Search NASA⌕ Search

SEARCH · Search NASA

Results for “Pressure Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Long-term compression effects on elastomeric O-ring behavior

This paper discusses the results of testing performed on elastomeric seal materials that had been under compression for extended periods of time. Elastomeric seals used in the Space Shuttle redesigned solid rocket motors can experience compression times of up to six months. These seals must be capable of sealing internal motor pressure upon ignition. The tests described herein were performed in order to verify that the seals, which had experienced long-term compression could seal throughout motor operation. Testing was divided into two phases: (1) dynamic high pressure testing, and (2) resiliency testing. Dynamic testing was performed using specialized test fixtures that allowed simulation of the field joint movements during initial motor operation along with high pressure gas. Resiliency testing was performed using specialized test fixtures that also simulated field joint movements and also had the ability to measure the sealing force of the O-ring. Results from all testing indicated that the current elastomeric seals used in the redesigned solid rocket motors will seal during motor operations in the currently defined launch environments.

Clinton, R. G.↗
NASA NTRS2017

Low Pressure Flame Blowoff from the Forward Stagnation Region of a Blunt-Nosed Cast PMMA Cylinder in Axial Mixed Convective Flow

Low-pressure blowoff experiments were conducted with a stagnation flame stabilized on the forward tip of cast PMMA rods in a vertical wind tunnel. Pressure, forced flow velocity, gravity, and ambient oxygen concentration were varied. Stagnation flame blowoff is determined from a time-stamped video recording of the test. The blowoff pressure is determined from test section pressure transducer data that is synchronized with the time stamp. The forced flow velocity is also determined from the choked flow orifice pressure. Most of the tests were performed in normal gravity, but a handful of microgravity tests were also conducted to determine the influence of buoyant flow velocity on the blowoff limits. The blowoff limits are found to have a linear dependence between the partial pressure of oxygen and the total pressure, regardless of forced flow velocity and gravity level. The flow velocity (forced and/or buoyant) affects the blowoff pressure through the critical Damkohler number residence time, which dictates the partial pressure of oxygen at blowoff. This is because the critical stretch rate increases linearly with increasing pressure at low pressure (sub-atmospheric pressures) since a second-order overall reaction rate with two-body reactions dominates in this pressure range.

flammability↗
DOE OSTI2022

Quasi-static to Dynamic Response and Microstructure Development of Tantalum-Tungsten Alloys

Lawrence Livermore National Laboratory (LLNL) has a need to understand the quasi-static to dynamic mechanical response and microstructure evolution of tantalum-tungsten (Ta-W) alloys made by conventional wrought processing and additive manufacturing (AM). This two-year work scope will be performed at the Colorado School of Mines (Mines) and will include quasi-static (e.g., 10 -3 s -1 ) mechanical testing in tension and compression, along with high strain rate (Kolsky) pressure bar testing in tension and compression (e.g., 10 3 s -1 ), without and with temperature variations. Gas gun experiments at higher strain rates (e.g., over 10 3 s -1 ) will also be pursued. Complementary microstructure characterization will be performed on undeformed and deformed samples to fundamentally understand the role of processing on the microstructure characteristics and resulting deformation mechanisms that dictate the mechanical response of these alloys with variations in strain rate, temperature, and strain state. Alloys of interest will be Ta-based, containing up to 10 wt.% W. LLNL will supply initial wrought-processed material for sample machining. LLNL will also supply samples built by AM during the project for testing. Arc melting and casting may also be performed at Mines to produce small quantities of different alloys for machining and exploratory testing on an as-needed basis. This project will support multiple postdocs and graduate students at Mines, training them with the knowledge, skills, and abilities needed to study materials under extreme conditions of interest to the National Nuclear Security Agency.

36 MATERIALS SCIENCE↗
NASA NTRS2008

Visualization of Flowfield Modification by RCS Jets on a Capsule Entry Vehicle

Nitric oxide planar laser-induced fluorescence (NO PLIF) has been used to visualize the flow on the aft-body of an entry capsule having an activated RCS jet in NASA Langley Research Center's 31-Inch Mach 10 wind tunnel facility. A capsule shape representative of the Apollo command module was tested. These tests were performed to demonstrate the ability of the PLIF method to visualize RCS jet flow while providing some preliminary input to NASA's Orion Vehicle design team. Two different RCS nozzle designs - conical and contoured - were tested. The conical and contoured nozzles had area ratios of 13.4 and 22.5 respectively. The conical nozzle had a half-angle of 10 . Low- and high-Reynolds number cases were investigated by changing the tunnel stagnation pressure from 350 psi to 1300 psi, resulting in freestream Reynolds numbers of 0.56 and 1.8 million per foot respectively. For both of these cases, three different jet plenum pressures were tested (nominally 56, 250 and 500 psi). A single angle-of-attack was investigated (24 degrees). NO PLIF uses an ultraviolet laser sheet to interrogate a slice in the flow containing seeded NO; this UV light excites fluorescence from the NO molecules which is detected by a high-speed digital camera. The system has spatial resolution of about 200 microns (2 pixel blurring) and has flow-stopping time resolution (approximately 1 microsecond). NO was seeded into the flow two different ways. First, the RCS jet fluid was seeded with approximately 1-5% NO, with the balance N2. This allowed observation of the shape, structure and trajectory of the RCS jets. Visualizations of both laminar and turbulent flow jet features were obtained. Visualizations were obtained with the tunnel operating at Mach 10 and also with the test section held at a constant pressure similar to the aftbody static pressure (0.04 psi) obtained during tunnel runs. These two conditions are called "tunnel on" and "tunnel off" respectively. Second, the forebody flow was seeded with a very low flowrate (<100 standard cubic centimeters per minute) of pure NO. This trace gas was entrained into and allowed visualization of the shear layer forming between the expansion fan on the shoulder of the model and the recirculating separated flow in the wake of the model. This shear layer was observed to be laminar in the absence of the RCS jet operation and turbulent above a certain RCS jet flowrate. Furthermore, the operation of the RCS jet is seen to push the shear layer out away from the model, with a higher jet pressures resulting in larger deflections. Figures show some data from this test, partially processed. In the final paper, these images will be processed and rendered on a three dimensional visualization of the test hardware for clearer visualization and interpretation of the flowfields.

Danehy, P. M.↗
NASA NTRS1946

Tests of a 1/5-Scale Model of the Republic XP-84 Airplane (Army Project MX-578) in the Langley 300 MPH 7- by 10-Foot Tunnel

A 1/5-scale model of the Republic x-84 airplane (Army Project MX-578) was tested in the Langley 300 MPH 7- by 10-foot tunnel. The primary object of the tests was twofold: to determine, a practicable method of increasing the longitudinal 3tability in the landing configuration, and to investigate the effects on longitudinal and lateral Stability of various external stored (fuel tanks, bombs, and rockets). The effects of the fuselage dive brakes were also determined, and the critical Mach numbers of certain of the airplane components were estimated. The use of the revised horizontal tail (of larger aspect ratio and area than the original) seemed to be the most feasible expedient for materially increasing the longitudinal stability in the landing configuration. The neutral-point shifts produced by the various external stores were unstable, the largest shift being about 2.5 percent mean aerodynamic chord. No appreciable aerodynamic trim changes were caused by the external stores. From the standpoint of range, maximum s peed, and rate of climb, the advantages of mounting the fuel tanks at the wing tips rather than inboard beneath the wings were clearly demonstrated by the tests. The effective dihedral parameter was the only static lateral-stability derivative appreciably affected by the external stores. At high lift coefficients, the tip-mounted tanks caused a large increase in the effective dihedral parameter (about 40 increase at a lift coefficient of 1.0). This increase was held undesirable, because the tendency toward oscillatory instability that it would cause would be heightened by the increased moments of inertia resulting from the weight of the tanks when carrying fuel. The fuselage dive brakes, when deflected, caused a change in trim tending to nose the airplane up; the neutral point also moved rearward upon deflecting the dive brakes. The amount of elevator required to overcome the change in trim was well within the available range of deflection. It was estimated that a drive-brake deflection of 900 would.decrease the terminal Mach number in a vertical dive by about 0.1. The estimated critical Mach number of the V-front canopy was about 0.04 greater than that of the original canopy. Pressure-distribution tests disclosed severe pressure peaks inside the nose of the jet entrance duct. These peaks, which would lead to separation and consequently poor pressure recovery at, the engine, could be reduced by, using a smaller nose,radius and: a modified internal lip shape

Tucker, Warren A.↗
NASA NTRS1943

Effect of Normal Pressure on the Critical Shear Stress of Curved Sheet

In order to determine the critical stresses caused by an outward acting pressure on the upper surface of a wing due to the difference in internal and external pressures, torsional tests were made on two curved-sheet specimens subjected to an outward acting normal pressure. Results show that an outward acting normal pressure appreciable raises the critical shear stress for an unstiffened curved sheet; the absolute increase in critical shear stress is slightly greater for a 30 in. rib spacing than for a 10 in. rib spacing.

TESTING MACHINES, STRESS - NACA↗
NASA NTRS2006

Marshall Space Flight Center Autumn 2005

The East Test Area at Marshall Space Flight Center has five major test stands, each of which has two or more test positions, not counting the SSME and RD-180 engine test facilities in the West Test Area. These research and development facilities are capable of testing high pressure pumps, both fuel and oxidizer, injectors, chambers and sea-level engine assemblies, as well as simulating deep space environments in the 12, 15 and 20 foot vacuum chambers. Liquid propellant capabilities are high pressure hydrogen (liquid and gas), methane (liquid and gas), and RP-1 and high pressure LOX. Solid propellant capability includes thrust measurement and firing capability up to 1/6 scale Shuttle SRB segment. In the past six months MSFC supported multiple space access and exploration programs in the previous six months. Major programs were Space Exploration, Shuttle External Tank research, Reusable Solid Rocket Motor (RSRM) development, as well as research programs for NASA and other customers. At Test Stand 115 monopropellant ignition testing was conducted on one position. At the second position multiple ignition/variable burn time cycles were conducted on Vacuum Plasma Spatter (VPS) coated injectors. Each injector received fifty cycles; the propellants were LOX Hydrogen and the ignition source was TEA. Following completion of the monopropellant test series the stand was reconfigured to support ignition testing on a LOX Methane injector system. At TS 116 a thrust stand used to test Booster Separation Motors from the Shuttle SRB system was disassembled and moved from Chemical Systems Division s Coyote Canyon plant to MSFC. The stand was reassembled and readied for BSM testing. Also, a series of tests was run on a Pratt & Whitney Rocketdyne Low Element Density (LED) injector engine. The propellants for this engine are LOX and LH2. At TS 300 the 20 foot vacuum chamber was configured to support hydrogen testing in the Multipurpose Hydrogen Test Bed (MHTB) test article. This testing, which went 24/7 for fourteen consecutive days, demonstrated long duration storage methods intended to minimize losses of propellant in support of the Space Exploration Initiative. The facility is being converted to support similar research using liquid methane. The 12 foot chamber at TS 300 was used to create ascent profiles (both heat and altitude effects) for foam panel testing in support of the Shuttle External Tank program. At TS 500, one position was in build-up to support ATK Thiokol research into the gas dynamics associated with high pressure flow across the propellant joint in segmented solid rocket motors. The testing involves flowing high pressure gas through a 24 motor case. Initial tests will be conducted with simulated aluminum grain, followed by tests using actual propellant. The second position at TS 500 has been in build-up for testing a LOX methane thruster manufactured by KT Engineering. At the Solid Propulsion Test Area (SPTA), the first dual segment 24 solid rocket motor was fired for ATK Thiokol in support of the RSRM program. A new axial thrust measurement stand was designed and fabricated for this testing. Real Time Radiography (RTR) will be deployed to examine nozzle erosion on the next dual segment motor.

Allen, Mike↗
NASA NTRS1982

Ceramic thermal barrier coatings for gas turbine engines

The results of studies concerning the high temperature corrosion resistance of ZrO2-Y2O3, ZrO2-MgO, and Ca2SiO4 plasma-sprayed coatings, which may be used as gas turbine engine thermal barriers, are reported. The coatings were evaluated in atmospheric burner rig and pressurized passage tests, using GT No. 2 fuel in pure form and with sodium, sulfur and vanadium corrosive impurities doping. It is found that, while the coatings performed well in both pressurized passage and burner rig tests with pure fuel chemical reactions between the ceramic coatings and combustion gases/condensates resulted in coating degradation with impure fuels. Chemical reactions between the ceramic coatings and vanadium compounds played a critical role in coating degradation.

Bratton, R. J.↗
NASA NTRS2012

Checkout and Standard Use Procedures for the Mark III Space Suit Assembly

The operational pressure range is the range to which the suit can be nominally operated for manned testing. The top end of the nominal operational pressure range is equivalent to 1/2 the proof pressure. Structural pressure is 1.5 times the specified test pressure for any given test. Proof pressure is the maximum unmanned pressure to which the suit was tested by the vendor prior to delivery. The maximum allowable working pressure (MAWP) is 90% of the proof pressure. The pressure systems RVs are set to keep components below their MAWPs. If the suit is pressurized over its MAWP, the suit will be taken out of service and an in-depth inspection/review of the suit will be performed before the suit is put back in service. The procedures outlined in this document should be followed as written. However, the suit test engineer (STE) may make redline changes real-time, provided those changes are recorded in the anomaly section of the test data sheet. If technicians supporting suit build-up, check-out, and/or test execution believe that a procedure can be improved, they should notify their lead. If procedures are incorrect to the point of potentially causing hardware damage or affecting safety, bring the problem to the technician lead and/or STE s attention and stop work until a solution (temporary or permanent) is authorized. Certain steps in the procedure are marked with a DV , for Designated Verifier. The Designated Verifier for this procedure is an Advanced Space Suit Technology Development Laboratory technician, not directly involved in performing the procedural steps, who will verify that the step was performed as stated. The steps to be verified by the DV were selected based on one or more of the following criteria: the step was deemed significant in ensuring the safe performance of the test, the data recorded in the step is of specific interest in monitoring the suit system operation, or the step has a strong influence on the successful completion of test objectives. Prior to all manned test activities, Advanced Suit Test Data Sheet (TDS) Parts A-E shall be completed to verify system and team are ready for test. Advanced Suit TDS Parts F-G shall be completed at the end of the suited activity. Appendix B identifies tha appropriate Mark III suit emergency event procedures.

Valish, Dana J.↗
DOE OSTI2019

Mechanical Behavior of Lead at High Strain Rates

This paper presents a study on the material behaviors and constitutive models of lead at high strain rates. Quasi-static compressive tests and split Hopkinson pressure bar (SHPB) tests were conducted at room temperature. The results of the SHPB tests were verified by high-speed photography, and the error of strain is less than 3% at high strain rate (5000/s). Our results show that the yield stress and flow stress increase at high strain rates. This result indicates that lead is sensitive to the strain rate at high strain rates, but the dependence is not linear during 3000-5000/s. The strain-rate dependence of lead was fitted by a quadratic polynomial curve. To describe the nonlinear strain-rate relationship of lead, modified Johnson–Cook and Cowper–Symonds material models were used to fit the experimental stress–strain curves. The modified Cowper–Symonds model agrees better with the experimental results and can better describe the dynamic mechanical behavior of lead under high strain rates.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Quasi-static to Dynamic Mechanical Response and Microstructure Development of Tantalum-Tungsten Alloys

Lawrence Livermore National Laboratory (LLNL) is interested the quasi-static to dynamic mechanical response and microstructure evolution of tantalum-tungsten (Ta-W) alloys (Ta-2.5W, Ta-5W, and Ta-10W, wt.%) made by conventional wrought processing and additive manufacturing (AM). This work scope was performed at the Colorado School of Mines (Mines) and included quasi-static (e.g., 10 -3 s -1 ) mechanical testing in tension and compression, along with selected high strain rate (Kolsky) pressure bar testing in compression (e.g., 10 3 s -1 ), with and without temperature variations in some instances. Complementary microstructure characterization was performed on undeformed and deformed samples to understand the role of processing on microstructural evolution and the deformation mechanisms that impact the mechanical response with variations in strain rate, temperature, and strain state (e.g., tension versus compression in selected examples). The wrought material provided by LLNL from Viridis Materials was found to have unrecrystallized regions within the microstructure, which led to unexpected results relative to previously reported properties for Ta-W. The AM Ta-2.5W (wt.%) material provided by LLNL was found to have higher compressive strength than wrought Ta-2.5W (wt.%), which is hypothesized to be due to differences in the crystallographic texture between the two materials. This project partially supported several postdocs and graduate students at Mines.

36 MATERIALS SCIENCE↗
NASA NTRS1977

Experimental evaluation of premixing-prevaporizing fuel injection concepts for a gas turbine catalytic combustor

Experiments were performed to evolve and evaluate a premixing-prevaporizing fuel system to be used with a catalytic combustor for possible application in an automotive gas turbine. Spatial fuel distribution and degree of vaporization were measured using Jet A fuel. Three types of air blast injectors, an air assist nozzle and a simplex pressure atomizer were tested. Air swirlers with vane angles up to 30 deg were used to improve the spatial fuel distribution. The work was done in a 12-cm (4.75-in.) diameter tubular rig. Test conditions were: a pressure of 0.3 and 0.5 MPa (3 and 5 atm), inlet air temperatures up to 800 K (980 F), velocity of 20 m/sec (66 ft/sec) and fuel-air ratios of 0.01 and 0.025. Uniform spatial fuel distributions that were within plus or minus 10 percent of the mean were obtained. Complete vaporization of the fuel was achieved with air blast configurations at inlet air temperatures of 550 K (530 F) and higher. The total pressure loss was less than 0.5 percent for configurations without air swirlers and less than 1 percent for configurations with a 30 deg vane angle air swirler.

Tacina, R. R.↗
NASA NTRS1980

Flow field and acoustic properties of a Mach number 0.9 jet at a low Reynolds number

An experimental study of the flow field and acoustic properties of a low Reynolds number M = 0.9 jet has been performed in a low pressure anechoic test chamber. The mean flow field was surveyed with a conventional pitot pressure probe and flow fluctuations were detected with a normal hot wire probe. Also, condenser microphone measurements were made in the acoustic field. The flow fluctuations within the jet were found to be dominated initially by a relatively discrete, large-scale, wave-like instability centered around a Strouhal number of 0.44. The axial wavelength of this instability was determined to be 1.45 jet diameters and its azimuthal character includes the n = 0 and n = plus or minus 1 modes. The growth of this instability coupled with its nonlinear breakdown are major contributors to the termination of the potential core region of the jet. The acoustic field of the jet, in contrast to the flow field, has a broad frequency spectrum with a peak amplitude near a Strouhal number of St = 0.2. The results indicate that a nonlinear mechanism involving the large-scale flow instability is responsible for a dominant portion of the noise generated from this jet.

Stromberg, J. L.↗
NASA NTRS1986

The NASA modern technology rotors program

Existing data bases regarding helicopters are based on work conducted on 'old-technology' rotor systems. The Modern Technology Rotors (MTR) Program is to provide extensive data bases on rotor systems using present and emerging technology. The MTR is concerned with modern, four-bladed, rotor systems presently being manufactured or under development. Aspects of MTR philosophy are considered along with instrumentation, the MTR test program, the BV 360 Rotor, and the UH-60 Black Hawk. The program phases include computer modelling, shake test, model-scale test, minimally instrumented flight test, extensively pressure-instrumented-blade flight test, and full-scale wind tunnel test.

Watts, M. E.↗
NASA NTRS1991

Slush hydrogen propellant production, transfer, and expulsion studies at the NASA K-Site Facility

Slush hydrogen is currently being considered as a fuel for the National AeroSpace Plane (NASP) because it offers the potential for decreased vehicle size and weight. However, no large scale data was available on the production, transfer, and tank pressure control characteristics required to use the fuel for the NASP. Therefore, experiments were conducted at NASA-Lewis K-Site Facility to improve the slush hydrogen data base. Slush hydrogen was produced using the evaporative cooling, or freeze-thaw, technique in batches for approx. 800 gallons. This slush hydrogen was pressure transferred to a 5 ft diameter spherical test tank following production, and flow characteristics were measured during this transfer process. The slush hydrogen in the test tank was pressurized and expelled using a pressurized expulsion technique to obtain information on tank pressure control for the NASP. Results from the production, transfer, pressurization, and pressurized expulsion tests are described.

Hardy, Terry L.↗