Search NASA⌕ Search

SEARCH · Search NASA

Results for “phase analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Behavior of Ga, In, Sn, and Te in Copper Matte Smelting

The distributions of Ga, In, Sn, and Te between copper-iron mattes and silica-saturated iron silicate slags over a wide range of matte grades 55 to 75 pct Cu were determined at 1300 °C using a gas-phase equilibration-quenching technique and direct phase composition analysis by Electron Probe X-ray Microanalysis and Laser Ablation-Inductively Coupled Plasma-Mass Spectrometry. Alumina from aluminum, a typical minor element of electric and electronic copper scrap, and lime were adopted as slag modifiers for increasing the trace element recoveries. Gallium and tin were distributed predominantly in the slag, indium preferred sulfide matte at low matte grades and slag at high, whereas tellurium strongly favored the sulfide matte in particular in high matte grades. The slag modifiers alumina and lime had a minor impact on the distribution coefficients of gallium and tin, but for indium and tellurium the distribution coefficients were more strongly affected by the basic oxides. The strong tendencies of tin and tellurium to vaporize at the experimental temperature were confirmed.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Effect of thermal treatments on electrochemical behavior of binder jetted 17-4 PH stainless steel

Binder jetted 17–4 PH stainless steel was post-processed to relate heat treatment, microstructure, and corrosion in 3.5 wt% NaCl. Specimens were sintered at 1380 or 1400 °C, solution-annealed at 1055 °C for 1 h, and aged at 482 °C for 1 h. Here, as-sintered parts showed α′-martensitic matrix with a δ-ferrite network and Cu-rich precipitates in ferrite; inclusions (MnS, NbC) promoted localized attack. solutionizing redistributed elements and reduced ferrite, while aging generated coherent Cu nano-precipitates. Corrosion resistance was highly sensitive to post-processing in which aged specimens exhibited the lowest corrosion current density and formed a thicker, stable Cr 2 O 3 -rich passive film, whereas sintered specimens degraded most. Pitting potential depended on sintering temperature and microstructure, with 1400 °C sintering yielding more positive pitting potentials and the best overall performance after aging. Although the 1400-solutionized condition showed a relatively noble pitting response versus 1380-solutionized, it displayed unstable corrosion kinetics attributed to an imperfect passive film linked to higher NbC density. XPS depth profiles corroborated these trends, showing thicker, more continuous Cr 2 O 3 in aged states and discontinuous/thinning oxides in less resistant conditions. Practically, high-temperature sintering (∼1400 °C) followed by solutionizing and aging is recommended, with further gains expected from reducing NbC/MnS populations and porosity via powder and process control.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Multimodal Bayesian registration of noisy functions using Hamiltonian Monte Carlo

Functional data registration is a necessary processing step for many applications. The observed data can be inherently noisy, often due to measurement error or natural process uncertainty; which most functional alignment methods cannot handle. A pair of functions can also have multiple optimal alignment solutions, which is not addressed in current literature. In this paper, a flexible Bayesian approach to functional alignment is presented, which appropriately accounts for noise in the data without any pre-smoothing required. Additionally, by running parallel MCMC chains, the method can account for multiple optimal alignments via the multi-modal posterior distribution of the warping functions. To most efficiently sample the warping functions, the approach relies on a modification of the standard Hamiltonian Monte Carlo to be well-defined on the infinite-dimensional Hilbert space. In this work, this flexible Bayesian alignment method is applied to both simulated data and real data sets to show its efficiency in handling noisy functions and successfully accounting for multiple optimal alignments in the posterior; characterizing the uncertainty surrounding the warping functions.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Specifying angular reference for robust three-phase state estimation

While the phase angle of any of the bus voltages can be chosen as the angular reference in the state estimation formulation of positive sequence networks, the same approach does not readily extend to three-phase network state estimation problem. It is commonly assumed that there is at least one bus where the bus voltages are perfectly balanced with phase angles displaced ±120° and these balanced three phase voltages are used as the three-phase reference in solving the three-phase state estimation problem. This assumption may be quite realistic in transmission networks, and for distribution networks with a strong transmission system connection. However, it might not be realistic to assume existence of a perfectly balanced reference bus in today’s distribution systems with ever increasing penetration of renewable sources or for isolated operation of microgrids. In this paper, a novel state estimation formulation will be presented which facilitates correct solution irrespective of the existence of buses with perfectly balanced voltages. The new formulation is general, and lends itself to bad data processing. It yields accurate results in any three-phase power system irrespective of its operating conditions (balanced or highly unbalanced), configuration (isolated microgrid, connected to transmission system, etc.) and whether or not it contains any synchronous generators. The performance of the method is validated using the IEEE 123 bus three-phase system.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2019

Microstructure and fission products in the UCO kernel of an AGR-1 TRISO fuel particle after post irradiation safety testing

Tristructural isotropic (TRISO) coated particle fuel as a key fuel concept for the High Temperature Gas-cooled Reactors (HTGRs) and a candidate accident tolerant fuel (ATF) has been currently investigated under the US-DOE Advanced Gas Reactor (AGR) fuel development and qualification program. Over the past decades, extensive studies have been conducted to evaluate the fission product release, diffusion on Ag, Pd and Cd in the SiC layer and the TRISO coating system, and post-safety-test performance. However, to date, there are limited reported results on the fuel kernels’ response to irradiation with or without post irradiation high temperature annealing. To incrementally fulfill this knowledge gap extensive studies using transmission electron microscopes (TEM) and atom probe tomography (APT) were conducted on a TRISO fuel particle kernel with a 19.74% 235U enrichment, irradiated to 18.63% FIMA and subsequently subjected to post-safety testing at 1600ºC for 300 hours.. Microstructure characterizations, elemental analysis, and phase identification were conducted using conventional TEM and scanning TEM (STEM) imaging, energy-dispersive X-ray spectroscopy (EDS), selected-area electron diffraction (SAED) and atom probe tomography (APT). The following findings were made: (1) significant reconstructions and phase evolutions occurred in the irradiated and post-safety annealed fuel kernel, and its microstructure consists of two primary phases, namely a “high-Z (atomic mass)” UC phase and a “low-Z” UO phase, (2) no fission gas bubbles are identified within the fuel kernel, that can be attributed to the high temperature post safety annealing, (3) fission products Zr, Nb, Mo, Ru, Tc and Rh were found to preferentially segregate into UC phase or to form metallic precipitates, while the lanthanide fission products tend to stay in the solution of UO phase, (4) Pd was detected in the rod-shaped precipitates, (5) APT data reveals segregation of Te, Pd, and Ag at the UO and UC phase boundary, and (6) Pd is detected in both the UO and UC phases but with an enrichment in the former one.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Effect of Re and Al additions on the microstructure and mechanical properties of Nb-18Ti-12W alloy

Microstructure and mechanical properties at 25–1200 °C of new refractory alloys, Nb-18Ti-12W (NTW), Nb-18Ti-12W-5Re (NTW-R) and Nb-18Ti-12W-5Re-1Al (NTW-RA), all compositions are in atomic percent, are reported. The alloys are developed as an alternative to a denser, more expensive and difficult-to-process refractory alloy WC-3009. After production by arc melting and hot isostatic pressing at 1400 °C, 207 MPa for 3 h, the alloys have a BCC crystal structure with the average grain size of ~150–200 μm and contain low volume fraction of (Ti,N)-rich precipitates near grain boundaries. NTW shows excellent malleability at all studied temperatures. Its yield stress at 25 °C, 1000 °C and 1200 °C is 874 MPa, 353 MPa and 202 MPa, respectively. The NTW-R and NTW-RA alloys are stronger at all the studied temperatures; however, they lack in compression ductility at 25 °C. As a result, extensive deformation twinning and formation of intergranular voids precede the fracture of these two alloys at 25 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Exploring the potential of using L-Band InSAR for the mapping of flooded vegetation in tropical wetlands

Wetlands play a critical role in global water and carbon cycles, yet monitoring their water extent remains difficult, particularly beneath dense vegetation. SAR-based techniques such as backscatter thresholding are limited by complex scattering mechanisms, while fully polarimetric SAR (PolSAR) data capable of detecting doublebounce scattering remain scarce. To address these challenges, this study evaluates the potential of Interferometric SAR (InSAR) for mapping water surfaces beneath vegetation, termed flooded vegetation, using the Atrato floodplain in Colombia as a case study. We develop an automated workflow combining InSAR fringe detection with local phase homogeneity analysis and random sampling of processing parameters to generate probabilistic flooded vegetation maps. Applied to ALOS PALSAR-1 L-band image pairs from 2007–2011, the workflow captures seasonal fluctuations in flooded extent ranging from 500 to 1,500 km2. Compared to other L-band SAR inundation products, the InSAR-based maps identify broader flooded areas, with ~70% agreement in pairwise comparisons. Around 84% of detections align with existing wetland inventories and seasonal changes correspond with regional hydrological indicators, including terrestrial water storage anomalies and water gauge measurements. PolSAR analysis shows that InSAR complements backscatter-based methods by detecting inundation in areas with weak double-bounce signals. These findings suggest that combining InSAR with backscatter-based methods can improve detection of flooded vegetation, which is especially relevant for the upcoming NISAR mission that will offer frequent global L-band observations.

Coastal inundation↗
DOE OSTI2020

Experimental evaluation of direct current magnetron sputtered and high-power impulse magnetron sputtered Cr coatings on SiC for light water reactor applications

Two types of physical vapor deposition Cr coatings were deposited on chemical vapor deposited SiC coupons using conventional direct current magnetron sputtering (DCMS) and high-power impulse magnetron sputtering (HiPIMS) to mitigate the corrosion of SiC, an advanced fuel and structural material in light water nuclear reactor cores. Coating microstructure was characterized using scanning electron microscopy and scanning transmission election microscopy. X-ray diffraction analysis was conducted for phase identification and qualitative analysis of residual stresses. The mechanical integrity of the coatings was evaluated using scratch testing, micro-indentation, and nano-indentation tests. Additionally, the microstructure of the DCMS coating consisted of fine columnar grains with nanoscale intercolumnar channels, while the HiPIMS microstructure was denser and free of any columnar defects. The DCMS coating showed a small tensile residual stress, while the HiPIMS coating was under compressive stress. Both types of coatings showed good mechanical integrity in terms of ductility and adhesion to the substrate. Corrosion performance of the coatings was assessed with a 30-day high temperature water autoclave test. Both types of coatings formed a protective Cr 2 O 3 surface layer 20-30 nm thick during the autoclave test. In the DCMS coating, the columnar defects provided permeation pathways for water penetration resulting in oxide formation in the intercolumnar regions in the interior of the coating. Overall, both types of Cr coatings offer promise for the mitigation of hydrothermal corrosion of SiC in light water reactor operating environments.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Symmetry in Seeded Metal Nanocrystal Growth

Symmetry underpins the structure and function of the world around us and is also captured in modern nanomaterials, where changing the symmetry of a nanocrystal or the interparticle spacing and orientation of nanocrystal building blocks in a superlattice can give new function. However, the synthesis and assembly of nanocrystals have been limited largely to simple compositions and structures. It remains a grand challenge to achieve nanocrystals with compositional and structural complexity while maintaining the monodispersity required for their use. This Account will illustrate through recent examples that seeded methods enable the synthesis of compositionally and structurally complex multimetallic crystals with defined and predictable symmetries for applications in plasmonics and catalysis. This outcome arises because the barrier for heterogeneous nucleation (i.e., seeded) is lower than that of homogeneous nucleation, where seeds can serve as preferential sites for the growth of complex structures and crystal phases. Our analysis begins by considering metal overgrowth from single-crystalline seeds of different shapes and symmetries, where the kinetics of adatom addition to seeds relative to their diffusion across seeds accounts for the expressed nanocrystal shapes. These results are then compared to overgrowth from seeds with different internal structures (i.e., planar defects), where the relationships between nanocrystal size and volumetric strain energy and surface energy are discussed. A major finding from this analysis is that often the underlying symmetry of seeds can be predictably transferred to the final crystals during overgrowth processes. Consequences of this finding are the predictable syntheses of crystals with different hierarchies akin to snowcrystals as well as nanocrystals with complex compositions (e.g., quaternary nanoparticles). Yet, there are subtle aspects to seeded growth that pave a path toward examples where nanocrystal symmetry has been reduced compared to the original seeds in a controlled manner. As we found, both the concentrations of metal precursors and capping agents can impact whether symmetry is transferred or reduced during overgrowth. Examples from our laboratory will be placed in context to other reported strategies for symmetry breaking. As will be argued, understanding what conditions favor symmetry preservation versus symmetry reduction during seeded crystal growth is central to accessing next-generation crystal forms. The Account concludes by outlining synthetic challenges associated with forming nanoscale heterostructures with precise 3-D placement of different materials within a given nanocrystal as well as facet control within different material domain and interface engineering. Furthermore, we envision meeting these challenges through regioselective and chemoselective seeded syntheses for which a foundation is outlined herein.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Is the Local Ion Density Sufficient to Drive NaCl Nucleation from the Melt and Aqueous Solution?

Even though nucleation is ubiquitous in different science and engineering problems, investigating nucleation is extremely difficult due to the complicated ranges of time and length scales involved. In this work, we simulate NaCl nucleation in both molten and aqueous environments using enhanced sampling of all-atom molecular dynamics with deep-learning-based estimation of reaction coordinates. By incorporating various structural order parameters and learning the reaction coordinate as a function thereof, we achieve significantly improved sampling relative to traditional ad hoc descriptions of what drives nucleation, particularly in an aqueous medium. Our results reveal a one-step nucleation mechanism in both environments, with reaction coordinate analysis highlighting the importance of local ion density in distinguishing solid and liquid states. However, although fluctuations in the local ion density are necessary to drive nucleation, they are not sufficient. Our analysis shows that near the transition states, descriptors such as enthalpy and local structure become crucial. Furthermore, our protocol proposed here enables robust nucleation analysis and phase sampling and could offer insights into nucleation mechanisms for generic small molecules in different environments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Disentangling the Effects of Temperature, Moisture, and Substrate Availability on Soil CO 2 Efflux

Soil respiration ($R_s$), the largest carbon emission flux in ecosystems, is usually modeled as an empirically parameterized function of temperature, and sometimes water availability. The likely contribution by other factors, such as carbohydrate substrate supply from photosynthesis, has been recognized, but modeling capacity to use this information is limited. Wavelet transformations of the residuals of a seasonal Q 10 temperature response model indicated structure at different temporal scales. In this work, we hypothesize that this indicates the lack of explicit representation of relevant processes in the models. Using cross-spectral analysis, we found that time series of photosynthetically active radiation explained most of the diurnal variation, temperature, explained variability at multiple time scales (diurnal-synoptic), whereas volumetric soil water content correlated with variability in Rs at scales 15-30 days. The results suggest that the time domains of influence for different driving variables of $R_s$ are discrete, and largely nonoverlapping, and represent functional relationships between soil biological activity and its constraints. Analysis of phase angles showed that $R_s$ lagged photosynthetically active radiation by 1.5-3.0 hr. As this time lag was the same in both young and mature trees, with more than fivefold difference in transport distances, we hypothesize that this finding adds to the body of literature that support the pressure-concentration-wave model of carbohydrate availability in plants.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Identification of high-dielectric constant compounds from statistical design

Abstract The discovery of high-dielectric materials is crucial to increasing the efficiency of electronic devices and batteries. Here, we report three previously unexplored materials with very high dielectric constants (69 < ϵ < 101) and large band gaps (2.9 < E g (eV) < 5.5) obtained by screening materials databases using statistical optimization algorithms aided by artificial neural networks (ANN). Two of these new dielectrics are mixed-anion compounds (Eu 5 SiCl 6 O 4 and HoClO) and are shown to be thermodynamically stable against common semiconductors via phase diagram analysis. We also uncovered four other materials with relatively large dielectric constants (20 < ϵ < 40) and band gaps (2.3 < E g (eV) < 2.7). While the ANN training-data are obtained from the Materials Project, the search-space consists of materials from the Open Quantum Materials Database (OQMD)—demonstrating a successful implementation of cross-database materials design. Overall, we report the dielectric properties of 17 materials calculated using ab initio calculations, that were selected in our design workflow. The dielectric materials with high-dielectric properties predicted in this work open up further experimental research opportunities.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mechanistic studies of NH 3 -assisted reduction of mononuclear Cu(ii) cation sites in Cu-CHA zeolites

Cu-Exchanged zeolites catalyze various redox reactions including the selective catalytic reduction (SCR) of NO x with NH 3 and the partial oxidation of hydrocarbons. The reduction of Cu(II) cations to Cu(I) by NH 3 alone has been observed experimentally, yet fundamental details regarding the Cu active site requirements, reaction stoichiometry, and reaction mechanism remain incompletely understood. Here, we synthesized model Cu-exchanged chabazite (Cu-CHA) zeolites with varying Cu ion densities and distributions of mononuclear Cu(II) ion site types (Cu 2+ , (CuOH) + ) and studied NH 3 -assisted Cu(II) reduction reactions using a combination of spectroscopic, titrimetric, and gas-phase product analysis methods. In situ UV-visible and X-ray absorption spectroscopies were used to monitor and quantify the transient reduction of Cu(II) to Cu(I) during exposure to NH 3 (473 K), in concert with titration methods that use NO and NH 3 co-reductants to fully reduce to the Cu(I) state any residual Cu(II) ions that remained after treatments in NH 3 alone for a given time period. The techniques provide quantitative evidence that both mononuclear Cu(II) site types are able to reduce in NH 3 alone, and do so to similar extents as a function of time. NH 3 temperature programmed reduction (TPR) revealed that the reaction stoichiometry of NH 3 -assisted reduction forms approximately one equivalent of N 2 per 6 Cu sites, regardless of Cu speciation or density, consistent with a six-electron reduction process whereby two NH 3 molecules react with six Cu(II) species to produce one N 2 molecule and six Cu(I) species. Furthermore, these findings provide new insights into the reaction pathways and mechanisms by which NH 3 alone reduces mononuclear Cu(II) sites in zeolites, which are undesired side-reactions that occur during steady-state NO x SCR and can unintentionally influence SCR-relevant spectroscopic or titrimetric characterization experiments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Interplay between fluctuation driven toroidal axisymmetric flows and resistive ballooning mode turbulence

An interplay between fluctuation driven toroidal axisymmetric flows (convective cell modes) and resistive ballooning mode turbulence after the pedestal collapse is numerically studied by a four-field reduced MHD model in the BOUT++ framework. The strong flow shear suppresses the radial transport of pressure filaments, and the pressure profile in the pedestal region is partially recovered. As a result, a secondary instability is quasilinearly excited, which yields a secondary collapse. Here, the subsequent damped oscillation is also analyzed by phase diagram analysis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗