Search NASA⌕ Search

SEARCH · Search NASA

Results for “compositional properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

An Evaluation of the Iosipescu Specimen for Composite Materials Shear Property Measurement

A detailed evaluation of the suitability of the Iosipescu specimen tested in the modified Wyoming fixture is presented. An experimental investigation using conventional strain gage instrumentation and moire interferometry is performed. A finite element analysis of the Iosipescu shear test for unidirectional and cross-ply composites is used to assess the uniformity of the shear stress field in the vicinity of the notch, and demonstrate the effect of the nonuniform stress field upon the strain gage measurements used for the determination of composite shear moduli. From the test results for graphite-epoxy laminates, it is shown that the proximity of the load introduction point to the test section greatly influences the individual gage readings for certain fiber orientations but the effect upon shear modulus measurement is relatively unimportant. A numerical study of the load contact effect shows the sensitivity of some fiber configurations to the specimen/fixture contact mechanism and may account for the variations in the measured shear moduli. A comparison of the strain gage readings from one surface of a specimen with corresponding data from moire interferometry on the opposite face documented an extreme sensitivity of some fiber orientations to eccentric loading which induced twisting and yielded spurious shear stress-strain curves. In the numerical analysis, it is shown that the Iosipescu specimens for different fiber orientations have to be modeled differently in order to closely approximate the true loading conditions. Correction factors are needed to allow for the nonuniformity of the strain field and the use of the average shear stress in the shear modulus evaluation. The correction factors, which are determined for the region occupied by the strain gage rosette, are found to be dependent upon the material orthotropic ratio and the finite element models. Based upon the experimental and numerical results, recommendations for improving the reliability and accuracy of the shear modulus values are made, and the implications for shear strength measurement discussed. Further application of the Iosipescu shear test to woven fabric composites is presented. The limitations of the traditional strain gage instrumentation on the satin weave and high tow plain weave fabrics is discussed. Test results of a epoxy based aluminum particulate composite is also presented. A modification of the Iosipescu specimen is proposed and investigated experimentally and numerically. It is shown that the proposed new specimen design provides a more uniform shear stress field in the test section and greatly reduces the normal and shear stress concentrations in the vicinity of the notches. While the fabrication and the material cost of the proposed specimen is tremendously reduced, it is shown the accuracy of the shear modulus measurement is not sacrificed.

Ho, Henjen↗

Dielectric properties of novel composites prepared with few layered graphene (FLG)-lithium triniobate (LiNb{sub 3}O{sub 8})

Lithium triniobate (LiNb{sub 3}O{sub 8}) has been prepared using microwave assisted combustion synthesis at a low temperature of 400 °C. Graphite oxide is synthesized using Hummers method and thereafter it is thermally exfoliated at 500 and 700 °C to obtain two samples of Few Layered Graphene (FLG). Then, FLG-LiNb{sub 3}O{sub 8} composites prepared through a simple ultra-sonication assisted solution mixing process. The obtained samples are named as FLN5 and FLN7 based on the temperature used to obtain FLG. Low frequency dielectric measurements are recorded for both the samples and the measured dielectric constant is observed to be more for FLN5 (250 at 60 Hz) than FLN7 (115 at 60 Hz) whilst the dielectric loss is less in case of FLN5 (1.525 at 60 Hz). The enhancement in dielectric properties for FLN5 is explained in terms of polarization in FLG-LiNb{sub 3}O{sub 8} composites.

36 MATERIALS SCIENCE↗

Composite material shear property measurement using the Iosipescu specimen

A detailed evaluation of the suitability of the Iosipescu specimen tested in the modified Wyoming fixture is presented. Finite element analysis and moire interferometry are used to assess the uniformity of the shear stress field in the test section of unidirectional and cross-ply graphite-epoxy composites. The nonuniformity of the strain field and the sensitivity of some fiber orientations to the specimen/fixture contact mechanics are discussed. The shear responses obtained for unidirectional and cross-ply graphite-epoxy composites are discussed and problems associated with anomalous behavior are addressed. An experimental determination of the shear response of a range of material systems using strain gage instrumentation and moire interferometry is performed.

Ho, Henjen↗

Mechanical & morphological properties of attapulgite/NR composites: Effect of mixing time variation

The development of composite material based on attapulgite clay (ATP) as a filler and natural rubber (NR) matrices were prepared by combination of melt mixing and latex compounding methods. Sonication technique was chosen in this work to disperse the attapulgite suspension. 6 phr of attapulgite loading was fabricated using different time of mixing ranging from 30 minutes until 2 hours and sonication time was kept constant at 15 minutes. Then, co-coagulating HA latex with attapulgite clay suspension through latex compounding method produced the masterbatch. The masterbatch was compounded with natural rubber by melt mixing method. The mechanical and morphological characteristics were investigated in this work. From mechanical testing, M1 showed the highest value of tensile and tear strength. By comparing with M30 and M2, M1 shows high 300% tensile modulus and lower crosslink density. However, when the time of mixing was prolonged to 2 hours, the results for tensile strength, elongation at break and tear strength were decreased. This is due to flocculation of attapulgite particles. Sonication techniques also proved that the tensile strength and elongation at break of these three samples were higher compared to gum NR (NR) and attapulgite compounded with NR using a conventional method (in-situ 6). From field emission scanning electron microscope (FESEM) results, it revealed that M1 had good dispersion in the NR system. It is proved that the higher tensile strength was due to good dispersion of attapulgite clay in the NR matrix. It was also supported from crosslink density, which is lower than NR and in-situ 6 results. It showed that the penetration of toluene solvent into rubber compound was restricted. The optimum time, M1 give the best results, which can be compared to control the sample.

36 MATERIALS SCIENCE↗

Synthesis, modular composition, and electrochemical properties of lamellar iron sulfides

Transition metal chalcogenides with layered structures are promising materials for energy storage, catalysis, and electronics, among other areas. We have identified a new layered phase of iron sulfide containing interlayer solvated cations. We present an optimized synthesis for the Li + -containing material from an Fe(III) xanthate complex. Structure and composition data indicate the material consists of poorly-ordered iron sulfide layers separated by solvated cations. The lamellar spacing in these materials can be tuned by changing the identity of the cation. Furthermore, the lamellar spacing can also be reversibly tuned by the degree of solvation of the material. The material is electrically conductive and can serve as a pseudocapacitor with comparable performance to commercial materials such as MnO 2 . Finally, these materials also show promise as lithium or sodium ion battery cathodes with good capacity and reversibility.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

SCOPING MELTING STUDIES OF HIGH ALUMINA WASTE GLASS COMPOSITIONS

Glass property models will be used at the Hanford Tank Waste Treatment and Immobilization Plant to formulate durable high-level waste glasses for disposal. A major effort is focused on expanding glass property models to cover a broader range of wastes and higher waste-loaded glasses. As a part of this effort, a statistically designed matrix of high-alumina glass compositions was developed. Forty five compositions were selected from the matrix to evaluate glass properties. Of these compositions, thirty three produced homogeneous glasses. The other twelve compositions contained segregated phases and high crystallinity; these were iteratively modified in an attempt to produce homogeneous glass samples while altering the original composition as little as possible. This paper focuses on the characterization of the twelve inhomogeneous compositions and their modifications using X-ray diffraction, scanning electron microscopy, and energy dispersive spectroscopy.

Kroll, Jared O.↗

Multi-Scale Analysis of Effective Mechanical Properties of 3D Woven Composite Materials

This work aims to compute and analyze the mechanical properties of 3D woven composite materials that share the same yarn structure but differ in their matrix porosity and fiber volume fraction. Assuming linear elastic behavior, the software PuMA, developed at NASA, was used to characterize the different composites from their constituents' data averaging their elastic properties in three main directions to obtain their effective orthotropic mechanical properties. This was performed in three steps: firstly, the different phases (yarns/matrix) were analyzed as anisotropic materials separately at the micro-scale; then, the results from these analyses were homogenized and used to obtain the anisotropic elasticity tensor at the meso-scale for the different woven materials; and finally, assuming orthotropic mechanical behavior for the unit cell the mechanical properties were obtained at the macro-scale. The 3D woven composite materials selected for this study are made of phenolic resin with porosity values between 0 and 0.6, and resin infiltrated carbon fiber with volume fractions between 0.5 and 0.9 for the yarns. Results from PuMA were validated with external FEA simulations for the non-porous 3D woven material with a fiber volume fraction of 0.9 in the yarns. Results will be included in the final paper after completing the study detailed in Section II.

Sergio Fraile Izquierdo↗

Composition-dependent Magnetic Properties of BiFe03-BaTi03 Solid Solution Nanostructures

We report on the Moessbauer spectra and magnetization properties of single-crystalline (BiFeO{sub 3}){sub x-}(BaTiO{sub 3}){sub 1-x} solid solution nanostructures in the form of nanocubes, measuring approximately 150 to 200 nm on a side, prepared by a molten salt solid-state reaction method in the compositional range wherein 0.5 {le} x {le} 1. Powder x-ray diffraction (XRD) and monochromatic synchrotron XRD studies indicate products of high purity, which undergo gradual, well-controlled structural transformations from rhombohedral to tetragonal structures with decreasing 'x.' For all solid solution products, room-temperature magnetization studies exhibit hysteretic behavior with remnant magnetization values of M{sub r} {ge} 0.32 emu/g, indicating that the latent magnetization locked within the toroidal spin structure of BiFeO{sub 3} has been released. Room-temperature Moessbauer spectra show composition-dependent characteristics with decreasing magnetic hyperfine field values and increasing absorption linewidths due to a decrease in the magnetic exchange interaction strength with decreasing x. For the lowest x=0.5 composition studied, the Moessbauer spectra show paramagnetic behavior, indicating a Neel temperature for this composition below 300 K. However, room-temperature magnetization studies with applied fields of up to 50 kOe show hysteretic behavior for all compositions, including the x=0.5 composition, presumably due to field-induced ordering. Furthermore, hysteresis loops for all compositions exhibit smaller coercivities at 10 K than at 300 K, an observation that may suggest the presence of magnetoelectric coupling in these systems.

36 MATERIALS SCIENCE↗

Structure and properties of polymeric composite materials during 1501 days outer space exposure at Salyut-7 orbital station

Specimens of polymeric composite materials for aviation and space applications such as glass fiber reinforced plastics (GFRP), carbon fiber reinforced plastics (CFRP), organic fiber reinforced plastics (OFRP), and hybrid plastics (HP) based on epoxy compounds were exposed to the space environment on the surface of Salyut-7 orbital station. The space exposure lasted 1501 days as a maximum. The data relating to the change in mechanical properties, mass losses, glass transition temperature, linear thermal expansion coefficient, and microstructure after various periods of exposure are given. It has been found that the change in properties is caused by the processes of binder postcuring and microerosion of the exposed surface of plastics. The phenomenon of strengthening of the surface layer of hybrid composites, due to which the nature of destruction changes at bending loads, has been revealed.

Startsev, Oleg V.↗

An evaluation of the Iosipescu specimen for composite materials shear property measurement

A detailed evaluation of the suitability of the Iosipescu specimen tested in the modified Wyoming fixture is presented. A linear finite element model of the specimen is used to assess the uniformity of the shear stress field in the vicinity of the notch, and demonstrate the effect of the nonuniform stress field upon strain gage measurements used for the determination of composite shear moduli. Based upon test results from graphite-epoxy laminates, the proximity of the load introduction point to the test section and the material orthotropy greatly influence the individual gage readings, however, shear modulus determination is not significantly affected by the lack of pure shear. Correction factors are needed to allow for the nonuniformity of the strain field and the use of the average shear stress in the shear modulus evaluation. The correction factors are determined for the region occupied by the strain gage rosette. A comparison of the strain gage readings from one surface of a specimen with corresponding data from moire interferometry on the opposite face documented an extreme sensitivity of some fiber orientations to eccentric loading which induced twisting and spurious shear stress-strain curves. The discovery of specimen twisting explains the apparently inconsistent shear property data found in the literature. Recommendations for improving the reliability and accuracy of the shear modulus values are made, and the implications for shear strength measurement discussed.

Morton, J.↗

Correlation of Structural Differences between Nafion/Polyaniline and Nafion/Polypyrrole Composite Membranes and Observed Transport Properties

Polyaniline/Nafion and polypyrrole/Nafion composite membranes, prepared by chemical polymerization, are studied by infrared and nuclear magnetic resonance spectroscopy, and scanning electron microscopy. Differences in vanadium ion diffusion through the membranes and in the membranes’ area specific resistance are linked to analytical observations that polyaniline and polypyrrole interact differently with Nafion. Polypyrrole, a weakly basic polymer, binds less strongly to the sulfonic acid groups of the Nafion membrane, and thus the hydrophobic polymer aggregates in the center of the Nafion channel rather than on the hydrophilic side chains of Nafion that contain sulfonic acid groups. This results in a drastically elevated membrane resistance and an only slightly decreased vanadium ion permeation compared to a Nafion membrane. Polyaniline on the other hand is a strongly basic polymer, which forms along the sidewalls of the Nafion pores and on the membrane surface, binding tightly to the sulfonic acid groups of Nafion. This leads to a more effective reduction in vanadium ion transport across the polyaniline/Nafion membranes and the increase in membrane resistance is less severe. The performance of selected polypyrrole/Nafion composite membranes is tested in a static vanadium redox cell. Increased coulombic efficiency, compared to a cell employing Nafion, further confirms the reduced vanadium ion transport through the composite membranes.

74 ATOMIC AND MOLECULAR PHYSICS↗

EMTA’s Evaluation of the Elastic Properties for Fiber Polymer Composites Potentially Used in Hydropower Systems

Fiber-reinforced polymer composites can offer important advantages over metals where lightweight, cost-effective manufacturing and high mechanical performance can be achieved. To date, these materials have not been used in hydropower systems. In view of the possibility to tailor their mechanical properties to specific applications, they now have become a subject of research for potential use in hydropower systems. The first step in any structural design that uses composite materials consists of evaluating the basic composite mechanical properties as a function of the as-formed composite microstructure. These basic properties are the elastic stiffness, stress-strain response, and strength. This report describes the evaluation of the elastic stiffness for a series of common discontinuous fiber polymer composites processed by injection molding and compression molding in order to preliminarily estimate whether these composites could be used in hydropower systems for load-carrying components such as turbine blades. To this end, the EMTA (Copyright © Battelle 2010) predictive modeling tool developed at the Pacific Northwest National Laboratory (PNNL) has been applied to predict the elastic properties of these composites as a function of three key microstructural parameters: fiber volume fraction, fiber orientation distribution, and fiber length distribution. These parameters strongly control the composite mechanical performance and can be tailored to achieve property enhancement. EMTA uses the standard and enhanced Mori-Tanaka type models combined with the Eshelby equivalent inclusion method to predict the thermoelastic properties of the composite based on its microstructure.

36 MATERIALS SCIENCE↗

The Distribution, Composition, and Particle Properties of Mars Mesospheric Aerosols: an Analysis of CRISM Visible/near-IR Limb Spectra with Context from Near-Coincident MCS and MARCI Observations

The Compact Reconnaissance Imaging Spectral Mapper (CRISM) onboard the Mars Reconnaissance Orbiter (MRO) obtains pole-to-pole observations (i.e., full MRO orbits) of vertical profiles for visible/near-IR spectra (λ=0.4–4.0 μm), which are ideally suited to identifying the composition and particle sizes of Mars ice and dust aerosols over 50–100 km altitudes in the Mars mesosphere. Within the coverage limitations of the CRISM limb data set, a distinct compositional dichotomy is found in Mars mesospheric ice aerosols. CO2 ice clouds appear during the aphelion period of Mars orbit (Solar Longitudes, Ls∼0–160°) at low latitudes (∼20S–10N) over specific longitude regions (Meridiani, Valles Marineris) and at typical altitudes of 55–75 km. Apart from faint water ice hazes below 55 km, mesospheric H2O ice clouds are primarily restricted to the perihelion orbital range (Ls∼160 – 350°) at northern and southern mid-to-low latitudes with less apparent longitudinal dependences. Mars mesospheric CO2 clouds are presented in CRISM spectra with a surprisingly large range of particle sizes (cross section weighted radii, Reff=0.3 to 2.2 μm). The smaller particle sizes (Reff ≤1 μm) appear concentrated near the spatial (latitude and altitude) boundaries of their global occurrences. CRISM spectra of mesospheric CO2 clouds also show evidence of iridescence, indicating very narrow particle size distributions (effective variance, Veff∼0.03) and so very abrupt CO2 cloud nucleation. Furthermore, these clouds are sometimes accompanied by altitude coincident peaks in 1.27 μm O2 dayglow, which indicates very dry, cold regions of formation. Mesospheric water ice clouds generally exhibit small particle sizes (Reff=0.1–0.3 μm), although larger particle sizes (Reff=0.4–0.7 μm) appear infrequently. On average, water ice cloud particle sizes decrease with altitude over 50–80 km in the perihelion mesosphere. Water ice mass appears similar in clouds over a large range of observed cloud particle sizes, with particle number densities increasing to ∼10 cm−3 for Reff=0.2 μm. Near coincident Mars Climate Sounder (MCS) temperature and aerosol profile measurements for a subset of CRISM mesospheric aerosol measurements indicate near saturation (H2O and CO2) conditions for ice clouds and distinct mesospheric temperature increases associated with mesospheric dust loading. Dayside (3 pm) mesospheric CO2 clouds with larger particle sizes (Reff ≥0.5 μm) scatter surface infrared emission in MCS limb infrared radiances, as well as solar irradiance in the MCS solar band channel. Scattering of surface infrared emission is most strikingly presented in nighttime (3 am) MCS observations at 55–60 km altitudes, indicating extensive mesospheric nighttime CO2 clouds with considerably larger particle sizes (Reff∼7 μm). Mesospheric CO2 ice clouds present cirrus-like waveforms over extensive latitude and longitude regions (10°×10°), as revealed in coincident Mars Color Imager (MARCI) nadir imaging. Solar tides, gravity waves, and the large orbital variation of the extended thermal structure of the Mars atmosphere influence all of these behaviors. Mesospheric dust aerosols appear infrequently over the non-global (planet encircling) dust storm era of the CRISM limb data set (2009–2016), and exhibit smaller particle sizes (Reff=0.2–0.7 μm) relative to dust in the lower atmosphere. One isolated case of an aphelion (Ls=96°) mesospheric dust layer with large dust particle sizes (Reff ∼2 μm) over Syria Planum may reflect high altitude, non-local transport of dust over elevated regions.

Clancy, Todd R.↗

The distribution, composition, and particle properties of Mars mesospheric aerosols: An analysis of CRISM visible/near-IR limb spectra with context from near-coincident MCS and MARCI observations

The Compact Reconnaissance Imaging Spectral Mapper (CRISM) onboard the Mars Reconnaissance Orbiter (MRO) obtains pole-to-pole observations (i.e., full MRO orbits) of vertical profiles for visible/near-IR spectra (λ= 0.4–4.0 μm), which are ideally suited to identifying the composition and particle sizes of Mars ice and dust aerosols over 50–100 km altitudes in the Mars mesosphere. Within the coverage limitations of the CRISM limb data set, a distinct compositional dichotomy is found in Mars mesospheric ice aerosols. CO2 ice clouds appear during the aphelion period of Mars orbit (Solar Longitudes, L(s )∼ 0–160°) at low latitudes (∼20S–10N) over specific longitude regions (Meridiani, Valles Marineris) and at typical altitudes of 55–75 km. Apart from faint water ice hazes below 55 km, mesospheric H2O ice clouds are primarily restricted to the perihelion orbital range (L(s)∼160 – 350°) at northern and southern mid-to-low latitudes with less apparent longitudinal dependences. Mars mesospheric CO2 clouds are presented in CRISM spectra with a surprisingly large range of particle sizes (cross section weighted radii, R(eff) = 0.3 to 2.2 μm). The smaller particle sizes (R(eff) ≤1 μm) appear concentrated near the spatial (latitude and altitude) boundaries of their global occurrences. CRISM spectra of mesospheric CO2 clouds also show evidence of iridescence, indicating very narrow particle size distributions (effective variance, V(eff) ∼ 0.03) and so very abrupt CO2 cloud nucleation. Furthermore, these clouds are sometimes accompanied by altitude coincident peaks in 1.27 μm O2 dayglow, which indicates very dry, cold regions of formation. Mesospheric water ice clouds generally exhibit small particle sizes (R(eff) = 0.1–0.3 μm), although larger particle sizes (R(eff) = 0.4–0.7 μm) appear infrequently. On average, water ice cloud particle sizes decrease with altitude over 50–80 km in the perihelion mesosphere. Water ice mass appears similar in clouds over a large range of observed cloud particle sizes, with particle number densities increasing to ∼10 per cu. cm for R(eff) = 0.2 μm. Near coincident Mars Climate Sounder (MCS) temperature and aerosol profile measurements for a subset of CRISM mesospheric aerosol measurements indicate near saturation (H2O and CO2) conditions for ice clouds and distinct mesospheric temperature increases associated with mesospheric dust loading. Dayside (3 pm) mesospheric CO2 clouds with larger particle sizes (R(eff) ≥0.5 μm) scatter surface infrared emission in MCS limb infrared radiances, as well as solar irradiance in the MCS solar band channel. Scattering of surface infrared emission is most strikingly presented in nighttime (3 am) MCS observations at 55–60 km altitudes, indicating extensive mesospheric nighttime CO2 clouds with considerably larger particle sizes (R(eff)∼7 μm). Mesospheric CO2 ice clouds present cirrus-like waveforms over extensive latitude and longitude regions (10°×10°), as revealed in coincident Mars Color Imager (MARCI) nadir imaging. Solar tides, gravity waves, and the large orbital variation of the extended thermal structure of the Mars atmosphere influence all of these behaviors. Mesospheric dust aerosols appear infrequently over the non-global (planet encircling) dust storm era of the CRISM limb data set (2009–2016), and exhibit smaller particle sizes (R(eff) = 0.2–0.7 μm) relative to dust in the lower atmosphere. One isolated case of an aphelion (L(s) = 96°) mesospheric dust layer with large dust particle sizes (R(eff) ∼2 μm) over Syria Planum may reflect high altitude, non-local transport of dust over elevated regions.

R. Todd Clancy↗

Role of Sb Compositions on the Properties of InAs/GaAsSb Quantum Dots (QDs)

QD size, uniformity and density in InAs/GaAsSb material system for increasing Sb content are studied using Atomic Force Microscopy (AFM). AFM results show that QD density and uniformity improve with Sb content increase. The improvement of QD uniformity is ensured by the narrowing of the analysis of AFM scans. To obtain minimum VBO, InAs/GaAsSb with various Sb compositions is investigated by PL and TRPL measurements. PL data shows a blue-shift as excitation power increases as evidence of a type II band structure. Since the PL peak of 8 and 13 % Sb samples did not shift while that of 15 % Sb sample is blue-shifted with increasing the excitation power it is concluded that InAs QDs/GaAs0.86Sb0.14 would have minimum valence band offset. This tendency is supported by the change of a carrier lifetime estimated from TRPL data.

14 SOLAR ENERGY↗

Southwestern U.S. Biomass Burning Smoke Hygroscopicity: The Role of Plant Phenology, Chemical Composition, and Combustion Properties

Biomass burning emissions have substantially increased with continued warming and drying in the southwestern U.S., impacting air quality and atmospheric processes. To better quantify impacts of biomass burning aerosols, an extensive laboratory study of fresh smoke emissions was conducted at Los Alamos National Laboratory. Laboratory burn experiments with selected native and invasive southwestern U.S. fuels were used to elucidate the role of fuel type, chemical composition, and ignition method on the hygroscopicity of smoke. Here we focus on a custom controlled relative humidity (RH) nephelometry system using the direct measurement of aerosol light scattering with two nephelometers—one at dry conditions and one at a controlled high RH (RH ~ 85%). Aerosol hygroscopicity was highly variable with the enhancement in light scattering coefficient in the range of 1.02 < f (RH = 85%) < 2.1 and corresponding to the kappa parameter (κ neph ) ranging from ~0 to 0.18. Hygroscopicity is determined primarily by the fuel's inorganic ion content. For example, invasive halophytes with high inorganic salt content exhibit much greater water uptake than native coniferous species with low inorganic content. Combustion temperature and phase, flaming or smoldering, play a secondary role in the water uptake of smoke. High–temperature ignition methods create flaming conditions that enhance hygroscopicity while lower–temperature smoldering conditions diminish hygroscopicity. Our results construct an empirical relation between κ neph and the inorganic content of the fuel and smoke to predict water uptake.

54 ENVIRONMENTAL SCIENCES↗

Performance properties of graphite reinforced composites with advanced resin matrices

The contribution of the resin matrix to the performance of the composite is studied with particular emphasis on the flammability, and thermal and mechanical properties. Of the several thermoset and thermoplastic matrices examined, the lowest fire-resistant properties of the composite have been observed with epoxy matrices. Bismaleimide A composites exhibit high fire-resistant properties, low moisture absorption, and good mechanical properties at 23 C. Bismaleimide B and phenolic retain their mechanical properties at elevated temperatures but have lower mechanical properties than the epoxy composites at ambient temperatures. Phenolic-novolac, polyethersulfone, and polyphenylsulfone composites exhibit high oxygen index and low smoke evolution.

Kourtides, D. A.↗