Search NASA⌕ Search

SEARCH · Search NASA

Results for “solidification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

A side-by-side comparison of the solidification dynamics of quasicrystalline and approximant phases in the Al–Co–Ni system

Quasicrystals and their approximants have triggered widespread interest due to the challenge of solving their complex crystal structures as well as their possibly exceptional properties. The structural motifs of approximants are similar to those of the corresponding quasicrystals, but to what extent are their crystallization pathways the same? Unfortunately, there have been very few in situ experimental investigations to answer this question. Here, by leveraging the high penetrating power of hard X-rays, synchrotron-based X-ray tomography was conducted in order to capture the nucleation and growth of a decagonal quasicrystal and its related approximant. The combination of data-driven computational analysis with new thermodynamic databases allowed the characterization, with high precision, of the constitutional and kinetic driving forces for crystallization. The experimental results prove that the growth of both crystals from a liquid is dominated by first-order kinetics. Nevertheless, and somewhat surprisingly, significant differences were observed in their rates of nucleation and growth. The reasons for such divergent behaviours are discussed in light of contemporary theories of intermetallic crystallization.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Direct ink writing techniques for in situ gelation and solidification

Direct ink writing (DIW) is an extrusion-based 3D printing method which prints near ambient temperatures and has one of the broadest printable material selections among additive manufacturing techniques. However, DIW uses viscoelastic materials susceptible to collapse during printing. Overall, one promising route to improve the structural integrity of viscoelastic inks is using in situ curing methods to increase the yield strength of the printed structures after deposition. This review summarizes progress in three representative methods of in situ curing for DIW, including ultra-violet-induced crosslinking, rapid cure of reactive ingredients, and flash vaporization of a solution’s solvent to coagulate dissolved polymers.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Solidification of REDC Organics and Airborne Release Fraction Measurements

The Radiochemical Engineering Development Center (REDC) generates various liquid organic wastes from processing irradiated targets to recover heavy elements. In the past, these organics were discharged to the Oak Ridge National Laboratory (ORNL) liquid low-level waste (LLLW) system, along with the aqueous waste. Because of a reduction in aqueous LLLW from other ORNL generators and an increase in the radionuclide concentration, particularly 238 Pu, in the organic waste stream, the organics can no longer be discharged to the LLLW system. The plan is to solidify the liquid organic waste for disposal as solid debris waste. The documented safety analysis for REDC uses an airborne release fraction of 5 x 10 -4 with a respirable fraction of 0.2 for plutonium and other actinides from packaged solid debris waste during a fire scenario, for an overall airborne release fraction/respirable fraction of 10 -4 . Solidifying the organic liquids, either by using PM-199 Organoclay ® or by grouting, would produce solid waste forms with no free liquid, which should qualify for disposal at the Waste Isolation Pilot Plant. The use of Organoclay would be much simpler to implement inside a hot cell. Granular Organoclay can be added to the organic waste solutions until there is a dry layer on top of the liquid and then allowed to cure for a few hours. Grouting the liquids would require using multiple ingredients and mixing steps. Both methods produced waste forms that trapped cerium, as a surrogate for plutonium, inside the waste, with airborne release fractions during fire scenario tests of well below the 10 -4 limit.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Solidification of REDC Organics For Disposal As Solid Waste

The Radiochemical Engineering Development Center (REDC) generates various liquid organic wastes from processing irradiated targets to recover heavy elements. In the past, these organics were discharged to the Oak Ridge National Laboratory (ORNL) liquid low-level waste (LLLW) system, along with the aqueous waste. Because of a reduction in aqueous LLLW from other ORNL generators and an increase in the radionuclide concentration, particularly 238 Pu, in the REDC organic waste stream, the organics can no longer be discharged to the LLLW system. The plan is to solidify the liquid organic waste for disposal as solid waste. Solidifying the organic liquids using PM-199 Organoclay ® would produce solid waste forms with no free liquid, which should qualify for disposal at the Waste Isolation Pilot Plant. Granular Organoclay can be added to the organic waste solutions until there is a dry layer on top of the liquid and then allowed to cure for a few hours to produce a solid wasteform.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

An Ab Initio Molecular Dynamics Study of Key Thermodynamic Input Parameters for Computer Simulation of U-6Nb Solidification

The key to metallic fuel development is the fabrication of uranium metal and alloys into fuel forms. U-Nb alloys are one of the best candidates for a metallic fuel alloy with high-temperature strength sufficient to support the core, acceptable nuclear properties, good fabricability, and compatibility with usable coolant media. Melt processing has been a key component of the metallic fuel cycle, and process models require thermophysical parameters at elevated temperatures, particularly above the melting temperatures, regarding which experimental data are scarce, for accurate simulations and process development. By means of ab initio density-functional theory (DFT) quantum molecular dynamics (QMD), we have calculated the main thermophysical parameters—the density, thermal expansion coefficient, specific heat, thermal conductivity, melting temperature, latent heat of fusion, and viscosity—used in the modeling of the U-6 wt.% Nb alloy casting. The melting temperature of the U-6 wt.% Nb alloy at ambient pressure is obtained by means of QMD simulations using the Z-method. The ambient volume change and latent heat of melting of U-6 wt.% Nb are also derived from QMD simulations in conjunction with analytical fitting for the energy and pressure. The thermal conductivity for the solid U-Nb alloy is calculated from the semi-classical Boltzmann transport equation combined with an estimate of the electron relaxation time obtained from DFT simulations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗