Search NASA⌕ Search

SEARCH · Search NASA

Results for “high gradient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Optimal surface-tension isotropy in the Rothman-Keller color-gradient lattice Boltzmann method for multiphase flow

The Rothman-Keller color-gradient (CG) lattice Boltzmann method is a popular method to simulate two-phase flow because of its ability to deal with fluids with large viscosity contrasts and a wide range of interfacial tensions. Here, two fluids are labeled red and blue, and the gradient in the color difference is used to compute the effect of interfacial tension. It is well known that finite-difference errors in the color-gradient calculation lead to anisotropy of interfacial tension and errors such as spurious currents. Here, we investigate the accuracy of the CG calculation for interfaces between fluids with several radii of curvature and find that the standard CG calculations lead to significant inaccuracy. Specifically, we observe significant anisotropy of the color gradient of order 7% for high curvature of an interface such as when a pinchout occurs. We derive a second order accurate color gradient and find that the diagonal nearest neighbors can be weighted differently than in the usual color-gradient calculation such that anisotropy is minimized to a fraction of a percent. The optimal weights that minimize anisotropy for the smallest radius of curvature interface are found to be w = (0.298, 0.284, 0.275) for diagonal nearest neighbors for the cases of the interface smoothing parameter β = (0.5, 0.7, 0.99), somewhat higher than the w = 0.25 value derived by Leclaire et al. [Leclaire, Reggio, and Trepanier, Computers and Fluids 48, 98 (2011)] based on obtaining isotropic errors to second order. We find that use of these optimal w values yields over a factor of 10 decrease in anisotropy and over a factor of 30 decrease in mean anisotropy relative to using the standard w = 1 value. And we find a factor of about 2 decrease in the anisotropic error and up to factor 15 decrease in mean anisotropic error relative to the choice of w = 0.25 for small radius of curvature interfaces. The improved CG calculations will allow the method to be more reliably applied to studies of phenomenology and pore scale processes such as viscous and capillary fingering, and droplet formation where surface-tension isotropy of narrow fingers and small droplets plays a crucial role in correctly capturing phenomenology. We present an example illustrating how different phenomena can be captured using the improved color-gradient method. Namely, we present simulations of a wetting fluid invading a fluid filled pipe where the viscosity ratio of fluids is unity in which droplets form at the transition to fingering using the improved CG calculations that are not captured using the standard CG calculations. We present an explanation of why this is so which relates to anisotropy of the surface tension, which inhibits the pinchouts needed to form droplets.

58 GEOSCIENCES↗
DOE OSTI2026

Achievement of a high-density, high-confinement, and high-beta tokamak plasma regime in DIII-D, and implications for a lower-current path for ITER and FPP

Experiments on DIII-D have demonstrated a density-confinement synergy that enables sustainment of high performance in a previously unattained parameter regime of simultaneous very high energy confinement quality (H 98y2 ≥ 1.5), very high line-average density Greenwald fraction (ƒ Gr = πa 2 < n >/I P ≥ 1.4), and high toroidal beta (β T ≥ 3%). Tokamak operation in this regime is essential for a compact steady-state FPP, as well as for Q=10 with 500 MW of fusion power in ITER at I P << 15 MA. These experiments leveraged the knowledge that, in the high-poloidal-beta (β P ) regime, impurity and density gradients can enhance turbulence stabilization caused by high α MHD (α MHD ~(dβ P )⁄dr). This was described by theoretical predictions and gyrokinetic transport simulations [M.T. Kotschenreuther et al, 2024 Nucl. Fusion, 64 076033], and later confirmed by experiments on DIII-D [S. Ding et al, 2024 Nature 629 555]. To increase both β P and β T , the new experiments increased the ideal-wall stability β N -limit by using a smaller plasma-outer wall distance and higher triangularity in the plasma cross section (top/bottom average δ~0.9), enabled by the recent “shape & volume rise” (SVR) modification to the DIII-D divertor. The higher triangularity also contributed to achieving higher ƒ Gr by enabling higher pedestal density. At high density, the pedestal is ballooning limited and exhibits small and frequent ELMs, while the divertor is near detachment even without any impurity seeding. High plasma performance was attained and sustained reproducibly, with the eventual terminations brought about by an MHD mode destabilized as the current profile slowly continued to evolve. A path to stationary fully noninductive operation might include ECH injection to reduce both core impurity accumulation and the electron collisionality, thus increasing the bootstrap current. These experiments provide the first experimental demonstration of the ƒ Gr , H 98y2 , and β T values required simultaneously for ITER Q = 10 at I P < 10 MA, pointing to practical ways to improve the energy confinement in a fusion reactor.

Garofalo, Andrea M. [General Atomics, San Diego, C↗
NASA NTRS1989

A numerical study of scalar gradients in Kelvin-Helmholtz billows

A high resolution numerical technique is used to model the development of a periodically perturbed shear layer imbedded in an initially vertical gradient of a passive scalar. The technique follows the development of the vorticity through an initial linear growth state and well into the nonlinear development of Kelvin-Helmholtz billows, in the zero-viscosity, zero-diffusion limit. The resulting scalar distribution rapidly develops regions of extremely sharp scalar gradients, which wind around the periodically spaced vortical low gradient cores. Vertical cross sections through different parts of the billow structure are presented and compared with rocket measurements of electron density fine structure in the mesosphere. Gradient limits imposed by finite diffusion are calculated, and implications for atmospheric radar observations are discussed.

Parker, J. W.↗
DOE OSTI2022

Wildfire-dependent changes in soil microbiome diversity and function

Abstract Forest soil microbiomes have crucial roles in carbon storage, biogeochemical cycling and rhizosphere processes. Wildfire season length, and the frequency and size of severe fires have increased owing to climate change. Fires affect ecosystem recovery and modify soil microbiomes and microbially mediated biogeochemical processes. To study wildfire-dependent changes in soil microbiomes, we characterized functional shifts in the soil microbiota (bacteria, fungi and viruses) across burn severity gradients (low, moderate and high severity) 1 yr post fire in coniferous forests in Colorado and Wyoming, USA. We found severity-dependent increases of Actinobacteria encoding genes for heat resistance, fast growth, and pyrogenic carbon utilization that might enhance post-fire survival. We report that increased burn severity led to the loss of ectomycorrhizal fungi and less tolerant microbial taxa. Viruses remained active in post-fire soils and probably influenced carbon cycling and biogeochemistry via turnover of biomass and ecosystem-relevant auxiliary metabolic genes. Our genome-resolved analyses link post-fire soil microbial taxonomy to functions and reveal the complexity of post-fire soil microbiome activity.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Confinement in electron heated plasmas in Wendelstein 7-X and ASDEX Upgrade; the necessity to control turbulent transport

In electron (cyclotron) heated plasmas, in both ASDEX Upgrade (L-mode) and Wendelstein 7-X, clamping of the ion temperature occurs at $T_\mathrm{i}$ ~ 1.5 keV independent of magnetic configuration. The ions in such plasmas are heated through the energy exchange power as ${n}_{\mathrm{e}}^{2}({T}_{\mathrm{e}}-{T}_{\mathrm{i}})/{T}_{\mathrm{e}}^{3/2}$, which offers a broad ion heating profile, similar to that offered by alpha heating in future thermonuclear fusion reactors. However, the predominant electron heating may put an additional constraint on the ion heat transport, as the ratio $T_\mathrm{e}T_\mathrm{i}$ > 1 can exacerbates ITG/TEM core turbulence. Therefore, in practical terms the strongly 'stiff' core transport translates into Ti-clamping in electron heated plasmas. Due to this clamping, electron heated L-mode scenarios, with standard gas fueling, in either tokamaks or stellarators may struggle to reach high normalized ion temperature gradients required in a compact fusion reactor. The comparison shows that core heat transport in neoclassically optimized stellarators is driven by the same mechanisms as in tokamaks. The absence of a strong H-mode temperature edge pedestal in stellarators, sofar (which, like in tokamaks, could lift the clamped temperature-gradients in the core), puts a strong requirement on reliable and sustainable core turbulence suppression techniques in stellarators.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Pressure Modification or Barrier Issues during Polymer Flooding Enhanced Oil Recovery

Effective oil displacement from a reservoir requires adequate and properly directed pressure gradients in areas of high oil saturation. If the polymer bank is too large or too viscous during a polymer flood, the pressure drops from the injection well to the polymer front may act as a pressure modification or barrier by usurping most of the downstream driving force for oil displacement. Polymer injection pressures must be limited. The maximum allowable injection pressure is commonly constrained by caprock integrity, injection equipment, and/or regulations, even though fractures can be beneficial to polymer injectivity. This paper examines when the pressure-barrier concept limits the size and viscosity of the polymer bank during a polymer flood. Analytical and numerical methods are used to address this issue. We examine the relevance of the pressure modification concept for a wide variety of circumstances, including oil viscosities ranging from 10 cp to 1650 cp, vertical wells versus horizontal wells, single versus multiple layered reservoirs, permeability contrast, and crossflow between layers. We also examine the relation between the pressure-barrier concept and fractures and fracture extension during polymer injection. We demonstrate that in reservoirs with single layers, the pressure-barrier concept only limits the optimum viscosity of the injected polymer if the mobility of the polymer bank is less than the mobility of the displaced oil bank. The same is true for multizoned reservoirs with no crossflow between layers. Thus, for these cases, the optimum polymer viscosity is likely to be dictated by the mobility of the oil bank, unless other factors intervene. For multizoned reservoirs with free crossflow between layers, the situation is different. A compromise must be reached between injected polymer viscosity and the efficiency of oil recovery. This work is particularly relevant to viscous oil reservoirs where polymer viscosities are substantially lower than the oil viscosity.

58 GEOSCIENCES↗
DOE OSTI2024

Comparative analysis of nutrient concentrations in generalist and specialist tree species and soils, Manaus, Brazil

This dataset was collected near Manaus, Brazil, at ZF-2 site, inside the North-South transect plots from 20221011 to 20221020. Measurements were made on specialists and generalist tree species along topographic gradient (in upland high-clay content soils of plateaus and high sandy content and partially flooded soils of valleys). We selected nine species (with four replicates each, totaling 35 individuals) occurring in different topographic positions: three plateau specialists, three valley specialists, and three generalists, where leaf and trunk samples were collected from each individual, and soil samples for carbon and nutrient analysis and quantification. Three soil pits were opened around each sample tree, about one meter apart (total of 105 soil pits each 60-cm deep), where soil samples were collected at four depths: 0-5, 5-10, 10-30 and 30-50 cm. In each of the three pits around each tree, one single sample was taken at each depth and combined to obtain a composite sample per depth per individual tree (35 trees × 4 depths = 140 soil samples). The files “Plant_Nutrient_Concentrations_NS_Transect_Manaus.csv” and “Soil_Nutrient_Concentrations_NS_Transect_Manaus.csv” contain the nutrient concentration data from plant and soil material, respectively. Additionally, the file “Sample_Info.csv” contains details about each variable including units and data type. The file “Species_Info.csv” includes information about each sampled individual, such as species, family, diameter at the breast height (DBH), and more. The dataset is ready to be used in any programming language like python or R. This dataset was originally published on the NGEE Tropics Archive and is being mirrored on ESS-DIVE for long-term archival Acknowledgement: Funding for NGEE-Tropics data resources was provided by the U.S. Department of Energy Office of Science, Office of Biological and Environmental Research.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Pressure Barrier Applicability to Polymer Flood Design

Effective oil displacement from a reservoir requires adequate and properly directed pressure gradients in areas of high oil saturation. If the polymer bank is too large or too viscous during a polymer flood, the pressure drop from the injection well to the polymer front may act as a pressure barrier by usurping most of the downstream driving force for oil displacement. Polymer injection pressures must be limited. The maximum allowable injection pressure is commonly constrained by caprock integrity, injection equipment, and/or regulations, even though fractures can be beneficial to polymer injectivity (and even sweep efficiency in some cases). This paper examines when the pressure-barrier concept limits the size and viscosity of the polymer bank during a polymer flood. Both analytical and numerical methods are used to address this issue. We examine the relevance of the pressure barrier concept for a wide variety of circumstances, including oil viscosities ranging from 10-cp (like at Daqing, China) to 1650-cp (like at Pelican Lake, Alberta), vertical wells (like at Tambaredjo, Suriname) versus horizontal wells (like at Milne Point, Alaska), single versus multiple layered reservoirs, permeability contrast, and with versus with crossflow between layers. We also examine the relation between the pressure-barrier concept and fractures and fracture extension during polymer injection. We demonstrate that in reservoirs with single layers, the pressure-barrier concept only limits the optimum viscosity of the injected polymer if the mobility of the polymer bank is less than the mobility of the displaced oil bank. The same is true for multi-zoned reservoirs with no crossflow between layers. Thus, for these cases, the optimum polymer viscosity is likely to be dictated by the mobility of the oil bank, unless other factors (like fracture extension) intervene. For multi-zoned reservoirs with free crossflow between layers, the situation is different. A compromise must be reached between injected polymer viscosity and the efficiency of oil recovery. The relevance of our findings is applied to operations for several existing polymer floods. This work is particularly relevant to viscous-oil reservoirs (like Pelican Lake and others) where the injected polymer viscosities are substantially lower than the oil viscosity

Wang, Dongmei↗
DOE OSTI2022

High Performance Computing to Quantify the Evolution of Microscopic Concentration Gradients During Flash Processing

During the Flash process, the cross section of a plain-carbon or a low-alloy steel is austenitized through rapid heating and transformed on rapid cooling to a predominantly martensite + bainite structure with small amounts of retained austenite. Unlike conventional heat treating, homogeneity is intentionally avoided during Flash processing of steels. The Flash process assembly consists of a pair of rolls that transfer the steel sheets through the heating and cooling stage of the thermal cycle. The initial microstructure of the steel consists of ferrite (body-centered cubic iron) + carbide ((Fe,X)mCn) mixture. The heating rate through the peak temperature is a function of temperature and reaches a peak of about 300-400°C/s and the cooling rate has a maximum value of 3,000-4,000°C/s. The on-heating phase transformations include carbide dissolution, austenite (face-centered cubic iron) nucleation and growth, and diffusion of carbon and other substitutional elements in the steel. The on-cooling phase transformations include formation of martensite (body-centered tetragonal phase containing supersaturated solute) and bainite (ferrite plates with or without fine carbides). In this project, the focus is on Fe-C-Cr steels that are currently Flash processed for armor applications. The modeling effort proposed here will help optimize the Flash thermal cycle for these low alloy steels to achieve the target performance, which is an ongoing effort at SFP Works. A significant feature of Flash processed Fe-C-Cr steels is the presence of scatter in the through-thickness in the sheet. The variability in hardness results from a variability in the bainite + martensite microstructure that is sensitive to the local chemical concentration of C and Cr. Such a chemical inhomogeneity is intentionally obtained in the Flash process. Although such a microstructural gradient is presumably responsible for the exceptional properties of the Flash processed steel, it is very important to quantify the gradients as a function of Flash variabilities in processing parameters and the input microstructure. Understanding the mechanistic pathway that leads to microstructural gradients could be ground-breaking and instrumental for achieving better process control and optimized microstructural state to meet application-specific strength-ductility requirements. Since the final microstructure depends on setting up precise solute concentration gradients through a rapid heating process, and transforming these regions into various phases, it is important to understand how small changes in steel chemistry, input microstructure (carbide size and distribution), and process variables (Flash thermal cycle) will impact the solute concentration gradients.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1970

Rugged, low-conductance, heat-flow probe

Lightweight, compact probe structure has low thermal conductance to enable accurate measurement of slight temperature gradients. Probe combines ruggedness, high precision, accuracy, and stability. Device can withstand vibration, shock, acceleration, temperature extremes, and high vacuums, and should interest industrial engineers and geologists.

Boudreau, E. J.↗
NASA NTRS1981

Structural analysis of cylindrical thrust chambers, volume 2

Analytical results are presented which predict cumulative plastic deformation characteristic of damage observed in coolant channel walls of regeneratively cooled rocket thrust chambers. The damage consists of bulging and plastic flow which leads to thinout and rupture of the channel wall under the combined effects of high pressures, high temperatures and temperature gradients experienced during cyclic firings of actual test chambers. Analytical predictions correlate with test results.

Armstrong, W. H.↗
NASA NTRS1982

Observations of solar flare transition zone plasmas from the Solar Maximum Mission

The spatial and temporal evolution of the Si IV and O IV intensity, density and mass motions in preflare and flare transition zone plasmas are studied for the case of the April 8, 1980 flare. It is found that: (1) the UV flare observed in the Si IV and O IV lines is unambiguously identified as occurring in a low-lying, preexisting transition zone loop which spanned the magnetic neutral line separating a larger leader spot and a newly emerged, isolated spot of opposite polarity; (2) at the onset of the flare, the easternmost footpoint, which was anchored in an isolated spot region of high longitudinal magnetic field gradient, showed sudden, impulsive brightening with large intensity increases; and (3) the release flare energy was transported by way of large-scale connecting field lines to other parts of the active region, producing the hot plasma and H-alpha kernels observed near the trailing spot.

Cheng, C.-C.↗
NASA NTRS1985

Thrust chamber life prediction

The reusable life of the Space Shuttle main engine (SSME) is influenced by the cyclic life of the regeneratively liquid cooled main combustion chamber (MCC). During an operational duty cycle the MCC liner is subjected to a large transient thermal gradient that imparts a high thermal cyclic strain to the liner hot gas wall. Life predictions of such chambers have usually been based on low cycle fatigue (LCF) evaluations. Hot-fire testing, however, has shown significant mid-channel wall deformation and thinning during accrued cyclic testing. This phenomenon is termed cyclic creep and appears to be significantly accelerated at elevated temperatures. An analytical method that models the cyclic creep phenomenon and its application to thrust chamber life prediction is presented. The chamber finite element geometry is updated periodically to account for accrued wall thinning and distortion. Failure is based on the tensile instability failure criterion. Cyclic life results for several chamber life enhancing coolant channel designs are compared to the typically used LCF analysis that neglects cyclic creep. The results show that the usable cyclic creep life is approximately 30 to 50% of the commonly used LCF life.

Kasper, H. J.↗
NASA NTRS1985

Density response of neutral atmospheric layers to gravity wave perturbations

Expressions for the density response of neutral atmospheric layers to propagating waves are derived. The expressions include nonlinear effects and are used to compute the response of the mesospheric sodium layer to low-frequency internal gravity waves. The results are compared with lidar observations of the sodium layer and used to deduce gravity wave parameters. It is shown that because of the large sodium density gradients and the relatively high amplitudes of gravity waves at mesospheric heights the nonlinear components of the layer density response must be considered in interpreting sodium lidar data.

Gardner, C. S.↗
NASA NTRS1985

High-speed compressible flow and other advection-dominated problems of fluid dynamics

Finite element methods are described for modeling high speed compressible flows with strong advection, problems important to aerodynamics. The situations are characterized by high pressure and temperature gradients, transients and the appearance of discontinuities, factors which require mesh refinement during computations. Techniques are developed for temporal and spatial discretization of a model problem. Several observations are made regarding the explicit and implicit features of the calculations, the use of the Lax-Wendroff scheme to produce a mass-matrix for obtaining accurate results for transients, methods of performing stability analyses, and simplification techniques. Examples are provided of solving the nonlinear shallow-water equations and describing compressible flows, particularly transonic flows. Domain splitting is defined for improving the calculations at each time step and in different parts of the flow regime while simultaneously advancing the calculations towards a solution.

Zienkiewicz, O. C.↗
NASA NTRS1986

Temperature-plant pigment-optical relations in a recurrent offshore mesoscale eddy near Point Conception, California

The temperature-plant pigment-optical structure of a mesoscale anticyclonic eddy consistently found in shipboard surveys and satellite-sensed data several hundred kilometers southwest of Point Conception, CA, is described on three different time scales (100-day mesoscale, annual, and several-year). The satellite coastal zone color scanner (CZCS) ocean color imagery detected the near-surface chlorophyll structure of the eddy, but in situ optical and plant pigment data suggest that such imagery does not provide a good estimate of the integrated chlorophyll field of the eddy. The temperature and plant pigment boundaries of the eddy, as determined from two-dimensional gradients of advanced very high resolution radiometer (AVHRR) and CZCS imagery, do not coincide spatially. This and in situ temperature, plant pigment, and optical structure provide additional evidence that some eddy systems in the California Current are not isolated vortex systems but rather continuously entrain waters of nonlocal origin laterally into their upper layers. Within the California Current a ratio of AVHRR/CZCS data is useful for separating inshore from oceanic water masses and following their surface entrainment by offshore vortices. The historical 28-year California Cooperative Oceanic Fisheries Investigations data for the Point Conception region of the California Current and remotely sensed data over this region show that the Point Conception eddy is a recurrent feature in the offshore California Current. Moreover, the available data provide evidence that a large number of warm-core mesoscale eddies occur simultaneously in a transition zone between coastal and oceanic regimes, that these features recur at preferred locations within the transition zone, and that this family of eddies should impose a significant offshore boundary condition on the flow of the California Current.

Simpson, James J.↗
NASA NTRS1988

Elevated temperature crack growth

The problem of crack growth in hot path components such as combustor liners is complicated by several practical and theoretical considerations. The loading environment of such components involves high temperature levels and gradients that lead to considerations such as thermal stresses, crack closure, hold time, inelastic strains (both time dependent and independent), and Thermal Mechanical Fatigue (TMF). In general, a good understanding of the influence of these factors on crack growth was not obtained. At the same time, several nonlinear fracture mechanics parameters were suggested for such applications; however, most of the proposed methods were not tested for broad applications such as required for hot section components. It was the purpose of this program to evaluate proposed nonlinear methods by performing a thorough experimental and analytical study. The results illustrated that much progress was made in developing nonlinear methods.

Kim, K. S.↗