Search NASA⌕ Search

SEARCH · Search NASA

Results for “Phase 2”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Task 12 data dump (phase 2) OME integrated thrust chamber test report

The characteristics and performance of the orbit maneuvering engine for the space shuttle are discussed. Emphasis is placed on the regeneratively cooled thrust chamber of the engine. Tests were conducted to determine engine operating parameters during the start, shutdown, and restart. Characteristics of the integrated thrust chamber and the performance and thermal conditions for blowdown operation without supplementary boundary layer cooling were investigated. The results of the test program are presented.

Tobin, R. D.↗

Study for identification of Beneficial Uses of Space (BUS), phase 2. Volume 2: Technical report. Book 2: Section 5, appendices A through D

An investigation of the technology and programmatics involved in the development of four of the products selected as capable of benefitting from space manufacturing was conducted. The four activities selected are as follows: (1) levitation heating and melting of tungsten, (2) free suspension processing of oxides to form amorphous oxide materials, (3) crystals for surface wave acoustic substrates, and (4) space manufacturing of surface acoustic wave devices.

Source record↗

Fabrication of 1/3 scale boron/epoxy booster thrust structure, phase 2

The design, materials, tooling, various manufacturing processes, quality control, test procedures, and results associated with the fabrication and testing of a 1/3 scale boron/epoxy, booster thrust structure are described. A complete two-dimensional truss type thrust structure, comprised of nine boron/epoxy tubular members and six apex fittings, was fabricated. This resulted in structurally representative flight hardware, and verified the manufacturing feasibility and projected weight savings (30%) for this type of structure.

Source record↗

Design, fabrication, and test of lightweight shell structure, phase 2

A cylindrical shell skirt structure 4.57 m (180 in.) in diameter and 3.66 m (144 in.) high was subjected to a design and analysis study using a wide variety of structural materials and concepts. The design loading of 1225.8 N/cm (700 lb/in.) axial compression and 245.2 N/cm (140 lb/in.) torsion is representative of that expected on a typical space tug skirt section. Structural concepts evaluated included honeycomb sandwich, truss, isogrid, and skin/stringer/frame. The materials considered included a wide variety of structural metals as well as glass, graphite, and boron-reinforced composites. The most unique characteristic of the candidate designs is that they involve the use of very thin-gage material. Fabrication and structural test of small panels and components representative of many of the candidate designs served to demonstrate proposed fabrication techniques and to verify design and analysis methods.

Source record↗

TDRSS multimode transponder program. Phase 2: Equipment development

This report contains a complete description of the TDRS Multimode Transponder and its associated ground support equipment. The transponder will demonstrate candidate modulation techniques to provide the required information for the design of an eventual VHF/UHF transponder suitable for installation in a user satellite, capable of operating as part of a Tracking and Data Relay Satellite (TDRS) systems. Use of geosynchronous TDRS which can serve both low data rate users at VHF and high data rate users at other frequencies has been considered. The effects of radio frequency interference from the earth and of multipath propagation due to reflections from the earth are expected to pose problems for the TDRS system at VHF. Investigations have suggested several modulation techniques that offer promise to overcome these problems.

Cnossen, R. S.↗

Rubidium 87 gas cell studies, phase 2

The design, development, and characteristics of a rubidium 87 maser are discussed. The design of a receiver capable of locking a crystal oscillator to the maser signal is reported. The subjects considered are: (1) maser construction, (2) maser control electronics, (3) the characteristics of the receiver, and (4) results of experimental maser tests.

Vanier, J.↗

Generalized environmental control and life support system computer program (G189A) configuration control, phase 2

A method for updating and maintaining the G189A program library and documentation for all program users is provided. The effort also involves: (1) providing instruction and recommendations for the use and application of the program, (2) developing new subroutines and the logic required for new simulations, (3) supporting special analyses required by CSD, and (4) conduct studies to define and understand the interaction of the shuttle ECLSS and propose payload ECLSS and ECS designs.

Blakely, R. L.↗

Earth resources data analysis program, phase 2

The efforts and findings of the Earth Resources Data Analysis Program are summarized. Results of a detailed study of the needs of EOD with respect to an applications development system (ADS) for the analysis of remotely sensed data, including an evaluation of four existing systems with respect to these needs are described. Recommendations as to possible courses for EOD to follow to obtain a viable ADS are presented. Algorithmic development comprised of several subtasks is discussed. These subtasks include the following: (1) two algorithms for multivariate density estimation; (2) a data smoothing algorithm; (3) a method for optimally estimating prior probabilities of unclassified data; and (4) further applications of the modified Cholesky decomposition in various calculations. Little effort was expended on task 3, however, two reports were reviewed.

Source record↗

Ice pack heat sink subsystem, phase 2

The report describes the design, development, fabrication, and test at one gravity of a prototype ice pack heat sink subsystem to be used eventually for astronaut cooling during manned space missions; the investigation of thermal storage material with the objective of uncovering materials with heats of fusion and/or solution in the range of 300 Btu/lb (700 kilojoules/kilogram); and the planned procedure for implementing an ice pack heat sink subsystem flight experiment. In normal use, excess heat in the liquid cooling garment (LCG) coolant is transferred to a reusable/regenerable ice pack heat sink. For emergency operation, or for extension of extravehicular activity mission time after all the ice has melted, water from the ice pack is boiled to vacuum, thereby continuing to remove heat from the LCG coolant. This subsystem incorporates a quick disconnect thermal interface between the ice pack heat sink and the subsystem heat exchanger.

Roebelen, G. J., Jr.↗

Phase 2, 3 and 4 8 psi pressure glove

The feasibility of providing a high pressure, very mobile and reliable space suit glove system is demonstrated. A 'soft' toroidal wrist joint assembly was developed. A representative Kevlar and steel wrist section was tested and proved the useful lifetime to be in excess of 1,000,000 cycles. Improved comfort was accomplished by increasing the first finger metacarpal dimensions. Recommendations concern design refinements, and EVA configuration.

Elkins, W.↗

Storage stability and improvement of intermediate moisture foods, phase 2

Methods for improvement of shelf-life stability of intermediate moisture foods are considered. It was found that vitamin C is the most limiting vitamin from a nutritional standpoint with its rate of destruction increasing with a sub w. Techniques for microbial challenge studies were developed. It was shown that organisms have a higher growth a sub w limit if the IMF is prepared by the adsorption process and long times are needed for challenge studies. Several alternative antimycotic systems were found. It was also found that the vegetative cells of pathogens have a maximum heat resistance in the IMF a sub w range. If glycols are in the formula, the IMF should have as high an a sub w as possible. The reverse is true if lipid oxidation occurs. In addition, to prevent rancidity, antioxidants and a low O2 atmosphere are necessary. The package also must be a good moisture barrier.

Labuza, T. P.↗

Engineering flight and guest pilot evaluation report, phase 2

Prior to the flight evaluation, the two-segment profile capabilities of the DC-8-61 were evaluated and flight procedures were developed in a flight simulator at the UA Flight Training Center in Denver, Colorado. The flight evaluation reported was conducted to determine the validity of the simulation results, further develop the procedures and use of the area navigation system in the terminal area, certify the system for line operation, and obtain evaluations of the system and procedures by a number of pilots from the industry. The full area navigation capabilities of the special equipment installed were developed to provide terminal area guidance for two-segment approaches. The objectives of this evaluation were: (1) perform an engineering flight evaluation sufficient to certify the two-segment system for the six-month in-service evaluation; (2) evaluate the suitability of a modified RNAV system for flying two-segment approaches; and (3) provide evaluation of the two-segment approach by management and line pilots.

Morrison, J. A.↗

Hypersonic research engine project. Phase 2: Some combustor test results of NASA aerothermodynamic integration model

Combustor test results of the NASA Aerothermodynamic Integration Model are presented of a ramjet engine developed for operation between Mach 3 and 8. Ground-based and flight experiments which provide the data required to advance the technology of hypersonic air-breathing propulsion systems as well as to evaluate facility and testing techniques are described. The engine was tested with synthetic air at Mach 5, 6, and 7. The hydrogen fuel was heated to 1500 R prior to injection to simulate a regeneratively cooled system. Combustor efficiencies up to 95 percent at Mach 6 were achieved. Combustor process in terms of effectiveness, pressure integral factor, total pressure recovery and Crocco's pressure-area relationship are presented and discussed. Interactions between inlet-combustor, combustor stages, combustor-nozzle, and the effects of altitude, combustor step, and struts are observed and analyzed.

Sun, Y. H.↗

Hypersonic research engine project. Phase 2: Preliminary report on the performance of the HRE/AIM at Mach 6

Test results of the Aerothermodynamic Integration Model are presented. A program was initiated to develop a hydrogen-fueled research-oriented scramjet for operation between Mach 3 and 8. The primary objectives were to investigate the internal aerothermodynamic characteristics of the engine, to provide realistic design parameters for future hypersonic engine development as well as to evaluate the ground test facility and testing techniques. The engine was tested at the NASA hypersonic tunnel facility with synthetic air at Mach 5, 6, and 7. The hydrogen fuel was heated up to 1500 R prior to injection to simulate a regeneratively cooled system. The engine and component performance at Mach 6 is reported. Inlet performance compared very well both with theory and with subscale model tests. Combustor efficiencies up to 95 percent were attained at an equivalence ratio of unity. Nozzle performance was lower than expected. The overall engine performance was computed using two different methods. The performance was also compared with test data from other sources.

Sun, Y. H.↗

Phase 2 study of improved materials for use on Scout rocket motor nozzles

Nozzle material performance data were obtained, and the feasibility was determined of using new materials on the Scout rocket motor nozzles. Stress and heat transfer analyses were conducted to aid in the selection of optimum materials for nozzle tests. A reimpregnated and graphitized throat insert was fabricated along with two nozzles with ablative throats. The dissection and determining of char and erosion of two nozzles fired on X-259 loaded cases are discussed; one of the nozzles used a graphite phenolic ablative throat insert, and the other unit was a standard X-259 nozzle with a reduced area ATJ graphite throat insert.

Stutzman, R. D.↗

Support of imaging radar for the shuttle system and subsystem definition study, phase 2

An orbital microwave imaging radar system suggested for use in conjunction with the space shuttle is presented. Several applications of the system are described, including agriculture, meteorology, terrain analysis, various types of mapping, petroleum and mineral exploration, oil spill detection and sea and lake ice monitoring. The design criteria, which are based on the requirements of the above applications, are discussed.

Source record↗

Hypersonic research engine project. Phase 2: Aerothermodynamic Integration Model (AIM) test report

The Hypersonic Research Engine-Aerothermodynamic Integration Model (HRE-AIM) was designed, fabricated, and tested in the Hypersonic Tunnel Facility. The HRE-AIM is described along with its installation in the wind tunnel facility. Test conditions to which the HRE-AIM was subjected and observations made during the tests are discussed. The overall engine performance, component interaction, and ignition limits for the design are evaluated.

Andersen, W. L.↗