SEARCH · Search NASA

Results for “surface stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

All sources NASA NTRS DOE OSTI

NASA NTRS1974

Preliminary performance estimates of a highly maneuverable remotely piloted vehicle

A computerized synthesis program has been used to assess the effects of various vehicle and mission parameters on the performance of a highly maneuverable remotely piloted vehicle (RPV) for the air-to-air combat role. The configuration used in the study is a trapezoidal-wing and body concept, with forward-mounted stabilizing and control surfaces. The study mission consists of an outbound cruise, an acceleration phase, a series of subsonic and supersonic turns, and a return cruise. Performance is evaluated in terms of both the required vehicle weight to accomplish this mission and combat effectiveness as measured by turning and acceleration capability. The report describes the synthesis program, the mission, the vehicle, and the results of sensitivity and trade studies.

Nelms, W. P., Jr.↗

NASA NTRS1974

RSRA sixth scale wind tunnel test

The sixth scale model of the Sikorsky/NASA/Army rotor systems research aircraft was tested in an 18-foot section of a large subsonic wind tunnel for the purpose of obtaining basic data in the areas of performance, stability, and body surface loads. The model was mounted in the tunnel on the struts arranged in tandem. Basic testing was limited to forward flight with angles of yaw from -20 to +20 degrees and angles of attack from -20 to +25 degrees. Tunnel test speeds were varied up to 172 knots (q = 96 psf). Test data were monitored through a high speed static data acquisition system, linked to a PDP-6 computer. This system provided immediate records of angle of attack, angle of yaw, six component force and moment data, and static and total pressure information. The wind tunnel model was constructed of aluminum structural members with aluminum, fiberglass, and wood skins. Tabulated force and moment data, flow visualization photographs, tabulated surface pressure data are presented for the basic helicopter and compound configurations. Limited discussions of the results of the test are included.

Flemming, R.↗

NASA NTRS1979

Phase Two of the Array Automated Assembly Task for the Low Cost Solar Array Project

Various top contact metal systems were studied. Only Ti Pd Cu approaches baseline (Ti Pd Ag) quality, but this system shows a lack of long term stability. Aluminum back surface field structures were fabricated and thicknesses of p superscript + material of up to 7.0 microns were achieved with open circuit voltages of 0.59V. A general purpose ultrasonic welder was purchased and tests using various metal foils are under way. During fabrication of the demonstration module, several cells became cracked. Due to redundancy of interconnections, the module was not open circuited but the efficiency was reduced to 8.8%. The broken cell was interconnected with a strap across the back and the efficiency was increased to 11.5%. A cost analysis was made and the results indicate a selling price of $0.56/watt peak (in 1986 with 1975 dollars).

Campbell, R. B.↗

NASA NTRS1980

New class of asymmetric shapes of rotating liquid drops

Shapes and stability of surface-tension-endowed drops rotating rigidly at fixed angular momentum are calculated by finite-element analysis. A new family of asymmetric two-lobed drop shapes is discovered that branches from, and rejoins, the Pik-Pichak family of symmetric two-lobed shapes. The computations are verified for axisymmetric and symmetric two-lobed drop shape by comparison with previous approximations.

Brown, R. A.↗

NASA NTRS1980

Sunspots and the physics of magnetic flux tubes. X - On the hydrodynamic instability of buoyant fields

The hydrodynamics of cylindrical buoyant bubbles (magnetic flux tubes) in an atmosphere is examined. Their dynamical stability is considered, with particular attention to the Rayleigh-Taylor and Kelvin-Helmholtz instabilities. The instabilities are sufficient to cause fragmentation in the absence of some strong stabilizing effect such as surface tension or an internal azimuthal magnetic field. The results of the stability analysis are first applied to rising gas bubbles in liquids. Then, since agreement with the experimental data is found, the results are applied to the similar problem of the rising magnetic flux in the sun. Magnetic flux tubes in a fluid velocity field are intrinsically unstable, unless twisted. With the known dynamical limits on the degree of twisting, an upper limit on the diameter of the order of a few hundred kilometers is found for the stability of individual flux tubes in the photosphere. Observations show that tubes, except when clustered to form sunspots, are generally not larger than this amount. Therefore, it is suggested that the hydrodynamic instability of larger tubes is a prime cause of their absence from the solar photosphere.

Tsinganos, K. C.↗

NASA NTRS1984

Damping Seals for Turbomachinery

Seals with rough surfaces proposed for stabilizing shaft motion and preventing leakage along shaft in machines such as turbopumps. Applicable to turbomachinery with speed limits raised and bearing life extended, avoiding costly shutdowns.

Von Pragenau, G. L.↗

NASA NTRS1982

Feasibility study of solid surface subreflector production techniques

The principal effort was to study technical feasibility and cost aspects of the production technique of spin forming a subreflector reflective surface to a desired surface of revolution, back the surface with fiberglass to stabilize it sufficiently so that it may be machined to the target surface tolerance of .008 inches Root Mean Square (RMS) with a goal of .003 inches RMS. To verify this production technique, analyses was performed to define the production procedure. A price estimate for a 150 inch diameter subreflector for a 34 meter cassegrain antenna. During this feasibility study, numerous production processes were evaluated theoretically as production approaches for single surface, non-welded subreflectors. The first successful was the principal process of spin forming the reflective surface, backing with fiberglass and machining to a final contour. The second successful process was spin forming or bump forming a thicker reflective surface, with an integral (welded in) structure as a backing and machining the mounting pads and reflector to a final configuration.

Source record↗

NASA NTRS1983

Transonic Airfoil Development

This lecture consists of three parts, in which discussions are presented of the current state of development of transonic or supercritical airfoils designed for fully turbulent boundary layers on the surfaces, previous research on subcritical airfoils designed to achieve laminar boundary layers on all or parts of the surfaces, and current research on supercritical airfoils designed to achieve laminar boundary layers. In the first part the use of available two dimensional computer codes in the development of supercritical airfoils and the general trends in the design of such airfoils with turbulent boundary layers are discussed. The second part provides the necessary background on laminar boundary layer phenomena. The last part, which constitutes the major portion of the lecture, covers research by NASA on supercritical airfoils utilizing both decreasing pressure gradients and surface suction for stabilizing the laminar boundary layer. An investigation of the former has been recently conducted in fight using gloves on the wing panels of the U.S. Air Force F111 TACT airplane, research on the later is currently being conducted in a transonic wind tunnel which has been modified to greatly reduce the stream turbulence and noise levels in the tests section.

Whitcomb, R. T.↗

NASA NTRS1984

Leading edge flap system for aircraft control augmentation

Traditional roll control systems such as ailerons, elevons or spoilers are least effective at high angles of attack due to boundary layer separation over the wing. This invention uses independently deployed leading edge flaps on the upper surfaces of vortex stabilized wings to shift the center of lift outboard. A rolling moment is created that is used to control roll in flight at high angles of attack. The effectiveness of the rolling moment increases linearly with angle of attack. No adverse yaw effects are induced. In an alternate mode of operation, both leading edge flaps are deployed together at cruise speeds to create a very effective airbrake without appreciable modification in pitching moment. Little trim change is required.

Rao, D. M.↗

NASA NTRS1985

Precision space structures

NASA large space structures efforts to date aimed towards large, flexible antenna-like structures (30-100M) with relatively long wavelengths (1-30cm) and moderate disturbances leading to some structure-control interaction. Potential missions in the OPTICS regime require small reflectors/mirrors, short wavelengths (visible to 100 microns), very tight tolerances in surface, alignment, pointing stability, as well as the potential of considerable on-board disturbances. For optics systems: figure/surface control can be quasi-static, active/passive isolation schemes are possible, vibration control is necessary, and the attitude control system can be low BW - Ground testing of reflectors and mirrors is more feasible than with antennas.

Soosaar, K.↗

NASA NTRS1985

Investigation of Low-temperature Solders for Cryogenic Wind Tunnel Models

The advent of high Reynolds number cryogenic wind tunnels has forced alteration of manufacturing and assembly techniques and eliminated usage of many materials associated with conventional wind tunnel models. One of the techniques affected is soldering. Solder alloys commonly used for wind tunnel models are susceptible to low-temperature embrittlement and phase transformation. The low-temperature performance of several solder alloys is being examined during research and development activities being conducted in support of design and fabrication of cryogenic wind tunnel models. Among the properties examined during these tests are shear strength, surface quality, joint stability, and durability when subjected to dynamic loading. Results of these tests and experiences with recent models are summarized.

Firth, G. C.↗

NASA NTRS1987

Evaluation of industrial platinum resistance thermometers

The calibration and stability of four surface temperature measuring industrial platinum resistance thermometers for use in the temperature range -120 C to 160 C was investigated. It was found that the calibration formulation of the International Practical Temperature Scale of 1968 provided the most accurate calibration. It was also found that all the resistance thermometers suffered from varying degrees of instability and hysteresis.

Daryabeigi, Kamran↗

NASA NTRS1988

Characterization of cobalt(II) chloride-modified condensation polyimide films

The effect of solvent extraction on the properties of cobalt(II) chloride-modified polyimide films was investigated. Solvent-cast films were prepared from solutions of cobalt chloride in poly(amide acid)/N,N-dimethylacetamide (DMAc) and were subsequently dried and cured in static air, forced air, or inert gas ovens with controlled humidity. The films were extracted by either of the three processes (1) soaking in a tray with distilled water at room temperature, (2) soxhlett extraction with distilled water, or (3) soxhell extraction with DMAc. Extraction with DMAc was found to remove both cobalt and chlorine from the films and to slightly increase bulk thermal stability and both surface resistivity and electrical resistivity.

Rancourt, J. D.↗

NASA NTRS1991

Nonlinear evolution of accretion disks induced by radiative feedback processes

The existence of accretion disks around young stellar objects has recently become widely accepted. The luminosity of some young stellar objects is highly variable and is generally attributed to the release of gravitational energy from matter funneled onto them by accretion disks. The inward transport of matter through these disks is coupled to the outward transfer of angular momentum. This transfer is most likely to be regulated by the mixing of adjacent annuli through the process of large-scale turbulence. Most of the accretion energy generated by this process emerges near the inner edge of the disk. This radiation may be intercepted by the disk and may modify the vertical and viscous evolution of the disk itself. If surface heating can stabilize the disk against the dominant viscous process, then in systems with large accretion rates, angular momentum transport and mass flow through the disk will be quenched. Using this result, it is shown that such a mechanism can induce feedback through the disk which produces oscillations in the luminosity of the central object. This oscillation can become chaotic in certain regimes and might thus explain the highly variable nature of many T Tauri systems and their outbursting counterparts: the FU Orionis objects.

Bell, K. R.↗

NASA NTRS1992

Origin and evolution of planetary atmospheres

This report concerns several research tasks related to the origin and evolution of planetary atmospheres and the large-scale distribution of volatile elements in the Solar System. These tasks and their present status are as follows: (1) we have conducted an analysis of the volatility and condensation behavior of compounds of iron, aluminum, and phosphorus in the atmosphere of Venus in response to publish interpretations of the Soviet Venera probe XRF experiment data, to investigate the chemistry of volcanic gases, injection of volatiles by cometary and asteroidal impactors, and reactions in the troposphere; (2) we have completed and are now writing up our research on condensation-accretion modeling of the terrestrial planets; (3) we have laid the groundwork for a detailed study of the effects of water transport in the solar nebula on the bulk composition, oxidation state, and volatile content of preplanetary solids; (4) we have completed an extensive laboratory study of cryovolcanic materials in the outer solar system; (5) we have begun to study the impact erosion and shock alteration of the atmosphere of Mars resulting from cometary and asteroidal bombardment; and (6) we have developed a new Monte Carlo model of the cometary and asteroidal bombardment flux on the terrestrial planets, including all relevant chemical and physical processes associated with atmospheric entry and impact, to assess both the hazards posed by this bombardment to life on Earth and the degree of cross-correlation between the various phenomena (NO(x) production, explosive yield, crater production, iridium signature, etc.) that characterize this bombardment. The purpose of these investigations has been to contribute to the developing understanding of both the dynamics of long-term planetary atmosphere evolution and the short-term stability of planetary surface environments.

Lewis, John S.↗

NASA NTRS1992

A preliminary assessment of the Titan planetary boundary layer

Results of a preliminary assessment of the characteristic features of the Titan planetary boundary are addressed. These were derived from the combined application of a patched Ekman surface layer model and Rossby number similarity theory. Both these models together with Obukhov scaling, surface speed limits and saltation are discussed. A characteristic Akman depth of approximately 0.7 km is anticipated, with an eddy viscosity approximately equal to 1000 sq cm/s, an associated friction velocity approximately 0.01 m/s, and a surface wind typically smaller than 0.6 m/s. Actual values of these parameters probably vary by as much as a factor of two or three, in response to local temporal variations in surface roughness and stability. The saltation threshold for the windblown injection of approximately 50 micrometer particulates into the atmosphere is less than twice the nominal friction velocity, suggesting that dusty breezes might be an occassional feature of the Titan meteorology.

Allison, Michael↗

NASA NTRS1992

Genesis of mobile troughs in the upper westerlies

Stability calculations on basic-state velocity profiles representative of the preferred regions for the development of the upper-level disturbances active in Type B cyclogenesis show that conditions in these regions (weak low-level baroclinicity, large low-level static stability, and large surface roughness) are favorable for the growth of baroclinic waves with maximum amplitude near the tropopause. The structure of these waves compares favorably with observations of developing short-wavelength upper-level troughs in the atmosphere. Basic states characteristic of the storm track regions (strong low-level baroclinicity and small surface roughness) favor the development of baroclinic waves with maximum amplitude at the surface. The dynamics of both the surface-trapped and the upper-tropospheric waves can be interpreted concisely using concepts of potential vorticity. Based on these results, a possible mechanism for Type B cyclogenesis in the storm track regions is proposed that involves the propagation and structural modification of baroclinic wave packets in a zonally varying basic flow.

Whitaker, Jeffrey S.↗

NASA NTRS1994

Desulfurization Of Gas-Turbine Blades

Sulfur removed from nickel-base superalloy used to make gas-turbine blades by heating alloy and simultaneously subjecting it to sputtering by directed Ar(Sup+) ions from ion gun or from glow discharge. Reduction of sulfur content of superalloy by factor of 10 increases lifetime of turbine blade made of alloy by similar factor, because stability of protective surface oxide formed during operation of turbine increased.

Outlaw, Ronald A.↗