Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS CALCULATIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Effects of bolt-hole contact on bearing-bypass damage-onset strength

A combined experimental and analytical study was conducted to investigate the effects of bolt-hole contact on the bearing bypass strength of a graphite-epoxy laminate. Tests were conducted on specimens consisting of 16-ply quasi-isotropic T300/5208 laminates with a centrally located hole. Bearing loads were applied through a clearance-fit steel bolt. Damage onset strength and damage mode were determined for each test case. A finite element procedure was used to calculate the bolt-hole stresses and bolt contact for each test case. A finite element procedure was used to calculate the bolt-hole stresses and bolt contact for each measured damage-onset strength. For the tension bearing-bypass cases tested, the bolt contact half-angle was approximately 60 degrees at damage onset. For compression, the contact angle was 20 degrees as the bypass load increased. A corresponding decrease in the bearing damage onset strength was attributed to the decrease in contact angle which made the bearing loads more severe. Hole boundary stresses were also computed by superimposing stresses for separate bearing and bypass loading. Stresses at the specimen net section were accurately approximated by the superposition procedure. However, the peak bearing stresses had large errors because the bolt contact angles were not represented correctly. For compression, peak bearing stress errors of nearly 50 percent were calculated.

Crews, John H., Jr.↗

Strain Rate Dependency of Simulated Welding Residual Stresses

In the present work, the influence of taking into consideration the strain rate-dependent nature of steel S355 during a calculation of the welding residual stresses through a finite element simulation is investigated. The Perzyna material model is calibrated using experimental values found in the literature and is introduced to a validated weld simulation model, where the strain rate dependency had not been taken into consideration before this study. The calculated profiles of the welding residual stresses, for strain rate-dependent and independent behavior, are then compared with experimentally measured profiles. The results of this first-step analysis show that taking into consideration strain rate dependency during a welding simulation of the investigated S355 has non-negligible influence on the calculated welding residual stresses.

36 MATERIALS SCIENCE↗

ROCOPT: A user friendly interactive code to optimize rocket structural components

ROCOPT is a user-friendly, graphically-interfaced, microcomputer-based computer program (IBM compatible) that optimizes rocket components by minimizing the structural weight. The rocket components considered are ring stiffened truncated cones and cylinders. The applied loading is static, and can consist of any combination of internal or external pressure, axial force, bending moment, and torque. Stress margins are calculated by means of simple closed form strength of material type equations. Stability margins are determined by approximate, orthotropic-shell, closed-form equations. A modified form of Powell's method, in conjunction with a modified form of the external penalty method, is used to determine the minimum weight of the structure subject to stress and stability margin constraints, as well as user input constraints on the structural dimensions. The graphical interface guides the user through the required data prompts, explains program options and graphically displays results for easy interpretation.

Rule, William K.↗

Three-dimensional elastic stress and displacement analysis of finite geometry solids containing cracks

The line method of analysis is applied to the Navier-Cauchy equations of elastic equilibrium to calculate the displacement fields in finite geometry bars containing central, surface, and double-edge cracks under extensionally applied uniform loading. The application of this method to these equations leads to coupled sets of simultaneous ordinary differential equations whose solutions are obtained along sets of lines in a discretized region. Normal stresses and the stress intensity factor variation along the crack periphery are calculated using the obtained displacement field. The reported results demonstrate the usefulness of this method in calculating stress intensity factors for commonly encountered crack geometries in finite solids.

Kring, J.↗

Three-dimensional elastic stress and displacement analysis of finite geometry solids containing cracks

The line method of analysis is applied to the Navier-Cauchy equations of elastic equilibrium to calculate the displacement fields in finite geometry bars containing central, surface, and double-edge cracks under extensionally applied uniform loading. The application of this method to these equations leads to coupled sets of simultaneous ordinary differential equations whose solutions are obtained along sets of lines in a discretized region. Normal stresses and the stress intensity factor variation along the crack periphery are calculated using the obtained displacement field. The reported results demonstrate the usefulness of this method in calculating stress intensity factors for commonly encountered crack geometries in finite solids.

Kring, J.↗

Effect of element size on the solution accuracies of finite-element heat transfer and thermal stress analyses of space shuttle orbiter

The effect of element size on the solution accuracies of finite-element heat transfer and thermal stress analyses of space shuttle orbiter was investigated. Several structural performance and resizing (SPAR) thermal models and NASA structural analysis (NASTRAN) structural models were set up for the orbiter wing midspan bay 3. The thermal model was found to be the one that determines the limit of finite-element fineness because of the limitation of computational core space required for the radiation view factor calculations. The thermal stresses were found to be extremely sensitive to a slight variation of structural temperature distributions. The minimum degree of element fineness required for the thermal model to yield reasonably accurate solutions was established. The radiation view factor computation time was found to be insignificant compared with the total computer time required for the SPAR transient heat transfer analysis.

Ko, William L.↗

Numerical investigation of turbulent channel flow

Fully developed turbulent channel flow was simulated numerically at Reynolds number 13800, based on centerline velocity and channel halt width. The large-scale flow field was obtained by directly integrating the filtered, three dimensional, time dependent, Navier-Stokes equations. The small-scale field motions were simulated through an eddy viscosity model. The calculations were carried out on the ILLIAC IV computer with up to 516,096 grid points. The computed flow field was used to study the statistical properties of the flow as well as its time dependent features. The agreement of the computed mean velocity profile, turbulence statistics, and detailed flow structures with experimental data is good. The resolvable portion of the statistical correlations appearing in the Reynolds stress equations are calculated. Particular attention is given to the examination of the flow structure in the vicinity of the wall.

Moin, P.↗

Analysis of surface cracks in finite plates under tension or bending loads

Stress-intensity factors calculated with a three-dimensional, finite-element analysis for shallow and deep semielliptical surface cracks in finite elastic isotropic plates subjected to tension or bending loads are presented. A wide range of configuration parameters was investigated. The ratio of crack depth to plate thickness ranged from 0.2 to 0.8 and the ratio of crack depth to crack length ranged from 0.2 to 2.0. The effects of plate width on stress-intensity variations along the crack front was also investigated. A wide-range equation for stress-intensity factors along the crack front as a function of crack depth, crack length, plate thickness, and plate width was developed for tension and bending loads. The equation was used to predict patterns of surface-crack growth under tension or bending fatigue loads. A modified form of the equation was also used to correlate surface-crack fracture data for a brittle epoxy material within + or - 10 percent for a wide range of crack shapes and crack sizes.

Newman, J. C., Jr.↗

Enhancement to Non-Contacting Stress Measurement of Blade Vibration Frequency

A system for turbo machinery blade vibration has been developed that combines time-of-arrival sensors for blade vibration amplitude measurement and radar sensors for vibration frequency and mode identification. The enabling technology for this continuous blade monitoring system is the radar sensor, which provides a continuous time series of blade displacement over a portion of a revolution. This allows the data reduction algorithms to directly calculate the blade vibration frequency and to correctly identify the active modes of vibration. The work in this project represents a significant enhancement in the mode identification and stress calculation accuracy in non-contacting stress measurement system (NSMS) technology when compared to time-of-arrival measurements alone.

Platt, Michael↗

Stress wave propagation in a composite beam subjected to transverse impact.

Composite materials, particularly fiber reinforced plastic composites, have been extensively utilized in many military and industrial applications. As an important structural component in these applications, the composites are often subjected to external impact loading. It is desirable to understand the mechanical response of the composites under impact loading for performance evaluation in the applications. Even though many material models for the composites have been developed, experimental investigation is still needed to validate and verify the models. It is essential to investigate the intrinsic material response. However, it becomes more applicable to determine the structural response of composites, such as a composite beam. The composites are usually subjected to out-of-plane loading in applications. When a composite beam is subjected to a sudden transverse impact, two different kinds of stress waves, longitudinal and transverse waves, are generated and propagate in the beam. The longitudinal stress wave propagates through the thickness direction; whereas, the propagation of the transverse stress wave is in-plane directions. The longitudinal stress wave speed is usually considered as a material constant determined by the material density and Young's modulus, regardless of the loading rate. By contrast, the transverse wave speed is related to structural parameters. In ballistic mechanics, the transverse wave plays a key role to absorb external impact energy [1]. The faster the transverse wave speed, the more impact energy dissipated. Since the transverse wave speed is not a material constant, it is not possible to be calculated from stress-wave theory. One can place several transducers to track the transverse wave propagation. An alternative but more efficient method is to apply digital image correlation (DIC) to visualize the transverse wave propagation. In this study, we applied three-pointbending (TPB) technique to Kolsky compression bar to facilitate dynamic transverse loading on a glass fiber/epoxy composite beam. The high-speed DIC technique was employed to study the transverse wave propagation.

36 MATERIALS SCIENCE↗

Comparative modeling of the disregistry and Peierls stress for dissociated edge and screw dislocations in Al

Many elementary deformation processes in metals involve the motion of dislocations. The planes of glide and specific processes dislocations prefer depend heavily on their atomic core structures. Atomistic simulations are desirable for dislocation modeling but their application to even sub-micron scale problems is in general computationally costly. Accordingly, continuum-based approaches, such as the phase-field microelasticity, phase-field dislocation dynamics (PFDD), generalized Peierls–Nabarro (GPN) models, and the concurrent atomistic–continuum (CAC) method, have attracted increasing attention in the field of dislocation modeling because they well represent both short-range cores interactions and long-range stress fields of dislocations. To better understand their similarities and differences, it is useful to compare these methods in the context of benchmark simulations and predictions. In this paper, we apply the CAC method and different PFDD variants – one of them is equivalent to a GPN model – to simulate an extended (i.e., dissociated) dislocation in Al with initially pure edge or pure screw character in terms of the disregistry. CAC and discrete forms of PFDD are also employed to calculate the Peierls stress. By conducting comprehensive convergence studies, we quantify the dependence of these measures on time/grid resolution and simulation cell size. Several important but often overlooked differences between PFDD/GPN variants are clarified. In conclusion, our work sheds light on the advantages and limitations of each method, as well as the path towards enabling them to effectively model complex dislocation processes at larger length scales.

36 MATERIALS SCIENCE↗

Stress-intensity factors for two symmetric corner cracks

This paper presents stress-intensity factors, calculated by a three-dimensional finite-element analysis, for shallow or deep quarter-elliptical corner cracks at the edge of a hole in a finite-thickness plate. The plate was subjected to remote uniform tension, remote bending, or simulated pin loading in the hole; a wide range of configuration parameters was investigated. To verify the accuracy of the three-dimensional finite-element models employed, convergence was studied by varying the numbers of degrees of freedom. The stress-intensity factor variations along the crack front are compared with solutions from the literature.

Raju, I. S.↗

Fatigue Analysis of Notched Laminates: A Time-Efficient Macro-Mechanical Approach

A coupled transversely isotropic deformation and damage fatigue model is implemented within the finite element method and was utilized along with a static progressive damage model to predict the fatigue life, stiffness degradation as a function of number of cycles, and post-fatigue tension and compression response of notched, multidirectional laminates. Initially, the material parameters for the fatigue model were obtained utilizing micromechanics simulations and the provided [0], [90] and [plus or minus 45] experimental composite laminate S-N (stress-cycle) data. Within the fatigue damage model, the transverse and shear properties of the plies were degraded with an isotropic scalar damage variable. The damage in the longitudinal (fiber) ply direction was suppressed, and only the strength of the fiber was degraded as a function of fatigue cycles. A maximum strain criterion was used to capture the failure in each element, and once this criterion was satisfied, the longitudinal stiffness of the element was decreased by a factor of 10 (sup 4). The resulting, degraded properties were then used to calculate the new stress state. This procedure was repeated until final failure of the composite laminate was achieved or a specified number of cycles reached. For post-fatigue tension and compression behavior, four internal state variables were used to control the damage and failure. The predictive capability of the above-mentioned approach was assessed by performing blind predictions of the notched multidirectional IM7/977-3 composite laminates response under fatigue and post-fatigue tensile and compressive loading, followed by a recalibration phase. Although three different multidirectional laminates were analyzed in the course of this study, only detailed results (i.e., stiffness degradation and post-fatigue stress-train curves as well as damage evolution states for a single laminate ([30/60/90/minus 30/minus 60] (sub 2s)) are discussed in detail here.

Composite Fatigue analysis↗

Comparison of residual stresses in Inconel 718 simple parts made by electron beam melting and direct laser metal sintering

Residual stress profiles were mapped using neutron diffraction in two simple prism builds of Inconel 718: one fabricated with electron beam melting and the other with direct laser sintering. Spatially indexed stress-free cubes were obtained by EDM sectioning equivalent prisms of similar shape. The (311) interplanar spacing examined for the EDM sectioned sample was compared to the interplanar spacings calculated to fulfill force and moment balance. We have shown that Applying force and moment balance is a necessary supplement to the measurements for the stress-free cubes with respect to accurate stress calculations in additively manufactured components. Furthermore, our work has shown that residual stresses in electron beam melting parts are much smaller than that of direct laser metal sintering parts.

36 MATERIALS SCIENCE↗

The Lagrangian multiplier method of finding upper and lower limits to critical stresses of clamped plates

The theory of Lagrangian multipliers is applied to the problem of finding both upper and lower limits to the true compressive buckling stress of a clamped rectangular plate. The upper and lower limits thus bracket the true stress, which cannot be exactly found by the differential-equation approach. The procedure for obtaining the upper limit, which is believed to be new, presents certain advantages over the classical Rayleigh-Ritz method of finding upper limits. The theory of the lower-limit procedure has been given by Trefftz, but, in the present application, the method differs from that of Trefftz in a way that makes it inherently more quickly convergent. It is expected that in other buckling problems and in some vibration problems the Lagrangian multiplier method of finding upper and lower limits may be advantageously applied to the calculation of buckling stresses and natural frequencies.

Budiansky, Bernard↗

Characterization of Thick Tungsten Coating on Cu Alloy Substrate Prepared by Electrodeposition

The W coating with the thickness over 1 mm was obtained by pulse electrodeposition on large CuCrZr alloy in a Na{sub 2}WO{sub 4}–WO{sub 3} molten salt. The composition of this system keeps unchanged with the duration of electrodeposition. The coating’s structure, morphology and contents were investigated by XRD, XPS and SEM. The electrodepostion tungsten coating was compact and without void. The residual stress in surface of W coating was calculated to be a compressive stress with the value of 225 MPa. The W coating comprised an inner tooth-like layer and an outer columnar layer. The bonding strength between W coating and CuCrZr susbtrate was near 60 MPa; the thermal conductivity parallel to the crystal growth direction was measured to be 150.86 W m{sup −1} K{sup −1}.

36 MATERIALS SCIENCE↗