Search NASA⌕ Search

SEARCH · Search NASA

Results for “Rock sampling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Test and Delivery of the Chemin Mineralogical Instrument for Mars Science Laboratory

The CheMin mineralogical instrument on MSL will return quantitative powder X-ray diffraction data (XRD) and qualitative X-ray fluorescence data (XRF; 14<Z<92) from scooped soil samples and drilled rock powders collected on the Mars surface. The geometry of the source, sample, and detector is shown. A transmission geometry was chosen so that diffracted intensities in the low-20 region (5-15 deg), important for phyllosilicate identification, could be detected.

Blake, D. F.↗

Development of Sample Verification System for Sample Return Missions

This paper describes the development of a proof of-concept sample verification system (SVS) for in-situ mass measurement of planetary rock and soil sample in future robotic sample return missions. Our proof-of-concept SVS device contains a 10 cm diameter pressure sensitive elastic membrane placed at the bottom of a sample canister. The membrane deforms under the weight of accumulating planetary sample. The membrane is positioned in proximity to an opposing substrate with a narrow gap. The deformation of the membrane makes the gap to be narrower, resulting in increased capacitance between the two nearly parallel plates. Capacitance readout circuitry on a nearby printed circuit board (PCB) transmits data via a low-voltage differential signaling (LVDS) interface. The fabricated SVS proof-of-concept device has successfully demonstrated approximately 1pF/gram capacitance change

Electrodes↗

Brief review of thermoluminescence studies in lunar samples.

A weak thermoluminescence, due primarily to plagioclase feldspar, is found to exist in Apollo 11 and 12 lunar rock and topsoil samples. This effect increases with depth to about 10 cm below the surface and becomes relatively even in greater depth. The penetration of the diurnal temperature wave is traced to the rock thermoluminescence. Evidence is also found for the thermal draining of the surface rock.

Hoyt, H. P., Jr.↗

MOD: An Organic Detector for the Future Exploration of Mars

The Mars Organic Detector (MOD) is designed to assess whether organic compounds, possibly associated with life, are present in Martian rock and soil samples. MOD has a detection limit that is at least two orders of magnitude more sensitive than the Viking GCMS. MOD is focused on detecting amino acids, amines and PAH (polycyclic aromatic hydrocarbons). Amino acids play an essential role in biochemistry on Earth and PAH are widespread throughout the universe and can provide an indication of the delivery of meteoritic organic material to Mars. The advantage of MOD is the absence of wet chemistry and its simple and robust design. The sample will be extracted from the mineral matrix (0.1 - 1 g of rock-powder) using sublimation and analyzed with a fluorescence detector. The isolation method is based on the fact that amino acids and PAH are volatile at temperatures greater than 150C. The fluorescence detection scheme is based on UV excitation with LED's, optical filters, PrN diode photon detector and a sample calibration reservoir. Fluorescamine is used as a fluorescing reagent for amino acids and amines, while PAH are naturally fluorescent. There is no sample preparation required and the turnaround time for a single analysis is on the order of minutes.

Kminek, G.↗

Chemical, mineralogical and textural systematics of non-mare melt rocks: Implications for lunar impact and volcanic processes

Based on a synthesis of chemical data for over 200 samples, the nonmare rocks with fine grained melt textures can be classified into 7 major groups: anorthositic basalts, troctolitic basalts, VHA basalts, Apollo 14-type KREEP basalts, Apollo 15-type KREEP basalts, Apollo 17-type KREEP basalts, and aluminous mare basalts. Review of chemical, mineralogical, textural and experimental evidence leads to preferred hypotheses for the origins of these rocks; those hypotheses are discussed in detail.

Irving, A. J.↗

Science Café April 2021: Fetching Samples from Mars

Perseverance rover recently landed in an ancient lakebed on Mars. Its mission is to collect rock and soil samples, and place these in strategic locations for a future mission to return them to Earth. This talk provides an overview of the combined effort between NASA and the European Space Agency to bring those samples home. This involves the use of a small, but highly mobile rover, nicknamed ‘Fetch’. Fetch rover will be the first Mars rover to use flexible tires known as Spring Tires. These tires were invented in the Cleveland area by NASA and Goodyear. The benefits and challenges of this technology will be discussed in the context of this Mars mission, future missions, as well as on Earth. Note: To view full presentations with embedded video please download and permit 3D video imaging for this document.

Mars Sample Return↗

A Thorium-rich Mare Basalt Rock Fragment from the Apollo 12 Regolith: A Sample from a Young Procellarum Flow?

In this abstract, we report on the composition, mineralogy and petrography of a basaltic rock fragment, 12032,366-18, found in the Apollo 12 regolith. Age data, collected as part of an investigation by Barra et al., will be presented in detail in. Here, only the age dating result is summarized. This rock fragment garnered our attention because it is significantly enriched in incompatible elements, e.g., 7 ppm thorium, compared to other known lunar basalts. Its mineral- and trace-element chemistry set it apart from other Apollo 12 basalts and indeed from all Apollo and Luna basalts. What makes it potentially very significant is the possibility that it is a sample of a relatively young, thorium-rich basalt flow similar to those inferred to occur in the Procellarum region, especially northwestern Procellarum, on the basis of Lunar Prospector orbital data. Exploiting the lunar regolith for the diversity of rock types that have been delivered to a landing site by impact processes and correlating them to their likely site of origin using remote sensing will be an important part of future missions to the Moon. One such mission is Moonrise, which would collect regolith samples from the South Pole-Aitken Basin, concentrating thousands of rock fragments of 3-20 mm size from the regolith, and returning the samples to Earth.

Jolliff, B. L.↗

Improved Aerothermal Reliability Analysis Enabled by the Mars Sample Return Earth Entry System Aerothermal Database

The Mars Sample Return (MSR) campaign is a series of missions designed to retrieve Martian rock and soil samples for detailed study on Earth. The campaign is split into three primary phases: sample collection with the Mars2020 rover, retrieval with the Sample Return Lander (SRL) and Mars Ascent Vehicle (MAV), and then return to Earth with the Earth Return Orbiter (ERO) and Capture, Containment, and Return System (CCRS) [1]. The final sequence in the Earth return phase is the delivery and entry of the Earth Entry System (EES) sample return capsule. Due to unprecedented planetary protection concerns, the sample return capsule is subject to strict reliability requirements. To this end, the MSR-EES aerothermal team has implemented a flexible aerothermal database architecture capable of integration with state-of-the-art trajectory codes to provide a more rigorous aerothermal reliability analysis. The EES database enables the generation of environments at any location on the heatshield and can incorporate trajectory uncertainties to both statistically quantify aerothermal environments for arcjet testing and produce material response boundary conditions to rigorously select thermal protection system (TPS) sizing environments. This poster will not discuss the fundamental modeling assumptions included in the database, and will instead focus on the downstream reliability analyses that can be performed with a database of this architecture.

MSR-EES↗

Multivariate Methods for Prediction of Geologic Sample Composition with Laser-Induced Breakdown Spectroscopy

Laser-induced breakdown spectroscopy (LIBS) uses pulses of laser light to ablate a material from the surface of a sample and produce an expanding plasma. The optical emission from the plasma produces a spectrum which can be used to classify target materials and estimate their composition. The ChemCam instrument on the Mars Science Laboratory (MSL) mission will use LIBS to rapidly analyze targets remotely, allowing more resource- and time-intensive in-situ analyses to be reserved for targets of particular interest. ChemCam will also be used to analyze samples that are not reachable by the rover's in-situ instruments. Due to these tactical and scientific roles, it is important that ChemCam-derived sample compositions are as accurate as possible. We have compared the results of partial least squares (PLS), multilayer perceptron (MLP) artificial neural networks (ANNs), and cascade correlation (CC) ANNs to determine which technique yields better estimates of quantitative element abundances in rock and mineral samples. The number of hidden nodes in the MLP ANNs was optimized using a genetic algorithm. The influence of two data preprocessing techniques were also investigated: genetic algorithm feature selection and averaging the spectra for each training sample prior to training the PLS and ANN algorithms. We used a ChemCam-like laboratory stand-off LIBS system to collect spectra of 30 pressed powder geostandards and a diverse suite of 196 geologic slab samples of known bulk composition. We tested the performance of PLS and ANNs on a subset of these samples, choosing to focus on silicate rocks and minerals with a loss on ignition of less than 2 percent. This resulted in a set of 22 pressed powder geostandards and 80 geologic samples. Four of the geostandards were used as a validation set and 18 were used as the training set for the algorithms. We found that PLS typically resulted in the lowest average absolute error in its predictions, but that the optimized MLP ANN and the CC ANN often gave results comparable to PLS. Averaging the spectra for each training sample and/or using feature selection to choose a small subset of wavelengths to use for predictions gave mixed results, with degraded performance in some cases and similar or slightly improved performance in other cases. However, training time was significantly reduced for both PLS and ANN methods by implementing feature selection, making this a potentially appealing method for initial, rapid-turn-around analyses necessary for Chemcam's tactical role on MSL. Choice of training samples has a strong influence on the accuracy of predictions. We are currently investigating the use of clustering algorithms (e.g. k-means, neural gas, etc.) to identify training sets that are spectrally similar to the unknown samples that are being predicted, and therefore result in improved predictions

Morris, Richard↗

Method for Cleanly and Precisely Breaking Off a Rock Core Using a Radial Compressive Force

The Mars Sample Return mission has the goal to drill, break off, and retain rock core samples. After some results gained from rock core mechanics testing, the realization that scoring teeth would cleanly break off the core after only a few millimeters of penetration, and noting that rocks are weak in tension, the idea was developed to use symmetric wedging teeth in compression to weaken and then break the core at the contact plane. This concept was developed as a response to the break-off and retention requirements. The wedges wrap around the estimated average diameter of the core to get as many contact locations as possible, and are then pushed inward, radially, through the core towards one another. This starts a crack and begins to apply opposing forces inside the core to propagate the crack across the plane of contact. The advantage is in the simplicity. Only two teeth are needed to break five varieties of Mars-like rock cores with limited penetration and reasonable forces. Its major advantage is that it does not require any length of rock to be attached to the parent in order to break the core at the desired location. Test data shows that some rocks break off on their own into segments or break off into discs. This idea would grab and retain a disc, push some discs upward and others out, or grab a segment, break it at the contact plane, and retain the portion inside of the device. It also does this with few moving parts in a simple, space-efficient design. This discovery could be implemented into a coring drill bit to precisely break off and retain any size rock core.

Richardson, Megan↗

Study of sample drilling techniques for Mars sample return missions

To demonstrate the feasibility of acquiring various surface samples for a Mars sample return mission the following tasks were performed: (1) design of a Mars rover-mounted drill system capable of acquiring crystalline rock cores; prediction of performance, mass, and power requirements for various size systems, and the generation of engineering drawings; (2) performance of simulated permafrost coring tests using a residual Apollo lunar surface drill, (3) design of a rock breaker system which can be used to produce small samples of rock chips from rocks which are too large to return to Earth, but too small to be cored with the Rover-mounted drill; (4)design of sample containers for the selected regolith cores, rock cores, and small particulate or rock samples; and (5) design of sample handling and transfer techniques which will be required through all phase of sample acquisition, processing, and stowage on-board the Earth return vehicle. A preliminary design of a light-weight Rover-mounted sampling scoop was also developed.

Mitchell, D. C.↗

Thermal Design, Analysis, and Sensitivity of a Sample Tube on the Martian Surface

NASA will launch a rover to Mars in 2020 to collect and cache samples of Martian rocks and regolith for potential return to Earth on a future mission. The collected samples will be placed in tubes, hermetically sealed, and deposited on the surface of Mars for a period of up to 10 years. Preventing the deposited samples from overheating is an important consideration in order to ensure their scientific integrity. The samples are required to remain below 60 °C, however there is a goal to keep them below 40 °C. This temperature requirement is challenging, considering that the maximum surface temperature of Mars is 38 °C and the tube must be thermally controlled through only passive means. As a result, a significant effort has been made to design a tube to contain the samples and investigate innovative tube surface treatments that maintain proper sample temperatures without significant adverse effects of sample contamination. The tube uses a specialized aluminum oxide coating to prevent overheating on the Martian surface. The maximum predicted tube temperature is relatively insensitive to local thermal inertia, ground contact, and ground slope, but is very sensitive to landing site latitude and dust deposition. The maximum predicted sample temperature in the +/- 30° landing latitude range with worst case assumptions is 54 °C, but many of the potential landing sites have significantly cooler maximum predicted sample temperatures. This paper describes the thermal design, analysis, and sensitivity studies performed on the sample tubes and also discusses operational considerations.

Novak, Keith↗

MSR Curation Technology Development – Developing Protocols for Pre-Basic Characterization Measurements

The joint NASA/ESA Mars Sample Return (MSR) campaign could deliver to Earth the first pristine Mar-tian rock and regolith samples, collected by the Mars2020 science mission, Perseverance. In preparation for their arrival, the NASA/ESA Joint Curation Office (JCO) within the Sample Receiving Project (SRP) is developing curation technology needed to perform initial characterization of the samples while isolating samples from the Earth’s biosphere and protecting the samples from terrestrial contamination. (RSTA; Fig. 1). The Mars Sample Return Planning Group 2 (MSPG2) identified methods for achieving an array of potential science objectives for MSR outlined by the International MSR Objectives and Samples Team (iMOST) [1]. One category of methods, called Pre-Basic Characterization, recommends potential analyses that would happen before the Returnable Sample Tube Assemblies (RSTA; Figure 1) are opened: 1) Magnetometer & Magnetic Susceptibility; 2) X-ray Computed Tomography (XCT) Scanner [2]. To be in compliance with planetary protection requirements, and to limit the amount of time sample tubes are out-side of an isolated contamination-controlled environment, secondary containment is necessary. A Sample Tube Isolation Container (STIC) and Secondary Outer Containment Case (SOCC) is currently being developed at NASA JPL under the direction of the SRP JCO.

V Tu↗

Lunar highland melt rocks - Chemistry, petrology and silicate mineralogy

A selected suite containing several of the largest samples of lunar highland melt rocks includes impact melt specimens (anorthositic gabbro, low-K Fra Mauro) and volcanic specimens (intermediate-K Fra Mauro). Although previous assumptions of LKFM volcanism have fallen into disfavor, no fatal arguments against this hypothesis have been presented, and the evidence of a possibly 'inherited igneous' olivine-plagioclase cosaturation provides cause for keeping a volcanic LKFM hypothesis viable. Comparisons of silicate mineralogy with melt rock compositions provide information on the specimen's composition and cooling history. Plagioclase-rock compositions can be matched to the experimentally determined equilibria for appropriate samples to identify melt rocks with refractory anorthitic clasts. Olivine-rock compositions indicate that melt rock vitrophyres precipitate anomalously Fe-rich olivine; the cause of this anomaly is not immediately evident. The Al-Ti and Ca-Fe-Mg zonation in pyroxene provide information on relative cooling rates of highland melt rocks, but Cr- and Al-content (where Al-rich low-Ca pyroxene cores are preserved in rapidly cooled samples) can be correlated with composition of the host rock.

Vaniman, D. T.↗

Strontium and oxygen isotope study of M-1, M-3 and M-4 drill core samples from the Manson impact structure, Iowa: Comparison with Haitian K-T impact glasses

Strontium and oxygen isotope analyses were performed on 8 samples from the M-1, M-3, and M-4 cores recently drilled at the Manson impact structure. The samples were three elastic sedimentary rocks (of probable Cretaceous age) which occurred as clasts within the sedimentary clast breccia, two samples of crystalline rock breccia matrix, and three samples of dolomite and limestone. The Sr-87/Sr-86 (corrected to 65 Ma) ratios were much higher than those in impact glasses from the Haitian Cretaceous-Tertiary (K-T) boundary. Isotope mixing calculations demonstrate that neither the silicate or carbonate rocks analyzed from the Manson crater, or mixtures of these rocks are appropriate source materials for the Haitian impact glasses. However, the Sr-87/Sr-86 (65Ma) ratio and delta O-18 value of the Ca-rich Haitian glasses are well reproduced by mixtures of Si-rich Haitian glass with platform carbonate of K-T age.

Blum, Joel D.↗