Search NASA⌕ Search

SEARCH · Search NASA

Results for “arraying”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Signatures of Thermal and Electrical Crosstalk in a Microwave Multiplexed Hard X-ray Transition Edge Sensor Array

We investigate the crosstalk between Transition-Edge Sensor (TES) pixels in a 24-pixel hard X-ray spectrometer array fabricated at the Advanced Photon Source, Argonne National Laboratory. Analysis shows thermal cross talk, possibly associated with insufficient thermalization, and rare but larger in magnitude electrical crosstalk between specific perpetrator-victim pixel combinations, potentially due to defects in the bias wiring or microwave multiplexing circuit. We use a method based on group-triggering and averaging to isolate the crosstalk response despite only having access to X-ray photon illumination uniform across the entire array. This allows us to identify thermal and electrical crosstalk between pixel pairs in repeated measurements to the level of 1 part in 1000 or better. In the array under study, the magnitude of observed crosstalk is small but comparable to the resolving power of this pixel design (E/Delta E similar to\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$E/\Delta {}E \sim$$\end{document} 1000 at 20 keV) and so potentially responsible for a degradation in energy resolution of the array at high incident photon rates. Having proven the methods to identify and quantify crosstalk in our setup, we can now consider mitigations.

Triamkitsawat, Panthita↗

Graphene-based tunable dual-band absorbers by ribbon/disk array

This article presents two dual-band absorbers based on graphene one-dimensional (1D)/two-dimensional (2D) patterned arrays in the THz frequencies. In comparison to the previous work, the structure of the proposed device is very simple. Most of the dual-band absorbers are made by the combined resonances of the resonators with various sizes within the structure. In this paper, the proposed absorber is based on the arrays of one element. The graphene patterned arrays have dual capacitive-inductive nature. The circuit model of graphene patterned appears as the infinite number of parallel R–L–C circuits, each representing a single resonant mode. In this paper, the fundamental resonant mode of graphene patterned array is excited at both resonant bands. The impedance matching and resonance conditions are used to achieve two resonance bands with perfect absorption.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Benchmark microgravity experiments and computations for 3D dendritic-array stability in directional solidification

In this study, we present a comprehensive quantitative analysis of stability bands for dendritic arrays during directional solidification of a transparent succinonitrile-0.46 wt % camphor alloy, spanning a broad range of pulling velocities. Taking advantage of the microgravity environment aboard the International Space Station where most convection effects are suppressed, we obtain unique measurements that quantify the stable primary spacing range of spatially extended three-dimensional dendritic array structures under purely diffusive growth conditions. Through carefully designed velocity jump experiments and detailed examination of sub-grain boundary dynamics, we characterize key instabilities, including elimination and tertiary branching, shedding new light on the mechanisms governing dynamic dendritic spacing selection in extended 3D arrays. Phase field simulations are performed to characterize the stability limits of dendritic array structures for quantitative comparison with the flight experiments. Although the simulations capture general trends, significant deviations are noted at the upper stability boundary, indicating the influence of additional, unexplored factors. These findings contribute to a deeper understanding of dendritic growth dynamics and offer valuable benchmark data that could aid in refining predictive models and improving control of dendritic microstructures in metallurgical applications.

36 MATERIALS SCIENCE↗

Optical analogue of relativistic Dirac solitons in binary waveguide arrays

We study analytically and numerically an optical analogue of Dirac solitons in binary waveguide arrays in the presence of Kerr nonlinearity. Pseudo-relativistic soliton solutions of the coupled-mode equations describing dynamics in the array are analytically derived. We demonstrate that with the found soliton solutions, the coupled mode equations can be converted into the nonlinear relativistic 1D Dirac equation. This paves the way for using binary waveguide arrays as a classical simulator of quantum nonlinear effects arising from the Dirac equation, something that is thought to be impossible to achieve in conventional (i.e. linear) quantum field theory. -- Highlights: •An optical analogue of Dirac solitons in nonlinear binary waveguide arrays is suggested. •Analytical solutions to pseudo-relativistic solitons are presented. •A correspondence of optical coupled-mode equations with the nonlinear relativistic Dirac equation is established.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Cooperative single-photon subradiant states in a three-dimensional atomic array

We propose a complete superradiant and subradiant states that can be manipulated and prepared in a three-dimensional atomic array. These subradiant states can be realized by absorbing a single photon and imprinting the spatially-dependent phases on the atomic system. We find that the collective decay rates and associated cooperative Lamb shifts are highly dependent on the phases we manage to imprint, and the subradiant state of long lifetime can be found for various lattice spacings and atom numbers. We also investigate both optically thin and thick atomic arrays, which can serve for systematic studies of super- and sub-radiance. Our proposal offers an alternative scheme for quantum memory of light in a three-dimensional array of two-level atoms, which is applicable and potentially advantageous in quantum information processing. - Highlights: • Cooperative single-photon subradiant states in a three-dimensional atomic array. • Subradiant state manipulation via spatially-increasing phase imprinting. • Quantum storage of light in the subradiant state in two-level atoms.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Nonlocal discrete continuity and invariant currents in locally symmetric effective Schrödinger arrays

We develop a formalism relating nonlocal current continuity to spatial symmetries of subparts in discrete Schrödinger systems. Breaking of such local symmetries hereby generates sources or sinks for the associated nonlocal currents. The framework is applied to locally inversion-(time-) and translation-(time-) symmetric one-dimensional photonic waveguide arrays with Hermitian or non-Hermitian effective tight-binding Hamiltonians. For stationary states the nonlocal currents become translationally invariant within symmetric domains, exposing different types of local symmetry. They are further employed to derive a mapping between wave amplitudes of symmetry-related sites, generalizing also the global Bloch and parity mapping to local symmetry in discrete systems. In scattering setups, perfectly transmitting states are characterized by aligned invariant currents in attached symmetry domains, whose vanishing signifies a correspondingly symmetric density. For periodically driven arrays, the invariance of the nonlocal currents is retained on period average for quasi-energy eigenstates. The proposed theory of symmetry-induced continuity and local invariants may contribute to the understanding of wave structure and response in systems with localized spatial order. - Highlights: • Nonlocal current continuity related to subsystem symmetries in discrete Schrödinger arrays. • Application to 1D (non-) Hermitian bound and scattering tight-binding setups. • Local inversion/translation symmetries described by invariant nonlocal currents. • Generalized parity/Bloch mapping between local-symmetry-related sites via currents. • Time-averaged invariant currents of Floquet states in periodically driven arrays.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Multi-year analysis of physical interactions between solar PV arrays and underlying soil-plant complex in vegetated utility-scale systems

Concerns over the land use changes impacts of solar photovoltaic (PV) development are increasing as PV energy development expands. Co-locating utility-scale solar energy with vegetation may maintain or rehabilitate the land's ability to provide ecosystem services. Previous studies have shown that vegetation under and around the panels may improve the performance of the co-located PV and that PV may create a favorable environment for the growth of vegetation. While there have been some pilot-scale experiments, the existence and magnitude of these benefits of vegetation has not been confirmed in a utility-scale PV facility over multiple years. In this study we use power output data coupled with microclimatic measurements in temperate climates to assess these potential benefits. Here this study combines multi-year microclimatic measurements to analyze the physical interactions between PV arrays and the underlying soil-vegetation system in three utility-scale PV facilities in Minnesota, USA. No significant cooling of PV panels or increased power production was observed in PV arrays with underlying vegetation. Fine soil particle fraction was the highest in soils within PV arrays with the vegetation which was attributable to the lowest wind speeds from the compounding suppression of wind by vegetation and PV arrays. Soil moisture and soil nutrient response to re-vegetation varied between PV facilities, which could be attributed to differing soil texture. No statistically significant vegetation-driven panel cooling was observed in this climate. This finding prompts a need for site-specific studies to identify contributing factors for environmental co-benefits in co-located systems.

14 SOLAR ENERGY↗

"Thermal Stability of Anodic Hafnium Oxide Nanotube Arrays"

Thermal stability of highly ordered Hafnium oxide, HfO2 nanotube arrays prepared through electrochemical anodization approach in the presence of ammonium fluoride is investigated in a temperature range of room temperature to 900 C in flowing Argon atmosphere. The formation of the HfO2 nanotube arrays was monitored by current density transient characteristics during anodization of hafnium metal foil. Morphologies of the as grown and post-annealed HfO2 nanotube arrays were analyzed by X-ray powder diffraction (XRD), Scanning electron microscopy (SEM) and Transmission electron microscopy (TEM). Although monoclinic HfO2 is thermally stable up to 2000K in bulk, the morphology HfO2 nanotube arrays degraded at 900 C. Detailed X-ray photoelectron spectroscopy (XPS) study revealed that the thermal treatment significantly impact the composition and chemical environment of the core elements (Hf, O and F) of HfO2. Possible reasons for the degradation of the nanotube morphology were discussed based on XPS study and possible future improvements were suggested briefly.

Qiu, Xiaofeng↗

Assessing the efficacy of vesicle fusion with planar membrane arrays using a mitochondrial porin as reporter

Research highlights: {yields} We have established a vesicle fusion efficacy assay based on the major non-specific porin of Fusobacterium nucleatum (FomA). {yields} Maximal fusion obtained was almost 150,000 porin insertions during 20 min. {yields} Incorporation can be either first order or exponential kinetics which has implications for establishing protein delivery to biomimetic membranes. -- Abstract: Reconstitution of functionally active membrane protein into artificially made lipid bilayers is a challenge that must be overcome to create a membrane-based biomimetic sensor and separation device. In this study we address the efficacy of proteoliposome fusion with planar membrane arrays. We establish a protein incorporation efficacy assay using the major non-specific porin of Fusobacterium nucleatum (FomA) as reporter. We use electrical conductance measurements and fluorescence microscopy to characterize proteoliposome fusion with an array of planar membranes. We show that protein reconstitution in biomimetic membrane arrays may be quantified using the developed FomA assay. Specifically, we show that FomA vesicles are inherently fusigenic. Optimal FomA incorporation is obtained with a proteoliposome lipid-to-protein molar ratio (LPR) = 50 more than 10{sup 5} FomA proteins could be incorporated in a bilayer array with a total membrane area of 2 mm{sup 2} within 20 min. This novel assay for quantifying protein delivery into lipid bilayers may be a useful tool in developing biomimetic membrane applications.

60 APPLIED LIFE SCIENCES↗

Modeling and experimental study of nucleate boiling on a vertical array of horizontal plain tubes

An investigation of nucleate boiling on a vertical array of horizontal plain tubes is presented in this paper. Experiments were performed with refrigerant R123 at reduced pressures varying from 0.022 to 0.64, tube pitch to diameter ratios of 1.32, 1.53 and 2.00, and heat fluxes from 0.5 to 40 kW/m{sup 2}. Brass tubes with external diameters of 19.05 mm and average roughness of 0.12 {mu}m were used in the experiments. The effect of the tube spacing on the local heat transfer coefficient along the tube array was negligible within the present range of experimental conditions. For partial nucleate boiling, characterized by low heat fluxes, and low reduced pressures, the tube positioning shows a remarkable effect on the heat transfer coefficient. Based on these data, a general correlation for the prediction of the nucleate boiling heat transfer coefficient on a vertical array of horizontal tubes under flooded conditions was proposed. According to this correlation, the ratio between the heat transfer coefficients of a given tube and the lowest tube in the array depends only on the tube row number, the reduced pressure and the heat flux. By using the proposed correlation, most of the experimental heat transfer coefficients obtained in the present study were predicted within {+-}15%. The new correlation compares reasonably well with independent data from the literature. (author)

42 ENGINEERING↗

Cetyltrimethylammonium bromide assisted self-assembly of NiTe{sub 2} nanoflakes: Nanoflake arrays and their photoluminescence properties

NiTe{sub 2} nanoflakes and their self-assembled nanoflake arrays (one-dimensional nanostructures) have been prepared by a single-step hydrothermal method using Ni(CH{sub 3}COO){sub 2}.4H{sub 2}O, Na{sub 2}TeO{sub 3}, glucose, and cetyltrimethylammonium bromide (CTAB). CTAB was found to strongly influence the structure and morphology of the resultant NiTe{sub 2}. Morphological transformations from nanoflakes to self-assembled nanoflake arrays and then to solid smooth nanowires were observed as CTAB concentration was increased in the growth solution. Photoluminescence of the NiTe{sub 2} self-assembled nanoflake arrays was investigated for the first time and the formation mechanism of the NiTe{sub 2} nanostructures is also discussed. - Graphical abstract: NiTe{sub 2} nanoflakes and their self-assembled nanoflake arrays have been prepared by a single-step hydrothermal method using Ni(CH{sub 3}COO){sub 2}.4H{sub 2}O, Na{sub 2}TeO{sub 3}, glucose, and cetyltrimethylammonium bromide (CTAB).

77 NANOSCIENCE AND NANOTECHNOLOGY↗

P25 niblet-like coated on large void space TiO{sub 2} nanotubes arrays for high-rate charge-collection and improved photoconversion efficiency

A niblet-like P25-coated large void space TiO{sub 2} nanotubes arrays (PCTs) has been synthesized by decorating P25 nanoparticles on a rapidly-synthesized large void space TiO{sub 2} nanotube arrays (LTAs) with an appropriate hydrothermal treatment approach in a Teflon-lined stainless steel autoclave. Some key factors and probable synthetic mechanisms have been investigated to obtain an optimal route. Exhilaratingly, the as-synthesized PCTs and LTAs show impressive morphologies, structures and very large void space. And the most important is that, compared with LTAs, the decorated PCTs demonstrates significantly improved dye loading and high-rate charge-collection capability and thus leads to a more than double of the solar cell efficiency than that of LTAs (from 1.46% of LTAs to 3.00% of PCTs under simulated AM 1.5 conditions in our case). - Graphical abstract: The top view and cross-section SEM images of obtained electrode materials (LTAs and PCTs), with the schematic diagram (on the right) showing the kinetic advantages of the PCTs in charge collection and transmission. Highlights: Black-Right-Pointing-Pointer A large void space TiO{sub 2} nanotubes arrays (LTAs) was fabricated in not more than 12 h. Black-Right-Pointing-Pointer A niblet-like P25-coated void space TiO{sub 2} nanotubes arrays (PCTs) has been synthesized based on the LTAs. Black-Right-Pointing-Pointer Some key factors, probable synthetic mechanisms and optimal synthetic route are investigated. Black-Right-Pointing-Pointer The PCTs and LTAs show impressive morphologies, structures and greatly improved dye loading capability. Black-Right-Pointing-Pointer The PCTs shows enhanced charge-collection and light scattering properties and double solar cell efficiency.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Controllable hydrothermal synthesis of rutile TiO{sub 2} hollow nanorod arrays on TiCl{sub 4} pretreated Ti foil for DSSC application

Rutile TiO{sub 2} nanorod arrays (TNRs) were achieved by hydrothermal process on TiCl{sub 4} pretreated Ti foil. Subsequently, TNRs were hydrothermally etched in HCl solution to form hollow TiO{sub 2} nanorod arrays (H-TNRs). The TiCl{sub 4} pretreatment plays key roles in enhancement of Ti foil corrosion resistance ability and crystal nucleation introduction for TNRs growth. TNRs with desired morphology can be obtained by controlling TiCl{sub 4} concentration and the amount of tetrabutyl titanate (TTB) accordingly. TNRs with the length of ∼1.5 μm and diameter of ∼200 nm, obtained on 0.15 M TiCl{sub 4} pretreated Ti foil with 0.6 mL TTB, exhibits relatively higher photocurrent. The increased pore volume of the H-TNRs has contributed to the increased surface area which is benefit for Dye-Sensitized Solar Cells (DSSC) application. And the 180 °C-H-TNRs photoanode obtained from the 0.15-TiCl{sub 4}-TNRs sample demonstrated 128.9% enhancement of photoelectric efficiency of DSSC compared to that of the original TNR photoanode. - Graphical abstract: Rutile hollow TiO{sub 2} nanorod array photoanode obtained from original TiO{sub 2} nanorod array photoanode by hydrothermal etching demonstrates enhanced photoelectric efficiency of DSSC. - Highlights: • TiO{sub 2} nanorods are prepared via hydrothermal process on TiCl{sub 4}-pretreated Ti foil. • Hollow TiO{sub 2} nanorods are obtained by hydrothermal etching of TiO{sub 2} nanorods. • TiCl{sub 4} pretreatment plays a key role in protecting Ti foil from chemical corrosion. • Hollow TiO{sub 2} nanorods photoanode shows enhanced photoelectric efficiency for DSSC.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Cu-PDC-bpa solid coordination frameworks (PDC=2,5-pyrindinedicarboxylate; bpa=1,2-DI(4-pyridil)ethane)): 2D and 3D structural flexibility producing a 3-c herringbone array next to ideal

Combination of polycarboxylate anions and dipyridyl ligands is an effective strategy to produce solid coordination frameworks (SCF) which are crystalline materials based on connections between metal ions through organic ligands. In this context, this work is focused on two novel Cu{sup II}-based SCFs exhibiting PDC (2,5-pyridinedicarboxylate) and bpa (1,2-di(4-pyridyl)ethane), being the first structures reported in literature containing both ligands. Chemical formula are [Cu{sub 2}[(PDC){sub 2}(bpa)(H{sub 2}O){sub 2}]·3H{sub 2}O·DMF (1), and [Cu{sub 2}(PDC){sub 2}(bpa)(H{sub 2}O){sub 2}]·7H{sub 2}O (2), where DMF is dimethylformamide. Compounds 1 and 2 have been characterized by means of X-ray diffraction (XRD), infrared spectroscopy (IR), thermogravimetric (TG) analysis, differential thermal analysis (DTA) and dielectric measurements. The crystallographic analysis revealed that compounds 1 and 2 can be described as herringbone-type layers formed by helicoidal Cu-PDC-Cu chains connected through bpa ligands. Solvent molecules are crystallized between the layers, providing the inter-layer connections through hydrogen bonds. Differences between both compounds are attributable to the flexibility of bpa (in 2D) as well as to the 3D packing of the layers which is solvent dependent. This fact results in the fact that compound 2 is the most regular 3-c herringbone array reported so far. The structural dynamism of these networks is responsible for the crystalline to-amorphous to-crystalline (CAC) transformation from compound 1 to compound 2. Crystallochemical features for both compounds have also been studied and compared to similar 3-connected herringbone-arrays. - Graphical abstract: Cu-PDC-bpa 3-c herringbone arrays. - Highlights: • The most ideal herringbone array reported so far is a Cu-PDC-bpa SCF. • Conformational freedom of bpa results in 2D and 3D flexibility of the SCFs. • The flexibility of the SCFs is related to a phase transformation. • Dielectric measurements confirm the mobility of guest solvent molecules.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Seed layer-free electrodeposition of well-aligned ZnO submicron rod arrays via a simple aqueous electrolyte

A potentiostatic electrodeposition technique was used to directly fabricate large-scale, well-aligned, and single-crystalline submicron ZnO rod arrays on tin doped indium oxide glass substrate without a pre-prepared seed layer of ZnO from an aqueous solution only containing zinc nitrate. The effects of electrochemical parameters, such as electrodeposition potential, electrodeposition duration, solution temperature, and precursor concentration, on the orientation, morphology, aspect ratio, and growth rate of ZnO rod arrays were systematically investigated. Results show that submicron ZnO rod arrays with (0 0 0 2) preferred orientation and perfect crystallization were obtained when electrodeposition potential was in the range from -0.6 to -1.1 V and solution temperature was controlled above 60 deg. C. Both high solution temperature and low precursor concentration resulted in the decrease in rod diameters. Photoluminescence measures showed that small diameter and nanotips of ZnO rod arrays should be responsible for strong and sharp ultraviolet emission in the room temperature photoluminescence spectra.

36 MATERIALS SCIENCE↗

Electrochemically synthesized visible light absorbing vertically aligned N-doped TiO{sub 2} nanotube array films

Graphical abstract: Display Omitted Highlights: ► Single step electrochemical synthesis of N-doped TiO{sub 2} nanotube array films. ► Effective substitutional N-doping achieved. ► Different N-concentrations were achieved by varying the N-precursor concentration in the electrolyte. ► Visible light absorption observed at high N-doping. -- Abstract: Visible light absorbing vertically aligned N-doped anatase nanotube array thin films were synthesized by anodizing Ti foils in ethylene glycol + NH{sub 4}F + water mixture containing urea as nitrogen source. Different nitrogen concentrations were achieved by varying the urea content in the electrolyte. The structure, morphology, composition and optical band gap of the nanotube arrays were determined by X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy (XPS) and diffuse reflectance spectroscopy, respectively. The substitution of O{sup 2−} ions by N{sup 3−} ions in the anion sublattice as well as the formulae of the doped samples was confirmed from the results of XPS. The optical band gap of the nanotube arrays was found to decrease with N-concentration. The sample with the highest concentration corresponding to the formula TiO{sub 1.83}N{sub 0.14} showed two regions in the Tauc's plot indicating the presence of interband states.

36 MATERIALS SCIENCE↗

Tunable synthesis of TiO{sub 2}/SrO core/shell nanowire arrays with enhanced photocatalytic activity

Graphical abstract: TiO{sub 2} nanowires with tunable SrO shell layer are easily fabricated. The core/shell structure can enhance the photocatalytic activity of TiO{sub 2} nanowires and restrict the recombination of the electrons/holes. Display Omitted Highlights: ► A facile method to fabricate TiO{sub 2}/SrO core-shell nanowire array is reported. ► The thickness of SrO shell layer can be tunable by adjusting the dipping time. ► TiO{sub 2}/SrO core/shell nanowires shows enhanced photocatalytic activity. -- Abstract: We report a simple method to fabricate well-aligned TiO{sub 2}/SrO core/shell nanowire arrays. The core/shell structure is confirmed to have crystalline TiO{sub 2} nanowires core and amorphous SrO shell layer. The shell is composed of SrO with tunable thickness. Photocatalytic activity measurement shows that TiO{sub 2}/SrO core/shell nanowire arrays outperform uncovered TiO{sub 2} nanowires. Such core/shell nanowire arrays have potential applications for photovoltaic devices and as high performance photocatalyst.

36 MATERIALS SCIENCE↗

Synthesis of visible-light absorbing CoFe{sub 2}O{sub 4} sensitized TiO{sub 2} nanotube arrays electrode with enhanced photoelectrochemical performance

Graphical abstract: - Highlights: • TiO{sub 2} nanotube sensitized with CoFe{sub 2}O{sub 4} nanocrystals was synthesized by a facile hydrothermal method. • CoFe{sub 2}O{sub 4} nanocrystals were loaded to the outer and inner surface of TiO{sub 2} nanotube. • The CoFe{sub 2}O{sub 4} sensitized TiO{sub 2} nanotube electrode has a strong photoresponse to the light. - Abstract: TiO{sub 2} nanotube arrays sensitized with CoFe{sub 2}O{sub 4} nanocrystals were successfully synthesized via a facile hydrothermal method. The as-prepared sample was studied by X-ray diffraction (XRD), field emission scanning electron microscopy (SEM), transmission electron microscopy (TEM), and energy-dispersive X-ray spectroscopy (EDX) to characterize its phase structure, morphology and chemical composition. Enhanced absorption in both UV and visible-light regions was observed for the CoFe{sub 2}O{sub 4} sensitized TiO{sub 2} nanotube arrays. The photocurrent density of CoFe{sub 2}O{sub 4} sensitized TiO{sub 2} nanotube arrays electrode was 30 times as great as that of bare TiO{sub 2} nanotube arrays electrode.

36 MATERIALS SCIENCE↗