Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Preloaded Composite-Strut/End-Fitting Joint

Proposed structural joint between composite strut and metal end fitting strong and light in weight. Joint configured to distribute stresses fairly uniformly, with little interlaminar stress. Composite-strut/metal-fitting joint built up integrally with strut in layup process. Joint remains tight under reversals of loads and changes in temperature.

Monitor, Dean S.↗

Goertler instability on an airfoil: Comparison of marching solution with experimental observations

Theoretical predictions based on the marching technique are compared with experimental observations on an airfoil with a concave region. Theoretical predictions of the wavelength of the most amplified Goertler vortex are in excellent agreement with the experimental observation for the range of chord Reynolds numbers from 1.0 to 3.67 million. In the convex zone, solutions from the marching technique showed that the initial counter-rotating vortex pairs lift off the surface and dissipate while another layer of vortex pairs of opposite rotation develops near the surface. This confirms the experimentally observed double peaked streamwise velocity perturbations. Furthermore, the streamwise velocity perturbations which dominate spanwise variation in the surface shear stress distribution shift by half a wavelength in the convex region. The experimental flow visualization photographs clearly confirm this phenomena.

Kalburgi, Vijay↗

Investigation of turbulent flow in highly curved ducts with application to turbomachinery components

Numerical predictions were performed using a semi-elliptic calculation procedure for the case of turbulent flow in passage through a 90 deg bend of square cross section. Two versions of the isotropic turbulent viscosity two equation k-epsilon model were used. The first, the wall function model (WFM), employs the logarithmic law-of-the-wall relation and the notion of equilibrium flow to set all the necessary boundary conditions at the first grid point adjacent to a solid wall. The second model, the Van Driest model (VDM), employs Prandtl's original mixing length formulation, in conjunction with Van Driest's semi-empirical relation for the mixing length, to calculate the turbulent viscosity in the near wall regions of the flow. In this case, boundary conditions for k and epsilon, required to calculate these quantities in the core of the flow, are obtained by matching the mixing length and Reynolds number model formulations in an overlapping region of the flow near the walls. In both cases the results obtained show an improvement over earlier calculations using an elliptic numerical procedure. This is attributed to the finer grids possible in the present work. Of the two models, the VDM formulation shows better overall conformity with the mean flow measurements. Neither model reproduces well the details of the stress distribution as a result of the implied isotropic turbulent viscosity.

Humphrey, J. A. C.↗

Interlaminar shear stress effects on the postbuckling response of graphite-epoxy panels

The influence of shear flexibility on overall postbuckling response was assessed, and transverse shear stress distributions in relation to panel failure were examined. Nonlinear postbuckling results are obtained for finite element models based on classical laminated plate theory and first-order shear deformation theory. Good correlation between test and analysis is obtained. The results presented analytically substantiate the experimentally observed failure mode.

Engelstad, S. P.↗

Generalized Transition Finite-Boundary Elements for high speed flight structures

A new class of 'Generalized Transition Finite-Boundary Elements' formulation is presented to predict temperature and/or stress distribution of flight structures at high speeds. A tweleve-noded three-dimensional transition element and a variable degree of freedom eight-noded element are formulated. These elements are incorporated into the formulation of the heat transfer and structural analysis problems by utilizing a newly introduced 'material approximation functions' concept. Results obtained from limited examples compared with the solutions from analytical and other finite element analysis solution. Numerical examples presented illustrate the effectiveness of these elements.

Sarigul-Klijn, Nesrin↗

Interlaminar shear stress effects on the postbuckling response of graphite-epoxy panels

The objectives of the study are to assess the influence of shear flexibility on overall postbuckling response, and to examine transverse shear stress distributions in relation to panel failure. Nonlinear postbuckling results are obtained for finite element models based on classical laminated plate theory and first-order shear deformation theory. Good correlation between test and analysis is obtained. The results presented in this paper analytically substantiate the experimentally observed failure mode.

Engelstad, S. P.↗

Damage prediction in cross-plied curved composite laminates

Analytical and experimental work is detailed which is required to predict delamination onset and growth in a curved cross plied composite laminate subjected to static and fatigue loads. The composite used was AS4/3501/6, graphite/epoxy. Analytically, a closed form stress analysis and 2-D and 3-D finite element analyses were conducted to determine the stress distribution in an undamaged curved laminate. The finite element analysis was also used to determine values of strain energy release rate at a delamination emanating from a matrix crack in a 90 deg ply. Experimentally, transverse tensile strength and fatigue life were determined from flat 90 deg coupons. The interlaminar tensile strength and fatigue life were determined from double cantilevered beam specimens. Cross plied curved laminates were tested statically and in fatigue to give a comparison to the analytical predictions. A comparison of the fracture mechanics life prediction technique and the strength based prediction technique is given.

Martin, Roderick H.↗

Analysis of laminated composite shells under internal pressure

A closed form solution is presented that predicts the response of filament wound composite shells subjected to internal pressure. The material of the shell is assumed to be general cylindrically anisotropic. Based on the theory of cylindrical anisotropic elasticity coupled differential equations are developed using Lekhnitskii's stress function approach. Two composite systems, graphite/epoxy and glass/epoxy, are selected to demonstrate the influence of degree of material anisotropy and fiber orientations on the axial and induced twisting deformation. Detailed stress distributions of (45) off-axis unidirectional and (45/-45)s symmetric angle-ply fiber-reinforced laminated shells are shown to illustrate the effect of radius-to-thickness ratio and stacking sequence.

Yuan, F. G.↗

The effect of bleed configuration on shock/boundary layer interactions

The flow field characteristics are simulated numerically in an oblique shock wave/laminar boundary layer interaction for three different bleed configurations. The numerical solution for the flow field is obtained for the strong conservation-law form of the two-dimensional compressible Navier-Stokes equations using an implicit scheme. The computations model the flow in the interaction region and inside the bleed slot for an impinging oblique shock of sufficient strength to cause boundary layer separation on a flat plate boundary layer. The computed results are presented for a normal bleed slot at three different locations, upstream, across and downstream of the shock impingement point. The detailed flow characteristics in the interaction zone and inside the bleed slot are compared for the three cases. The resulting surface pressure and shear stress distributions are also compared for the three bleed cases and for the shock wave boundary layer interaction without bleed.

Hamed, A.↗

Laser interferometer/Preston tube skin-friction comparison in shock/boundary-layer interaction

An evaluation is conducted of the accuracy of the 'Preston tube' surface pitot-pressure skin friction measurement method relative to the already proven laser interferometer skin-friction meter in a swept shock wave/turbulent boundary-layer interaction. The Preston tube was used to estimate the total shear-stress distribution in a fin-generated swept shock-wave/turbulent boundary-layer interaction. The Keener-Hopkins calibration method using the isentropic relation to calculate the Preston-tube Mach number produces the best results.

Kim, K.-S.↗

Reynolds shear stress and heat flux calculations in a fully developed turbulent duct flow

The use of a modified form of the Van Driest mixing length for a fully developed turbulent channel flow leads to mean velocity and Reynolds stress distributions that are in close agreement with data obtained either from experiments or direct numerical simulations. The calculations are then extended to a nonisothermal flow by assuming a constant turbulent Prandtl number, the value of which depends on the molecular Prandtl number. Calculated distributions of mean temperature and lateral heat flux are in reasonable agreement with the simulations. The extension of the calculations to higher Reynolds numbers provides some idea of the Reynolds number required for scaling on wall variables to apply in the inner region of the flow.

Antonia, R. A.↗

Numerical analysis of the Iosipescu specimen for composite materials

A finite element analysis of the Iosipescu shear tests for unidirectional and cross-ply composites is presented. It is shown that an iterative analysis procedure must be used to model the fixture-specimen kinematics. The correction factors which are needed to compensate for the nonuniformity of stress distribution in calculating shear modulus are shown to be dependent on the material orthotropic ratio and the finite element loading models. Test section strain distributions representative of typical graphite-epoxy specimens are also presented.

Ho, H.↗

Modeling of composite beams and plates for static and dynamic analysis

A rigorous theory and the corresponding computational algorithms were developed for through-the-thickness analysis of composite plates. This type of analysis is needed in order to find the elastic stiffness constants of a plate. Additionally, the analysis is used to post-process the resulting plate solution in order to find approximate three-dimensional displacement, strain, and stress distributions throughout the plate. It was decided that the variational-asymptotical method (VAM) would serve as a suitable framework in which to solve these types of problems. Work during this reporting period has progressed along two lines: (1) further evaluation of neo-classical plate theory (NCPT) as applied to shear-coupled laminates; and (2) continued modeling of plates with nonuniform thickness.

Hodges, Dewey H.↗

Sensitivity of the structure of untripped mixing layers to small changes in initial conditions

An experimental study was conducted concerning the influence of small changes in initial conditions on the near- and far-field evolution of the three-dimensional structure of a plan mixing layer. A two-stream mixing layer with a velocity ratio of 0.6 was generated with the initial boundary layers on the splitter plate laminar and was nominally two-dimensional. The initial conditions were changed slightly by interchanging the high- and low-speed sides of the wind tunnel, while maintaining the same velocities, and hence velocity ratio. This resulted in small changes in the initial boundary layer properties, and the perturbations present in the boundary layers were interchanged between the high- and low-speed sides for the two cases. The results indicate that, even with this relatively minor change in initial conditions, the near-field regions of the two cases differ significantly. The peak Reynolds stress levels in the near-field differ by up to 100 percent, and this is attributed to a difference in the location of the initial spanwise vortex roll-up. In addition, the positions and shapes of the individual streamwise vortical structures differ for the two cases, although the overall structures differ for the two cases, although the overall qualitative description of these structures is comparable. The subsequent reorganization and decay of the streamwise vortical structures is very similar for the two cases. As a result, in the far field, both mixing layers achieve similar structure, yielding comparable growth rates, Reynolds stress, distribution, and spectral content.

Plesniak, M. W.↗

Nonlinear shell analysis of the Space Shuttle Solid Rocket Boosters

A variety of structural analyses have been performed on the Solid Rocket Boosters (SRB's) to provide information that would contribute to the understanding of the failure which destroyed the Space Shuttle Challenger. This paper describes nonlinear shell analyses that were performed to characterize the behavior of an overall SRB structure and a segment of the SRB in the vicinity of the External Tank Attachment (ETA) ring. Shell finite element models were used that would accurately reflect the global load transfer in an SRB in a manner such that nonlinear shell collapse and ovalization could be assessed. The purpose of these analyses was to calculate the overall deflection and stress distributions for these SRB models when subjected to mechanical loads corresponding to critical times during the launch sequence. Static analyses of these SRB models were performed using a 'snapshot picture' of the loads. Analytical results obtained using these models show no evidence of nonlinear shell collapse for the pre-liftoff loading cases considered.

Knight, N. F., Jr.↗

Deformation and stress response of composite laminated shells under internal pressure

This paper presents a theoretical study of the response of filament wound composite shells under internal pressure. Each layer of the material is generally cylindrically anisotropic. By using cylindrically anisotropic elasticity field equations and Lekhnitskii's stress functions, a system of sixth-order ordinary differential equations is obtained. The general expressions for the stresses and displacements in the laminated composite shells under internal pressure are discussed. Two composite systems, graphite/epoxy and glass/epoxy, are selected to demonstrate the influence of degree of material anisotropy and fiber orientations on the axial and induced twisting deformation. Stress distributions of (45/-45)s symmetric angle-ply fiber-reinforced laminated shells are shown to illustrate the effect of radius-to-thickness ratio.

Yuan, F. G.↗

Analysis for delamination initiation in postbuckled dropped-ply laminates

The compression strength of dropped-ply, graphite-epoxy laminated plates for the delamination mode of failure is studied by analysis and corroborated with experiments. The nonlinear response of the test specimens is modeled by a geometrically nonlinear finite element analysis. The methodology for predicting delamination is based on a quadratic interlaminar stress criterion evaluated at a characteristic distance from the ply drop-off. The compression strength of specimens exhibiting a linear response is greater than the compression strength of specimens with the same layup exhibiting a geometrically nonlinear response. The analyses for both linear and nonlinear response show that severe interlaminar stress gradients occur in the interfaces at the drop-off because of the thickness/stiffness discontinuity. However, these interlaminar stress distributions are altered in the geometrically nonlinear response such that, with increasing load, their growth at the center of the laminate is retarded while their growth near the unloaded supported edge is increased.

Davila, Carlos G.↗

Application of the variational-asymptotical method to composite plates

A method is developed for the 3D analysis of laminated plate deformation which is an extension of a variational-asymptotical method by Atilgan and Hodges (1991). Both methods are based on the treatment of plate deformation by splitting the 3D analysis into linear through-the-thickness analysis and 2D plate analysis. Whereas the first technique tackles transverse shear deformation in the second asymptotical approximation, the present method simplifies its treatment and restricts it to the first approximation. Both analytical techniques are applied to the linear cylindrical bending problem, and the strain and stress distributions are derived and compared with those of the exact solution. The present theory provides more accurate results than those of the classical laminated-plate theory for the transverse displacement of 2-, 3-, and 4-layer cross-ply laminated plates. The method can give reliable estimates of the in-plane strain and displacement distributions.

Hodges, Dewey H.↗