Search NASA⌕ Search

SEARCH · Search NASA

Results for “Flight data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Solar and Heliospheric Observatory (SOHO) Flight Dynamics Simulations Using MATLAB (R)

This paper describes a study to verify onboard attitude control laws in the coarse Sun-pointing (CSP) mode by simulation and to develop procedures for operational support for the Solar and Heliospheric Observatory (SOHO) mission. SOHO was launched on December 2, 1995, and the predictions of the simulation were verified with the flight data. This study used a commercial off the shelf product MATLAB(tm) to do the following: Develop procedures for computing the parasitic torques for orbital maneuvers; Simulate onboard attitude control of roll, pitch, and yaw during orbital maneuvers; Develop procedures for predicting firing time for both on- and off-modulated thrusters during orbital maneuvers; Investigate the use of feed forward or pre-bias torques to reduce the attitude handoff during orbit maneuvers - in particular, determine how to use the flight data to improve the feed forward torque estimates for use on future maneuvers. The study verified the stability of the attitude control during orbital maneuvers and the proposed use of feed forward torques to compensate for the attitude handoff. Comparison of the simulations with flight data showed: Parasitic torques provided a good estimate of the on- and off-modulation for attitude control; The feed forward torque compensation scheme worked well to reduce attitude handoff during the orbital maneuvers. The work has been extended to prototype calibration of thrusters from observed firing time and observed reaction wheel speed changes.

Headrick, R. D.↗
NASA NTRS1995

SeaWiFS technical report series. Volume 31: Stray light in the SeaWiFS radiometer

Some of the measurements from the Sea-viewing Wide Field-of-view Sensor (SeaWiFS) will not be useful as ocean measurements. For the ocean data set, there are procedures in place to mask the SeaWiFS measurements of clouds and ice. Land measurements will also be masked using a geographic technique based on each measurment's latitude and longitude. Each of these masks involves a source of light much brighter than the ocean. Because of stray light in the SeaWiFS radiometer, light from these bright sources can contaminate ocean measurements located a variable number of pixels away from a bright source. In this document, the sources of stray light in the sensor are examined, and a method is developed for masking measurements near bright targets for stray light effects. In addition, a procedure is proposed for reducing the effects of stray light in the flight data from SeaWiFS. This correction can also reduce the number of pixels masked for stray light. Without these corrections, local area scenes must be masked 10 pixels before and after bright targets in the along-scan direction. The addition of these corrections reduces the along-scan masks to four pixels before and after bright sources. In the along-track direction, the flight data are not corrected, and are masked two pixels before and after. Laboratory measurements have shown that stray light within the instrument changes in a direct ratio to the intensity of the bright source. The measurements have also shown that none of the bands show peculiarities in their stray light response. In other words, the instrument's response is uniform from band to band. The along-scan correction is based on each band's response to a 1 pixel wide bright sources. Since these results are based solely on preflight laboratory measurements, their successful implementation requires compliance with two additional criteria. First, since SeaWiFS has a large data volume, the correction and masking procedures must be such that they can be converted into computationally fast algorithms. Second, they must be shown to operate properly on flight data. The laboratory results, and the corrections and masking procedures that derive from them, should be considered as zeroeth order estimates of the effects that will be found on orbit.

Hooker, Stanford B.↗
NASA NTRS2009

A Perspective on Development Flight Instrumentation and Flight Test Analysis Plans for Ares I-X

NASA. s Constellation Program will take a significant step toward completion of the Ares I crew launch vehicle with the flight test of Ares I-X and completion of the Ares I-X post-flight evaluation. The Ares I-X flight test vehicle is an ascent development flight test that will acquire flight data early enough to impact the design and development of the Ares I. As the primary customer for flight data from the Ares I-X mission, Ares I has been the major driver in the definition of the Development Flight Instrumentation (DFI). This paper focuses on the DFI development process and the plans for post-flight evaluation of the resulting data to impact the Ares I design. Efforts for determining the DFI for Ares I-X began in the fall of 2005, and significant effort to refine and implement the Ares I-X DFI has been expended since that time. This paper will present a perspective in the development and implementation of the DFI. Emphasis will be placed on the process by which the list was established and changes were made to that list due to imposed constraints. The paper will also discuss the plans for the analysis of the DFI data following the flight and a summary of flight evaluation tasks to be performed in support of tools and models validation for design and development.

Huebner, Lawrence D.↗
NASA NTRS1970

Post Flight Dynamic Analysis Simulation

Digital six-degrees-of-freedom, open loop Saturn 5 first stage flight evaluation simulation program obtains post flight simulation of the launch vehicle using actual flight data as input. Results are compared with measured data. For preflight analysis, the program uses predicted flight data as input.

Gregory, B. R.↗
NASA NTRS1989

Numerical aerodynamic simulation of the space shuttle ascent environment

After the STS 51-L accident, an extensive review of the Space Shuttle Orbiter's ascent aerodynamic loads uncovered several questionable areas that required further analysis. The insight gained by comparing the Shuttle ascent CFD numerical simulations, obtained by the NASA Ames Space Shuttle Flow Simulation Group, to the current IVBC-3 aerodynamic loads database was instrumental in resolving uncertainties on the Orbiter payload bay doors and fuselage. Initial confidence in the numerical simulations was gained by comparing them with the limited flight data that had been obtained during the Orbiter Flight Test (OFT) program. Current CFD results exist for Mach numbers 0.6, 0.9, 1.05, 1.55, 2.0, and 2.5. Since the pre STS-1 wind tunnel test program (IA-105) often yields considerable differences when compared to STS-5 flight data, the M(sub infinity) = 1.05 transonic case is the most investigated. The IA308 mated-vehicle hot gas plume wind tunnel test, recently completed at AEDC 16T (transonic) and Lewis (hypersonic), is also used to compare with the computation where applicable.

Slotnick, Jeff P.↗
NASA NTRS1992

Project Ares 3

The mission of Project Ares is to design and fabricate an Earth prototype, autonomous flying rover capable of flying on the Martian surface. The project was awarded to California State University, Northridge (CSUN) in 1989 where an in-depth paper study was completed. The second year's group, Project Ares 2, designed and fabricated a full-scale flight demonstration aircraft. Project Ares 3, the third and final group, is responsible for propulsion system design and installation, controls and instrumentation, and high altitude testing. The propulsion system consists of a motor and its power supply, geartrain, and propeller. The motor is a four-brush DC motor powered by a 50-V NiCd battery supply. A pulley and belt arrangement is used for the geartrain and includes light weight, low temperature materials. The propeller is constructed from composite materials which ensures high strength and light weight, and is specifically developed to provide thrust at extremely high altitudes. The aircraft is controlled with a ground-based radio control system and an autopilot which will activate in the event that the control signal is lost. A transponder is used to maintain radar contact for ground tracking purposes. The aircraft possesses a small, onboard computer for collecting and storing flight data. To safeguard the possibility of computer failure, all flight data is transmitted to a ground station via a telemetry system. An initial, unpowered, low-level test flight was completed in August of 1991. Testing of systems integration in the second low-level test flight resulted in loss of elevator control which caused considerable damage on landing. Complete failure analysis and repairs are scheduled for September of 1992.

Raymer, Dan↗
NASA NTRS1995

Estimation of attitude sensor timetag biases

This paper presents an extended Kalman filter for estimating attitude sensor timing errors. Spacecraft attitude is determined by finding the mean rotation from a set of reference vectors in inertial space to the corresponding observed vectors in the body frame. Any timing errors in the observations can lead to attitude errors if either the spacecraft is rotating or the reference vectors themselves vary with time. The state vector here consists of the attitude quaternion, timetag biases, and, optionally, gyro drift rate biases. The filter models the timetags as random walk processes: their expectation values propagate as constants and white noise contributes to their covariance. Thus, this filter is applicable to cases where the true timing errors are constant or slowly varying. The observability of the state vector is studied first through an examination of the algebraic observability condition and then through several examples with simulated star tracker timing errors. The examples use both simulated and actual flight data from the Extreme Ultraviolet Explorer (EUVE). The flight data come from times when EUVE had a constant rotation rate, while the simulated data feature large angle attitude maneuvers. The tests include cases with timetag errors on one or two sensors, both constant and time-varying, and with and without gyro bias errors. Due to EUVE's sensor geometry, the observability of the state vector is severely limited when the spacecraft rotation rate is constant. In the absence of attitude maneuvers, the state elements are highly correlated, and the state estimate is unreliable. The estimates are particularly sensitive to filter mistuning in this case. The EUVE geometry, though, is a degenerate case having coplanar sensors and rotation vector. Observability is much improved and the filter performs well when the rate is either varying or noncoplanar with the sensors, as during a slew. Even with bad geometry and constant rates, if gyro biases are independently known, the timetag error for a single sensor can be accurately estimated as long as its boresight is not too close to the spacecraft rotation axis.

Sedlak, J.↗
NASA NTRS2022

MSL MMRTG Power Modeling for Lifetime Performance Predictions

The Multi-Mission Radioisotope Thermoelectric Generator (MMRTG) has been providing power to the Mars Science Laboratory (MSL) rover, Curiosity, for surface operations since 2012. The Jet Propulsion Laboratory (JPL) has employed the Life Performance Prediction Model (LPPM) to generate predictions and outputs based upon flight data from the rover and experimental data from the thermoelectric (TE) couples. In order to make these predictions, LPPM requires various spacecraft inputs relevant to RTG performance such as fin root temperature, load voltage, general purpose heat source (GPHS) inventory, etc., combined with couple data such as thermoelectric properties, interface degradation, and sublimation properties. With tens of thousands of hours of flight data to date, LPPM can not only track performance to date, but also make predictions on the power output of the MMRTG through the 17-year end-of-design-life (EODL). These predictions are useful for mission planners and surface operators who rely on the MMRTG for power in order to perform the critical science necessary during the mission. This paper will showcase the power data extracted from the flight electronics, comparing it to the predictions and outputs generated from LPPM.

Pinkowski, Stanley↗
NASA NTRSDate not supplied

Learjet Test Update

An update on the Learjet acoustic flight test was presented. The intent of the effort was to acquire flight data for the development of flight corrections to scale-model data. The flights were completed on September 8, 2022. Weather measurements were acquired with a combination of an instrumented drone and a ground based LiDAR system. Acquisition of comparative scale-model data will be completed on October 7, 2022.

jet noise↗
NASA NTRS2022

Comparison of Likelihood Methods for Generalized Linear Mixed Models with Application to Quiet Supersonic Flights 2018 Data

Repeated measurement will be a feature of the survey data collected during the Quesst missionX-59 community response tests (CRT). Since each participant will report his or her categorical level of annoyance in response to multiple events, the responses from any single individual may be correlated with one another. Several models within the class of generalized linear mixed models (GLMM) are pertinent to the analysis of correlated categorical outcomes; the random intercept logistic regression model is one example. Both Bayesian and frequentist methods for fitting these models are available, with frequentist methods relying on some form of approximation (of either an integral or the integrand) that appears in the marginal likelihood function. Given several anticipated similarities of the X-59 CRT data to data collected during a past risk reduction, Quiet Supersonic Flights 2018 (QSF18), this short note is intended to create awareness. It documents an instance in which a reported population average dose-response relationship derived from QSF18 single event data was distorted by the integral approximation applied in likelihood-based methods. We review some of the available literature on the topic, compare the outputs of several different computational approaches implemented in available statistical software, and present simple corrective actions that may be useful during the Quesst mission.

dose-response model↗
NASA NTRS1979

Integrated energy management study. Energy efficient transport program

The Integrated Energy Management (IEM) Study investigated the practicality and feasibility of a closed-loop energy management system for transport aircraft. The study involved: (1) instrumentation and collection of in-flight data for a United Airlines 727-200 flying 80 revenue flights throughout the United Airlines network,(2) analysis of the in-flight data to select representative city pairs and establish operational procedures employed in flying a reference flight profile, (3) simulation of the reference profile in a fast-time model to verify the model and establish performance values against which to measure IEM benefits, (4) development of IEM algorithms, and (5) assessment of the IEM concept.

Source record↗
NASA NTRS1997

Drag Prediction and Transition in Hypersonic Flow

This paper discusses progress on issues such as instability studies, nose-bluntness and angle-of-attack effects, and leading-edge-contamination problems from theoretical, computational, and experimental points of view. Also included is a review of wind-tunnel and flight data, including high-Re flight transition data, the levels of noise in flight and in wind tunnels, and how noise levels can affect parametric trends. A review of work done on drag accounting and the role of viscous drag for hypersonic vehicles is also provided.

Reed, Helen L.↗
NASA NTRS2018

Creating a Voyager Thermal Model 39 Years Into the Flight Mission, Along with Model Correlation and Application

After 39 years of continuous operation in space, the output of the Voyager 1 & 2 spacecraft RTG power systems has decreased to the point where managing the power margin and maintaining thermal control has become increasingly difficult. As the total power dissipation in the bus has decreased, propellant line temperatures and margin above minimum AFTs have decreased, creating risk of the hydrazine freezing (at 1.6°C). This is further complicated by the lack of existing thermal models that can be used to assess propellant tank and line temperatures. In 2014, an effort was begun to create a Voyager spacecraft thermal model for that purpose.A steady-state Thermal Desktop model has been created from scratch over the past two years. The initial thermal model development was started by Applied Sciences Laboratory (ASL) under contract to JPL. The effort relied primarily on archived manufacturing drawings, limited documentation, interviews of senior engineers who worked on the Voyager design and implementation, and the experience of the Voyager Flight Operations team.Data from the Voyager System Thermal Vacuum tests is no longer available, making it necessary to correlate the model to more recent flight data and small in-flight tests. Correlation was achieved to within ±5°C for a hot case and a cold case (both data sets from 2014). However, the flight system has very few temperature sensors directly on propellant lines. So the task remains to determine how best to use the model, in conjunction with flight data, to make sure the Voyagers can continue to fly successfully. How does one go about creating a thermal model for a spacecraft that is already launched, has limited existing mechanical description files, no thermal model in order to do a maneuver that was never planned when the spacecraft was designed?

Ledeboer, William C.↗
NASA NTRS2021

Medium-Sized Helicopter Noise Abatement Flight Test Data Report

Helicopter noise has consistently hindered operations within urban areas and surrounding communities. To combat this, an extensive flight test campaign, described herein, was conducted to gather acoustic data to support helicopter noise research (e.g., physics-based modeling, operational planning, etc.). Acoustic measurements were collected from four helicopters in the medium-sized weight class with maximum takeoff gross weights between 7,400 and 14,200 lb: a Bell 205 “Huey”, a Sikorsky S-76D, a Leonardo AW139, and a US Coast Guard MH-65 Dolphin (a variant of the commercial Airbus AS365 Dauphin). Each aircraft per- formed a subset of level flyovers, steady descents, turns with various initial conditions, and noise abatement approaches. A distributed ground microphone array spanning approximately 2,000 by 4,000 ft collected measurements of each flyover event. Additionally, a dedicated semicircular microphone array was used for gathering acoustic measurements of static conditions (e.g., hover). This report provides an overview of the flight test methodology, conditions tested, equipment used, and details of the accompanying distribution dataset. Figures of sample results generated for each test point are included to enable comparison and selection of the data at the discretion of the user. Specifically, source noise hemispheres of the steady flight conditions illustrate directivity of over- all levels. Noise contours over the array provide insight into the ground levels associated with approaches and turning events. These data figures are derived from the original acoustic pressure-time histories and vehicle tracking data that are provided in the distribution dataset.

Rotorcraft↗
NASA NTRS1979

Optimization and simulation of flight control laws under parameter uncertainty and external disturbances

Several tasks pertinent to flight control in parameter uncertainty and wind-gust loading were successfully completed. Identification algorithms for extracting stability and control derivatives from flight data taking gust loading into account were developed. They were verified by simulation and evaluated throughly on actual flight data taken on a Lockheed Jet Star flying in turbulence. In particular the need for automatically generated dither-like inputs was studied. Criteria for performance evaluation using stochastic models were developed for gust alleviation as well as handling quantities. Algorithms for assessing degradation in performance due to parameter uncertainty were developed and evaluated using flight test data.

Source record↗
NASA NTRS2020

Recent NASA Wind Tunnel Free-Flight Testing of a Multirotor Unmanned Aircraft System Vehicle

Wind tunnel free-flight tests of a small quadrotor vehicle were completed in the NASA Langley 12-Foot Low Speed Tunnel and 20-Foot Vertical Spin Tunnel. The primary objective of these tests was to acquire flight data in forward and descending flight for the purpose of assessing the fidelity of an all-attitude flight dynamics simulation previously developed from static and dynamic wind tunnel data. A secondary objective was to demonstrate and mature free-flight test methods specific to the emerging class of small unmanned aircraft and urban air mobility vehicles. Experimental flight data correlated well with simulation predictions which included steady trim conditions consistent with straight and level flight and quasi-steady conditions associated with descent velocities prone to vortex ring state development. The test method was shown to be well suited to these classes of vehicles and several unique infrastructure requirements, including tether systems and data acquisition requirements were identified. In addition, unique operational test techniques and safety procedures were developed to accommodate the testing. Results of these tests will be used to support air traffic management studies and research into safety assurance concepts that enable the integration of these classes of vehicles into the National Airspace System.

John V Foster↗
NASA NTRS2010

Ares I-X Range Safety Simulation Verification and Analysis IV and V

NASA s ARES I-X vehicle launched on a suborbital test flight from the Eastern Range in Florida on October 28, 2009. NASA generated a Range Safety (RS) flight data package to meet the RS trajectory data requirements defined in the Air Force Space Command Manual 91-710. Some products included in the flight data package were a nominal ascent trajectory, ascent flight envelope trajectories, and malfunction turn trajectories. These data are used by the Air Force s 45th Space Wing (45SW) to ensure Eastern Range public safety and to make flight termination decisions on launch day. Due to the criticality of the RS data in regards to public safety and mission success, an independent validation and verification (IV&V) effort was undertaken to accompany the data generation analyses to ensure utmost data quality and correct adherence to requirements. Multiple NASA centers and contractor organizations were assigned specific products to IV&V. The data generation and IV&V work was coordinated through the Launch Constellation Range Safety Panel s Trajectory Working Group, which included members from the prime and IV&V organizations as well as the 45SW. As a result of the IV&V efforts, the RS product package was delivered with confidence that two independent organizations using separate simulation software generated data to meet the range requirements and yielded similar results. This document captures ARES I-X RS product IV&V analysis, including the methodology used to verify inputs, simulation, and output data for an RS product. Additionally a discussion of lessons learned is presented to capture advantages and disadvantages to the IV&V processes used.

Tarpley, Ashley↗