Search NASA⌕ Search

SEARCH · Search NASA

Results for “embedding technology”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

The Multiple Use Plug Hybrid for NanoSats (MUPHyN) Miniature Thruster

The Multiple Use Plug Hybrid (for) Nanosats is a prototype thruster is being developed to fill a niche application for NanoSat-scale spacecraft propulsion. When fully developed, the MUPHyN thruster will provide an effective and low-risk propulsive capability that could enable multiple NanoSats to be independently re-positioned after deployment from a parent launch vehicle. Because the environmentally benign, chemically-stable propellants are mixed only within the combustion chamber after ignition and the flow rate of the fuel is determined by a pyrolysis mechanism that is nearly independent of pressure or fuel grain defects, the system is inherently safe and can be piggy-backed near a secondary payload with little or no overall mission risk increase to the primary payload. The MUPHyN thruster uses safe-handling and inexpensive nitrous oxide (N2O) and acrylonitrile-butadiene-styrene (ABS) as propellants. Fused Deposition Modeling (FDM), a direct digital manufacturing process, is used to fabricate short-form-factor solid fuel grains with multiple helical combustion ports from ABS thermoplastic. This manufacturing process allows for the rapid development and manufacture of complex fuel grain geometries that are not possible to extrude or cast using conventional methods. This technology enables the construction of fuel grains with length-to-diameter ratios appropriate for incorporation into CubeSats while maintaining high surface areas and regression rates that allow the system to maintain a near optimal oxidizer to fuel ratio. The MUPHyN system provides attitude control torques by using secondary-injection thrust vectoring on a truncated aerospike nozzle. This configuration allows large impulse delta V burns and small impulse attitude control firings to be performed with the same system. To ensure survivability during extend duration burns, the MUPHyN incorporates a novel regenerative cooling design where the N2O oxidizer flows through a cooling path embedded in the aerospike nozzle before being injected into the combustion chamber near the nozzle base.

Eilers, Shannon D.↗
NASA NTRS1990

A distributed agent architecture for real-time knowledge-based systems: Real-time expert systems project, phase 1

We propose a distributed agent architecture (DAA) that can support a variety of paradigms based on both traditional real-time computing and artificial intelligence. DAA consists of distributed agents that are classified into two categories: reactive and cognitive. Reactive agents can be implemented directly in Ada to meet hard real-time requirements and be deployed on on-board embedded processors. A traditional real-time computing methodology under consideration is the rate monotonic theory that can guarantee schedulability based on analytical methods. AI techniques under consideration for reactive agents are approximate or anytime reasoning that can be implemented using Bayesian belief networks as in Guardian. Cognitive agents are traditional expert systems that can be implemented in ART-Ada to meet soft real-time requirements. During the initial design of cognitive agents, it is critical to consider the migration path that would allow initial deployment on ground-based workstations with eventual deployment on on-board processors. ART-Ada technology enables this migration while Lisp-based technologies make it difficult if not impossible. In addition to reactive and cognitive agents, a meta-level agent would be needed to coordinate multiple agents and to provide meta-level control.

Lee, S. Daniel↗
NASA NTRS2019

Gravity Effects in Two-Phase Microgap Flow

The high power density of emerging electronic devices is driving the transition from remote cooling, which relies on conduction and spreading, to embedded cooling, which extracts dissipated heat on-site. Two-phase microgap coolers employ the forced flow of dielectric fluids undergoing phase change in a heated channel within or between devices. Such coolers must work reliably in all orientations for a variety of applications (e.g., vehicle-based equipment), as well as in microgravity and high-g for aerospace applications, but the lack of acceptable models and correlations for orientation- and gravity-independent operation has limited their use. Reliable criteria for achieving orientation- and gravity-independent flow boiling would enable emerging systems to exploit this thermal management technique and streamline the technology development process. As a first step toward understanding the effect of gravity in two-phase microgap flow and transport, in an earlier effort, the authors studied the effects of evaporator orientation, mass flux, and heat flux on flow boiling of HFE7100 in a 1.01 mm tall by 13.0 mm wide by 12.7 mm long microgap channel. Orientation-independence, defined as achieving similar critical heat fluxes, heat transfer coefficients, and flow regimes across orientations, was achieved for mass fluxes of 400 kg/sq.m-s and greater (corresponding to a Froude number of about 0.8). In the present effort, the authors have studied the effects of gravity, mass flux, and subcooling on flow boiling of HFE7100 in a 0.17 mm tall by 13.0 mm wide by 12.7 mm long microgap channel. The Flow Boiling in Microgap Coolers payload experienced about three minutes of weightlessness and shorter periods of high-g (up to about 5 g) during two recent flights aboard the Blue Origin New Shepard reusable launch vehicle. The results from the flight experiments will be presented and compared with published criteria for achieving gravity-independence.

Robinson, Franklin L.↗
DOE OSTI2023

Study of The Compression of an Imploding Plasma and the Magnetic- Field Flux Using Advanced, Non-Intrusive, Spectroscopic Techniques

The main motivation of the project was to measure the magnetic field in pulsed power driven plasma compression using advanced non-intrusive spectroscopic techniques. The strength of the project is that it encompasses a combination of laboratory experiments with diagnostics for both the magnetic field and plasma properties and computational modeling. The following issues were addressed: (1) Plasma and magnetic field dynamics, (2) Field compression and diffusion, (3) Energy balance in the system, (4) Onset of instabilities, and (5) Correlation of the plasma and field evolutions with the initial conditions. The unique feature of the research was the use of advanced spectroscopy to measure both the magnetic field and various plasma properties in multiple locations using both side-on and end-on views, simultaneously. The experimental system allowed for imploding different gas mixtures (which facilitated local measurements) and for flexibility in modifying the initial conditions. Two current generators were used with significantly different current rise times (200 ns and 1.6 µs) but at the same current level of 400 kA. The slower pulsed power generator (at rise time 1.6 µs) was based at the Weizmann Institute of Science (WIS) and imploded plasma into which an axial magnetic field (up to 1 T) was initially embedded. The faster current rise time generator (at rise time 200 ns) based at University of California San Diego (UCSD) was used for plasma parameter studies initially, with collaborative efforts we successfully implemented the advanced spectroscopy techniques at UC San Diego. One graduate student (Nick Aybar) and a postdoctoral scholar (Maylis Dozeries) were trained. They both are based at the Lawrence Livermore National Laboratory now.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2017

Transparent Conductive Ink for Additive Manufacturing

NASA analyzes, tests, packages, and fabricates electrical, electronic, and electromechanical (EEE) parts. Nanotechnology is listed in NASA's Technology Roadmap as a key area to invest for further development.1 This research project focused on using nanotechnology to improve electroluminescent lighting in terms of additive manufacturing and to increase energy efficiency. Specifically, this project's goal was to produce a conductive but transparent printable ink that can be sprayed on any surface for use as one of the electrodes in electroluminescent device design. This innovative work is known as thick film dielectric electroluminescent (TDEL) technology. TDEL devices are used for "backlighting, illumination, and identification due to their tunable color output, scalability, and efficiency" (I.K. Small, T.D. Rolin, and A.D. Shields, "3D Printed Electroluminescent Light Panels," NASA Fiscal Year 2017 Center Innovation Fund Proposal, unpublished data, 2017). These devices use a 'front-to-back' printing method, where the substrate is the transparent layer, and the dielectric and phosphor are layered on top. This project is a first step in the process of creating a 3D printable 'back-to-front' electroluminescent device. Back-to-front 3D-printed devices are beneficial because they can be printed onto different substrates and embedded in different surfaces, and the substrate is not required to be transparent, all because the light is emitted from the top surface through the transparent conductor. Advances in this area will help further development of printing TDEL devices on an array of different surfaces. Figure 1 demonstrates the layering of the two electrodes that are aligned in a parallel plate capacitor structure (I.K. Small, T.D. Rolin, and A.D. Shields, "3D Printed Electroluminescent Light Panels," NASA Fiscal Year 2017 Center Innovation Fund Proposal, unpublished data, 2017). Voltage is applied across the device, and the subsequent electron excitation results in light emission at the top layer.

Patlan, X. J.↗
DOE OSTI2023

Elucidating the Role of Hydrogen Bonding in the Optical Spectroscopy of the Solvated Green Fluorescent Protein Chromophore: Using Machine Learning to Establish the Importance of High-Level Electronic Structure

Hydrogen bonding interactions with chromophores in chemical and biological environments play a key role in determining their electronic absorption and relaxation processes, which are manifested in their linear and multidimensional optical spectra. For chromophores in the condensed phase, the large number of atoms needed to simulate the environment has traditionally prohibited the use of high-level excited-state electronic structure methods. By leveraging transfer learning, we show how to construct machine-learned models to accurately predict the high-level excitation energies of a chromophore in solution from only 400 high-level calculations. Here, we show that when the electronic excitations of the green fluorescent protein chromophore in water are treated using EOM-CCSD embedded in a DFT description of the solvent the optical spectrum is correctly captured and that this improvement arises from correctly treating the coupling of the electronic transition to electric fields, which leads to a larger response upon hydrogen bonding between the chromophore and water.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Towards Immobilized Proton-Coupled Electron Transfer Agents for Electrochemical Carbon Capture from Air and Seawater

Electrochemical CO 2 separation has drawn attention as a promising strategy for using renewable energy to mitigate climate change. Redox-active compounds that undergo proton-coupled electron transfer (PCET) are an impetus for pH-swing-driven CO 2 capture at low energetic costs. However, multiple barriers hinder this technology from maturing, including sensitivity to oxygen and the slow kinetics of CO 2 capture. Here, we use vapor phase chemistry to construct a textile electrode comprising an immobilized PCET agent, poly(1-aminoanthraquinone) (PAAQ), and incorporate it into redox flow cells. This design contrasts with others that use dissolved PCET agents by confining proton-storage to the surface of an electrode kept separate from an aqueous, CO 2 -capturing phase. This system facilitates carbon capture from gaseous sources (a 1% CO 2 feed and air), as well as seawater, with the latter at an energetic cost of 202 kJ/mol CO2 , and we find that quinone moieties embedded within the electrode are more stable to oxygen than dissolved counterparts. Simulations using a 1D reaction-transport model show that moderate energetic costs should be possible for air capture of CO 2 with higher loadings of polymer-bound PCET moieties. The remarkable stability of this system sets the stage for producing textile-based electrodes that facilitate pH-swing-driven carbon capture in practical situations.

Ali, Fawaz↗
NASA NTRS2016

A Quantum-Assisted Algorithm for Sampling Applications in Machine Learning

An increase in the efficiency of sampling from Boltzmann distributions would have a significant impact in deep learning and other machine learning applications. Recently, quantum annealers have been proposed as a potential candidate to speed up this task, but several limitations still bar these state-of-the-art technologies from being used effectively. One of the main limitations is that, while the device may indeed sample from a Boltzmann-like distribution, quantum dynamical arguments suggests it will do so with an instance-dependent effective temperature, different from the physical temperature of the device. Unless this unknown temperature can be unveiled, it might not be possible to effectively use a quantum annealer for Boltzmann sampling. In this talk, we present a strategy to overcome this challenge with a simple effective-temperature estimation algorithm. We provide a systematic study assessing the impact of the effective temperatures in the learning of a kind of restricted Boltzmann machine embedded on quantum hardware, which can serve as a building block for deep learning architectures. We also provide a comparison to k-step contrastive divergence (CD-k) with k up to 100. Although assuming a suitable fixed effective temperature also allows to outperform one step contrastive divergence (CD-1), only when using an instance-dependent effective temperature we find a performance close to that of CD-100 for the case studied here. We discuss generalizations of the algorithm to other more expressive generative models, beyond restricted Boltzmann machines.

Perdomo-Ortiz, Alejandro↗
DOE OSTI2025

Electric Drive Technologies Consortium (EDTC)/ Cost competitive, high-Performance, highly Reliable (CPR) Power Devices on 4H-SiC (Final Report)

4H-Silicon carbide (4H-SiC) is a wide bandgap semiconductor that offers superior material properties over silicon, including higher critical electric field, thermal conductivity, and electron saturation velocity. These advantages make 4H-SiC highly attractive for high-voltage, high-efficiency power electronics. However, realizing the full potential of SiC requires device technologies that are not only high-performing but also manufacturable and reliable under real-world operating conditions. This report summarizes the outcomes of a five-year R&D effort funded by the U.S. Department of Energy (DOE) under the Electric Drive Technologies Consortium (EDTC), focused on developing cost-competitive, high-performance, and highly reliable (CPR) power devices on 4H-SiC substrates. The program targeted scalable and manufacturable 1.2 kV-class SiC MOSFETs optimized for next-generation electric vehicles, renewable energy systems, and industrial power conversion. The project delivered transformative advancements in SiC power device performance and ruggedness. Particularly, Specific on-resistance (R on,sp ) was reduced by up to 37%, from ~4.0 m$\Omega \cdot$cm 2 in earlier designs to an industry-leading 2.40 m$\Omega \cdot$cm 2 , driven by optimized doping, refined JFET widths, and layout engineering. Breakdown voltages (BV) exceeded 1600 V, marking improvement over legacy baselines, and demonstrating the robustness of newly implemented junction profiles and edge terminations. Short-circuit withstand time (SCWT) saw a remarkable 4$\times$ increase, from ~2 $\mu$s to over 8 $\mu$s, achieved through the successful deployment of deep P-well structures (~1.8–2.0 $\mu$m) via channeling implantation. This innovative process breakthrough enabled precise junction formation without MeV-class implantation tools, reduced leakage under high field stress, and allowed even the shortest-channel devices (down to 0.3 $\mu$m) to achieve both high BV and excellent ruggedness—breaking the traditional trade-off between conduction efficiency and blocking capability. Several novel architectures pushed the performance envelope further. JBSFETs—featuring embedded Schottky portions—eliminated bipolar degradation and drastically reduced third-quadrant leakage, while Ladder MOSFETs introduced a clever orthogonal conduction path that achieved a 15.4% reduction in R on,sp over standard linear designs. Switching performance reached new benchmarks: short-channel devices showed a 31% reduction in total switching energy compared to 0.5 $\mu$m counterparts, while maintaining manageable gate drive requirements. Layout-optimized structures not only improved transconductance but also accelerated switching transitions, pointing to real-world benefits in converter-level efficiency. The devices also passed rigorous reliability validation. Stress-tested across TDDB, HTGB, HTRB, HVP, and burn-in, the devices screened under 30 V/10 hr and 43 V/1 s protocols consistently exhibited tighter lifetime distributions and long-term oxide robustness. These screening techniques proved effective in identifying latent defects and ensuring deployment-grade reliability. Meanwhile, advanced 3D TCAD simulations revealed and resolved electric field hotspots—particularly in HEXFET corners—where fields exceeding 4.8 MV/cm were mitigated through geometry-aware layout corrections. Overall, the results of this project demonstrate a manufacturable and scalable SiC power device platform that addresses key DOE performance targets for efficient, robust, and reliable 1.2kV 4H-SiC Power Devices. The developed technologies represent a meaningful step forward in the commercial readiness of high-voltage SiC solutions and provide a strong foundation for continued advancement in wide bandgap power electronics.

42 ENGINEERING↗
DOE OSTI2020

Plasma and X-ray radiation-induced damage mechanisms in a tungsten heavy alloy

Tungsten-based materials are among the main candidate plasma-facing materials for future fusion reactors where extreme conditions of thermomechanical stresses, radiation, and energetic particles must be withstood. Here a hybrid X-pinch platform combined with a pulsed power machine was used to study damage mechanisms in 90W–4Cu–6Ni tungsten heavy alloy as a result of exposure to high energy density plasma, X-ray radiation, and the resulting thermal shock. It was found that the plasma-facing surface of the material undergoes severe melting and ablation with the extent of ablation being higher in the Cu–Ni phase than the W particles. Rapid melting and solidification transform the W particles into fine dendrite morphologies embedded in the Cu–Ni solid solution. Cracking was also observed in the subsurface layers at the interfaces between the W particles and the Cu-rich phase of the Cu–Ni matrix. X-ray radiation, on the other hand, cause slight melting on the surface without significant ablation and no cracking.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Moisture Absorbing and Water Self‐Releasing from Hybrid Hydrogel Desiccants

Abstract Atmospheric moisture is a valuable resource for fresh water and potentially sustainable energy. However, direct harvesting water from moisture (the vapor form) remains the most challenging. Hybrid desiccants made from hydrogels embedded with salt offer promise in absorbing moisture. However, the desorption process often requires additional energy to heat the samples. Here, poly(acrylic acid) (PAA) hydrogels embedded with lithium chloride are prepared, demonstratng simultaneous moisture absorption and self‐release of liquid water at room temperature with 50–90% relative humidity. The water self‐releasing process can be separated into two distinct stages: 1) surface release, where water droplets grow on the hydrogel surface due to differences in nucleation and diffusion rates, and 2) bulk release, triggered by the collapse of polymer chains, subsequently releasing water from the hydrogel network. Factors such as salt concentration, hydrogel crosslinking density, and film thickness are investigated to better understand the moisture absorption and water‐releasing processes. Moreover, hydrophobic domains are introduced onto the salt‐embedded PAA films, creating an edge effect that enhances the droplet growth rates. When the hydrophobic domains are patterned, the movement of released water can be guided, resulting in a threefold increase in water removal rate attributed to gravitational force.

Chemistry↗
NASA NTRS2016

SAFEGUARD: An Assured Safety Net Technology for UAS

As demands increase to use unmanned aircraft systems (UAS) for a broad spectrum of commercial applications, regulatory authorities are examining how to safely integrate them without loss of safety or major disruption to existing airspace operations. This work addresses the development of the Safeguard system as an assured safety net technology for UAS. The Safeguard system monitors and enforces conformance to a set of rules defined prior to flight (e.g., geospatial stay-out or stay-in regions, speed limits, altitude limits). Safeguard operates independently of the UAS autopilot and is strategically designed in a way that can be realized by a small set of verifiable functions to simplify compliance with regulatory standards for commercial aircraft. A framework is described that decouples the system from any other devices on the UAS as well as introduces complementary positioning source(s) for applications that require integrity and availability beyond what the Global Positioning System (GPS) can provide. Additionally, the high level logic embedded within the software is presented, as well as the steps being taken toward verification and validation (V&V) of proper functionality. Next, an initial prototype implementation of the described system is disclosed. Lastly, future work including development, testing, and system V&V is summarized.

Dill, Evan T.↗
NASA NTRSDate not supplied

XRF Characterization of MMOD Impact Damage

Introduction The Hypervelocity Impact Technology (HVIT) Group at the NASA Johnson Space Center (JSC) has performed over 150 post flight MMOD inspections on returned space-ex-posed hardware and collected over 1,600 samples. Determination of the impactor source typically requires an analysis of the projectile residue in the damage feature. At this time, about 20% of the samples have been processed. Types of Samples Samples in the HVIT group collection can be classified into two types. Indirect (non-destructive) samples are produced when a pliable material (e.g., adhesive tape or dental mold) is inserted into an impact feature. With this type of sampling technique, crater material and (hopefully) projectile residue material is embedded in the sample media and can detected using further chemical characterizing techniques. Direct (destructive) sampling involves the in-tact extraction of material from the spacecraft and is done in a manner that the entire impact feature can be excised intact. This technique provides the greatest chance of successfully determining impactor source due to the entirety of the projectile remnants being present within the collected sample. Updated Projectile Residue Detection Techniques Previous assessments of projectile provenance have involved the use of samples that are first mounted in epoxy, sectioned to expose the crater interior, imaged with a scanning electron microscope (SEM), then any observed impactor residue was then analyzed using an energy dispersive spectrometer (EDS). This technique, while proven, may be supplemented with other types of elemental analysis techniques that can observe major element chemistry, in order to improve throughput of sample analysis. The Astromaterials Research and Exploration Science (ARES) Division at JSC, for example, operates a Bruker M4 Tornado micro-X-Ray fluorescence (XRF) spectrometer, capable of creating elemental maps of areas around these small impact features in a couple of hours, with a spot size <20 μm. The potential advantage with this technique lies in sample preparation, as no polishing or conductive coatings are needed. Early trials attempted to deter-mine impactor composition by collecting spectra from intact samples by aiming the X-Rays directly into the impact feature, but the signal:noise ratio was too low for confident material identification. Sample preparation for XRF then relies on sectioning the samples parallel to the impactor trajectory in order to expose the largest area of subsurface damage possible, thus maximizing the signal from any small impactor remnants. Complementary to the use of XRF for sample analysis, ARES also houses a Nikon XTH 320 micro-X-Ray computed tomography (XCT). This instrument can be used to create 3D visualizations of impact damage for the determination of crater volumes and dimensions, as well as for the determination of the best place to section each sample for the subsequent XRF analysis.

J L Hyde↗
DOE OSTI2023

Machine learning based simultaneous control of air handling unit discharge air and condenser water temperatures set-point for minimized cooling energy in an office building

In this study, an artificial intelligence based real-time prediction and control model to optimize condenser water temperature and discharge air temperature (DAT) set-points in water-cooled air handling unit (AHU) system has been developed. EnergyPlus-MATLAB co-simulation has been conducted to analyze the developed model's effectiveness. Here, to develop artificial neural networks (ANN) model, embedded neural network objects in MATLAB was utilized. The developed model could decide an optimal temperature set-points based on outdoor air wet-bulb temperature to reflect the Korean climate context. As a result, the developed ANN prediction model showed the predictive performance of Cv(RMSE) of approximately 21%. Compared to the conventional fixed temperature algorithm, which fixes AHU DAT at 14°C and condenser water temperature at 32°C, the ANN based optimized control showed a 22% total cooling energy reduction. These results show that significant energy savings can be achieved by simultaneously controlling condenser water temperature and AHU DAT set-points considering Korean climatic characteristics using AI technologies such as ANN models.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2020

An Adaptive Reference Scheme to Extend the Functional Range of Optical Backscatter Reflectometry in Extreme Environments

Optical frequency domain reflectometry (OFDR) measurements are performed by recording the interference pattern of light backscattered by density fluctuations or Bragg gratings along the length of an optical fiber. Changes in local temperature or strain in the fiber cause shifts in the backscattered light spectrum, which can be calibrated to the applied temperature or strain. Comparing the backscattered optical spectra from each reflection site with a reference (unstrained) spectrum allows for quantification of local spectral shifts. While mature OFDR-based technologies can provide high-precision spatially distributed measurements over kilometer lengths, the post-processing approaches used to recover spectral shifts from raw optical intensity data can limit the use of OFDR in harsh environments. This paper presents a novel approach to post-processing OFDR data which extends the usability of optical fibers exposed to harsh environments. This approach is the first to use the spectral shift quality, calculated for two OFDR measurements, to identify an appropriate reference scan from which the spectral shift can be determined. Here, three experimental data sets are used to test the algorithm: (1) an optical fiber heated to >950°C, (2) an aluminum-embedded optical fiber under strain from differential thermal expansion, and (3) an optical fiber exposed to a total neutron flux of 2×10 13 n/cm 2 /s over 40 hours in a nuclear test reactor. Results show that using a metric of quality to select an appropriate reference measurement extends the functional range of OFDR strain and temperature sensors. Furthermore, this algorithm can be applied to existing OFDR data.

47 OTHER INSTRUMENTATION↗
NASA NTRSDate not supplied

Protective Coatings for Mitigating Lunar Dust Abrasion and Adhesion

Materials resistant to the harsh lunar environment are needed to support long duration, sustainable missions on the Moon’s surface. Lunar dust poses a significant threat to the durability of components and vehicles due to its fine, jagged morphology and highly abrasive nature. These characteristics result in particles eroding, adhering and/or embedding onto component surfaces and into device confined geometries (e.g., gear housing, interlocking systems, etc.) potentially leading to premature failure. The aim of this work is to identify and characterize wear-resistant materials, including advanced ceramics, for use as protective coatings to minimize abrasion and adhesion caused by lunar dust. Results from testing and evaluation methods devised to elucidate and mimic aspects of lunar dust degradation, including adhesion, abrasion and erosion, as well as the lunar environment, will be presented. Discussion on balancing the need for dust management and tolerance versus dust adhesion mitigation will be shared in context of relevant lunar applications within the NASA Lunar Occupancy Dust Surface Separation Technologies effort, which is part of a NASA-wide effort to enable a sustained lunar presence through the Lunar Surface Innovation Initiative.

lunar dust mitigation↗
DOE OSTI2025

Conditional guide RNA deactivation by mRNA and small molecule triggers in Saccharomyces cerevisiae

CRISPR interference (CRISPRi) technologies have revolutionized bioengineering by providing precise tools for gene expression modulation, enabling targeted gene perturbation and metabolic pathway optimization. Despite these advances, achieving dynamic control over gene expression by CRISPR-based regulation remains a challenge due to its inherently static nature. Utilizing toehold-mediated strand displacement and ligand-responsive ribozymes (aptazymes), this study introduces switchable guide RNAs (gRNAs) that facilitate tunable gene expression mediated by mRNA or small molecule signals. We demonstrate complete silencing of gRNA via strategically designed 5’ or 3’ extensions that impede the gRNA spacer or the dCas9 handle, with subsequent restoration of function through sequestration or cleavage of the obstructive sequence. The resulting toehold-embedded or aptazyme-embedded gRNAs can be deactivated by specific signals, including two full-length translatable mRNAs and two small molecule triggers, thereby lifting CRISPRi repression on targeted genes. This modular approach allows for gRNA-based biocomputing through multi-layer or multi-input genetic logic gates in Saccharomyces cerevisiae . Offering a versatile strategy for post-CRISPR regulation in response to environmental signals or cellular states, this methodology expands the toolkit in eukaryotic systems for reversible control of gene expression.

Aptazyme↗
DOE OSTI2022

Performance of Microreactor Test Article with Embedded Sensors During Testing in The Single Primary Heat Extraction and Removal Emulator

The nuclear industry is pursuing microreactors that can be factory assembled and deployed to remote regions for reliable power generation. One class of microreactors uses a monolithic metal core block coupled to heat pipes that use passive heat flow, increasing the surface area for heat transfer without requiring active coolant flow through the reactor core. Additional experimental testing is required to understand the heat rejection limitations of heat pipes and thermal stresses in the monolithic core block due to significant temperature gradients. This report describes the initial characterization and testing of a stainless-steel test article that was fabricated with embedded sensors to measure heat pipe performance limits, as well as spatially distributed temperatures and strains during electrically heated thermal testing to simulate nuclear heating. The electrically heated testing was performed in the Single Primary Heat Extraction and Removal Emulator facility located at Idaho National Laboratory. The ultimate goals of this work are to (1) accurately monitor temperature and strain distributions that result from differential thermal expansion in the test articles and (2) quantify the heat rejection limits of heat pipes as a function of operating temperature and working fluid during steady-state and transient operations. Initial tests focused on the feasibility of using advanced fiber-optic sensors and other sensor technologies to improve the understanding of temperature and strain distributions within the electrically heated experiments. However, these sensing capabilities could benefit the broader microreactor community if the sensors could be used to monitor component and system health during nuclear operations to inform a limited number of microreactor operators, ultimately reducing operation and maintenance costs and moving toward semiautonomous operation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗