Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLAME”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

2D-imaging of sampling-probe perturbations in laminar premixed flames using Kr X-ray fluorescence

The perturbation of the temperature field caused by a quartz sampling probe has been investigated in a fuel-rich low-pressure premixed ethylene/oxygen/argon/krypton flame using X-ray fluorescence. The experiments were performed at the 7-BM beamline at the Advanced Photon Source (APS) at the Argonne National Laboratory where a continuous beam of X-rays at 15 keV was used to excite krypton atoms that were added to the unburnt flame gases in a concentration of 5% (by volume). The resulting krypton X-ray fluorescence at 12.65 keV was collected and the spatially resolved signal was subsequently converted into the local temperature of the imaged spot. One and two dimensional scans of the temperature field were obtained by translating the entire flame chamber through a pre-programmed sequence of positions on high precision translation stages and measuring the X-ray fluorescence at each location. Multiple measurements were performed at various separations between the burner surface and probe tip, representing sampling positions from the preheat, reaction, and postflame zones of the low-pressure flame. Distortions of up to 1000 K of the burner-probe centerline flame temperature were found with the tip of the probe in the preheat zone and distortions of up to 500 K were observed with it in the reaction and postflame zones. Furthermore, perturbations of the temperature field have been revealed that radially reach as far as 20 mm from the burner-probe centerline and about 3 mm in front of the probe tip. Finally, these results clearly reveal the limitations of one-dimensional models for predicting flame-sampling experiments and comments are made with regard to model developments and validations based on quantitative speciation data from low-pressure flames obtained via intrusive sampling techniques.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

CARS thermometry in laminar sooting ethylene-air co-flow diffusion flames with nitrogen dilution

Temperature measurements were performed in nonpremixed, sooting jet flames using coherent anti-Stokes Raman scattering (CARS). The jet fluid was ethylene diluted with different concentrations of nitrogen, and the co-flow fluid was dry air. The flames were stabilized on a Yale burner, also known as Smooke/Long burner, and the operating conditions were chosen to match previous experiments on the burner by the Yale group and other research groups. The selected flames have also been identified as target flames by the International Sooting Flame Workshop. CARS measurements of temperature provide insight into the structure of these sooting flames and serve as benchmark data for comparison with computations. A dual-pump vibrational CARS system was used here in order to avoid soot interferences. We were able to obtain high quality CARS spectra in all regions of the flame including the highly sooting regions and near the exit of the fuel nozzle, where the nonresonant modulation of the nitrogen CARS spectrum is strong due to the high ethylene concentrations. The measurements are compared with CFD results in literature and discussed in context of measured soot volume fraction, also, from literature.

42 ENGINEERING↗

Front propagation formulation for large eddy simulation of turbulent premixed flames

The front propagation formulation (FPF) for large eddy simulation (LES) of turbulent premixed flames is presented and discussed. The FPF method adopts a regularized Dirac delta function to minimize the spurious propagation of under-resolved filtered flame fronts in LES, while reproducing the reaction characteristics of premixed flame fronts. Here, the extension of the FPF method to LES and the relation to existing sub-filter combustion models are discussed. An algebraic model for the regularized Dirac delta function is presented and validated using direct numerical simulation (DNS) data for statistically planar premixed flames propagating in homogeneous isotropic turbulence. A posteriori validation for a filtered 1-D planar laminar flame is performed to demonstrate the characteristics of FPF in reproducing the propagation speed and the thickness of the under-resolved flame front. LES of a turbulent Bunsen flame is also performed to demonstrate the performance of the proposed method.

42 ENGINEERING↗

Laser diagnostics to characterize the in-flame growth of platinum nanoparticles manufactured by the reactive spray deposition technology

Reactive Spray Deposition Technology (RSDT) is an atmospheric pressure, flame-based advanced manufacturing method used to fabricate Membrane Electrode Assemblies (MEAs) for proton exchange fuel cells and water electrolyzers. RSDT combines the flame synthesis of catalyst nanoparticles and their deposition onto the membrane in one step. The properties of the synthesized nanoparticles, such as their Size Distribution Function (SDF), determine the manufactured electrodes’ performance, which can be evaluated when the deposition is complete via ex-situ characterization of the products. Efforts to improve RSDT for manufacturing state-of-the-art MEAs can be significantly enhanced with integrated laser diagnostics that enable in situ measurement of the synthesized catalyst nanoparticles. This paper reports the implementation of laser diagnostics in an RSDT facility and evaluates their potential to assist the manufacturing process. Laser Light Scattering (LS) and Laser-Induced Incandescence (LII) measurements are performed in the oxygen-rich zone of the flame at various distances from the flame fuel jet nozzle downstream of its luminous region. The measurements quantitatively track the evolution in size and volume fraction of platinum-based nanoparticles in two flames that yield different catalytic properties in the manufactured electrodes. The profiles of the measured nanoparticles’ volume fraction along the flame axis can be estimated a priori so that the average nanoparticle sizes can be measured in quasi-real time via LS. Nanoparticles experience an extremely slow growth rate while being convected at distances from 150 nm to 300 nm from the fuel nozzle. Complementary characterizations of the synthesized nanoparticles are performed ex-situ via High-Angle Annular Darkfield Scanning Transmission Electron Microscopy (HAADF-STEM) image analyses of samples collected on grids at a fixed distance from the fuel jet nozzle. Comparing the results from laser and microscopy techniques not only cross-validates the findings but also provides the parameters to infer the bimodal SDF in-situ and yields evidence that the coagulation efficiency of the synthesized nanoparticles has extremely low values in the investigated zone of the flames.

Rayleigh Light Scattering (LS)↗

Effects of radiation heat loss on planar and spherical hydrofluorocarbon/air flames

Hydrofluorocarbons (HFC), which are mildly flammable and pose potential fire risks, have received greater attention as a viable low global warming potential alternative to traditional refrigerant and fire-suppressant compounds. Therefore, there is a demand to accurately quantify their flammability and re-activity to establish proper safety metrics. Here, this study investigates the effects of radiation heat loss on slowly-propagating HFC/air laminar flames. Planar 1-D simulations of R-32/air and R-1234yf/air flames show significant reductions in laminar flame speed due to radiative heat losses from the flame zone. Simulations of spherically expanding flames (SEF) revealed that the radiation-induced flow needs to be considered when interpreting data from experiments. To this end, a Spherical-flame RADiation-Induced Flow (SRADIF) model was developed to estimate the burned gas inward flow velocities in constant-pressure SEFs, utilizing the optically thin limit assumption to model radiation heat loss. The model was validated against results from detailed numerical simulations of SEFs, from which radiation-induced inward flow was derived using a new formulation considering both the radiation heat loss and convective flow effects. Results show that SRADIF accurately predicts the inward flow velocity for R-32/air mixtures over a range of conditions and performs significantly better compared to existing analytical models. However, the model was unable to accurately predict flow velocities for R-1234yf/air flames and the reason for this is discussed. (224 words)

42 ENGINEERING↗

Laminar flame speed measurements of a gasoline surrogate and its mixtures with ethanol at elevated pressure and temperature

Laminar Flame speed measurements of a gasoline surrogate and mixtures of it with ethanol were conducted using a heated, constant-volume vessel. A spherical propagating flame was observed using a high-speed camera, and laminar flame speed was determined therefrom. Here, the gasoline surrogate, which serves as the baseline for the current study, consisted of four components, namely, iso-octane, n-heptane, toluene, and 1-hexene. Different mixtures of the gasoline surrogate and ethanol were studied, governed by the ethanol percentage in the mixture. That is, E0, E30, E50, and E85 mixtures represent 0%, 30%, 50%, and 85% ethanol in the gasoline surrogate mixture by liquid volume, respectively. Initial temperatures of 335, 359, and 408 K and initial pressures of 1 and 3 bar were investigated. The findings of this study are compared to results in the literature, which show good agreement for E0 but some deviation for the E30 blend. In general, the study showed an increase in laminar flame speed as the ethanol percentage increases in the mixture. Similarly, increasing the initial temperature with fixed ethanol percentage resulted in an increase in laminar flame speed, as expected. In contrast, increasing the initial pressure with fixed Ethanol percentage showed a decrease in laminar flame speed. Finally, the results are compared to an existing chemical kinetics model designed for ethanol and gasoline. Although agreement between the model and data is reasonable and mostly within about 10%, some improvement to the kinetics model is needed to uniformly lower the calculated flame speeds.

09 BIOMASS FUELS↗

Experimental study of vorticity-strain interactions in turbulent premixed counterflow flames

Here, the effects of heat release on interactions between vorticity (ω) and strain rate (s) in turbulent premixed CH 4 /O 2 /N 2 counterflow flames are investigated using simultaneous OH laser-induced fluorescence (LIF) and tomographic particle image velocimetry (TPIV) measurements. A comparison between the flames and a corresponding turbulent non-reacting variable density N 2 -vs-products counterflow reveals the impact of heat release on vorticity-strain rate alignment statistics. Vorticity and strain rate statistics in the flames and non-reacting flow are conditioned on distance from the local flame front and gas mixing layer interface (GMLI) contours, respectively. The magnitude, alignment, and spatial distribution of the vorticity and principal strain rates (s 1 , s 2 , s 3 ) are rather different when heat release is present. Density variations without heat release enhance the ω-s 2 alignment while significantly reducing the ω-s 3 alignment and modestly reducing the ω-s 1 alignment. In contrast, heat release at the flame front further reduces the ω-s 1 alignment but increases the ω-s 3 alignment and suppresses the preferential ω-s 2 alignment. Furthermore, increasing turbulence diminishes the effect of heat release on this preferential alignment. In regions with the largest vorticities, both the reacting and non-reacting counterflows show an increase in the probability of ω-s 2 alignment. All counterflow cases have a net positive vortex-stretching contribution to the enstrophy production with a peak production rate at the flame front or GMLI, but the peak values depend on the density variation, heat release, and turbulence level. Elucidation of the complex interplay between these factors contributes to the understanding of the dynamics of turbulence-flame interactions.

42 ENGINEERING↗

Turbulence/flame/wall interactions in non-premixed inclined slot-jet flames impinging at a wall using direct numerical simulation

In this paper, three-dimensional turbulent non-premixed oblique slot-jet flames impinging at a wall were investigated using direct numerical simulation (DNS). Two cases are considered with the Damköhler number (Da) of case A being twice that of case B. A 17 species and 73-step mechanism for methane combustion was employed in the simulations. It was found that flame extinction in case B is more prominent compared to case A. Reignition in the lower branch of combustion for case A occurs when the scalar dissipation rate relaxes, while no reignition occurs in the lower branch for case B due to excessive scalar dissipation rate. A method was proposed to identify the flame quenching edges of turbulent non-premixed flames in wall-bounded flows based on the intersections of mixture fraction and OH mass fraction iso-surfaces. The flame/wall interactions were examined in terms of the quenching distance and the wall heat flux along the quenching edges. There is essentially no flame/wall interaction in case B due to the extinction caused by excessive turbulent mixing. In contrast, significant interactions between flames and the wall are observed in case A. The quenching distance is found to be negatively correlated with wall heat flux as previously reported in turbulent premixed flames. The influence of chemical reactions and wall on flow topologies was identified. The FS/U and FC/U topologies are found near flame edges, and the NNN/U topology appears when reignition occurs. The vortex-dominant topologies, FC/U and FS/S, play an increasingly important role as the jet turbulence develops.

42 ENGINEERING↗

Simultaneous 10 kHz three-dimensional CH 2 O and tomographic PIV measurements in a lifted partially-premixed jet flame

High-speed, three-dimensional (3D) scalar-velocity field measurements are demonstrated in a lifted partially-premixed dimethyl-ether/air jet flame using simultaneous laser-induced fluorescence (LIF) of formaldehyde (CH 2 O) and tomographic particle image velocimetry (TPIV). The 3D LIF measurements are performed by raster scanning the laser beam from a 100 kHz pulse-burst laser across the probe volume using an acousto-optic deflector. The volumetric reconstruction of the LIF signal from ten parallel planes provides quasi-instantaneous 3D LIF measurements that are synchronized with 10 kHz TPIV measurements. Here, the temporally resolved CH 2 O-LIF and velocity field data are used to analyze Lagrangian particle trajectories and displacement speeds at the base of the lifted flame. The particle trajectories reveal flow structures that are difficult to observe in an Eulerian reference frame. Positive and negative displacement speeds are observed at the CH 2 O-LIF surfaces at the inner and outer regions of the jet flame with a maximum displacement speed of approximately eight times the laminar flame speed of a stoichiometric dimethyl-ether/air mixture. The observations in present study support formation of lean premixed flames near the flame base whose role in flame stabilization should be investigated in more detail.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DNS of ignition and flame stabilization in a simplified gas turbine premixer

With the increasing need for fuel flexibility, mitigation of auto-ignition (AI) inside gas turbine (GT) premixers becomes crucial. They must be designed to yield a sufficiently homogeneous fuel-air mixture to achieve low emissions while at the same time avoiding the occurrence of AI and subsequent flame stabilization. This challenge requires a detailed understanding of turbulent mixing and chemistry interactions. In the present work, a direct numerical simulation (DNS) of an array of jets in crossflow (JICF), representative of an industrial GT premixer, is reported to shed light on these complex phenomena. It is found that AI kernels form in the aft part of the premixer and coalesce into a flame front that then propagates upstream, mainly through the boundary layer, and successively engulfs the jets. This, therefore, suggests a significant role of the jet array pattern on the flame stabilization. It is noted that AI kernels continue to form independently during the whole time of the simulation. To clarify the contribution of AI and diffusion in the ignition kernels and the main flame, chemical explosive mode analysis (CEMA) is employed jointly with a kernel tracking algorithm. It is found that during the initial formation of the flame, many ignition kernels form in mixtures with low scalar dissipation rate and large contribution from AI mode. As they quickly grow, they merge into a single flame front that becomes increasingly more diffusion-assisted over time, balancing the AI mode. Turbulence is shown to have a significant enhancing effect in lean premixed flames, but further analysis is required to fully characterize it. These findings are relevant for the industrial premixer studied, and also for novel micromix concepts that may be used in the next generation of GT combustion systems.

ADVANCED PROPULSION SYSTEMS↗

The importance of fuel dissociation and propargyl + allyl association for the formation of benzene in a fuel-rich 1-hexene flame

Fuel decomposition and benzene formation processes in a premixed, laminar, low-pressure, fuel-rich flame of 1-hexene (C(6)H(12), CH(2)QCH-CH(2)-CH(2)-CH(2)-CH(3)) are investigated by comparing quantitative mole fraction profiles of flame species with kinetic modeling results. The premixed flame, which is stabilized on a flat-flame burner under a reduced pressure of 30 Torr (= 40 mbar), is analyzed by flame-sampling molecular-beam time-of-flight mass spectrometry which uses photoionization by tunable vacuum-ultraviolet synchrotron radiation. The temperature profile of the flame is measured by OH laser-induced fluorescence. The model calculations include the latest rate coefficients for 1-hexene decomposition (J. H. Kiefer et al., J. Phys. Chem. A, 2009, 113, 13570) and for the propargyl (C(3)H(3)) + allyl (a-C(3)H(5)) reaction (J. A. Miller et al., J. Phys. Chem. A, 2010, 114, 4881). The predicted mole fractions as a function of distance from the burner are acceptable and often even in very good agreement with the experimentally observed profiles, thus allowing an assessment of the importance of various fuel decomposition reactions and benzene formation routes. The results clearly indicate that in contrast to the normal reactions of fuel destruction by radical attack, 1-hexene is destroyed mainly by decomposition via unimolecular dissociation forming allyl (a-C(3)H(5)) and n-propyl (n-C(3)H(7)). Minor fuel-consumption pathways include H-abstraction reactions producing various isomeric C(6)H(11) radicals with subsequent beta-scissions into C(2), C(3), and C(4) intermediates. The reaction path analysis also highlights a significant contribution through the propargyl (C(3)H(3)) + allyl (a-C(3)H(5)) reaction to the formation of benzene. In this flame, benzene is dominantly formed through H-assisted isomerization of fulvene, which itself is almost exclusively produced by the C(3)H(3) + a-C(3)H(5) reaction.

10 SYNTHETIC FUELS↗

GRAVITATIONALLY UNSTABLE FLAMES: RAYLEIGH-TAYLOR STRETCHING VERSUS TURBULENT WRINKLING

In this paper, we provide support for the Rayleigh-Taylor-(RT)-based subgrid model used in full-star simulations of deflagrations in Type Ia supernovae explosions. We use the results of a parameter study of two-dimensional direct numerical simulations of an RT unstable model flame to distinguish between the two main types of subgrid models (RT or turbulence dominated) in the flamelet regime. First, we give scalings for the turbulent flame speed, the Reynolds number, the viscous scale, and the size of the burning region as the non-dimensional gravity (G) is varied. The flame speed is well predicted by an RT-based flame speed model. Next, the above scalings are used to calculate the Karlovitz number (Ka) and to discuss appropriate combustion regimes. No transition to thin reaction zones is seen at Ka = 1, although such a transition is expected by turbulence-dominated subgrid models. Finally, we confirm a basic physical premise of the RT subgrid model, namely, that the flame is fractal, and thus self-similar. By modeling the turbulent flame speed, we demonstrate that it is affected more by large-scale RT stretching than by small-scale turbulent wrinkling. In this way, the RT instability controls the flame directly from the large scales. Overall, these results support the RT subgrid model.

79 ASTRONOMY AND ASTROPHYSICS↗

Laser-induced breakdown spectroscopy measurement in methane and biodiesel flames using an ungated detector

Laser-induced breakdown spectroscopy (LIBS) has been applied to measure the equivalence ratio of CH4/air flames using gated detection. In this work, we have developed an ungated, miniature LIBS-based sensor for studying CH4/air and biodiesel flames. We have used this sensor to characterize the biodiesel flame. LIBS spectra of biodiesel flames were recorded with different ethanol concentrations in the biodiesel and also at different axial locations within the flame. The sensor performance was evaluated with a CH4/air flame. LIBS signals of N, O, and H from a CH4/air flame were used to determine the equivalence ratio. A linear relationship between the intensity ratio of H and O lines and the calculated equivalence ratio were obtained with this sensor.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Opposed-Flow Flame Spread in a Narrow Channel Apparatus over Thin PMMA Sheets

Flame spread tests have been conducted over polymethylmethacrylate (PMMA) samples in San Diego State University's Narrow Channel Apparatus (SDSU NCA). The Narrow Channel Apparatus (NCA) has the ability to suppress buoyant flow in horizontally spreading flames, and is currently being investigated as a possible replacement or complement to NASA's current material flammability test standard for non-metallic solids, NASA-STD-(I)-6001B Test 1. The buoyant suppression achieved with a NCA allows for tests to be conducted in a simulated microgravity atmosphere-a characteristic that Test 1 lacks since flames present in Test 1 are buoyantly driven. The SDSU NCA allows for flame spread tests to be conducted with varying opposed flow oxidizer velocities, oxygen percent by volume, and total pressure. Also, since the test sample is placed symmetrically between two confining plates so that there is a gap above and below the sample, this gap can be adjusted. This gap height adjustment allows for a compromise between heat loss from the flame to the confining boundaries and buoyancy suppression achieved by those boundaries. This article explores the effect gap height has on the flame spread rate for 75 μm thick PMMA at 1 atm pressure and 21% oxygen concentration by volume in the SDSU NCA. Flame spread results from the SDSU NCA for thin cellulose fuels have previously been compared to results from tests in actual microgravity at various test conditions with the same sample materials and were found to be in good agreement. This article also presents results from the SDSU NCA for PMMA at 1 atm pressure, opposed oxidizer velocity ranging from 3 to 35 cm/s, oxygen concentration by volume at 21%, 30 %, and 50% and fuel thicknesses of 50 and 75 μm. These results are compared to results obtained in actual microgravity for PMMA obtained at the 4.5s drop tower of MGLAB in Gifu, Japan, and the 5.2s drop tower at NASA's Zero-Gravity Research Facility in Cleveland, OH. This comparison confirms that at 1 atm pressure, the SDSU NCA successfully simulates microgravity for not only thin cellulose fuels, but also for thin PMMA sheets as well. This further supports the idea that the NCA is a viable option to complement or replace NASA's Test 1 for material flammability testing. Tests with thick fuels will be conducted in the future to further characterize the SDSU NCA.

flame spread↗

Effects of Confinement on Flame Spread in Microgravity

Solid fuel combustion experiments aboard the ISS examine the effects of confinement on a concurrent, purely-forced-flow flame spread in microgravity environment. The results for a thin, cotton-fiberglass-blended textile fabric fuel are presented. Flat baffles of differing materials are used to alter the radiative boundary conditions with transparent polycarbonate, black anodized aluminum (reflectance ~ 0), and highly polished aluminum (reflectance ~ 1). The baffles are parallel to the fuel sheet and placed symmetrically on each side. The inter-baffle distance is varied to change the boundary conditions for the flow. In all tests, samples are ignited at the upstream leading edge and allowed to burn to completion. Results show that the flame reaches a steady length and spread rate at low flow speeds (< 15 cm/s) for all tested inter-baffle distances. As the distance decreases, the flame length and spread rate first increase then decrease showing an optimal inter-baffle distance. For all baffle types, the flame either fails to ignite or extinguishes before reaching the end of the sample when the inter-baffle distance is too small (~ 1 cm). This is attributed to the reduction of oxygen supply to the flame zone and heat loss to the baffles. The results also show at the same inter-baffle distance, flame length and spread rate are highest for polished aluminum baffles, and lowest for transparent polycarbonate baffles. The differences are most prominent at intermediate tested baffle distances. While the radiative heat feedback from the baffles is expected to increase when the baffle distance decreases, the combustion is limited by the reduced oxygen supply. Near this limit, flame lengths and spread rates are similar for all baffle types.

Microgravity↗

Effect of NO on extinction and re-ignition of vortex-perturbed hydrogen flames.

The catalytic effect of nitric oxide (NO) on the dynamics of extinction and re-ignition of a vortex-perturbed non-premixed hydrogen-air flame is studied in a counterflow burner. A diffusion flame is established with counterflowing streams of nitrogen-diluted hydrogen at ambient temperature and air heated to a range of temperatures that brackets the auto-ignition temperature. Localized extinction is induced by impulsively driving a fuel-side toroidal vortex into the steady flame, and the recovery of the extinguished region is monitored by planar laser-induced fluorescence (PLIF) of the hydroxyl radical (OH). The dynamics of flame recovery depend on the air temperature and fuel concentration, and four different recovery modes are identified. These modes involve combinations of edge-flame propagation and the expansion of an auto-ignition kernel that forms within the extinguished region. The addition of a small amount of NO significantly alters the re-ignition process by shifting the balance between chain-termination and chain-propagation reactions to enhance auto-ignition. The ignition enhancement by this catalytic effect causes a shift in the conditions that govern the recovery modes. In addition, the effects of NO concentration and vortex strength on the flame recovery are examined. Direct numerical simulations of the flame-vortex interaction with and without NO doping show how the small amount of OH produced by NO-catalyzed reactions has a significant impact on the development of an auto-ignition kernel. This joint experimental and numerical study provides detailed insight into the interaction between transient flows and ignition processes.

08 HYDROGEN↗

A 2-D DNS investigation of extinction and reignition dynamics in nonpremixed flame-vortex interactions

Two-dimensional (2-D) DNS investigations of extinction and reignition dynamics during interactions of laminar nonpremixed flames with counterrotating vortex pairs are performed. The length and velocity scales chosen for the vortices are representative of those in the near fields of high-Reynolds-number jets such as those occurring in Diesel engines. The governing equations are solved with sixth-order spatial discretization and fourth-order time integration. Chemistry is modeled as an irreversible single-step reaction. Local extinction along the symmetry axis, followed by reignition, is observed. The extinction is characterized by strong unsteady effects, which are captured well by 1-D transient diffusion flamelet libraries, provided the time-history of the instantaneous scalar dissipation rate is taken into account. On the other hand, reignition is essentially a 2-D phenomenon involving flame-flame interactions, which are favored for smaller vortices and increasing flame curvature. The effects of unsteadiness and curvature on extinction and reignition are carefully assessed through parametric studies involving a range of vortex and flame characteristics. The interaction outcomes are summarized on Reynolds-Damkoehler number (Re-Da) diagrams, which show the combined effects of unsteadiness and curvature on extinction and reignition. The implications of the observed interaction outcomes for turbulent combustion modeling in the near fields of jet diffusion flames are discussed. (author)

33 ADVANCED PROPULSION SYSTEMS↗

Dynamics of premixed hydrogen/air flames in mesoscale channels

Direct numerical simulation with detailed chemistry and transport is used to study the stabilization and dynamics of lean ({phi}=0.5) premixed hydrogen/air atmospheric pressure flames in mesoscale planar channels. Channel heights of h=2, 4, and 7 mm, and inflow velocities in the range 0.3{<=}U{sub IN}{<=}1100cm/ s are investigated. Six different burning modes are identified: mild combustion, ignition/extinction, closed steady symmetric flames, open steady symmetric flames, oscillating and, finally, asymmetric flames. Chaotic behavior of cellular flame structures is observed for certain values of U{sub IN}. Stability maps delineating the regions of the different flame types are finally constructed. (author)

08 HYDROGEN↗