SEARCH · Search NASA

Results for “PRESSURE DISTRIBUTION - AIRFOILS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Experimental investigation of a jet inclined to a subsonic crossflow

Experimental investigations have been conducted to determine the surface-pressure distribution on a flat plate and a body of revolution with a jet issuing at a large angle to the free stream and to obtain a better understanding of the entrainment mechanism close to the jet exit by quantitative mean velocity surveys. Pressure data were obtained with a flat plate model at several nozzle injection angles using a single round nozzle. For the body of revolution model, data were obtained with a round jet exhausting perpendicular to the crossflow and with two round jets spaced two to six nozzle diameters apart. Mean velocity measurements were obtained with laser velocimeter surveys near the base of a round jet exhausting normal to a flat plate. For the flat plate model, the pressure field shifts downstream and the entrainment effect decreases with decreasing nozzle injection angle. For the body of revolution model with two jets, the jet-induced effect of the rear jet on the surface-pressure distribution was less than the front jet. The flow regions close to the jet are defined by the laser surveys, but further mean velocity surveys are required to understand the entrainment mechanism.

Aoyagi, K.↗

NASA NTRS1993

Generic hypersonic vehicle performance model

An integrated computational model of a generic hypersonic vehicle was developed for the purpose of determining the vehicle's performance characteristics, which include the lift, drag, thrust, and moment acting on the vehicle at specified altitude, flight condition, and vehicular configuration. The lift, drag, thrust, and moment are developed for the body fixed coordinate system. These forces and moments arise from both aerodynamic and propulsive sources. SCRAMjet engine performance characteristics, such as fuel flow rate, can also be determined. The vehicle is assumed to be a lifting body with a single aerodynamic control surface. The body shape and control surface location are arbitrary and must be defined. The aerodynamics are calculated using either 2-dimensional Newtonian or modified Newtonian theory and approximate high-Mach-number Prandtl-Meyer expansion theory. Skin-friction drag was also accounted for. The skin-friction drag coefficient is a function of the freestream Mach number. The data for the skin-friction drag coefficient values were taken from NASA Technical Memorandum 102610. The modeling of the vehicle's SCRAMjet engine is based on quasi 1-dimensional gas dynamics for the engine diffuser, nozzle, and the combustor with heat addition. The engine has three variable inputs for control: the engine inlet diffuser area ratio, the total temperature rise through the combustor due to combustion of the fuel, and the engine internal expansion nozzle area ratio. The pressure distribution over the vehicle's lower aft body surface, which acts as an external nozzle, is calculated using a combination of quasi 1-dimensional gas dynamic theory and Newtonian or modified Newtonian theory. The exhaust plume shape is determined by matching the pressure inside the plume, calculated from the gas dynamic equations, with the freestream pressure, calculated from Newtonian or Modified Newtonian theory. In this manner, the pressure distribution along the vehicle after body expansion surface is then determined. The aerodynamic modeling, the engine modeling, and the exhaust plume analysis are described in more detail. A description of the computer code used to perform the above calculations is given and an input/output example is then given. The computer code is available on a Macintosh floppy disk.

Chavez, Frank R.↗

NASA NTRS1988

Thermal and pressure diffusion effects in high altitude flows

An apparently anomalous change in composition adjacent to a non-catalytic surface in an earlier DSMC calculation of a non-reacting gas mixture is shown to have been due to thermal diffusion. Both thermal and pressure diffusion can lead to species separation effects in the flow of gas mixtures, but are not generally included in Navier-Stokes formulations. Additional DSMC calculations are made for blunt-body and plume expansion flows using both a simple gas and an otherwise identical gas mixture. These test calculations indicate that the pressure distribution on the forward face of a blunt body is largely unaffected by the species separation in the stagnation region. The gas density in this region is significantly affected and there is a slight change in the heat transfer to the surface. The pressure distribution around the shoulder of the body is affected. Very large separations occur in the plume expansion of the gas mixtures and there is an order of magnitude increase in density in the backflow region for the mixture.

Bird, G. A.↗

NASA NTRS1993

Users manual for the NASA Lewis three-dimensional ice accretion code (LEWICE 3D)

A description of the methodology, the algorithms, and the input and output data along with an example case for the NASA Lewis 3D ice accretion code (LEWICE3D) has been produced. The manual has been designed to help the user understand the capabilities, the methodologies, and the use of the code. The LEWICE3D code is a conglomeration of several codes for the purpose of calculating ice shapes on three-dimensional external surfaces. A three-dimensional external flow panel code is incorporated which has the capability of calculating flow about arbitrary 3D lifting and nonlifting bodies with external flow. A fourth order Runge-Kutta integration scheme is used to calculate arbitrary streamlines. An Adams type predictor-corrector trajectory integration scheme has been included to calculate arbitrary trajectories. Schemes for calculating tangent trajectories, collection efficiencies, and concentration factors for arbitrary regions of interest for single droplets or droplet distributions have been incorporated. A LEWICE 2D based heat transfer algorithm can be used to calculate ice accretions along surface streamlines. A geometry modification scheme is incorporated which calculates the new geometry based on the ice accretions generated at each section of interest. The three-dimensional ice accretion calculation is based on the LEWICE 2D calculation. Both codes calculate the flow, pressure distribution, and collection efficiency distribution along surface streamlines. For both codes the heat transfer calculation is divided into two regions, one above the stagnation point and one below the stagnation point, and solved for each region assuming a flat plate with pressure distribution. Water is assumed to follow the surface streamlines, hence starting at the stagnation zone any water that is not frozen out at a control volume is assumed to run back into the next control volume. After the amount of frozen water at each control volume has been calculated the geometry is modified by adding the ice at each control volume in the surface normal direction.

Bidwell, Colin S.↗

NASA NTRS1984

An evaluation of a parabolized Navier-Stokes (PNS) code for cone-cylinder-flared configurations

A PNS code's capability to predict the onset of laminar and turbulent boundary layer separation, forces, moments, and pressure distributions was investigated. Predictions of incipient separation show good agreement with experimental results. Force and moment calculations were found to agree favorably with experimental data for a wide range of geometries for Mach numbers from 2 to 4 with turbulent boundary layers. Limited comparison of pressure distribution data also showed good agreement. Skin friction and Stanton number calculations are presented to indicate the code's capability to calculate this information and hence, provide a complete data base for attached flow conditions. The sensitivity of these calculations to smoothing and marching parameter variations was examined and found to be acceptable for most design work. The code was found to be suitable to complement or reduce wind tunnel experimentation for the design of this class of configuration with regard to accuracy, cost and usability.

Cottrell, C. J.↗

NASA NTRS1986

Measurement and prediction of flow through a replica segment of a mildly atherosclerotic coronary artery of man

Pressure distributions were measured along a hollow vascular axisymmetric replica of a segment of the left circumflex coronary artery of man with mildly atherosclerotic diffuse disease. A large range of physiological Reynolds numbers from about 60 to 500, including hyperemic response, was spanned in the flows investigation using a fluid simulating blood kinematic viscosity. Predicted pressure distributions from the numerical solution of the Navier-Stokes equations were similar in trend and magnitude to the measurements. Large variations in the predicted velocity profiles occurred along the lumen. The influence of the smaller scale multiple flow obstacles along the wall (lesion variations) led to sharp spikes in the predicted wall shear stresses. Reynolds number similarity was discussed, and estimates of what time averaged in vivo pressure drop and shear stress might be were given for a vessel segment.

Back, L. H.↗

NASA NTRSDate not supplied

A Data-Driven Reduced Order Model of an Isolated Rotor

There are numerous conceptual design stage rotorcraft analysis tasks which demand a high-fidelity and low cost method for rotor load distribution predictions. Considering Urban Air Mobility (UAM) vehicles aim to operate in close proximity to buildings and with unique rotor configurations, there is a significant challenge in quickly and accurately modeling rotors operating in complex, turbulent flow fields. One potential path for deriving a high-fidelity, low cost rotor model is with data-driven surrogate modeling. In this study, an initial investigation is taken to apply a proper orthogonal decomposition (POD) based reduced order model (ROM) for the purpose of pressure distribution prediction. In this study, a POD ROM was derived to produce distributed pressure predictions on rotor blades subjected to topology change due to variation in twist and taper ratio. Rotor twist was varied between 0◦, 10◦, 20◦, and 30◦ while taper ratio was varied between 1.0, 0.9, 0.8, and 0.7. All rotors consisted of a single blade. The POD ROM was validated for three demonstration cases; a high thrust rotor in hover, a low thrust rotor in hover, and a rotor in forward flight with a flight speed of M = 0.1. Results showed highly accurate distributed load predictions could be achieved at minimal computational cost. Computational cost for hovering blade surface pressure modeling was reduced from 12 hours on 440 cores to 10−5 seconds on a single core. For blade in forward flight cost was reduced from 20 hours on 440 cores to 0.6 seconds on a single core. For cases of high thrust and low thrust rotors, POD ROM was used to undergo a design optimization of the rotor such that figure of merit was maximized. Total optimization time for each case was 1 minute.

Data-Driven↗

NASA NTRS1978

Theoretical study of hull-rotor aerodynamic interference on semibuoyant vehicles

Analytical methods are developed to predict the pressure distribution and overall loads on the hulls of airships which have close coupled, relatively large and/or high disk loading propulsors for attitude control, station keeping, and partial support of total weight as well as provision of thrust in cruise. The methods comprise a surface-singularity, potential-flow model for the hull and lifting surfaces (such as tails) and a rotor model which calculates the velocity induced by the rotor and its wake at points adjacent to the wake. Use of these two models provides an inviscid pressure distribution on the hull with rotor interference. A boundary layer separation prediction method is used to locate separation on the hull, and a wake pressure is imposed on the separated region for purposes of calculating hull loads. Results of calculations are shown to illustrate various cases of rotor-hull interference and comparisons with small scale data are made to evaluate the method.

Spangler, S. B.↗

NASA NTRS1981

Steady and nonsteady supersonic turbulent afterbody flow

The effect of the specific heat ratio gamma of the incoming ideal gas on the flow properties, especially on pressure distributions along the base and sting surfaces and on reattachment distance, was investigated. The specific heat ratios considered were gamma = 1.2, 1.4, and 1.667. Also, effects of other major parameters, such as eddy-viscosity coefficient (or effective Reynolds number) and Mach number, on the afterbody pressure and reattachment distance were studied and are discussed. Evolution of shock induced flow and stabilization time were examined and are discussed for a transient problem. The important influence of the flow-field geometry, pressure distributions, and reattachment distance on the aerodynamics radiative heat transfer for an atmosphere entry probe in high speed flight are briefly described.

Yoshikawa, K. K.↗

NASA NTRS1974

Use of potential flow theory to evaluate subsonic inlet data from a simulator-powered nacelle at cruise conditions

Incompressible potential flow theory corrected for compressibility effects, using the Lieblein-Stockman compressibility correction, was used to predict surface and flow field static pressures for a subsonic inlet at cruise conditions. The calculated internal and external surface static pressures were in good agreement with data at most conditions. The analysis was used to determine the capture stream-tube location and static-pressure distribution. Additive drag coefficients obtained from these results were consistently higher than those obtained using one-dimensional compressible flow theory. Increasing the distance between the inlet and boattail increased the cowl drag force. The effect of the boundary layer on internal and external surface static-pressure distributions was small at the design cruise condition. The analytical results may be used as an aid to data reduction and for predicting inlet mass flow, stagnation point location, and inlet additive drag.

Bober, L. J.↗

NASA NTRS1991

A system-approach to the elastohydrodynamic lubrication point-contact problem

The classical EHL (elastohydrodynamic lubrication) point contact problem is solved using a new system-approach, similar to that introduced by Houpert and Hamrock for the line-contact problem. Introducing a body-fitted coordinate system, the troublesome free-boundary is transformed to a fixed domain. The Newton-Raphson method can then be used to determine the pressure distribution and the cavitation boundary subject to the Reynolds boundary condition. This method provides an efficient and rigorous way of solving the EHL point contact problem with the aid of a supercomputer and a promising method to deal with the transient EHL point contact problem. A typical pressure distribution and film thickness profile are presented and the minimum film thicknesses are compared with the solution of Hamrock and Dowson. The details of the cavitation boundaries for various operating parameters are discussed.

Lim, Sang Gyu↗

NASA NTRS1992

A system-approach to the elastohydrodynamic lubrication point-contact problem

Lim, Sang G.↗

NASA NTRS2000

Applications of Low Density Flow Techniques and Catalytic Recombination at the Johnson Space Center

The talk presents a brief background on defInitions of catalysis and effects associated with chemically nonequilibrium and low-density flows of aerospace interest. Applications of catalytic recombination on surfaces in dissociated flow are given, including aero heating on reentry spacecraft thermal protection surfaces and reflection of plume flow on pressure distributions associated with the space station. Examples include aero heating predictions for the X-38 test vehicle, the inlet of a proposed gas-sampling probe used in high enthalpy test facilities, and a parabolic body at angle of attack. The effect of accommodation coefficients on thruster induced pressure distributions is also included. Examples of tools used include simple aero heating formulas based on boundary layer solutions, an engineering approximation that uses axisymmetric viscous shock layer flow to simulate full three dimensional flow, full computational fluid dynamics, and direct simulation Monte-Carlo calculations. Methods of determining catalytic recombination rates in arc jet flow are discus ed. An area of catalysis not fully understood is the formation of single-wall carbon nanotubes (SWNT) with gas phase or nano-size metal particles. The Johnson Space Center is making SWNTs using both a laser ablation technique and an electric arc vaporization technique.

Scott, Carl D.↗

NASA NTRS1984

Development and applications of algorithms for calculating the transonic flow about harmonically oscillating wings

A finite difference method to solve the unsteady transonic flow about harmonically oscillating wings was investigated. The procedure is based on separating the velocity potential into steady and unsteady parts and linearizing the resulting unsteady differential equation for small disturbances. The differential equation for the unsteady velocity potential is linear with spatially varying coefficients and with the time variable eliminated by assuming harmonic motion. An alternating direction implicit procedure was investigated, and a pilot program was developed for both two and three dimensional wings. This program provides a relatively efficient relaxation solution without previously encountered solution instability problems. Pressure distributions for two rectangular wings are calculated. Conjugate gradient techniques were developed for the asymmetric, indefinite problem. The conjugate gradient procedure is evaluated for applications to the unsteady transonic problem. Different equations for the alternating direction procedure are derived using a coordinate transformation for swept and tapered wing planforms. Pressure distributions for swept, untaped wings of vanishing thickness are correlated with linear results for sweep angles up to 45 degrees.

Ehlers, F. E.↗

NASA NTRS1971

Thermal contact resistance in a non-ideal joint

The contact of two rough, wavy surfaces; the contact of two rough but nominally flat plates pressed together over a concentrated area; and the contact of two rough but nominally flat plates bolted together are considered. In each case the pressure distribution is calculated as a function of the surface properties. In the case of wavy surfaces it is found that all necessary information for any combination of parameters can be reduced to one master graph. In the other two cases one such graph is needed for each geometry used. The resulting pressure distributions are used in a specific heat transfer example and the total joint resistance versus roughness is presented. A method for decreasing the resistance by increasing the roughness is shown.

Roca, R. T.↗

NASA NTRS1978

Methods for calculating the transonic boundary layer separation for V/STOL inlets at high incidence angles

A semi-empirical scheme for the prediction of transonic pressure distribution on the surface of V/STOL inlets at high incidence angles has been developed. The investigation is intended to improve the boundary layer calculation and separation prediction by including the effects of shock wave-boundary layer interaction into the Lewis Inlet Viscous Computer Program. Wind-tunnel results and theoretical pressure calculation for critical cases are used in constructing the transonic pressure distribution. The program, which describes the development of the boundary layer and predicts the possible flow separation, can handle the cases of inlets at high incidence angles where local supersonic region may occur in the flow.

Chou, D. C.↗

NASA NTRS2018

Use of Simple Continuum Solutions in Finite Element Alternating Method for Fracture Problems

The performance of the finite element alternating (FEAM) method for two-dimensional crack problems is studied with respect to a polynomial pressure distribution fitted to the crack face stresses. The FEAM alternates between the analytical solution of crack in an infinite plate subjected to arbitrary polynomial distribution and a finite element solution of an uncracked body to satisfy the required boundary conditions in the crack problem. In this paper, the FEAM is applied to embedded crack and edge crack problems. For embedded crack problems, all of the constant, linear, and quadratic ( N=0,1, or 2, respectively) pressure distributions yield very accurate results with this algorithm with 4 to 5 iterations. The edge crack problems, on the other hand, require much higher order polynomials distributions (N=5 to 6) to yield accurate solutions. For slant edge crack problems, the mode-I stress-intensity factors have better accuracy than the mode-II stress-intensity factors for the same convergence tolerance.

Krishnamurthy, T.↗

NASA NTRS1976

FLEXSTAB analysis

The wing differential pressure distributions of two vehicles are predicted using FLEXSTAB. Three space shuttle configurations were investigated. Comparisons were made of wind tunnel and analytical data for a selected range of angle of attack, angle of sideslip, and Mach number. A drone-type vehicle was investigated and comparisons were made between flight and analytical data of wing pressure distributions and static longitudinal stability derivatives.

Lowder, H. E., Jr.↗