Search NASA⌕ Search

SEARCH · Search NASA

Results for “morphology changes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Supramolecular Effects of Alkyl Sulfonates in Silver Nanocrystal Synthesis

While cationic surfactants such as hexadecyltrimethylammonium bromide (CTAB) are ubiquitous in the synthesis of noble metal nanocrystals, anionic surfactants are rarely used. This work explores the addition of sodium alkyl sulfonates with chain lengths ranging from one to eight carbons to a silver nanoplatelet reaction. Short-chain sulfonates comprised of one to four carbons show little effect on the nanocrystal synthesis, but alkyl sulfonates comprised of five or more carbons at concentrations above 1 mM have a pronounced effect on the absorbance of the nanocrystals, causing a blueshift in the wavelength of maximum absorbance (λ max ) from approximately 800 to 400 nm as the sulfonate concentration is increased to 7 mM. Higher concentrations of sulfonate result in a subsequent red-shift of the peak. Investigation into the possible formation mechanisms responsible for this synthetic control revealed the absence of sulfonate micelles under the reaction conditions. Instead, we hypothesize that sulfonate bilayers are nucleated around the silver nanocrystals at concentrations below the critical micelle concentration and interact with either the citrate ligands or the silver surface to influence nanocrystal morphology, and thus absorbance. Strikingly, the addition of long-chain alkyl sulfonates to already-synthesized nanocrystals results in similar changes to the nanocrystal absorbance that occur within seconds, providing further support for the proposal that these effects are related to the surface chemistry of the nanocrystals, which appear to be highly dynamic.

alkyls↗

The utilization of ERTS-1-generated photographs in the evaluation of the Iranian playas as potential locations for economic and engineering development

The author has identified the following significant results. Hydrologic inventories, throughout the year, were made in interior basins that have not been measured previously because of their inaccessibility. Interior basins during the last ERTS-1 year (August 1972 to August 1973) had driest ground conditions in late September 1972 and had wettest ground conditions from March through May 1973, depending upon location. Bearing strengths of playa soils can be inferred from the changing hydrologic conditions through the seasons as recorded by ERTS-1, with prior ground control. Slight differences in salt-crust morphology and in moisture contest of playa soils can be greatly enhanced by rationing and stretching techniques. Differences in water area and silt content can be enhanced by using a three-stage photographic masking technique employing bands 4, 5, and 7.

Krinsley, D. B.↗

Application of modern surface analytical tools in the investigation of surface deterioration processes

Surface profilometry and scanning electron microscopy were utilized to study changes in the surface of polymers when eroded. The X-ray photoelectron spectroscopy (XPS) and depth profile analysis indicate the corrosion of metal and ceramic surfaces and reveal the diffusion of certain species into the surface to produce a change in mechanical properties. Ion implantation, nitriding and plating and their effects on the surface are characterized. Auger spectroscopy analysis identified morphological properties of coatings applied to surfaces by sputter deposition.

Buckley, D. H.↗

Spiral structure and star formation. II - Stellar lifetimes and cloud kinematics

The reliability studies using continuum gas dynamical calculations becomes questionable in connection with the apparent clumpiness of the Galaxy's interstellar medium (ISM). Roberts and Hausman (1984) have, therefore, presented a detailed model of a disk galaxy in which the ISM consists entirely of 'cloud particles', which orbit ballistically in the galaxy's gravitational field, collide inelastically with one another, and give birth to and subsequently interact with young star associations. The effects of changing the clouds's collisional mean free path have been examined, and the variations in the young star system's spiral morphology have been explored. The present investigation is concerned with a further study of this clumpy, cloudy ISM model, taking into account longer mean free path models likely to be appropriate for systems of molecular clouds. Attention is also given to the kinematics of clouds as they orbit under the influence of galactic gravity, collisions, and supernova remnants.

Hausman, M. A.↗

The Evolution of Dendrite Morphology during Isothermal Coarsening

Dendrite coarsening is a common phenomenon in casting processes. From the time dendrites are formed until the inter-dendritic liquid is completely solidified dendrites are changing shape driven by variations in interfacial curvature along the dendrite and resulting in a reduction of total interfacial area. During this process the typical length-scale of the dendrite can change by orders of magnitude and the final microstructure is in large part determined by the coarsening parameters. Dendrite coarsening is thus crucial in setting the materials parameters of ingots and of great commercial interest. This coarsening process is being studied in the Pb-Sn system with Sn-dendrites undergoing isothermal coarsening in a Pb-Sn liquid. Results are presented for samples of approximately 60% dendritic phase, which have been coarsened for different lengths of times. Presented are three-dimensional microstructures obtained by serial-sectioning and an analysis of these microstructures with regard to interface orientation and interfacial curvatures. These graphs reflect the evolution of not only the microstructure itself, but also of the underlying driving forces of the coarsening process. As a visualization of the link between the microstructure and the driving forces a three-dimensional microstructure with the interfaces colored according to the local interfacial mean curvature is shown.

Alkemper, Jens↗

Oxidation of SiC Fiber-Reinforced SiC Matrix Composites with a BN Interphase

SiC-fiber reinforced SiC matrix composites with a BN interphase were oxidized in reduced oxygen partial pressures of oxygen to simulate the environment for hypersonic vehicle leading edge applications. The constituent fibers as well as composite coupons were oxidized in oxygen partial pressures ranging from 1000 ppm O2 to 5% O2 balance argon. Exposure temperatures ranged from 816 C to 1353 C (1500 F to 2450 F). The oxidation kinetics of the coated fibers were monitored by thermogravimetric analysis (TGA). An initial rapid transient weight gain was observed followed by parabolic kinetics. Possible mechanisms for the transient oxidation are discussed. One edge of the composite coupon seal coat was ground off to simulate damage to the composite which allowed oxygen ingress to the interior of the composite. Oxidation kinetics of the coupons were characterized by scanning electron microscopy since the weight changes were minimal. It was found that sealing of the coupon edge by silica formation occurred. Differences in the amount and morphology of the sealing silica as a function of time, temperature and oxygen partial pressure are discussed. Implications for use of these materials for hypersonic vehicle leading edge materials are summarized.

Opila, Elizabeth↗

Micro-optical Distributed Sensors for Aero Propulsion Applications

The objective of this research is to develop micro-opto-mechanical system (MOMS)-based sensors for time- and space-resolved measurements of flow properties in aerodynamics applications. The measurement technique we propose uses optical resonances in dielectric micro-spheres that can be excited by radiation tunneling from optical fibers. It exploits the tunneling-induced and morphology-dependent shifts in the resonant frequencies. The shift in the resonant frequency is dependent on the size, shape, and index of refraction of the micro-sphere. A physical change in the environment surrounding a micro-bead can change one or more of these properties of the sphere thereby causing a shift in frequency of resonance. The change of the resonance frequency can be detected with high resolution by scanning a frequency-tunable laser that is coupled into the fiber and observing the transmission spectrum at the output of the fiber. It is expected that, in the future, the measurement concept will lead to a system of distributed micro-sensors providing spatial data resolved in time and space. The present project focuses on the development and demonstration of temperature sensors using the morphology-dependent optical resonances although in the latter part of the work, we will also develop a pressure sensor. During the period covered in this report, the optical and electronic equipment necessary for the experimental work was assembled and the experimental setup was designed for the single sensor temperature measurements. Software was developed for real-time tracking of the optical resonance shifts. Some preliminary experiments were also carried out to detect temperature using a single bead in a water bath.

Arnold, S.↗

High frequency QRS ECG predicts ischemic defects during myocardial perfusion imaging

Changes in high frequency QRS components of the electrocardiogram (HF QRS ECG) (150-250 Hz) are more sensitive than changes in conventional ST segments for detecting myocardial ischemia. We investigated the accuracy of 12-lead HF QRS ECG in detecting ischemia during adenosine tetrofosmin myocardial perfusion imaging (MPI). 12-lead HF QRS ECG recordings were obtained from 45 patients before and during adenosine technetium-99 tetrofosmin MPI tests. Before the adenosine infusions, recordings of HF QRS were analyzed according to a morphological score that incorporated the number, type and location of reduced amplitude zones (RAZs) present in the 12 leads. During the adenosine infusions, recordings of HF QRS were analyzed according to the maximum percentage changes (in both the positive and negative directions) that occurred in root mean square (RMS) voltage amplitudes within the 12 leads. The best set of prospective HF QRS criteria had a sensitivity of 94% and a specificity of 83% for correctly identifying the MPI result. The sensitivity of simultaneous ST segment changes (18%) was significantly lower than that of any individual HF QRS criterion (P less than 0.00l). Analysis of 12-lead HF QRS ECG is highly sensitive and specific for detecting ischemic perfusion defects during adenosine MPI stress tests and significantly more sensitive than analysis of conventional ST segments.

Source record↗

Quantifying Dissolution Dynamics in Porous Media Using a Spatial Flow Focusing Profile

Abstract The diverse range of patterns in porous media formed by dissolution processes depends on the relative magnitude of flow, transport, and chemical reactions at pore surfaces. However, distinguishing between regimes often relies solely on qualitative, visual comparisons of emergent structures. Here, we propose a quantitative measure capable of identifying different regimes using the concept of the spatial flow focusing profile, which segments the medium into cross sections along the flow direction to calculate the flow focusing index for each section. We employ this measure in numerical simulations of a dissolving porous medium using a pore network model. We obtain a morphological phase diagram of dissolution patterns, which we characterize using the flow focusing profile. In particular, we demonstrate that analyzing the temporal changes in the profile allows one to quantitatively distinguish between wormholing and channeling. The transition between them is shown to be affected by the heterogeneity of the system.

58 GEOSCIENCES↗

Crater evolutionary tracks

The technique proposed in the present paper for studying planetary surface processes is based on the measurement of crater rim height, h, depth, d, and diameter, D. The h/d and d/D ratios provide a quantitative description of crater morphology as well as a quantitative method for assessing the relative importance of competing crater modification processes (since h, d, and D change as a crater is degraded by surface processes, and h/d and d/D change with time). Different classes of processes produce distinctive evolutionary tracks on an h/d versus d/D diagram. Tracks for three general classes of crater modification (processes adding material to the crater; processes redistributing the material within the crater vicinity; and processes removing the material from the crater vicinity) are calculated, and h/d and d/D ratios for craters on the earth, moon, and Mars are compared.

Schubert, G.↗

Effect of long-term exposure to Low Earth Orbit (LEO) space environment

Data obtained from components and materials from the Solar Maximum Mission satellite are presented and compared to data for similar materials obtained from the Advanced Composite Materials Exposure to Space Experiment (ACOMEX) flown on Shuttle mission STS-41G. In addition to evaluation of surface erosion and mass loss that may be of importance to very long-term missions, comparisons of solar absorptance and thermal emittance measurements for both long and short term exposures were made. Although the ratio of absorptance over emittance can be altered by proper choice of materials to ensure a proper operating environment for the spacecraft, once the thermal design is established, it is important that the material properties not change in order to maintain the operating environment for many payload and bus items such as electronics, batteries, fuel, etc. However, data presented show significant changes after short exposure in low Earth environment. Moreover, the measured changes are shown to differ according to the manner of exposure, i.e., normal or oblique, which also affects the resultant eroded surface morphology. These results identify constraints to be considered in development of flight experiments or laboratory testing.

Zimcik, D. G.↗

Convective flow effects on protein crystal growth

The long-term stability of the interferometric setup for the monitoring of protein morphologies has been improved. Growth or dissolution of a crystal on a 100 A scale can now be clearly distinguished from dimensional changes occurring within the optical path of the interferometer. This capability of simultaneously monitoring the local interfacial displacement at several widely-spaced positions on the crystal surface with high local depth resolution, has already yielded novel results. We found with lysozyme that (1) the normal growth rate is oscillatory, and (2) the mean growth step density is greater at the periphery of a facet than in its center. The repartitioning of Na(+) and Cl(-) ions between lysozyme solutions and crystals was studied for a wide range of crystallization conditions. A nucleation-growth-repartitioning model was developed to interpret the large body of data in a unified way. The results strongly suggests that (1) the ion to lysozyme ratio in the crystal depends mostly on kinetic rather than crystallographic parameters, and (2) lysozyme crystals possess a salt-rich core with a diameter on the order of 10 microns. The computational model for diffusive-convective transport in protein crystallization (see the First Report) has been applied to a realistic growth cell geometry, taking into account the findings of the above repartitioning studies. These results show that some elements of a moving boundary problem must be incorporated into the model in order to obtain a more realistic description. Our experimental setup for light scattering investigations of aggregation and nucleation in protein solutions has been extensively tested. Scattering intensity measurements with a true Rayleigh scatterer produced systematically increased forward scattering, indicating problems with glare. These have been resolved. Preliminary measurements with supersaturated lysozyme solutions revealed that the scatterers grow with time. Work has begun on a computer program for the unified evaluation of simultaneously obtained, multi-angle static and dynamic light scattering data.

Rosenberger, Franz↗

Evaluating Surface Exposure Timescales Derived From Solar Energetic Particle Track Densities for Grains From Apollo 17 Core Sample 73002

Space weathering causes the surface soils of airless bodies like the Moon to be morphologically, microstructurally, and chemically altered due to micrometeoroid bombardment and solar wind exposure. These processes produce a multitude of microstructural and chemical changes that accumulate on individual soil grains that are continuously exposed on the surface. One characteristic is the formation of solar wind damaged rims on grains which develop from low energy solar wind particles penetrating <100 nm in depth. Also present are solar energetic particle (SEP) tracks, which are nanoscale streaks of irradiation damage in grain interiors formed by heavy, high energy ions (predominantly Fe group nuclei) originating from solar energetic particles (SEPs) that penetrate millimeters below the surface.

J. A. McFadden↗

High frequency QRS ECG predicts ischemic defects during myocardial perfusion imaging

Background: Changes in high frequency QRS components of the electrocardiogram (HF QRS ECG) (150-250 Hz) are more sensitive than changes in conventional ST segments for detecting myocardial ischemia. We investigated the accuracy of 12-lead HF QRS ECG in detecting ischemia during adenosine tetrofosmin myocardial perfusion imaging (MPI). Methods and Results: 12-lead HF QRS ECG recordings were obtained from 45 patients before and during adenosine technetium-99 tetrofosmin MPI tests. Before the adenosine infusions, recordings of HF QRS were analyzed according to a morphological score that incorporated the number, type and location of reduced amplitude zones (RAZs) present in the 12 leads. During the adenosine infusions, recordings of HF QRS were analyzed according to the maximum percentage changes (in both the positive and negative directions) that occurred in root mean square (RMS) voltage amplitudes within the 12 leads. The best set of prospective HF QRS criteria had a sensitivity of 94% and a specificity of 83% for correctly identifying the MPI result. The sensitivity of simultaneous ST segment changes (18%) was significantly lower than that of any individual HF QRS criterion (P<0.001). Conclusions: Analysis of 12-lead HF QRS ECG is highly sensitive and specific for detecting ischemic perfusion defects during adenosine MPI stress tests and significantly more sensitive than analysis of conventional ST segments.

Rahman, Atiar↗

Exceptional NH 3 Detection by Cu(cyhdc) MOF Sensor Due to H 2 O Coadsorption

Metal–organic framework (MOF)-based electrical impedance sensors are a growing class of sensors that show utility in the detection of environmentally toxic gases. Detection of trace NH 3 has been particularly difficult to design due to the low electrical response of NH 3 . However, this has been circumvented by judiciously selecting a MOF that has enhanced electrical response to NH 3 due to coadsorption with predominant atmospheric gases such as water. Herein, an MOF Cu(cyhdc) based sensor has been successfully demonstrated for the enhanced detection of environmentally toxic NH 3 gas. The sensor shows a change in impedance when it is exposed to 5 ppm of NH 3 . At 20 °C, >30% relative humidity (RH) is necessary to elicit a change, with the response increasing with RH and reaching 3170× at 92% RH, producing the largest published response to NH 3 for a MOF direct electrical sensor. In the absence of water, no change is observed toward 5 ppm of NH 3 over 20–50 °C. Here, this electrical response is largely driven by huge decreases in the imaginary component of the impedance, attributed to increased capacitance at the surface of the MOF crystallites upon NH 3 and H 2 O coadsorption. Complementary structural and microstructural characterization proves that the Cu(cyhdc) crystalline structure and morphology remain intact under trace NH 3 and/or H 2 O adsorption. Despite extremely low NH 3 , loadings seen in TGA, XPS, and FT-IR confirm NH 3 and H 2 O adsorption, and changes to the metal-carboxylate IR peak positions are observed upon NH 3 adsorption. Concentrated primarily at the outer surfaces of the MOF crystallites, this NH 3 and H 2 O coadsorption effectively increases the surface capacitance across the Cu(cyhdc) powder and enables direct electrical detection of trace NH 3 . Together, these results demonstrate how coadsorption of specific molecules (H 2 O) can be used to enable the electrical detection of trace toxic gases that would otherwise not have produced a MOF sensor response.

ammonia↗

Effect of surface texture by ion beam sputtering on implant biocompatibility and soft tissue attachment

The objectives in this report were to use the ion beam sputtering technique to produce surface textures on polymers, metals, and ceramics. The morphology of the texture was altered by varying both the width and depth of the square pits which were formed by ion beam erosion. The width of the ribs separating the pits were defined by the mask used to produce the texture. The area of the surface containing pits varies as the width was changed. The biological parameters used to evaluate the biological response to the texture were: (1) fibrous capsule and inflammatory response in subcutaneous soft tissue; (2) strength of the mechanical attachment of the textured surface by the soft tissue; and (3) morphology of the epidermal layer interfacing the textured surface of percutaneous connectors. Because the sputter yield on teflon ribs was approximately an order of magnitude larger than any other material the majority of the measurements presented in the report were obtained with teflon.

Gibbons, D. F.↗

Formate-Induced Dissolution and Reprecipitation of a Copper Electrocatalyst during Electrochemical CO 2 Reduction Reaction

Catalyst size, morphology, and crystal structure play crucial roles in determining the activity and selectivity of electrochemical CO 2 reduction reactions, which are known to change during the reaction process. A comprehensive understanding of how, when, and why these parameters evolve under operational conditions is essential for developing stable, efficient, and selective catalysts. In this study, we reveal that formate, one of the reaction products, contributes to the degradation of copper catalysts through a ligand-assisted dissolution mechanism. Utilizing in situ electrochemical atomic force microscopy and ex-situ scanning and transmission electron microscopies, we observed a significant reduction in the size of copper nanoparticles, which decreased from over 30 nm to less than 10 nm in diameter within 60 min of CO 2 RR. The temporal production of formate correlated with the particle size changes. Furthermore, analysis of the electrolyte using inductively coupled plasma optical emission spectroscopy confirmed the dissolution of copper nanoparticles. Control experiments involving various reaction products (H 2 , CO, and HCOO – ) demonstrated that formate significantly promotes copper dissolution, thereby highlighting its role in the ligand-assisted dissolution mechanism of copper electrocatalysts. In conclusion, our findings provide critical insights into copper catalyst behavior during electrochemical CO 2 reduction, facilitating the design of more resilient and effective electrocatalysts.

Catalysts↗

X-Ray Variability in M87

We present the evidence for X-ray variability from the core and from knot A in the M87 jet based on data from two observations with the Einstein Observatory High Resolution Imager (HRI) and three observations with the ROSAT HRI. The core intensity showed a 16% increase in 17 months ('79-'80); a 12% increase in the 3 years '92 to '95; and a 17% drop in the last half of 1995. The intensity of knot A appears to have decreased by 16% between 92Jun and 95Dec. Although the core variability is consistent with general expectations for AGB nuclei, the changes in knot A provide constraints on the x-ray emission process and geometry. Thus we predict that the x-ray morphology of knot A will differ significantly from the radio and optical structure.

Harris, Daniel E.↗