clean General Aviation Turbofan engine was tested on an outdoor test stand to compare the acoustic performance of two inflow control devices (ICD's) of similar design, and three inlet lips of different external shape. Only small performance differences were found. Far-field directivity patterns calculated by applicable existing analyses were compared with the measured tone and broadband patterns. For some of these comparisons, tests were made with an ICD to reduce rotor/inflow disturbance interaction noise, or with the acoustic suppression panels in the inlet or bypass duct covered with aluminum tape to determine hard wall acoustic performance. The comparisons showed that the analytical expressions used predict many directivity pattern features and trends, but can deviate in shape from the measured patterns under certain engine operating conditions. Some patterns showed lobes from modes attributable to rotor/engine strut interaction sources.

Mcardle, J. G.↗

Recent advances in structural technology for large deployable and erectable spacecraft

Ultra-low mass deployable and erectable truss structure designs for spacecraft are identified using computerized structural sizing techniques. Extremely slender strut proportions are shown to characterize minimum mass spacecraft which are designed for Shuttle transport to orbit. Analytical results are presented which demonstrate discrete element effects using a recently developed buckling theory for periodic lattice type structures. An analysis of fabrication imperfection effects on the surface accuracy of four different antenna reflector structures is summarized. This study shows the tetrahedral truss to have the greatest potential of the structures examined for application to accurate or large reflectors. A deployable module which can be efficiently transported is identified and shown to have significant potential for application to future antenna requirements. Recent investigations of erectable structure assembly are reviewed. Initial experiments simulating astronaut assembly by extra-vehicular activity (EVA) show that a pair of astronauts can achieve assembly times of 2-5 min/strut. Studies indicate that an automated assembler can achieve times of less than 1 min/strut on an around-the-clock basis.

Bush, H. G.↗

Unsteady fan blade pressure and acoustic radiation from a JT15D-1 turbofan engine at simulated forward speed

Tests have been conducted on a JT15D-1 turbofan engine both statically and at simulated forward speed in the Ames 12 x 24 Meter Wind Tunnel. Both far-field acoustic data and unsteady pressure data from transducers mounted on the fan blades were acquired. Results showed a sound power reduction of about 10 dB in the far-field acoustic levels with simulated forward speed over those measured without forward speed. Blade mounted transducer results showed rotor-turbulence interaction dominated the noise field at very low speeds while an interaction between the rotor and internal struts dominated at higher speeds. Results are presented to show the effects of varying engine rpm, changing the angle-of-attack of the engine inlet to tunnel flow and mounting an aircraft wing to simulate an installation condition on an actual aircraft.

Preisser, J. S.↗

Deployable and erectable concepts for large spacecraft

The structural proportions of minimum-mass tetrahedral truss platforms designed for low earth and geosynchronous orbit are determined by means of computerized sizing techniques, taking into account multiple design requirements and constraints. Strut dimensions characterizing minimum mass designs are found to be significantly more slender than those used for conventional structural applications. It is also shown that the number of shuttle flights required by deployable trusses becomes excessive above certain critical stiffness values, and that an automated assembler can achieve rates of 1 min/strut, by comparison with 2-5 min/strut for two astronauts using manual labor.

Bush, H. G.↗

Stray radiation and the Infrared Astronomical Satellite /IRAS/ telescope

Stray light control is a major consideration in the design of infrared cryogenically cooled telescopes such as the Infrared Astronomical Satellite (IRAS). The basic design of the baffle system, and the placement, shape, and coating of the secondary support struts for the telescope subsystem are described. The intent of this paper is to highlight the stray light problems encountered while designing the system, and to illustrate how computer analysis can be a useful design aid. Scattering measurements of the primary mirror, and a full system level scatter measurement are presented. Comparisons of predicted performance with the measured results are also presented.

Noll, R. J.↗

Aerodynamic and acoustic behavior of a YF-12 inlet at static conditions

An aeroacoustic test program was performed with a YF-12 aircraft at ground static conditions. The objective was to collect acoustic and aerodynamic data that could determine the cause of YF-12 inlet noise suppression observed earlier. The results showed that the far-field noise level was lower with the YF-12 inlet than with a bellmouth inlet at engine speeds above 5500 rpm. The differences were about 5 PNdB to 11 PNdB, depending on YF-12 inlet configuration and on engine speed. Measurements showed that YF-12 inlet noise suppression was not caused by flow choking. The spike support struts were probably responsible, as in that region the spectral peak near the blade passing frequency disappeared between 6000 and 6600 rpm, and multiple pure tones were greatly reduced.

Bangert, L. H.↗

Improvements in Heat Transfer for Anti-Icing of Gas-Heated Airfoils with Internal Fins and Partitions

The effect of modifying the gas passage of hollow metal airfoils by the additIon of internal fins and partitions was experimentally investigated and comparisons were made among a basic unfinned airfoil section and two airfoil designs having metal fins attached at the leading edge of the internal gas passage. An analysis considering the effects of heat conduction in the airfoil metal was made to determine the internal modification effectiveness that may be obtained in gas-heated components, such as turbojet-inlet guide vanes, support struts, hollow propeller blades, arid. thin wings. Over a wide range of heated-gas flow and tunnel-air velocity, the increase In surface-heating rates with internal finning was marked (up to 3.5 times), with the greatest increase occurring at the leading edge where anti-icing heat requirements are most critical. Variations in the amount and the location of internal finning and. partitioning provided. control over the local rates of surface heat transfer and permitted efficient anti-icing utilization of the gas-stream heat content.

Gray, Vernon H.↗

Feasibility study for long lifetime helium dewar

A feasible concept for a launchable three year lifetime helium dewar was investigted. Current helium dewar designs were examined to see where the largest potential reductions in parasitic heat loads can be made. The study was also devoted to examining support concepts. The support concept chosen, a passive orbital disconnect strut (PODS), has an orbital support conductance that is lower by more than an order of magnitude over current tension band supports. This lower support conductance cuts the total dewar weight in half for the same three year life time requirements. Effort was also concentrated on efficient wire feed through designs and vapor cooling of the multilayer insulation, supports, wire feed throughs and plumbing penetrations. A single stage helium dewar vs. dual stage dewars with a guard cryogen of nitrogen or neon was examined. The single stage dewar concept was selected. Different support concepts were analyzed from which the PODS support concepts was chosen. A preliminary design of the dewar was thermally and structurally analyzed and laid out including system weights, thermal performance and performance sensitivities.

Parmley, R. T.↗

Composite structural materials

Physical properties of fiber reinforced composites; structural concepts and analysis; manufacturing; reliability; and life prediction are subjects of research conducted to determine the long term integrity of composite aircraft structures under conditions pertinent to service use. Progress is reported in (1) characterizing homogeneity in composite materials; (2) developing methods for analyzing composite materials; (3) studying fatigue in composite materials; (4) determining the temperature and moisture effects on the mechanical properties of laminates; (5) numerically analyzing moisture effects; (6) numerically analyzing the micromechanics of composite fracture; (7) constructing the 727 elevator attachment rib; (8) developing the L-1011 engine drag strut (CAPCOMP 2 program); (9) analyzing mechanical joints in composites; (10) developing computer software; and (11) processing science and technology, with emphasis on the sailplane project.

Ansell, G. S.↗

Fluctuating pressures on fan blades of a turbofan engine: Static and wind-tunnel investigations

To investigate the fan noise generated from turbofan engines, miniature pressure transducers were used to measure the fluctuating pressure on the fan blades of a JT15D engine. Tests were conducted with the engine operating on an outdoor test stand and in a wind tunnel. It was found that a potential flow interaction between the fan blades and six, large support struts in the bypass duct is a dominant noise source in the JT15D engine. Effects of varying fan speed and the forward speed on the blade pressure are also presented.

Schoenster, J. A.↗

Computer modeling of fan-exit-splitter spacing effects on F100 response to distortion

The distortion response of the F100(3) engine was effected by the fan exit splitter configuration. The sensitivity for a proximate splitter fan is calculated to be slightly greater than a remote splitter configuration with identical airfoils. Predicted response was based upon a multiple segment parallel compressor Model modified to include a bypass ratio representation that effects the performance characteristics of the last rotor and intermediate case struts. The predicted distortion response required an accurate definition of row pre- and post-stall undistorted operation.

Shaw, M.↗

Energy efficient engine: Turbine transition duct model technology report

The Low-Pressure Turbine Transition Duct Model Technology Program was directed toward substantiating the aerodynamic definition of a turbine transition duct for the Energy Efficient Engine. This effort was successful in demonstrating an aerodynamically viable compact duct geometry and the performance benefits associated with a low camber low-pressure turbine inlet guide vane. The transition duct design for the flight propulsion system was tested and the pressure loss goal of 0.7 percent was verified. Also, strut fairing pressure distributions, as well as wall pressure coefficients, were in close agreement with analytical predictions. Duct modifications for the integrated core/low spool were also evaluated. The total pressure loss was 1.59 percent. Although the increase in exit area in this design produced higher wall loadings, reflecting a more aggressive aerodynamic design, pressure profiles showed no evidence of flow separation. Overall, the results acquired have provided pertinent design and diagnostic information for the design of a turbine transition duct for both the flight propulsion system and the integrated core/low spool.

Leach, K.↗

STOL capability impact on advanced tactical aircraft design

The design and technical issues affecting supersonic STOL development as an airbase attack fighter are discussed. An Air Force study has indicated that, from a weight and cost standpoint, the preferred directions will include two-dimensional nozzles with vectoring and thrust reversing capability. Take-off and landing requirements would determine other design features, and the use of a jump strut to enable landing maneuvers to be made at pitch angles which would normally drag the tail is detailed. The addition of a tip-mounted reaction control system is foreseen as necessary for roll control at the low aerodynamic speeds of STOL landing. A severe 700 ft landing distance design is outlined, and includes a lifting engine with bleed-air features to feed the reaction control system.

Krepski, R. E.↗

Space Shuttle flight results

System function aspects of the first Space Shuttle mission are assessed. Almost 90 mission anomalies have been identified by a mission evaluation team, which were variously attributed to instrumentation sensor failures, improper operation, or design deficiencies. The two most significant problems encountered were Solid Rocket Booster ignition wave overpressure, which exceeded maximum expected pressure by a factor of 2:1 over most of the Orbiter and 5:1 at a sensor location on the aft bulkhead, near the engines, and an inoperative tumble valve, which would normally have imparted to the Space Shuttle External Tank a tumbling motion, after Tank separation, that insures disintegration of the large structure during reentry. The first problem has been solved by strengthening six support struts, and the second by ensuring that the tumble valve is moisture-free.

Mccarty, B. J.↗

Free-jet acoustic investigation of high-radius-ratio coannular plug nozzles. Comprehensive data report, volume 1

Six coannular plug nozzle configurations having inverted velocity and temperature profiles, and a baseline convergent conical nozzle were tested for simulated flight acoustic evaluation in General Electric's Anechoic Free-Jet Acoustic Facility. The nozzles were tested over a range of test conditions that are typical of a Variable Cycle Engine for application to advanced high speed aircraft. The outer stream radius ratio for most of the configurations was 0.853, and the inner-stream-outer-stream area ratio was tested in the range of 0.54. Other variables investigated were the influence of bypass struts, a simple noncontoured convergent-divergent outer stream nozzle for forward quadrant shock noise control, and the effects of varying outer stream radius and inner-stream-to-outer-stream velocity ratios on the flight noise signatures of the nozzles. It was found that in simulated flight, the high-radius-ratio coannular plug nozzles maintain their jet noise and shock noise reduction features previously observed in static testing. The presence of nozzle bypass structs will not significantly effect the acoustic noise reduction features of a General Electric-type nozzle design. A unique coannular plug nozzle flight acoustic spectral prediction method was identified and found to predict the measured results quite well. Special laser velocimeter and acoustic measurements were performed which have given new insight into the jet and shock noise reduction mechanisms of coannular plug nozzles with regard to identifying further beneficial research efforts.

Knott, P. R.↗

Unsteady environments and responses of the shuttle combined loads orbiter test

Both separate and combined wind tunnel and vibration shaker tests were conducted on two structural panels representative of the Shuttle orbiter in the NASA LaRC 8-foot transonic pressure tunnel (TPT) to determine the effects of combined loads on the thermal protection system (TPS). The primary objective of this test was to provide a combined full-scale load environment and realistic time history of the dynamic pressures, Mach numbers (through transonic), and dynamic structural responses of these panels. The panels were selected from orbiter locations where interactive load sources such as aerodynamic shock waves, turbulent boundary layers, strut-induced vorticity, and substrate deformation combined to provide high bonding loads between the TPS and the orbiter structure. The test panels for this program were highly instrumented with static and dynamic pressure gages, accelerometers, deflectometers, strain gages, Schileren and high-speed photography, and special instrumentation necessary to determine TPS/structure interface loads and tile motions. Two test specimens of each orbiter panel were utilized. Both were high-fidelity representations of the selected orbiter location. The first panel (calibration panel) for each test was utilized to calibrate the tunnel and shaker system as well as provide a data-gathering source for applied static and dynamic loads. The second panel (test panel) for each test was subjected to flight time exposures only so that TPS characteristics as a function of flight mission exposure could be determined. These tests were the last in a series that was suce6ssfully completed and necessary to certify the TPS prior to the first launching of the Shuttle.

P. H. Schuetz↗