Search NASA⌕ Search

SEARCH · Search NASA

Results for “COMPRESSION BUCKLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Implementation of Fiber Optic Sensing System on Sandwich Composite Cylinder Buckling Test

The National Aeronautics and Space Administration (NASA) Engineering and Safety Center Shell Buckling Knockdown Factor Project is a multicenter project tasked with developing new analysis-based shell buckling design guidelines and design factors (i.e., knockdown factors) through high-fidelity buckling simulations and advanced test technologies. To validate these new buckling knockdown factors for future launch vehicles, the Shell Buckling Knockdown Factor Project is carrying out structural testing on a series of large-scale metallic and composite cylindrical shells at the NASA Marshall Space Flight Center (Marshall Space Flight Center, Alabama). A fiber optic sensor system was used to measure strain on a large-scale sandwich composite cylinder that was tested under multiple axial compressive loads up to more than 850,000 lb, and equivalent bending loads over 22 million in-lb. During the structural testing of the composite cylinder, strain data were collected from optical cables containing distributed fiber Bragg gratings using a custom fiber optic sensor system interrogator developed at the NASA Armstrong Flight Research Center. A total of 16 fiber-optic strands, each containing nearly 1,000 fiber Bragg gratings, measuring strain, were installed on the inner and outer cylinder surfaces to monitor the test article global structural response through high-density real-time and post test strain measurements. The distributed sensing system provided evidence of local epoxy failure at the attachment-ring-to-barrel interface that would not have been detected with conventional instrumentation. Results from the fiber optic sensor system were used to further refine and validate structural models for buckling of the large-scale composite structures. This paper discusses the techniques employed for real-time structural monitoring of the composite cylinder for structural load introduction and distributed bending-strain measurements over a large section of the cylinder by utilizing unique sensing capabilities of fiber optic sensors.

FOS↗

Superplastic forming/weld-brazing of titanium skin-stiffened compression panels

A study was conducted to exploit the processing advantages of superplastic forming and weld-brazing for the fabrication of titanium skin-stiffened structural components. Small titanium compression panels were fabricated and tested at room temperature. Stiffeners having configurations of a conventional hat shape, beaded shaped web, ribbed shaped web, or stepped shaped web were investigated. The data from the panel tests included load-shortening curves, local buckling strengths, and failure loads. Experimental buckling loads were compared with buckling loads calculated using a finite-element analysis. The superplastic formed/weld-brazed panels having complex shaped stiffeners developed from 20 to 58 percent higher local buckling strengths than panels with conventionally shaped stiffeners.

Royster, D. M.↗

Effect of Impact Damage and Open Holes on the Compression Strength of Tough Resin/high Strain Fiber Laminates

Tests to assess the performance of composite structures damaged by impact or containing local discontinuities such as cutouts are discussed. In particular, two plate specimen test configurations which were developed to define the serverity of compression strength reduction are described; one for impact damage and the other open hole specimens. The test technique for impact specimens involves damaging the plate at selected energies, measuring the size of damage by ultrasonic C-scan techniques and measuring the residual strength in a compression load test. Open-hole specimen compression tests are conducted for several different hole diameters and the failure strain and load and mode of failure recorded. The plate specimen used in these tests is designed with length, width, thickness and laminate stiffness to ensure that overall plate buckling is not responsible for initiating failure.

Williams, J. G.↗

Analysis and test of superplastically formed titanium hat-stiffened panels under compression

Four hat-stiffened titanium panels with two different stiffener configurations were fabricated by superplastic forming/weld brazing and tested under a moderately heavy compressive load. The panels had the same overall dimensions but differed in the shape of the hat-stiffener webs; three panels had stiffeners with flat webs and the other panel had stiffeners with beaded webs. Analysis indicated that the local buckling strain of the flat stiffener web was considerably lower than the general panel buckling strain or cap buckling strain. The analysis also showed that beading the webs of the hat stiffeners removed them as the critical element for local buckling and improved the buckling strain of the panels. The analytical extensional stiffness and failure loads compared very well with experimental results.

Davis, Randall C.↗

Local buckling and crippling of composite stiffener sections

Local buckling, postbuckling, and crippling (failure) of channel, zee, and I- and J-section stiffeners made of AS4/3502 graphite-epoxy unidirectional tape are studied by experiment and analysis. Thirty-six stiffener specimens were tested statically to failure in axial compression as intermediate length columns. Web width is 1.25 inches for all specimens, and the flange width-to-thickness ratio ranges from 7 to 28 for the specimens tested. The radius of the stiffener corners is either 0.125 or 0.250 inches. A sixteen-ply orthotropic layup, an eight-ply quasi-isotropic layup, and a sixteen-ply quasi-isotropic layup are examined. Geometrically nonlinear analyses of five specimens were performed with the STAGS finite element code. Analytical results are compared to experimental data. Inplane stresses from STAGS are used to conduct a plane stress failure analysis of these specimens. Also, the development of interlaminar stress equations from equilibrium for classical laminated plate theory is presented. An algorithm to compute high order displacement derivatives required by these equations based on the Discrete Fourier Transform (DFT) is discussed.

Bonanni, David L.↗

Experimental and Numerical Analysis of Skin-Stiffener Separation Using a Seven-Point Bend Configuration

Skin-stiffener separation in stiffened composite panels consists of a complex interaction between multiple scales of progressive damage and failure mechanisms. This work used a superposed cohesive element method of modeling resistance curve effects that represents the structural interface of a unidirectional tape skin and a fabric stiffener. Finite element models using cohesive elements with input properties obtained from tape-to-fabric interface characterization tests were compared to experimental results of a stable skin-stiffener separation characterization test using a seven-point bend fixture. This fixture deformed the stiffened panel specimens into a buckled configuration which induced mixed-mode interlaminar stress states at the skin-stiffener interface. The advantage of this fixture was the potential for more stable damage initiation and delamination growth compared to a stringer-stiffened panel under axial compression. Use of the superposed cohesive elements showed promise, but the characterization of interface material properties as input to the cohesive elements remains a crucial component to be investigated to ensure accurate prediction of skin-stiffener separation.

Kosztowny, Cyrus J. R.↗

Implementing Geometric Surface Imperfections into Sandwich Composite Cylinder Finite Element Method Models

The buckling responses of certain cylindrical shell structures are extremely sensitive to geometric surface imperfections. The NASA Engineering and Safety Center (NESC) Shell Buckling Knockdown Factor Project (SBKF) is conducting research to develop analysis-based buckling design recommendations. Experiments are used to verify the analysis-based factors, but the sensitivity of the test articles to geometric imperfections requires implementing as-manufactured imperfections into high-fidelity finite element method models. Data collection methods such as structured light scanning are used for all geometric surface data used in this work. Common preprocessing and visualization steps used in SBKF are discussed, and steps on how surface scans are prepared for implementation into a finite element model is described. The Python Tool for Implementing Geometric Imperfections in Reduced Structures (Py_TIGIRS), written specifically for the use with SBKF, is briefly described and uses eight functions to extract, modify, and write geometric imperfections into Abaqus input files. Results of the pre-processing methods and results from Py_TIGIRS are provided and compared for Composite Test Article (CTA) 8.2B. Excellent agreement between the visualized scan data and the FEM-extracted geometry is demonstrated. A brief example of why geometric surface imperfections are significant in nonlinear numerical analyses for thin cylinders in axial compression is provided as motivation to use tools such as Py_TIGIRS. Future development of Py_TIGIRS including expansion to structures of arbitrary geometry is planned.

Sandwich structures↗

Compression behavior of delaminated composite plates

The response of delaminated composite plates to compressive in-plane loads was investigated. The delaminated region may be either circular or elliptical, and may be located between any two plies of the laminate. For elliptical delaminations, the axes of the ellipse may be arbitrarily oriented with respect to the applied loads. A model was developed that describes the stresses, strains, and deformation of the sublaminate created by the delamination. The mathematical model is based on a two dimensional nonlinear plate theory that includes the effects of transverse shear deformation. The model takes into account thermal and moisture induced strains, transverse pressures acting on the sublaminate, and contact between the sublaminate and plate. The solution technique used is the Ritz method. A computationally efficient computer implementation of the model was developed. The code can be used to predict the nonlinear-load-strain behavior of the sublaminate including the buckling load, postbuckling behavior, and the onset of delamination growth. The accuracy of the code was evaluated by comparing the model results to benchmark analytical solutions. A series of experiments was conducted on Fiberite T300/976 graphite/epoxy laminates bonded to an aluminum honeycomb core forming a sandwich panel. Either circles or ellipses made from Teflon film were embedded in the laminates, simulating the presence of a delamination. Each specimen was loaded in compression and the strain history of the sublaminate was recorded far into the postbuckling regime. The extent of delamination growth was evaluated by C-scan examination of each specimen. The experimental data were compared to code predictions. The code was found to describe the data with reasonable accuracy. A sensitivity study examined the relative importance of various material properties, the delamination dimensions, the contact model, the transverse pressure differential, the critical strain energy release rate, and the relative growth direction on the buckling load, the postbuckling behavior, and the growth load of the sublaminate.

Peck, Scott O.↗

Out-of-Plane Restraint under Tension In-Plane Loading

The development and description of a test fixture designed to restrict out-of-plane motion in the center region of tension-loaded carbon-epoxy panels are presented herein. The test fixture was used to impose displacement conditions consistent with those in an analytical tool being developed to predict panel behavior in the vicinity of a central notch, which included the assumption that there would be no out-of-plane displacement and no buckling. However, pretest analysis using finite element models for a panel loaded without any out-of-plane restraint in the region of the notch indicated that with an imperfection magnitude equal to 20 percent of the thickness of the thin-skin panel, an unacceptable amount of out-of-plane deformation would occur as Poisson effects induced compression loads in the region of the notch. Therefore, to validate this tool in a test program, a restraint fixture which would suppress out-of-plane motion was required. The panel could not be encased in restraining plates because instrumentation and visibility were required in the vicinity of the notch. Therefore, a fixture that would restrict out-of-plane motion while still allowing access to the surface of the panel at the notch edges for instrumentation and line-of-sight access for cameras was required. To satisfy these requirements, a fixture was designed to restrict only out-of-plane motion near the center of the notch. Two 1.78-m-long test panels were loaded in tension to failure using this fixture. Out-of-plane deformations were not directly measured during testing, so back-to-back strain gages were used to obtain an indication of buckling. Strain results indicated that the restraint fixture performed as designed and buckling did not occur.

Fixtures↗

Out-of-Plane Restraint under Tension In-Plane Loading

The development and description of a test fixture designed to restrict out-of-plane motion in the center region of tension-loaded carbon-epoxy panels are presented herein. The test fixture was used to impose displacement conditions consistent with those in an analytical tool being developed to predict panel behavior in the vicinity of a central notch, which included the assumption that there would be no out-of-plane displacement and no buckling. However, pretest analysis using finite element models for a panel loaded without any out-of-plane restraint in the region of the notch indicated that with an imperfection magnitude equal to 20 percent of the thickness of the thin-skin panel, an unacceptable amount of out-of-plane deformation would occur as Poisson effects induced compression loads in the region of the notch. Therefore, to validate this tool in a test program, a restraint fixture which would suppress out-of-plane motion was required. The panel could not be encased in restraining plates because instrumentation and visibility were required in the vicinity of the notch. Therefore, a fixture that would restrict out-of-plane motion while still allowing access to the surface of the panel at the notch edges for instrumentation and line-of-sight access for cameras was required. To satisfy these requirements, a fixture was designed to restrict only out-of-plane motion near the center of the notch. Two 1.78-m-long test panels were loaded in tension to failure using this fixture. Out-of-plane deformations were not directly measured during testing, so back-to-back strain gages were used to obtain an indication of buckling. Strain results indicated that the restraint fixture performed as designed and buckling did not occur.

Composite structures↗

Design and fabrication of a boron reinforced intertank skirt

Analytical and experimental studies were performed to evaluate the structural efficiency of a boron reinforced shell, where the medium of reinforcement consists of hollow aluminum extrusions infiltrated with boron epoxy. Studies were completed for the design of a one-half scale minimum weight shell using boron reinforced stringers and boron reinforced rings. Parametric and iterative studies were completed for the design of minimum weight stringers, rings, shells without rings and shells with rings. Computer studies were completed for the final evaluation of a minimum weight shell using highly buckled minimum gage skin. The detail design is described of a practical minimum weight test shell which demonstrates a weight savings of 30% as compared to an all aluminum longitudinal stiffened shell. Sub-element tests were conducted on representative segments of the compression surface at maximum stress and also on segments of the load transfer joint. A 10 foot long, 77 inch diameter shell was fabricated from the design and delivered for further testing.

Henshaw, J.↗

Interactive buckling of thin-walled structural components under static and dynamic loads

Recent advances in the study of interactive buckling of thin walled structural components achieved with the aid of finite strip technique used in conjunction with the theory of mode interaction are summarized. The interaction of the primary local mode with Euler buckling (in columns) and flexural torsional buckling (in columns and beams) is of primary interest. The interaction of two companion local modes with the overall mode is also considered briefly for the columns with doubly symmetric cross sections. The effect of dynamic loads in the form of suddenly applied and compression is also investigated.

Sridharan, S.↗

The effect of initial imperfections on shell stability: An updated review

The development of the Delft Interactive Shell Design Code (DISDECO) is described. The purpose is to make the accumulated theoretical, numerical, and practical knowledge of the last years readily accessible to users interested in the analysis of buckling sensitive structures. With this open ended, hierarchical, interactive computer code, the user can access workstation programs of increasing complexity. As a first update of DISDECO, the computational modules of the initial level were modified so as to handle combined loads consisting of axial compression, internal and external pressure, and clockwise or counter clockwise torque. The applied load is assumed to have a uniform spatial distribution and is divided into a fixed and a variable part. The magnitude of the variable part is allowed to vary in proportion to a load parameter Lambda. This leads to an eigenvalue problem for the critical lambda sub C.

Arbocz, J.↗

Improvements to a method for the geometrically nonlinear analysis of compressively loaded stiffened composite panels

The NLPAN computer code uses a finite-strip approach to the analysis of thin-walled prismatic composite structures such as stiffened panels. The code can model in-plane axial loading, transverse pressure loading, and constant through-the-thickness thermal loading, and can account for shape imperfections. The NLPAN code represents an attempt to extend the buckling analysis of the VIPASA computer code into the geometrically nonlinear regime. Buckling mode shapes generated using VIPASA are used in NLPAN as global functions for representing displacements in the nonlinear regime. While the NLPAN analysis is approximate in nature, it is computationally economical in comparison with finite-element analysis, and is thus suitable for use in preliminary design and design optimization. A comprehensive description of the theoretical approach of NLPAN is provided. A discussion of some operational considerations for the NLPAN code is included. NLPAN is applied to several test problems in order to demonstrate new program capabilities, and to assess the accuracy of the code in modeling various types of loading and response. User instructions for the NLPAN computer program are provided, including a detailed description of the input requirements and example input files for two stiffened-panel configurations.

Stoll, Frederick↗

Theoretical Determination of Lifetime of Compressed Plates at Elevated Temperatures

A method for the theoretical determination of the lifetime of com- pressed plates at elevated temperatures is presented. In this approach, linearized equations are used throughout with the assumption that the plate material is a standard linear solid. The critical time (lifetime) is determined by reducing the time-dependent behavior to the time- independent response of purely elastic buckling. Theoretically predicted lifetimes of 2024-T3 (formerly 24S-T3) aluminum-alloy plates at 450 F are compared with experimental values obtained in previous work.

Herrmann, George↗

Stress Evolution Behavior in CoCrPt Alloy Thin Films with varying Pt Concentration

CoCrPt alloy thin film is one of the most promising candidates for ultrahigh density magnetic recording media. One of interesting issues for an application of ferromagnetic thin film to high density magnetic recording media is to investigate growth stress, since stress inevitably generated during thin film fabrication drastically alters magnetic properties as well as mechanical properties due to film fracture and buckling [1]. However, sufficient studies have not been addressed on in situ experimental investigation on stress evolution during film growth of magnetic thin film and its correlation with directly observed film growth structure. We have investigated in situ stress evolution of 400-{angstrom} (Co{sub 82}Cr{sub 18}){sub 100-x}Pt{sub x}/1100-{angstrom} Ti alloy films with varying Pt concentration by means of an ultrahigh vacuum (UHV) chamber equipped with a highly sensitive optical deflection-detecting system [2]. Interestingly enough, the stress evolution patterns during the film deposition are remarkably changed with varying the Pt concentration. CoCrPt alloy films with lower Pt concentration (6 {le} x {le} 13) grow through compressive, tensile, and again compressive stress during film deposition, while CoCrPt alloy films with higher Pt concentration (21 {le} x {le} 28) develop with compressive and relaxed compressive stress without tensile stress generation. In situ stress-evolution behavior for 400-{angstrom} (Co{sub 82}Cr{sub 18}){sub 100-x}Pt{sub x}/1100-{angstrom} Ti alloy films with the Pt concentrations of (a) 6, (b) 13, (c) 21, and (d) 28 at.% are demonstrated in Fig.1. Here, the positive slope corresponds to tensile stress, while the negative slope implies compressive stress. The microstructural studies at the stress transition region reveal that film growth structure plays a major role in considerable change of stress evolution pattern in CoCrPt alloy films with the increase of Pt concentration.

36 MATERIALS SCIENCE↗

Impact damage in small diameter graphite/epoxy composite struts

An investigation was performed to study impact induced damage in small-diameter struts made of a composite material with a brittle matrix system. The major focus is on characterizing the impact behavior associated with the barely visible damage. An experimental procedure including ultrasonic inspection, instrumented impact testing, and delamination buckling and residual strength measurements is presented. From the ultrasonic inspection, it is found that for the strut specimens under investigation, the impact energy level for barely visible damage threshold is above that of the internal damage threshold. A 60- to 65-percent reduction in compressive strength was typical for struts subjected to the barely visible impact damage threshold.

Chen, G.-S.↗