Search NASA⌕ Search

SEARCH · Search NASA

Results for “snapping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Nano-ALSEP: Use of Nano-Sat Technology to Advance Lunar Exploration Science/Engineering

During the Apollo program, unique ALSEP (Apollo Lunar Surface Experiments Package) stations were deployed and left on the surface for long term data collection. Powered by a SNAP-27 electrical power source, the packages continued to transmit useful data until September 30, 1977 (the end of the Fiscal year and termination of the budget). The instruments were varied but included an active seismic experiment (ASE), charged particle experiments, magnetometer experiment, micro-meteoroide/bolide detection experiments. Only only one, the Laser Ranging Retro-Reflector (LRRR) was continued to be used to the present day due to the passive nature of the device. After a dearth of data during an absence of 50 years, is it possible to restart similar packages using the advances in nano-sat technologies? An innovation effort is proposed that would first look at a 2U nano-sat package evolving to an eventual radio-isotope powered system that could be either part of a lunar lander or as an independent package. In the first phase, the packages would only survive during the Lunar day. In a second phase, the later radio-isotope options would place the surface packages in a semi-dormant mode during the Lunar night cycle. Communication capability developed in the TechEdSat-n flight series (UHF, S, X and optical bands) would help to independently close the link and potentially explore IoT devices that were powered only in the sunlight. In addition, limited mobility in the form factor of a nano-rover might also greatly extend the utility of such packages while adding evolutionary capability - and finally continue where the Apollo program was forced to leave off.

M Murbach↗

Tracking the Rates and Mechanisms of Canopy Damage and Recovery Following Hurricane Maria Using Multitemporal Lidar Data

Hurricane Maria, a Category 4 storm, snapped and uprooted canopy trees, removed large branches, and defoliated vegetation across Puerto Rico. The magnitude of forest damages and the rates and mechanisms of forest recovery following Maria provide important benchmarks for understanding the ecology of extreme events. We used airborne Lidar data acquired before (2017) and after Maria (2018, 2020) to quantify landscape-scale changes in forest structure along a 439-ha elevational gradient (100–800 m) in the Luquillo Experimental Forest. Damages from Maria were widespread, with 73% of the study area losing ≥ 1 m in canopy height (mean = −7.1 m). Taller forests at lower elevations suffered more damage than shorter forests above 600 m. Yet only 13.5% of the study area had canopy heights ≤ 2 m in 2018, a typical threshold for forest gaps, highlighting the importance of damaged trees and advanced regeneration on post-storm forest structure. Heterogeneous patterns of regrowth and recruitment yielded shorter and more open forests by 2020. Nearly 45% of forests experienced initial height loss > 1 m (2017–2018) followed by rapid height gain > 1 m (2018–2020), whereas 21.6% of forests with initial height losses showed little or no height gain, and 17.8% of forests exhibited no height changes larger than ± 1 m in either period. Canopy layers < 10 m tall accounted for most increases in canopy height and fractional cover between 2018 and 2020, with gains split evenly between height growth and lateral crown expansion by surviving individuals. These findings benchmark rates of gap formation, crown expansion, and canopy closure following hurricane damage and highlight the diversity of ecosystem impacts from heterogeneous spatial patterns and vertical stratification of forest regrowth following a major disturbance event.

forest structure↗

Adjusting a Full Body Model to Mitigate Inverse Kinematics Artifacts in Opensim

BACKGROUND: In support of Vibration Isolation and Stabilization (VIS) system development for Human Health Countermeasures (HHC) exercise systems in space, such as the European Enhanced Exploration Exercise Device (E4D) [1], dynamic quantities required to model the response of a proposed VIS while considering the effect of VIS motion on the forces between the human and VIS platform were obtained using motion capture data [2]. On occasion, large-amplitude oscillatory spikes were found in the subject’s linear and angular momentum derivatives, affecting analyses that depend on forces and moments derived from motion capture. The purpose of this investigation was to identify causes of these artifacts and techniques for their resolution. METHODS AND RESULTS: To obtain the required human dynamic quantities to drive the VIS simulation, motion capture data was collected containing recorded trajectories of passive retroreflective markers on body landmarks of an exercising subject. Since the full body Rajagopal model [3] was originally used to enhance gait analysis, upper body joints did not require large Ranges of Motion (ROM). We thus modified the Rajagopal model [4, 5] to allow it to be used for upper body intensive exercises like those common to the E4D. OpenSim Inverse Kinematics (IK) [6] was performed using these scaled subject models to generate the joint angles throughout the exercise while minimizing marker error. At times, the arms were observed to ‘snap’ from one configuration to another, causing spike artifacts. Following IK, a custom OpenSim plugin [7] was used to determine the required dynamic quantities including the rates of change of the linear and angular momenta of the human. Since motion capture is recorded at a larger time step than required by the VIS simulation, the human center of mass location was fit with splines and a second derivative taken to obtain the momentum derivative, allowing the VIS simulation to maintain conservation of momentum when appropriate. In a few cases during this stage, artifacts much larger than the expected noise of the second derivatives were introduced. Investigation of cases containing artifacts revealed several modifications that could be made to the OpenSim model to improve IK results. Since OpenSim models use Euler angles and rotation sequences, ‘gimbal lock’ would be encountered in the arms when raised 90 degrees to the side (e.g., T-pose, some hang clean exercise, etc.). This was resolved by reorienting the horizontal axes at the shoulder joint by 45 degrees, placing ‘gimbal lock’ outside common arm ROM, with the arm ROMs adjusted following this change. Elbow and wrist ROMs could also be adjusted to allow realistic motion while at the same time limiting the likelihood of unrealistic orientations. On occasion, the arms flipped backwards when raised above the head. This was prevented by using medial elbow markers in scaling and IK. When medial markers were not available, the acromial joint location in the unscaled model was shifted before model scaling to better align the arm with available markers. Lastly, artifacts which became apparent after taking the second derivatives of spline-fit data were found to occur in cases when the pelvis rotation limit prevented the full range of motion of an exercise. These issues were resolved by unclamping the pelvis rotation limit. Through this investigation, an understanding of conditions leading to IK artifacts was acquired allowing the automation of artifact detection. These artifact detection and mitigation techniques can be applied toward modeling of upper body motions in aerospace and other fields for improved IK results.

C A Bell↗

Tracking the Rates and Mechanisms of Canopy Damage and Recovery Following Hurricane Maria Using Multitemporal Lidar Data

Hurricane Maria, a Category 4 storm, snapped and uprooted canopy trees, removed large branches, and defoliated vegetation across Puerto Rico. The magnitude of forest damages and the rates and mechanisms of forest recovery following Maria provide important benchmarks for understanding the ecology of extreme events. We used airborne Lidar data acquired before (2017) and after Maria (2018, 2020) to quantify landscape-scale changes in forest structure along a 439-ha elevational gradient (100–800 m) in the Luquillo Experimental Forest. Damages from Maria were widespread, with 73% of the study area losing ≥ 1 m in canopy height (mean = −7.1 m). Taller forests at lower elevations suffered more damage than shorter forests above 600 m. Yet only 13.5% of the study area had canopy heights ≤ 2 m in 2018, a typical threshold for forest gaps, highlighting the importance of damaged trees and advanced regeneration on post-storm forest structure. Heterogeneous patterns of regrowth and recruitment yielded shorter and more open forests by 2020. Nearly 45% of forests experienced initial height loss > 1 m (2017–2018) followed by rapid height gain > 1 m (2018–2020), whereas 21.6% of forests with initial height losses showed little or no height gain, and 17.8% of forests exhibited no height changes larger than ± 1 m in either period. Canopy layers < 10 m tall accounted for most increases in canopy height and fractional cover between 2018 and 2020, with gains split evenly between height growth and lateral crown expansion by surviving individuals. These findings benchmark rates of gap formation, crown expansion, and canopy closure following hurricane damage and highlight the diversity of ecosystem impacts from heterogeneous spatial patterns and vertical stratification of forest regrowth following a major disturbance event.

forest structure↗

Transient Optimization of a Gas Turbine Engine

Gas turbine engines are the primary power plants for modern commercial aircraft. Transients prompted by significant changes in thrust or power demand are common and unavoidable. Extreme transient scenarios such as those associated with a go-around during a landing attempt are possible and must be accounted for in the design of the engine and its controller. Engine transients tend to cause a reduction in compressor operability margin, which must be addressed by the engine control system and accounted for in the engine design to prevent events such as compressor stall/surge and combustor blow out. Transient operability concerns typically lead to compromises in the engine design that sacrifice efficiency and/or limit responsiveness. Transient operability is typically managed by logic that limits the fuel flow command. If this logic is not optimized, then the potential for valuable performance could be lost. This study presents a strategy for optimizing the transient limit logic and proposes a strategy for updating the control logic over the lifespan of the engine. The results demonstrate significant improvements in transient operability. For example, of the results at sea level static conditions demonstrated a 31% reduction in the usage of the high pressure compressor operability stack during a snap acceleration transient. Furthermore, a reinforcement learning algorithm is demonstrated to modify the transient logic as the engine degrades to minimize response time while respecting a prescribed compressor operability margin limit. A simple demonstration of the reinforcement learning algorithm resulted in a thrust response time reduction of ~11.8%.

transient↗

Transient Optimization of a Gas Turbine Engine

Gas turbine engines are the primary power plants for modern commercial aircraft. Transients prompted by significant changes in thrust or power demand are common and unavoidable. Extreme transient scenarios such as those associated with a go-around during a landing attempt are possible and must be accounted for in the design of the engine and its controller. Engine transients tend to cause a reduction in compressor operability margin, which must be addressed by the engine control system and accounted for in the engine design to prevent events such as compressor stall/surge and combustor blow out. Transient operability concerns typically lead to compromises in the engine design that sacrifice efficiency and/or limit responsiveness. Transient operability is typically managed by logic that limits the fuel flow command. If this logic is not optimized, then the potential for valuable performance could be lost. This study presents a strategy for optimizing the transient limit logic and proposes a strategy for updating the control logic over the lifespan of the engine. The results demonstrate significant improvements in transient operability. For example, of the results at sea level static conditions demonstrated a 31% reduction in the usage of the high pressure compressor operability stack during a snap acceleration transient. Furthermore, a reinforcement learning algorithm is demonstrated to modify the transient logic as the engine degrades to minimize response time while respecting a prescribed compressor operability margin limit. A simple demonstration of the reinforcement learning algorithm resulted in a thrust response time reduction of ~11.8%.

transient↗

Evaluating SAR Radiometric Terrain Correction Solutions: Optimal products for applied users

Operational applications of Synthetic Aperture Radar (SAR) are under development around the world, driven by the regularly-acquired, free-and-open source C-band SAR observations provided by ESA’s Sentinel-1 sensor constellation since 2014. Groups like SERVIR, a joint NASA and USAID initiative, are at the forefront of remote sensing applications for societal benefit. A takeaway from SERVIR’s experience is the need for appropriately geocoded and fully calibrated SAR data that is ready to use for a range of ecosystems-related applications. Radiometric Terrain Corrected (RTC) data are key entry-level products for multiple applications that range from ecosystems to hazards. This work fills a gap in current research by evaluating several RTCs produced by open-source software solutions (SNAP-7 and ISCE-2), the gold standard commercial software (GAMMA), a Google Earth Engine (GEE) based workflow, and the uncorrected GRD products currently available in GEE. RTCs were analyzed for geolocation quality, absolute radiometric calibration, and fidelity of the radiometric terrain flattening over ten sites representing varied terrains. In addition, a time series analysis was conducted over two locations. Overall, no significant differences for radiometric calibration were found across RTC products. However, all RTCs performed better than uncorrected GRD products. The main differences between products were found in geolocation quality. These results not only demonstrate the need for the uptake and distribution of RTC products for ecosystems applications, but demonstrate the ability to do so with open source methods, adding value to developing affordable operational applications.

Helen Blue Parache↗

Transient Optimization of a Gas Turbine Engine

Gas turbine engines are the primary power plants for modern commercial aircraft. Transients prompted by significant changes in thrust or power demand are common and unavoidable. Extreme transient scenarios such as those associated with a go-around during a landing attempt are possible and must be accounted for in the design of the engine and its controller. Engine transients tend to cause a reduction in compressor operability margin, which must be addressed by the engine control system and accounted for in the engine design to prevent events such as compressor stall/surge and combustor blow out. Transient operability concerns typically lead to compromises in the engine design that sacrifice efficiency and/or limit responsiveness. Transient operability is typically managed by logic that limits the fuel flow command. If this logic is not optimized, then the potential for valuable performance could be lost. This study presents a strategy for optimizing the transient limit logic and proposes a strategy for updating the control logic over the lifespan of the engine. The results demonstrate significant improvements in transient operability. For example, of the results at sea level static conditions demonstrated a 31% reduction in the usage of the high pressure compressor operability stack during a snap acceleration transient. Furthermore, a reinforcement learning algorithm is demonstrated to modify the transient logic as the engine degrades to minimize response time while respecting a prescribed compressor operability margin limit. A simple demonstration of the reinforcement learning algorithm resulted in a thrust response time reduction of ~11.8%.

transient↗

Quantifying Mangrove Canopy Regrowth and Recovery After Hurricane Irma With Large-Scale Repeat Airborne Lidar in the Florida Everglades

Hurricane Irma caused significant damages to mangrove forested wetlands in south Florida, including defoliation, tree snapping, and uprooting. Previous studies have used optical satellite imagery to estimate large-scale forest disturbance and resilience patterns. However, satellite images alone cannot provide measurements of vertical mangrove structure. In this study, we used dense point cloud data collected by NASA Goddard’s LiDAR, Hyperspectral, and Thermal (G-LiHT) airborne imager before (March 2017) and after (December 2017 and March 2020) Hurricane Irma to quantify the recovery, or lack thereof, of the three-dimensional (3D) mangrove forest structure. Recent resilience and vulnerability models developed from Landsat time series following the storm were used to group the lidar data into distinct disturbance-recovery classes. We then analyzed lidar-based forest canopy within each of the recovery classes to test a suite of forest structural characteristics. Our results indicate that 77.0 % of the survey area experienced canopy height loss three months after Hurricane Irma, whereby the majority of canopy height loss occurred in areas with the tallest mangrove forests (i.e., 15–25 m tall). Our analysis shows that the mangrove canopy height in South Florida increased by an average 0.26 m from December 2017 to March 2020, with most of the forest (84.7 % of the survey area) experiencing canopy height regrowth. However, only 38.1 % of the survey area has recovered to pre-storm canopy height. The distribution of canopy height was significantly altered by Hurricane Irma in the low and intermediate resilience classes, but were not significantly different 2.5 years later. Indeed, in areas of low resilience, little to no vertical change has occurred suggesting the absence of canopy regrowth and natural regeneration. Conversely, mangroves in high resilience class, which are dominated by shorter canopies (<5 m), were not heavily damaged by the storm and have maintained the same structural attributes as those before Hurricane Irma. Our findings highlight that hurricane disturbances significantly alter mangrove forest canopy structure, but recovery of vertical structure varies by resilience classes, species composition, and canopy height.

Lidar↗

Optimization Considerations for Annular Linear Electromagnetic Pumps for Space Nuclear Power and Propulsion

The Need for High Performance Liquid Metal Pumps Testing Power and Efficiency Considerations Liquid metal cooled reactors is one option for space nuclear power for settlements and electric propulsion vehicles (Snap 10 A, SP100, Soviet Topaz reactors) • High heat capacity • High boiling point (NaK~1200K) • Simplified heat transfer loop • Good neutronics Liquid metal EM pumps are desired over conventional pumps owing to lack of seals, bearings elimination of cavitation issues, lower mass and eliminates mechanical impeller • Conduction pumps (typically DC-high current, low voltage; ~5% efficiency) • Induction pumps (typically AC, high efficiency ~40%) Annular linear induction pump is an EM pump with no moving parts and of cylindrical/tubular geometry which makes it straightforward to integrate in conventional piping architectures • Higher inherent reliability • Invented by Einstein and Szilard

ALIP↗

All-AC, building integrated photovoltaic system for mass deployment of residential photovoltaic systems

Solar Red is developing novel PV installation methods and system designs that lower costs dramatically and allow seamless integration into the structure of any sloped roof using existing construction tools and processes. The overall objective of this project is to address the greatest barriers to massive adoption of residential and small commercial rooftop solar – scalability of installation and total cost of ownership - by moving Solar Red’s snap-in/snap-out PV installation method from the pre-prototype design phase to the development and construction of a deployed prototype system.

14 SOLAR ENERGY↗

Non-Linear Transmission Line (NLTL) Microwave Source Lecture Notes the United States Particle Accelerator School

We will quickly go through the history of the non-linear transmission lines (NLTLs). We will describe how they work, how they are modeled and how they are designed. Note that the field of high power, NLTL microwave sources is still under development, so this is just a snap shot of their current state. Topics discussed are: (1) Introduction to solitons and the KdV equation; (2) The lumped element non-linear transmission line; (3) Solution of the KdV equation; (4) Non-linear transmission lines at microwave frequencies; (5) Numerical methods for NLTL analysis; (6) Unipolar versus bipolar input; (7) High power NLTL pioneers; (8) Resistive versus reactive load; (9) Non-lineaer dielectrics; and (10) Effect of losses.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Metal Matrix Microencapsulated (M3) fuel neutronics performance in PWRs

Metal Matrix Microencapsulated (M3) fuel consists of TRISO or BISO coated fuel particles directly dispersed in a matrix of zirconium metal to form a solid rod (Fig. 1). In this integral fuel concept the cladding tube and the failure mechanisms associated with it have been eliminated. In this manner pellet-clad-interactions (PCI), thin tube failure due to oxidation and hydriding, and tube pressurization and burst will be absent. M3 fuel, given the high stiffness of the integral rod design, could as well improve grid-to-rod wear behavior. Overall M3 fuel, compared to existing fuel designs, is expected to provide greatly improved operational performance. Multiple barriers to fission product release (ceramic coating layers in the coated fuel particle and te metal matrix) and the high thermal conductivity zirconium alloy metal matrix contribute to the enhancement in fuel behavior. The discontinuous nature of fissile material encapsulated in coated particles provides additional assistance; for instance if the M3 fuel rod is snapped into multiple pieces, only the limited number of fuel particles at the failure cross section are susceptible to release fission products. This is in contrast to the conventional oxide fuel where the presence of a small opening in the cladding provides the pathway for release of the entire inventory of fission products from the fuel rod. While conventional metal fuels (e.g. U-Zr and U-Mo) are typically expected to experience large swelling under irradiation due to the high degree of damage from fission fragments and introduction of fission gas into the lattice, this is not the case for M3 fuels. The fissile portion of the fuel is contained within the coated particle where enough room is available to accommodate fission gases and kernel swelling. The zirconium metal matrix will not be exposed to fission products and its swelling is known to be very limited when exposed solely to neutrons. Under design basis RIA and LOCA, fuel performance will be superior to the conventional oxide fuel since PCMI and rod burst, respectively, have been mitigated. Under beyond design basis accident scenarios where the fuel is exposed to high temperature steam for prolonged periods, larger inventory of zirconium metal in the core could negatively affect the accident progression. A thin steam resistant layer (e.g. alumina forming alloy steel), integrated into the solid rod during fabrication by co-extrusion or hot-isostatic-pressing, offers the potential to provide additional fuel protection from steam interaction: blanketing under a range of boiling regimes and under severe accident conditions up to high temperatures well beyond what is currently possible in the conventional fuel. A crucial aspect to the viability of M3 fuel in light water reactors is the reduced heavy metal load compared to standard pellet fuel. This study evaluated the design requirements to operate a Pressurized Water Reactor (PWR) with M3 fuel in order to obtain fuel cycle length, reactivity coefficients, and power peaking factors comparable to that of standard fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Unusual Light in Dark Space Revealed by Los Alamos, NASA

By looking at the dark spaces between visible galaxies and stars the NASA/JPL CIBER sounding rocket experiment has produced data that could redefine what constitutes a galaxy. CIBER, the Cosmic Infrared Background Experiment, is designed to understand the physics going on between visible stars and galaxies. The relatively small, sub-orbital rocket unloads a camera that snaps pictures of the night sky in near-infrared wavelengths, between 1.2 and 1.6 millionth of a meter. Scientists take the data and remove all the known visible stars and galaxies and quantify what is left.

79 ASTRONOMY AND ASTROPHYSICS↗

Final Muon Emittance Exchange in Vacuum for a Collider

We outline a plan for final muon ionization cooling with quadrupole doublets focusing onto short absorbers followed by emittance exchange in vacuum to achieve the small transverse beam sizes needed by a muon collider. A flat muon beam with a series of quadrupole doublet half cells appears to provide the strong focusing required for final cooling. Each quadrupole doublet has a low β region occupied by a dense, low Z absorber. After final cooling, normalized xyz emittances of (0.071, 0.141, 2.4) mm-rad are exchanged into (0.025, 0.025, 70) mm-rad. Thin electrostatic septa efficiently slice the bunch into 17 parts. The 17 bunches are interleaved into a 3.7 meter long train with RF deflector cavities. Snap bunch coalescence combines the muon bunch train longitudinally in a 21 GeV ring in 55 μs, one quarter of a synchrotron oscillation period. A linear long wavelength RF bucket gives each bunch a different energy causing the bunches to drift until they merge into one bunch and can be captured in a short wavelength RF bucket with a 13% muon decay loss and a packing fraction as high as 87%.

43 PARTICLE ACCELERATORS↗

Self-assembling segmented coiled tubing

Self-assembling segmented coiled tubing is a concept that allows the strength of thick-wall rigid pipe, and the flexibility of thin-wall tubing, to be realized in a single design. The primary use is for a drillstring tubular, but it has potential for other applications requiring transmission of mechanical loads (forces and torques) through an initially coiled tubular. The concept uses a spring-loaded spherical `ball-and-socket` type joint to interconnect two or more short, rigid segments of pipe. Use of an optional snap ring allows the joint to be permanently made, in a `self-assembling` manner.

15 GEOTHERMAL ENERGY↗

Evaluation of Installation Time for SMASHmount by SMASHsolar

The Department of Energy SunShot Incubator program provides early-stage assistance to help startup companies cross technological barriers to commercialization while encouraging private sector investment. The SunShot Incubator program aims to shorten the time it takes for a young business or company to develop an innovative product concept and make it commercially available, which includes product prototyping, deployment, and, potentially, manufacturing. SMASHsolar was selected as an Incubator awardee to develop a simple, snap-together, module-integrated photovoltaic (PV) mounting system in attempts to dramatically reduce the time, effort and skill needed to install rooftop solar. In support of this award, the National Renewable Energy Laboratory worked with SMASHsolar to develop a procedure for evaluating the installation time required for the SMASHmount system vs. widely-available rail systems. Amongst several installations, NREL measured the following installation times, subject to the qualifications and conditions described later in this report. NREL found that the SMASHsolar SMASHmount system was installed between 15% and 37% faster than tested competing systems after one or two installations of the system.

14 SOLAR ENERGY↗

Sensing, interlocking solar module system and installation method

A solar module system is coupled directly to a fixed structure either individually or collectively as an array. Universal mounting brackets attached to the back of each solar panel module each connect to one or more other brackets of adjacent solar panels and/or to mounting feet that anchor to the fixed structure. Mounting brackets interlock with mounting brackets on adjacent solar modules and include a flexible snap coupling mechanism including a locking feature to selectively flexibly connect to and disconnect from other mounting brackets of adjacent solar panels.

14 SOLAR ENERGY↗