Search NASA⌕ Search

SEARCH · Search NASA

Results for “support structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Development of the structural technology of a large deployable antenna

The current NASA-sponsored Antenna Technology Development Program of the offset wrap-rib antenna concept is based on a ground test program of 'proof of concept' hardware whose potential on-orbit performance is based on analytical estimates. The ground demonstration hardware represents a partial 55-meter diameter reflector and feed support structure. Testing will include automated deployment, reflector surface quality evaluation and validation of analytical performance models. Test results and hardware fabrication costs will be used to refine the models that will be the basis for the preliminary design of a 100-meter diameter wrap-rib antenna system. Additionally, the design, processes, tooling, fabrication techniques, fixturing and assembly approaches used for the 'proof of concept' hardware are directly applicable to building flight systems up to 100 meters in diameter.

Wada, B. K.↗

An analysis of cross-coupling of a multicomponent jet engine test stand using finite element modeling techniques

A two axis thrust measuring system was analyzed by using a finite a element computer program to determine the sensitivities of the thrust vectoring nozzle system to misalignment of the load cells and applied loads, and the stiffness of the structural members. Three models were evaluated: (1) the basic measuring element and its internal calibration load cells; (2) the basic measuring element and its external load calibration equipment; and (3) the basic measuring element, external calibration load frame and the altitude facility support structure. Alignment of calibration loads was the greatest source of error for multiaxis thrust measuring systems. Uniform increases or decreases in stiffness of the members, which might be caused by the selection of the materials, have little effect on the accuracy of the measurements. It is found that the POLO-FINITE program is a viable tool for designing and analyzing multiaxis thrust measurement systems. The response of the test stand to step inputs that might be encountered with thrust vectoring tests was determined. The dynamic analysis show a potential problem for measuring the dynamic response characteristics of thrust vectoring systems because of the inherently light damping of the test stand.

Schweikhard, W. G.↗

Comparison of Structural Concepts for Transport Aircraft with a Tail Cone Turbine

An evaluation of three structural concepts for an advanced aircraft design with a tail cone turbine is presented. Structural models were developed using an innovative rapid finite element modeling tool called Conceptual Design Shop (CDS). CDS is an attempt to fill a gap in current finite element modeling software to automatically connect wings and tails to the fuselage with sufficient support structure in airframe models. For comparison with actual aircraft structures, a model of a transport aircraft design developed using CDS is compared with published structural weight data for a Boeing 737-200. A method for computing aerodynamic stability parameters from an MSC/NASTRAN finite element analysis output deck is also discussed. Finally, the weight effects for using a tail cone turbine in an advanced transport aircraft design are evaluated by comparing three composite structural models, for which component thicknesses and cross-sections are sized by the Hypersizer software.

Mason, Brian H.↗

Polymeric peptide pigments with sequence-encoded properties

Melanins are a family of heterogeneous polymeric pigments that provide ultraviolet (UV) light protection, structural support, coloration, and free radical scavenging. Formed by oxidative oligomerization of catecholic small molecules, the physical properties of melanins are influenced by covalent and noncovalent disorder. We report the use of tyrosine-containing tripeptides as tunable precursors for polymeric pigments. In these structures, phenols are presented in a (supra-)molecular context dictated by the positions of the amino acids in the peptide sequence. Oxidative polymerization can be tuned in a sequence-dependent manner, resulting in peptide sequence–encoded properties such as UV absorbance, morphology, coloration, and electrochemical properties over a considerable range. Short peptides have low barriers to application and can be easily scaled, suggesting near-term applications in cosmetics and biomedicine.

36 MATERIALS SCIENCE↗

From Structured Solvents to Hybrid Materials (SS2HM) for Chemically Selective Capture and Electromagnetic Release of CO 2 : Mechanisms, Stability and Interfaces (Final Report)

The goal of this research program was to develop high capacity sorbents amenable for alternative regeneration approaches for direct air capture (DAC) of CO 2 . In particular, the research aimed to develop an understanding of CO 2 binding mechanism, thermal and oxidative stability, and regeneration energetics of functionalized ionic liquids (ILs), deep eutectic solvents (DESs), and porous materials. ILs and DESs are high-dielectric solvents with structural tunability that permits the rational-design for energy-efficient regeneration approaches based on electromagnetic (EM) field and moisture-swing. By further incorporating these solvents into polymeric capsules and other structural supports, multi-scale interfaces for targeted CO 2 and energy transfers were achieved. Aspects related to CO 2 capacity, selectivity, stability, dielectric properties, and binding energies were examined through experimental and computational design to identify molecular descriptors to inform future design of structured solvents and hybrid materials for DAC. Enclosed final report details the key findings, science advancements, and workforce development efforts from this project.

36 MATERIALS SCIENCE↗

A cellular glass substrate solar concentrator

The design of a second generation point focusing solar concentration is discussed. The design is based on reflective gores fabricated of thin glass mirror bonded continuously to a contoured substrate of cellular glass. The concentrator aperture and structural stiffness was optimized for minimum concentrator cost given the performance requirement of delivering 56 kWth to a 22 cm diameter receiver aperture with a direct normal insolation of 845 watts sq m and an operating wind of 50 kmph. The reflective panel, support structure, drives, foundation and instrumentation and control subsystem designs, optimized for minimum cost, are summarized. The use of cellular glass as a reflective panel substrate material is shown to offer significant weight and cost advantages compared to existing technology materials.

Bedard, R.↗

Enhanced Activity of Heterogeneous Pd(II) Catalysts on Acid-Functionalized Metal–Organic Frameworks

Single-site heterogeneous catalysts (SSHCs) play important roles in fundamental science and technology, owing to the molecular level control of structure–support interactions that is possible in these systems. Recently, SSHCs supported by acidic oxides have attracted particular interest because catalytically active metal centers can be formed at the surface sites. Here, we incorporated a palladium SSHC in phosphated and sulfated metal–organic frameworks (MOFs), hafnium-based MOF-808 (Hf-MOF-808-PO 4 and Hf-MOF-808-SO 4 ). The structural and electronic properties of the Pd(II) sites coordinated to the acidic sites in these MOFs were investigated through X-ray photoelectron spectroscopy, vibrational spectroscopy, X-ray crystallographic techniques, catalytic studies, and quantum mechanical electronic structure calculations employing density functional theory. We demonstrated that the presence of node-bound acidic functional groups stabilizes the Pd(II) site in these MOFs, resulting in enhanced catalytic activities (compared to in the nonacid functionalized Hf-MOF-808) in the oxidative Heck reaction where Pd(II) is the active species. The density functional calculations support the interpretation that the acid functionalization of the MOF node can stabilize the Pd(0) intermediate state during the catalytic reactions, thereby suppressing Pd(0) aggregation leading to catalyst deactivation. Furthermore, these findings offer insights and methodology for the catalytic investigation of SSHCs in MOFs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-performance deployable structures for the support of high-concentration ratio solar array modules

A study conducted on high-performance deployable structures for the support of high-concentration ratio solar array modules is discussed. Serious consideration is being given to the use of high-concentration ratio solar array modules or applications such as space stations. These concentrator solar array designs offer the potential of reduced cost, reduced electrical complexity, higher power per unit area, and improved survivability. Arrays of concentrators, such as the miniaturized Cassegrainian concentrator modules, present a serious challenge to the structural design because their mass per unit area (5.7 kg/square meters) is higher than that of flexible solar array blankets, and the requirement for accurate orientation towards the Sun (plus or minus 0.5 degree) requires structures with improved accuracy potentials. In addition, use on a space station requires relatively high structural natural frequencies to avoid deleterious interactions with control systems and other large structural components. The objective here is to identify and evaluate conceptual designs of structures suitable for deploying and accurately supporting high-concentration ratio solar array modules.

Mobrem, M.↗

Fabrication of strain-isolated ceramic coated combustor components

The use of strain-isolated ceramic coated material to produce an AGT1500 combustor scroll-shaped transition duct which requires no air for film cooling is investigated. The scroll receives the exhaust of the can-style combustor liner and turns it into the annular inlet of the high pressure gas producer turbine nozzle. Strain-isolation of plasma sprayed thermal barrier coating is achieved by placing a compliant pad between the structural base metal and the ceramic coating. The compliant pad is brazed to the metal structure. In order to achieve a good braze bond, the strain-isolating compliant pad and base metal must be closely matched in shape and tightly fixtured for joining. The complex geometry of the AGT1500 scroll makes it impractical to attack pads to the supporting structure in its finished shape. Instead the pads are brazed to flat stock and post-formed into scroll sections. While test samples were successfully post-formed, plasma sprayed, and subjected to cyclic heating, the forming of full scale parts by normal methods resulted in tearing of the Hastelloy-X base metal because of embrittlement by the braze material. Several solutions were explored which finally resulted in the successful forming of full scale scroll parts.

Rutter, S.↗

Structural Qualification Testing of the WindSat Payload Using Sine Bursts Near Structural Resonance

Sine burst tests are often used for structural qualification of space flight hardware. In most instances, the driving frequency of the shaker is specified far below the structure's first resonant mode, such that the entire test article sees uniform acceleration. For large structures, this limits qualification testing to lower parts of the structure, or else it over-tests the lower structure to achieve qualification of the upper structure. The WindSat payload, a 10.5 foot tall graphite/epoxy, titanium, and aluminum radiometer, experiences accelerations at the six foot diameter reflector nearly four times that at the spacecraft interface. Due to size of the payload, the number of bonded joints, and the lightweight reflector support structure design and construction, using static pull testing to qualify all of the bonded joints in the upper structure would result in large, expensive, and extensive test fixturing. Sine burst testing near the first two structural resonant modes was performed on the WindSat payload to achieve the correct load factor distribution up the stack for structural qualification. In this presentation, how finite element method (FEM) sine burst predictions were used in conjunction with low level random and sine burst tests to achieve correct qualification test load factor distribution on the WindSat payload is discussed. Also presented is the risk mitigation approach for using the uncorrelated FEM in this procedure.

Pontius, Jim↗

MRS Modelling in OpenFAST

Multi-rotor wind turbines, where more than one rotor is connected to a single support structure, are increasing in popularity due to their balance of power generation with component size, weight, and cost. Multi-rotor turbines are also common in marine energy, where deployment sites tend to be depth-constrained, limiting the maximum size of a rotor. To support the industry and research communities in designing and modeling multi-rotor turbines, the open-source turbine modeling tool OpenFAST, developed and supported by the National Renewable Energy Laboratory, is being extended to model multi-rotor wind and marine turbines. This presentation gives an overview of the current state of OpenFAST, planned changes to enable coupled aero-hydro-servo-elastic dynamic modeling of multi-rotor turbines, and examples of the types of turbines that OpenFAST will support.

marine energy↗

Spinel oxides as coke-resistant supports for NiO-based oxygen carriers in chemical looping combustion of methane

Due to their high activity for methane conversion under a cyclic redox scheme, supported nickel oxides are among the most extensively investigated oxygen carrier materials for chemical looping combustion (CLC) and reforming (CLR) of methane. However, coke formation remains as a key challenge for Ni-containing oxygen carriers. The current study investigates the effect of reducible, spinel-structured supports to enhance coke resistance of NiO-based oxygen carriers. It was hypothesized that reducible supports capable of continued yet slow lattice oxygen donation in the presence of methane can actively retard coke formation on the surface of the oxygen carriers. To evaluate such effects, NiFe 2 O 4 , MgFe 2 O 4 , and BaFe 2 O 4 are investigated as coke-resistant, reducible supports for NiO using mass spectrometry (MS) and thermogravimetric analysis (TGA) during chemical looping cycles. All three reducible supports were capable of continuous oxygen donation over an extended period of time (>40 min) without signs of coke formation. Further, when used as supports for NiO, the resulting oxygen carriers showed no sign of carbon deposition under typical methane CLC environments. In comparison, NiO supported on inert MgAl 2 O 4 exhibited significant coke formation after only 2.5 min. Moreover, NiO supported on NiFe 2 O 4 and BaFe 2 O 4 exhibited faster redox activity and higher oxygen carrying capacity when compared to the inert MgAl 2 O 4 -supported NiO. Detailed investigation of the reduction behavior of NiFe 2 O 4 -supported NiO revealed extensive solid-state reactions and Ni/Fe exchanges among the support, NiO, and newly formed phases. Specifically, initial weight loss in NiFe 2 O 4 -supported NiO was associated with reduction of the oxygen carrier to metallic Ni and Fe 3 O 4 phases. Subsequent coke inhibition was attributed to the slow reduction of Fe 3 O 4 and FeO phases. Multi-cyclic redox studies indicated that NiFe 2 O 4 -supported NiO gradually lost its redox activity. In comparison, both MgFe 2 O 4 - and BaFe 2 O 4 -supported NiO exhibited satisfactory redox stability, activity, and coke resistance.

03 NATURAL GAS↗

High Velocity Joining of Multi-material Stacks Containing 3rd Generation Advanced High-Strength Stainless Steel and Aluminum Extrusion and Casting (Abstract)

Advanced lightweight materials, including multi-phase steels, aluminum extrusions and aluminum castings, have increasingly replaced mild steel to meet original equipment manufacturer (OEM) demand for increased fuel economy and crash-safety requirements. Third Generation (Gen 3) AHSS provides a superior combination of strength and ductility for crash energy management components in the vehicle body-in-white (BIW). Aluminum extrusions are widely used for bumper, door rocker panel, cradle and battery frame applications. Aluminum castings are increasingly being used in electric vehicles to provide part consolidation, weight saving and increased driving range. Rocker panels are, for example, an important component of the battery electric vehicle (BEV) body structure. The rocker panel serves several purposes, including structural support, crash resistance, protection for the vehicle's underbody and battery tray, and contributing to the overall aesthetics. In order to reduce weight, rocker panels are usually constructed using outer panels consisting of 3rd generation advanced high strength steels (AHSS) and an inner multicell aluminum extrusion structure for energy absorption which protects the batteries in a crash event. It is well known, however, that these material combinations provide significant challenges for joining and are susceptible to liquid metal embrittlement and loss of strength. The overall goal is to find a solution that addresses these challenges in order to produce multi-material vehicle components with reduced weight and minimal galvanic and recyclability issues. The approach being proposed here is to utilize a novel high velocity (HiVe) riveting and clinching technique recently demonstrated by Pacific Northwest National Laboratory (PNNL) to join (2T/3T) sheets of aluminum alloys and steel. This process will not only address the aforementioned challenges but also help significantly reduce the joining cycle time. This work will also demonstrate use of HiVe assemblies to be retrofitted to existing body-shop robots thus having minimal impact to existing body shop operations.

36 MATERIALS SCIENCE↗

Alignment and Testing of Critical Interface Fixtures for the James Webb Space Telescope

NASA's James Webb Space Telescope (JWST) is a 6.6m diameter, segmented, deployable telescope for cryogenic IR space astronomy. The JWST Observatory architecture includes the Primary Mirror Backplane Support Structure (PMBSS) and Integrated Science Instrument Module (ISIM) Electronics Compartment (IEC) which is designed to integrate to the spacecraft bus via six cup/cone interfaces. Prior to integration to the spacecraft bus the JWST observatory must undergo environmental testing, handling, and transportation. Multiple fixtures were developed to support these tasks including the vibration fixture and handling and integration fixture (HIF). This work reports on the development of the nominal alignment of the six interfaces and metrology operations performed for the JWST observatory to safely integrate them for successful environmental testing.

technology development↗

Alignment and Testing of Critical Interface Fixtures for the James Webb Space Telescope

NASAs James Webb Space Telescope (JWST) is a 6.6m diameter, segmented, deployable telescope for cryogenic IR space astronomy. The JWST Observatory architecture includes the Primary Mirror Backplane Support Structure (PMBSS) and Integrated Science Instrument Module (ISIM) Electronics Compartment (IEC) which is designed to integrate to the spacecraft bus via six cupcone interfaces. Prior to integration to the spacecraft bus the JWST observatory must undergo environmental testing, handling, and transportation. Multiple fixtures were developed to support these tasks including the vibration fixture and handling and integration fixture (HIF). This work reports on the development of the nominal alignment of the six interfaces and metrology operations performed for the JWST observatory to safely integrate them for successful environmental testing.

instrument development↗

Field Quality Study of the LARP Nb3Sn 3.7m-Long Quadrupole Models of LQ Series

After the successful test of the first long Nb{sub 3}Sn quadrupole magnet (LQS01), the US LHC Accelerator Research Program (LARP) has assembled and tested a new 3.7 m-long Nb{sub 3}Sn quadrupole (LQS02). This magnet has four new coils made of the same conductor as LQS01 coils, and it is using the same support structure. LQS02 was tested at the Fermilab Vertical Magnet Test Facility with the main goal to confirm that the long models can achieve field gradient above 200 T/m, LARP target for 90-mm aperture, as well as to measure the field quality. These long models lack some alignment features and it is important to study the field harmonics. Previous field quality measurements of LQS01 showed higher than expected differences between measured and calculated harmonics compared to the short models (TQS) assembled in a similar structure. These differences could be explained by the use of two different impregnation fixtures during coil fabrication. In this paper, we present a comparison of the field quality measurements between LQS01 and LQS02 as well as a comparison with the short TQS models. If the result supports the coil fabrication hypothesis, another LQS assembly with all coils fabricated in the same fixture will be produced for understanding the cause of the discrepancy between short and long models.

43 PARTICLE ACCELERATORS↗

Flight support system mechanisms

The Flight Support System (FSS) which contains twelve mechanisms (six different types) which are used for retention and positioning of a Multimission Modular Spacecraft (MMS) within the Space Shuttle's cargo bay during launch, retrieval, and servicing missions is described. Retention latches were designed to provide the capability for structural support of the MMS during launch and retrieval, and during servicing operations the mechanisms on the Positioning Platform provide the capability for positioning the MMS in virtually any orientation necessary for the work to be performed. In addition, there are mechanisms for matching and demating umbilical connectors and a mechanism for locking the Positioning Platform during maneuvers. Each Mechanism is driven by a Common Drive Unit. Manual overrides were provided for those mechanisms that would present a safety hazard for the crew, if they should fail.

Source record↗

Structural Analysis of the Support System for a Large Compressor Driven by a Synchronous Electric Motor

For economic reasons, the steam drive for a large compressor was replaced by a large synchronous electric motor. Due to the resulting large increase in mass and because the unit was mounted on a steel frame approximately 18 feet above ground level, it was deemed necessary to determine if a steady state or transient vibration problem existed. There was a definite possibility that a resonant or near resonant condition could be encountered. The ensuing analysis, which led to some structural changes as the analysis proceeded, did not reveal any major steady state vibration problems. However, the analysis did indicate that the system would go through several natural frequencies of the support structure during start-up and shutdown. This led to the development of special start-up and shutdown procedures to minimize the possibility of exciting any of the major structural modes. A coast-down could result in significant support structure and/or equipment damage, especially under certain circumstances. In any event, dynamic field tests verified the major analytical results. The unit has now been operating for over three years without any major vibration problems.

Winter, J. R.↗