SEARCH · Search NASA

Results for “WINGS - SWEEPBACK”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

All sources NASA NTRS DOE OSTI

NASA NTRS1988

Evaluation of a three-dimensional empirically derived wing at supersonic speeds

A novel wing design concept is introduced which takes advantage of the existence of conical flow at supersonic speeds. The present wing design concept is to create a near conical wing geometry by redistributing airfoils in a spanwise direction. In addition, a set of graphs which review the supersonic aerodynamics of delta wings have been employed to select a design wing sweep and Mach number. An iteration through the wing design logic resulted in the selection of a 65 deg swept delta wing and a design Mach number of 1.62. Theoretical analysis was performed with a nonlinear full-potential analysis method to assess the merits of the wing design approach. The analysis showed large reductions in drag due to lift compared to delta wings configured with traditional thickness and airfoil distributions.

Wood, Richard M.↗

NASA NTRS1990

The aerodynamic design of the oblique flying wing supersonic transport

The aerodynamic design of a supersonic oblique flying wing is strongly influenced by the requirement that passengers must be accommodated inside the wing. It was revealed that thick oblique wings of very high sweep angle can be efficient at supersonic speeds when transonic normal Mach numbers are allowed on the upper surface of the wing. The goals were motivated by the ability to design a maximum thickness, minimum size oblique flying wing. A 2-D Navier-Stokes solver was used to design airfoils up to 16 percent thickness with specified lift, drag and pitching moment. A new method was developed to calculate the required pressure distribution on the wing based on the airfoil loading, normal Mach number distribution and theoretical knowledge of the minimum drag of oblique configurations at supersonic speeds. The wing mean surface for this pressure distribution was calculated using an inverse potential flow solver. The lift to drag ratio of this wing was significantly higher than that of a comparable delta wing for cruise speeds up to Mach 2.

Vandervelden, Alexander J. M.↗

NASA NTRS1990

Self-induced roll oscillations of low-aspect-ratio rectangular wings

Experimental investigation of small aspect ratio rectangular wings mounted on a free-to-roll sting balance indicated that self-induced roll oscillations are possible when the aspect ratio of such wings is less than 0.5. The oscillations are probably driven by the periodic changes in the location and strength of the side edge vortices, as it has been shown for the 'wing rock' motion of delta wings, where similar changes in the leading edge vortex strength and position cause the roll oscillations. During the roll oscillation cycle the roll angle, normal force, and the side force were recorded and presented for three wings with aspect ratios of 0.25, 0.35, and 0.47. This data indicates that the lift loss during roll oscillations of rectangular wings is less than what was measured for similar delta wings. Also, the flow field of such slender rectangular wings at high angles of attack is more complicated due to the additional leading edge vortex, when compared with the flow field over slender delta wings.

Levin, Daniel↗

NASA NTRS1991

Nonlinear Aerodynamics and the Design of Wing Tips

The analysis and design of wing tips for fixed wing and rotary wing aircraft still remains part art, part science. Although the design of airfoil sections and basic planform geometry is well developed, the tip regions require more detailed consideration. This is important because of the strong impact of wing tip flow on wing drag; although the tip region constitutes a small portion of the wing, its effect on the drag can be significant. The induced drag of a wing is, for a given lift and speed, inversely proportional to the square of the wing span. Concepts are proposed as a means of reducing drag. Modern computational methods provide a tool for studying these issues in greater detail. The purpose of the current research program is to improve the understanding of the fundamental issues involved in the design of wing tips and to develop the range of computational and experimental tools needed for further study of these ideas.

Kroo, Ilan↗

NASA NTRS1990

Static aeroelastic analysis of composite wing

A static aeroelastic analysis capability that can predict aerodynamic loads for the deformed shape of the composite wing has been developed. The finite element method (FEM) was used for composite plate structural analysis, and the linear vortex lattice method (VLM) was used for steady aerodynamic analysis. The final deformed shape of the wing due to applied forces is determined by iterative manner using FEM and VLM. FEM and VLM analysis are related by a surface spline interpolation procedure. The wing with Gr/Ep composite material has been investigated to see the wing deformation effect. Aerodynamic load change due to wing flexibility has been investigated. Also, the effect of fiber orientation and sweep angle on the deformation pattern and aerodynamic coefficients are examined. For a certain fiber orientation, the deflection and aerodynamic loading of the composite wing is very much reduced. The swept forward wing has more significant effect of wing flexibility on aerodynamic coefficient than the swept back wing does.

Lee, IN↗

NASA NTRS1952

Comparison between prediction and experiment for all-movable wing and body combinations at supersonic speeds : lift, pitching moment, and hinge moment

A simple method is presented for estimating lift, pitching-moment, and hinge-moment characteristics of all-movable wings in the presence of a body as well as the characteristics of wing-body combinations employing such wings. In general, good agreement between the method and experiment was obtained for the lift and pitching moment of the entire wing-body combination and for the lift of the wing in the presence of the body. The method is valid for moderate angles of attack, wing deflection angles, and width of gap between wing and body. The method of estimating hinge moment was not considered sufficiently accurate for triangular all-movable wings. An alternate procedure is proposed based on the experimental moment characteristics of the wing alone. Further theoretical and experimental work is required to substantiate fully the proposed procedure.

Nielsen, Jack N↗

NASA NTRS1928

Pressure Distribution Tests on PW-9 Wing Models Showing Effects of Biplane Interference

In this report tests are described in which the distribution of pressures over models of the wings of the PW-9 Airplane was investigated. The wing models were tested individually and in the biplane combination. The investigation was conducted in the atmospheric wind tunnel of the National Advisory Committee for Aeronautics. It is concluded in this paper that the effect of biplane interference on the pressures on the wings is practically confined to the lower surface of the upper wing and the upper surface of the lower wing; that the overhanging portion of the upper wing is not greatly affected by the presence of the lower wing; and that a slight washing at the center section of the upper wing satisfactorily compensates for a reduced chord at this section (providing the airfoil section is not mutilated) and prevents a large reduction in the normal force over this portion of the wing.

Fairbanks, A J↗

NASA NTRS1954

Determination of mean camber surfaces for wings having uniform chordwise loading and arbitrary spanwise loading in subsonic flow

The field of a uniformly loaded wing in subsonic flow is discussed in terms of the acceleration potential. It is shown that, for the design of such wings, the slope of the mean camber surface at any point can be determined by a line integration around the wing boundary. By an additional line integration around the wing boundary, this method is extended to include the case where the local section lift coefficient varies with spanwise location (the chordwise loading at every section still remaining uniform). For the uniformly loaded wing of polygonal plan form, the integrations necessary to determine the local slope of the surface and the further integration of the slopes to determine the ordinate can be done analytically. An outline of these integrations and the resulting formulas are included. Calculated results are given for a sweptback wing with uniform chordwise loading and a highly tapered spanwise loading, a uniformly loaded delta wing, a uniformly loaded sweptback wing, and the same sweptback wing with uniform chordwise loading but elliptical span load distribution.

Katzoff, S↗

NASA NTRS1960

Aerodynamic Characteristics at Mach Number 2.05 of a Series of Highly Swept Arrow Wings Employing Various Degrees of Twist and Camber

A series of arrow wings employing various degrees of twist and camber were tested in the Langley 4- by 4-foot supersonic pressure tunnel. Aerodynamic forces and moments in pitch were measured at a Mach number of 2.05 and at a Reynolds number of 4.4 x 10(exp 6) based on the mean aerodynamic chord. Three of the wings, having a leading-edge sweep angle of 70 deg. and an aspect ratio of 2.24, were designed to produce a minimum drag (in comparison with that produced for other wings in the family) at lift coefficients of 0. 0.08, and 0.16. A fourth and a fifth wing, having a 75 deg. swept leading edge and an aspect ratio of 1.65, were designed for lift coefficients of 0 and 0.16, respectively. A 70 deg. swept arrow wing with twist and camber designed for an optimum loading at a lift coefficient considerably less than that for maximum lift-drag ratio gave the highest lift-drag ratio of all the wings tested a value of 8.8 compared with a value of 8.1 for the corresponding wing without twist and camber. Two twisted and cambered wings designed for optimum loading at the lift coefficient for maximum lift-drag ratio gave only small increases in maximum lift-drag ratios over that obtained for the corresponding flat wings. However, in all cases, the lift-drag ratios obtained were far below the theoretical estimates.

Carlson, Harry W.↗

NASA NTRS1959

An Experimental Investigation of a Triangular Wing of Aspect Ratio 2 and a Body Warped to be Trimmed at M = 2.24

A cambered and twisted triangular wing of aspect ratio 2 in combination with a cambered body was investigated experimentally to determine the effectiveness of the camber in reducing the drag due to lift at trim at supersonic speeds. Four arrangements were tested comprising all combinations of a symmetrical and a cambered wing with a symmetrical and a cambered body. The camber shape investigated was derived by linearized lifting surface theory for triangular wings with sonic leading edges and satisfied the requirement that the wing be trimmed at the design Mach number and lift coefficient. The experimental results for the cambered wing and cambered body showed that the drag coefficient at trim was always greater, at the same lift coefficient, than that for the untrimmed symmetrical wing and body. The trim lift coefficient was positive and decreased with increasing Mach number. At the design Mach number of 2.24, the trim lift coefficient was somewhat lower and the drag coefficient was higher than values predicted by linearized lifting surface theory for the wing alone. A comparison of the trim lift-drag ratio of the cambered wing and cambered body with values obtained by trimming the symmetrical wing and symmetrical body either with a canard or a trailing-edge flap showed that, at approximately the design Mach number the cambered configuration developed a somewhat higher value than the trailing-edge flap configuration but a lower value than the canard configuration.

Adams, Gaynor J.↗

NASA NTRS1960

Transonic and Supersonic Wind-Tunnel Tests of Wing-Body Combinations Designed for High Efficiency at a Mach Number of 1.41

Wind-tunnel force tests of a number of wing-body combinations designed for high lift-drag ratio at a Mach number of 1.41 are reported. Five wings and six bodies were used in making up the various wing-body combinations investigated. All the wings had the same highly swept dis- continuously tapered plan form with NACA 65A-series airfoil sections 4 percent thick at the root tapering linearly to 3 percent thick at the tip. The bodies were based on the area distribution of a Sears-Haack body of revolution for minimum drag with a given length and volume. These wings and bodies were used to determine the effects of wing twist., wing twist and camber, wing leading-edge droop, a change from circular to elliptical body cross-sectional shape, and body indentation by the area-rule and streamline methods. The supersonic test Mach numbers were 1.41 and 2.01. The transonic test Mach number range was from 0.6 to 1.2. For the transition-fixed condition and at a Reynolds number of 2.7 x 10(exp 6) based on the mean aerodynamic chord, the maximum value of lift- drag ratio at a Mach number of 1.41 was 9.6 for a combination with a twisted wing and an indented body of elliptical cross section. The tests indicated that the transonic rise in minimum drag was low and did not change appreciably up to the highest test Mach number of 2.01. The lower values of lift-drag ratio obtained at a Mach number of 2.01 can be attributed to the increase of drag due to lift with Mach number.

Grant, Frederick C.↗

NASA NTRS1958

Wind-Tunnel Investigation of Some Effects of Wing Sweep and Horizontal-Tail Height on the Static Stability of an Airplane Model at Transonic Speeds

A research model of an airplane with a configuration suitable for supersonic flight was tested at transonic speeds in order to establish the effects on longitudinal and lateral stability of certain changes in both wing sweep and height of the horizontal tail. Two wings of aspect ratio 3 and taper ratio 0.15, one having the quarter-chord line swept back 30 deg and the other 45 deg, were each tested with the horizontal tail of the model in a low and in a high position. One configuration was also tested with fuselage strakes. The tests were made at Mach numbers from 0.60 to 1.17 and Reynolds numbers from 1.9 x 10(exp 6) to 2.6 x 10(exp 6). The results indicated that a low horizontal-tail position (below the wing-chord plane) gave positive longitudinal stability for the model for all angles of attack used (angles of attack up to 24 deg); whereas, a higher tail position (above the wing-chord plane) resulted in a large reduction in stability at moderate angles of attack. With the higher horizontal tail, the 30 deg-swept-wing model had somewhat more stability than the 45 deg-swept-wing model at subsonic Mach numbers. With the lower tail, the 45 deg-swept-wing model had slightly more stability at all Mach numbers. The model with the 30 deg swept wing had greater directional stability with the tail in the higher rather than the lower position, but the opposite was true for the 45 deg-swept-wing model. The directional stability decreased sharply at high angles of attack; this characteristic was alleviated by the use of fuselage strakes which, however, proved to be detrimental to the longitudinal stability of the model tested.

Fisher, Lewis R.↗

NASA NTRS2003

Transonic Experimental Observations of Abrupt Wing Stall on an F/A-18E Model (Invited)

A transonic wind tunnel test of an 8% F/A-18E model was conducted in the NASA Langley Research Center (LaRC) 16 ft Transonic Tunnel (16-ft TT) to investigate on-surface flow physics during stall. The technical approach employed focused on correlating static (or time-averaged) and unsteady wind-tunnel test data to the unsteady wing-stall events using force, moment, pressure, and pressure-sensitive-paint measurements. This paper focuses on data obtained on the pre-production configuration of the F/A-18E aircraft at Mach number of 0.90. The flow unsteadiness occurring on the wing as the wing went through the stall process was captured using the time history of balance and pressure measurements and by calculating the root mean square (RMS) for a number of instrument signals. The second step was to gather global perspectives on the pressures influencing the wing stall process. The abrupt wing stall experienced by the 8% F/A-18E Model was observed to be an unsteady event triggered by the rapid advancement of separation, which had migrated forward from the trailing edge, to the leading-edge flap hingeline over a very small increment in angle of attack. The angle of attack at which this stall occurred varied, from run to run, over an 1 deg increment. The abrupt wing stall was observed, using pressure-sensitive-paint, to occur simultaneously on both wing panels or asymmetrically. The pressure-sensitive paint data and wingroot bending moment data were essential in providing insight to the flow structures occurring over the wing and the possible asymmetry of those flow structures. A repeatability analysis conducted on eight runs of static data provided a quick and inexpensive examination of the unsteady aerodynamic characteristics of abrupt wing stall. The results of the repeatability analysis agreed extremely well with data obtained using unsteady measurement techniques. This approach could be used to identify test conditions for more complex unsteady data measurements using special instrumentation.

McMillin, S. Naomi↗

NASA NTRS1998

Static Performance of a Wing-Mounted Thrust Reverser Concept

An experimental investigation was conducted in the Jet-Exit Test Facility at NASA Langley Research Center to study the static aerodynamic performance of a wing-mounted thrust reverser concept applicable to subsonic transport aircraft. This innovative engine powered thrust reverser system is designed to utilize wing-mounted flow deflectors to produce aircraft deceleration forces. Testing was conducted using a 7.9%-scale exhaust system model with a fan-to-core bypass ratio of approximately 9.0, a supercritical left-hand wing section attached via a pylon, and wing-mounted flow deflectors attached to the wing section. Geometric variations of key design parameters investigated for the wing-mounted thrust reverser concept included flow deflector angle and chord length, deflector edge fences, and the yaw mount angle of the deflector system (normal to the engine centerline or parallel to the wing trailing edge). All tests were conducted with no external flow and high pressure air was used to simulate core and fan engine exhaust flows. Test results indicate that the wing-mounted thrust reverser concept can achieve overall thrust reverser effectiveness levels competitive with (parallel mount), or better than (normal mount) a conventional cascade thrust reverser system. By removing the thrust reverser system from the nacelle, the wing-mounted concept offers the nacelle designer more options for improving nacelle aero dynamics and propulsion-airframe integration, simplifying nacelle structural designs, reducing nacelle weight, and improving engine maintenance access.

Asbury, Scott C.↗

NASA NTRS2007

Innovative Concept for a Heavy-Load Aircraft Utilizing a Two-Dimensional Wing

Heavy-load aircraft of conventional wing-body-tail design have become very large. Excessive size of such aircraft may present problems in the manufacturing process. In addition, large wing spans may cause some difficulties in ground handling. Increasing lift loads on large span cantilever wings will also increase the strength of the wing tip vortex. The concept presented herein proposes a means for substantially increasing the lift load capability of an aircraft without increasing the overall length and span of the configuration. The concept has a rectangular wing with a relatively low span and a large chord to provide the area required for high lift. Large fuselages are attached at each wing tip to provide the volume required for heavy loading. The fuselages serve as endplates for the wing and should preclude tip flow so that two-dimensional flow might be established on the wing. Elimination of the wing tip flow should prevent the formation of a tip vortex and eliminate the tip vortex hazard to trailing aircraft. Exploratory wind tunnel tests of such an aircraft concept have been conducted. Lessons learned from these tests are discussed herein in an effort to determine the validity of the concept.

Spearman, M. Leroy↗

NASA NTRS2013

AMELIA CESTOL Test: Acoustic Characteristics of Circulation Control Wing with Leading- and Trailing-Edge Slot Blowing

The AMELIA Cruise-Efficient Short Take-off and Landing (CESTOL) configuration concept was developed to meet future requirements of reduced field length, noise, and fuel burn by researchers at Cal Poly, San Luis Obispo and Georgia Tech Research Institute under sponsorship by the NASA Fundamental Aeronautics Program (FAP), Subsonic Fixed Wing Project. The novel configuration includes leading- and trailing-edge circulation control wing (CCW), over-wing podded turbine propulsion simulation (TPS). Extensive aerodynamic measurements of forces, surfaces pressures, and wing surface skin friction measurements were recently measured over a wide range of test conditions in the Arnold Engineering Development Center(AEDC) National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Ft Wind Tunnel. Acoustic measurements of the model were also acquired for each configuration with 7 fixed microphones on a line under the left wing, and with a 48-element, 40-inch diameter phased microphone array under the right wing. This presentation will discuss acoustic characteristics of the CCW system for a variety of tunnel speeds (0 to 120 kts), model configurations (leading edge(LE) and/or trailing-edge(TE) slot blowing, and orientations (incidence and yaw) based on acoustic measurements acquired concurrently with the aerodynamic measurements. The flow coefficient, Cmu= mVSLOT/qSW varied from 0 to 0.88 at 40 kts, and from 0 to 0.15 at 120 kts. Here m is the slot mass flow rate, VSLOT is the slot exit velocity, q is dynamic pressure, and SW is wing surface area. Directivities at selected 1/3 octave bands will be compared with comparable measurements of a 2-D wing at GTRI, as will as microphone array near-field measurements of the right wing at maximum flow rate. The presentation will include discussion of acoustic sensor calibrations as well as characterization of the wind tunnel background noise environment.

Horne, William C.↗

NASA NTRS2015

Novel Control Effectors for Truss Braced Wing

At cruise flight conditions very high aspect ratio/low sweep truss braced wings (TBW) may be subject to design requirements that distinguish them from more highly swept cantilevered wings. High aspect ratio, short chord length and relative thinness of the airfoil sections all contribute to relatively low wing torsional stiffness. This may lead to aeroelastic issues such as aileron reversal and low flutter margins. In order to counteract these issues, high aspect ratio/low sweep wings may need to carry additional high speed control effectors to operate when outboard ailerons are in reversal and/or must carry additional structural weight to enhance torsional stiffness. The novel control effector evaluated in this study is a variable sweep raked wing tip with an aileron control surface. Forward sweep of the tip allows the aileron to align closely with the torsional axis of the wing and operate in a conventional fashion. Aft sweep of the tip creates a large moment arm from the aileron to the wing torsional axis greatly enhancing aileron reversal. The novelty comes from using this enhanced and controllable aileron reversal effect to provide roll control authority by acting as a servo tab and providing roll control through intentional twist of the wing. In this case the reduced torsional stiffness of the wing becomes an advantage to be exploited. The study results show that the novel control effector concept does provide roll control as described, but only for a restricted class of TBW aircraft configurations. For the configuration studied (long range, dual aisle, Mach 0.85 cruise) the novel control effector provides significant benefits including up to 12% reduction in fuel burn.

White, Edward V.↗

NASA NTRS2017

Computational Analysis of a Wing Designed for the X-57 Distributed Electric Propulsion Aircraft

A computational study of the wing for the distributed electric propulsion X-57 Maxwell airplane configuration at cruise and takeoff/landing conditions was completed. Two unstructured-mesh, Navier-Stokes computational fluid dynamics methods, FUN3D and USM3D, were used to predict the wing performance. The goal of the X-57 wing and distributed electric propulsion system design was to meet or exceed the required lift coefficient 3.95 for a stall speed of 58 knots, with a cruise speed of 150 knots at an altitude of 8,000 ft. The X-57 Maxwell airplane was designed with a small, high aspect ratio cruise wing that was designed for a high cruise lift coefficient (0.75) at angle of attack of 0deg. The cruise propulsors at the wingtip rotate counter to the wingtip vortex and reduce induced drag by 7.5 percent at an angle of attack of 0.6deg. The unblown maximum lift coefficient of the high-lift wing (with the 30deg flap setting) is 2.439. The stall speed goal performance metric was confirmed with a blown wing computed effective lift coefficient of 4.202. The lift augmentation from the high-lift, distributed electric propulsion system is 1.7. The predicted cruise wing drag coefficient of 0.02191 is 0.00076 above the drag allotted for the wing in the original estimate. However, the predicted drag overage for the wing would only use 10.1 percent of the original estimated drag margin, which is 0.00749.

Deere, Karen A.↗