Search NASA⌕ Search

SEARCH · Search NASA

Results for “Structured Light Scanning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Fast ionic conduction achieved through the design and synthesis of ceramic heterointerfaces

Lithium (Li) chloride and iron oxychloride (FeOCl), typically nonconductive, were combined to form a [Li 1+δ Cl] δ+ /[FeOCl] δ- heterointerface composite material (LFH), achieving ionic conductivities of >1 mS cm -1 . Analysis techniques (scanning transmission electron microscopy [STEM] and electron energy-loss spectroscopy [EELS]) indicated that the microstructure of LFH consisted of an amorphous LiCl-based shell surrounding a crystalline FeOCl-based core. Electrochemical measurements alongside solid-state 6,7 Li nuclear magnetic resonance (NMR) and molecular dynamic simulations revealed Li+ as the sole conductive species, with a diffusion barrier of ~0.25 eV. X-ray photoelectron spectroscopy (XPS) and X-ray absorption fine structure (XAFS) results further supported interstitial Li + diffusion at the heterointerface and within the LiCl phase, made possible by the heterointerface. Despite susceptibility to electronic conductivity, iron’s defects and multivalency (Fe³⁺, Fe²⁺) enable the Fe–O–Cl framework to accept Cl - , facilitating Li⁺ ionic conduction. Finally, a prototype solid-state cell (showing 97% Coulombic efficiency) demonstrated the viability of this heterointerface design for applications in energy storage.

36 MATERIALS SCIENCE↗

R and DE Robotic Sensor Intern Team: Sensor Suite Mock Up Testing

Assess sensor suite performance: - Mounted on crawler typical to what would be used in tunnel; - In test bed simulating the tunnel environment. The SuperDroid fiber tethered LT-F crawler is a general-purpose surveillance robot that our team has refurbished as a testing platform for the sensor suite. This crawler was selected because its dimensions are similar to the actual crawler that will be deployed in the field. Crawler preparation included: - Communicating with vendor to resolve software and platform issues; - Configuring a laptop with the crawler control software; - Reconfiguration of communication protocol between computer and crawler; - Resolution of control board checksum errors; - Installation of a mounting fixture on the base; - In progress: addition of lighting needed for total darkness. A solution for hosting the selected sensors onto a single unit that could function standalone or be mounted on the crawler was needed. Sensor mount requirements included: - Host Lidar, panospheric cameras and IMU sensors; - Cable management for rotating Lidar; - House on-board crawler computer; - Method for affixing to crawler; - Robust and vibration proof. The Lidar sensor required a sturdy mount that ensured the axis of rotation be centered with the LiDAR's desired laser path and included a slender profile in order to not block the scanning FOV. The mounting plate holds two 180-degree cameras on either side and the servo on the center. The servo mount is located so the axis of rotation is in the center of the plate. The mount features a set of guides that hold the wires and ensure they wrap around the spool area properly. The sensor box design features thick walls for added strength, holes for mounting the sensor suite to the crawler, notches on the bottom for the different components and holes for cable routing and management. The sensor mounts were designed using CREO and printed in the R and DE Additive Manufacturing Lab. To test the performance of the sensor suite for our application it was desired to design and build a test bed simulating the H-Canyon tunnel environment. Requirements included: - Dimensions similar to the tunnel; - Wall surfaces simulating the eroded tunnel walls; - Complete darkness; - Even and uneven crawler path; - Ability to change the tunnel width to simulate erosion. The HCAEX tunnel changes in height and includes several bends ranging from approximately 30 to 80 degrees, for that reason a test bed capable of easily being changed was needed. The final design includes two sections that can be connected to provide a 16' tunnel or placed at an angle to create a tunnel bend. The test bed features caster wheels for easy movement and has a sliding inner wall that enables tunnel width to be controlled. In order to simulate the tunnel walls without adding a lot of weight to the test bed, sheets of faux stone are to be used on the inner walls. To create a completely dark tunnel, 100% black-out film will be draped over the tunnel structure. Carpet remnants in the lab will enable folds to be introduced in the floor to generate uneven surface data.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Three Dimensional Mapping of Nicle Oxidation States Using Full Field Xray Absorption Near Edge Structure Nanotomography

The reduction-oxidation cycling of the nickel-based oxides in composite solid oxide fuel cells and battery electrodes is directly related to cell performance. A greater understanding of nickel redox mechanisms at the microstructural level can be achieved in part using transmission x-ray microscopy (TXM) to explore material oxidation states. X-ray nanotomography combined with x-ray absorption near edge structure (XANES) spectroscopy has been applied to study samples containing distinct regions of nickel and nickel oxide (NiO) compositions. Digitally processed images obtained using TXM demonstrate the three-dimensional chemical mapping and microstructural distribution capabilities of full-field XANES nanotomography.

30 DIRECT ENERGY CONVERSION↗

Selective Oxidation and Cr Segregation in High-Entropy Oxide Thin Films

High-entropy oxides (HEOs) offer exceptional compositional flexibility and structural stability, making them promising materials for energy and catalytic applications. Here, in this study, we investigate Sr doping effects on B-site cation oxidation states, local composition, and structure in epitaxial La 1–x Sr x (Cr 0.2 Mn 0.2 Fe 0.2 Co 0.2 Ni 0.2 )O 3 thin films. X-ray spectroscopies reveal that Sr doping preferentially promotes Cr oxidation from Cr 3+ to Cr 6+ , partially oxidizes Co and Ni, while leaving Mn 4+ and Fe 3+ unchanged. Atomic-resolution scanning transmission electron microscopy with energy-dispersive X-ray spectroscopy shows pronounced Cr segregation, with depletion at the interface and enrichment at the surface, along with partial amorphization in heavily Sr-doped samples. This segregation is likely driven by oxidation-induced migration of smaller, high-valence Cr cations during growth. These findings highlight the critical interplay between charge compensation, local strain, and compositional fluctuations in HEOs, indicating that precise control over growth conditions is critical for tuning their surface composition and electronic structure toward more robust electrocatalyst design.

36 MATERIALS SCIENCE↗

Voltage and temperature effects on low cobalt lithium-ion battery cathode degradation

Degradation of low cobalt lithium-ion cathodes was tested using a full factorial combination of upper cut-off voltage (4.0 V and 4.3 V vs. Li/Li + ) and operating temperature (25 °C and 60 °C). Half-cell batteries were analyzed with electrochemical and microstructural characterization methods. Electrochemical performance was assessed with galvanostatic cycling, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS) supported by distribution of relaxation times (DRT) analysis. Electrode microstructure was characterized with scanning electron microscopy (SEM), X-ray diffraction (XRD), and X-ray absorption near edge structure (XANES) imaging. Higher cut-off voltage cycling shows presence of NiO x formation, a low diffusivity rock-salt phase, in both CV and XRD data. XRD patterns confirmed that the rock-salt phase was beginning to form at the low cut-off voltage at high temperature, but in much lower intensity than at the high cut-off voltage. Higher temperature accelerates degradation processes at both voltages. Degradation factors at high temperature include NiO x formation, cathode material dissolution, and electrolyte decomposition. SEM analysis suggests that supporting phases may isolate and disconnect active material particles reducing capacity retention and battery life cycle. DRT analysis and XANES imaging show that both high temperature samples revealed a NiO x phase based on an increased diffusive impedance and a visible shift in the XANES spectra. The low cut-off voltage, high temperature sample showed a split peak and shift to lower energies indicating early formation of the NiO x phase. The diffusive impedance, which hinders intercalation and deintercalation, is driven by the formation of the NiO x phase. While primarily driven by cut-off voltage, elevated temperature also contributes to this degradation mechanism.

electrochemical impedance spectroscopy↗

A general framework and review of scatter correction methods in x-ray cone-beam computerized tomography. Part 1: Scatter compensation approaches

Since scattered radiation in cone-beam volume CT implies severe degradation of CT images by quantification errors, artifacts, and noise increase, scatter suppression is one of the main issues related to image quality in CBCT imaging. The aim of this review is to structurize the variety of scatter suppression methods, to analyze the common structure, and to develop a general framework for scatter correction procedures. In general, scatter suppression combines hardware techniques of scatter rejection and software methods of scatter correction. The authors emphasize that scatter correction procedures consist of the main components scatter estimation (by measurement or mathematical modeling) and scatter compensation (deterministic or statistical methods). The framework comprises most scatter correction approaches and its validity also goes beyond transmission CT. Before the advent of cone-beam CT, a lot of papers on scatter correction approaches in x-ray radiography, mammography, emission tomography, and in Megavolt CT had been published. The opportunity to avail from research in those other fields of medical imaging has not yet been sufficiently exploited. Therefore additional references are included when ever it seems pertinent. Scatter estimation and scatter compensation are typically intertwined in iterative procedures. It makes sense to recognize iterative approaches in the light of the concept of self-consistency. The importance of incorporating scatter compensation approaches into a statistical framework for noise minimization has to be underscored. Signal and noise propagation analysis is presented. A main result is the preservation of differential-signal-to-noise-ratio (dSNR) in CT projection data by ideal scatter correction. The objective of scatter compensation methods is the restoration of quantitative accuracy and a balance between low-contrast restoration and noise reduction. In a synopsis section, the different deterministic and statistical methods are discussed with respect to their properties and applications. The current paper is focused on scatter compensation algorithms. The multitude of scatter estimation models will be dealt with in a separate paper.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Topological excitonic insulator with tunable momentum order

Correlated topological materials often maintain a delicate balance among physical symmetries. Many topological orders are symmetry protected, whereas most correlated phenomena arise from spontaneous symmetry breaking. Cases where symmetry breaking induces a non-trivial topological phase are rare. Here we demonstrate the presence of two such phases in Ta 2 Pd 3 Te 5 , where Coulomb interactions form excitons that condense below 100 K, one with zero and the other with finite momentum. We observed a full spectral bulk gap, which stems from exciton condensation. This topological excitonic insulator state spontaneously breaks mirror symmetries but involves a weak structural coupling. Scanning tunnelling microscopy shows gapless boundary modes in the bulk insulating phase. Their magnetic field response, together with theoretical modelling, indicates a topological origin. These observations establish Ta 2 Pd 3 Te 5 as a topological excitonic insulator in a three-dimensional crystal. Finally, our results manifest a unique sequence of topological exciton condensations in a bulk crystal, offering exciting opportunities to study critical behaviour and excitations.

36 MATERIALS SCIENCE↗

Atom probe study of grain boundary segregation in technically pure molybdenum

Molybdenum, a metal with excellent physical, chemical and high-temperature properties, is an interesting material for applications in lighting-technology, high performance electronics, high temperature furnace construction and coating technology. However, its applicability as a structural material is limited because of the poor oxidation resistance at high temperatures and a brittle-to-ductile transition around room temperature, which is influenced by the grain size and the content of interstitial impurities at the grain boundaries. Due to the progress of the powder metallurgical production during the last decades, the amount of impurities in the current quality of molybdenum has become so small that surface sensitive techniques are not applicable anymore. Therefore, the atom probe, which allows the detection of small amounts of impurities as well as their location, seems to be a more suitable technique. However, a site-specific specimen preparation procedure for grain boundaries in refractory metals with a dual focused ion beam/scanning electron microscope is still required. The present investigation describes the development and successful application of such a site-specific preparation technique for grain boundaries in molybdenum, which is significantly improved by a combination with transmission electron microscopy. This complimentary technique helps to improve the visibility of grain boundaries during the last preparation steps and to evidence the presence of grain and subgrain boundaries without segregants in atom probe specimens. Furthermore, in industrially processed and recrystallized molybdenum sheets grain boundary segregation of oxygen, nitrogen and potassium is successfully detected close to segregated regions which are believed to be former sinter pores. - Highlights: • First study of grain boundary segregation in molybdenum by atom probe • Site-specific preparation technique by FIB and TEM successfully developed • Grain boundary segregation of oxygen, nitrogen and potassium found • Segregation in former sinter-pores detected • Presence of grain boundaries without segregation evidenced.

36 MATERIALS SCIENCE↗

Pt Particles on a Dynamic TiO 2 Support in Near-Ambient Conditions−Disentangling Size, Pressure, and Support Effects

Platinum particles on reducible oxides are known to form complex and highly dynamic catalyst systems at elevated pressures and temperatures, often adopting active structures that differ from those found at room temperature and under ultrahigh vacuum (UHV). Here, we study the oxidation and structural evolution of subnanometer Pt clusters and nanoparticles supported on rutile TiO 2 (110) across an oxygen pressure range from UHV to 0.1 mbar, using near-ambient pressure X-ray photoelectron spectroscopy (NAP-XPS), scanning tunneling microscopy (STM) under UHV and NAP conditions, and low-energy ion scattering (LEIS). Our results reveal distinct differences in oxidation behavior and thermal stability between Pt nanoparticles and clusters, which are further modulated by the support stoichiometry and oxygen pressure. Small Pt clusters become oxidized even at room temperature but are susceptible to accelerated sintering in 0.1 mbar O 2 at elevated temperatures. In contrast, well-crystallized Pt nanoparticles on near-stoichiometric TiO 2 show weaker oxidation. On a reduced, defective TiO 2 support, Pt instead quickly becomes deeply buried by new titania layers, which are formed during support reoxidation. This process appears to result primarily from interactions of the support with the gas phase, unlike the classical, selflimited encapsulation that is induced by the strong metal−support interaction (SMSI). Finally, we address the full complexity of real catalysts in a direct side-by-side comparison of the single-crystalline model system with a Pt-loaded TiO 2 powder catalyst (P25). We conclude that the stoichiometry of the model supports must be carefully chosen and controlled to accurately reproduce the expected state of powder supports during redox reactions.

metal nanoparticles↗

Enhanced red luminescence quantum yield from Gd3+/Eu3+: CaLa2ZnO5 phosphor spheres for photonic applications

Highlights: • Ravishing red emission is observed from Gd{sup 3+}/Eu{sup 3+}: CaLa{sub 2}ZnO{sub 5} phosphor spheres. • Red emission of Eu{sup 3+} was significantly enhanced by co-doping with Gd{sup 3+}. • Effective sensitization of Gd{sup 3+} ions and enhanced quantum yield have been elucidated. • Energy transfer from Gd{sup 3+} to Eu{sup 3+} was demonstrated by several fluorescence dynamics. • CIE coordinates are very close to National Television Standard Committee (NTSC). - Abstract: Novel bright red emission was obtained from co-doped Gd{sup 3+}/Eu{sup 3+}: CaLa{sub 2}ZnO{sub 5} (CLZO) phosphor spheres. We have successfully synthesized co-doped Gd{sup 3+}/Eu{sup 3+}: CLZO phosphor spheres by citrate sol-gel method. Structural and morphological analysis was carried out by XRD and FE-SEM. EDS and XPS studies were employed to analyze the presence of elements and their ionic states respectively. The complex formation studies were carried out by the FTIR spectral study. The photoluminescence spectral profiles confirm the dazzling red emission has been observed at 626 nm ({sup 5}D{sub 0} → {sup 7}F{sub 2}) from the Eu{sup 3+}: CLZO phosphors under the excitation of 467 nm. Upon increasing the Eu{sup 3+} concentration, the photoluminescence performance has also increased remarkably. The optimized concentration of the Eu{sup 3+} was noticed at 12 mol%. Upon co-doping with Gd{sup 3+} ions to Eu{sup 3+}: CLZO phosphors, the red emission pertaining to Eu{sup 3+} was appreciably enhanced through energy transfer from Gd{sup 3+} to Eu{sup 3+} ions. The energy transfer mechanism was substantiated by several fluorescent methods such as lifetime decay dynamics and quantum efficiencies. Commission International de I’Echairage (CIE) 1931 chromaticity coordinates (x–y) calculated for singly doped and co-doped CLZO samples. The CIE coordinates were found to be (0.6644, 0.3355) and (0.6688, 0.3311) respectively, which were good consistent with the standard values of NTSC surprisingly. Correlated color temperature (CCT) value was evaluated for optimised co-doped sample and it was found to be between 2000–5000 K which could be more preferable red component for warm white light applications. The lifetime and quantum efficiency of the optimized co-doped sample have been evaluated as 1.102 ms and 69% respectively. The ravishing red emission of the Gd{sup 3+}/Eu{sup 3+}: CLZO phosphor spheres which suggests that these phosphor materials could be promising candidates for red luminescent optical devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Laboratory-Scale Coal-Derived Graphene Process (Final Report)

The Energy & Environmental Research Center (EERC) conducted a laboratory-scale coal-derived graphene (CDG) project focused on developing a technological process for making graphene from four U.S. domestic coal or coal wastes, including lignite from North Dakota, subbituminous coal from Wyoming, bituminous coal from Utah, and anthracite from Pennsylvania. The project was divided into two performance or budget periods (BPs), with BP1 comprising the up-front laboratory experiments to make graphene materials from coal beginning on May 1, 2020, to April 30, 2022. BP2 was conducted from May 1, 2022, to April 30, 2023, and was focused on analyzing the CDG process economic feasibility and the technical gaps for technological scale-up and commercialization. During this project, a few different coal-derived high-value products have been demonstrated, including graphite, graphene oxide (GO), reduced graphene oxide (rGO), and graphene quantum dots (GQDs). A new graphite microstructure was discovered and named “croissant graphite” because of the exterior morphological and textural resemblance to croissant food items sold in commercial groceries stores. The new graphite structure and the associated preparation from coal or coal waste feedstocks has been the subject of a U.S. patent application. The systematic experimental processes involving coal cleaning, upgrading, and conversion to high-value carbon products culminated into a developed upgraded coal-to-products (UCP) technology that is being pursued for potential fast-track commercialization, if funding is available. It is envisioned that commercialization of the UCP technology would increase consumption of U.S. domestic coals or coal wastes to make environmentally sustainable high-value products for the electronics industry, high-energy-storage applications, and clean energy technologies such as electric vehicle (EV) lithium-ion batteries (LIBs), for which graphite has become a critical mineral commodity. Croissant graphite microstructures, when observed by field emission scanning electron microscopy (FESEM), display wavy surface morphology and often grow from a base that is made of graphitized particles with honeycomb-like layers, which are believed to be graphene layers. While more studies are needed to fully ascertain the mechanisms of the croissant graphite microstructure formation, it is postulated that their growth may begin from curling of the graphene sheets into ribbon-like structures, and continuous growth and densification of the ribbon-like structures forms croissant microstructures. Additional studies are ongoing to evaluate the electrochemical performance of croissant graphite for LIB applications and to determine the experimental conditions necessary to tune on/off croissant formation so that it can be either optimized or suppressed depending on performance evaluation results. In addition to the discovery of croissant graphite, the graphitization process from the four coal ranks in general was successful. X-ray diffraction (XRD) analysis showed that the degree of graphitization (DoG) ranged from 12% to 80% in an early sample set, and further optimization on lignite coal produces a DoG of about 92%, which was spectacular to see as lignite is the lowest-rank coal. Thus, it is expected that the graphitization performance for higher-rank coals will be similar or better when optimized as well. The coal-derived graphite was used to make GO and rGO. Analytical characterization, e.g., by methods such as Raman spectroscopy, XRD, Fourier transform infrared (FTIR) spectroscopy and FESEM, showed that the sequence of converting the coal to graphite, exfoliating it to GO, and then chemically reducing the GO to rGO was successful. Although coal naturally contains aromatic compounds and some relatively small-sized condensed aromatic units, it does not contain graphene sheets. In the UCP process, the aromatic domains in the coals, particularly low-rank coals, are concentrated and condensed further into graphene sheets, which are ordered into a 3D stack during graphitization. The synthesized graphite is then unpacked by methods such as exfoliation to various graphene products. GQDs were synthesized from all four coal types, and their optical properties were demonstrated to be tunable by the coal precursor preprocessing treatments. In all four coal types, enhanced optical properties were observed for the produced GDQs with incremental improvements made to the coal precursors. GQDs produced from raw coal samples displayed lower ultraviolet–visible (UV–Vis) spectroscopy absorbance intensity compared to those obtained from cleaned and upgraded coal residues. The photoluminescence (PL) intensities also varied with pretreatment conditions and with the concentration of GQDs in aqueous solutions. GQDs obtained from anthracite show longer emission wavelengths and can be excited by visible light as opposed to GQDs derived from the other coal ranks. UV fluorescence 3D maps and spectra revealed that the emission wavelength at which the GQDs solutions display the highest intensity was slightly redshifted based on the coal precursor pretreatments. In low-rank coal (lignite and subbituminous) samples, two clusters were observed in the maps for GQDs, which may suggest that there are potentially two types of fluorophores in solution or two main size populations. The ability to tune the properties of GQDs based on processing methods can be exploited to make GQDs for various optical display or optoelectronics applications. The results also highlight the importance of removing coal-borne impurities to improve the quality of the coal precursor for preparation of graphene products. Coal and/or coal wastes preprocessing methods were developed and applied to clean and upgrade the coal precursors prior to graphitization and subsequent conversion to graphene products. The preprocessing methods involve high specific-gravity separations, mineral acid cleaning (no hydrofluoric acid), and subsequent upgrading by reducing the coal-borne heteroatom (nitrogen, sulfur, and oxygen) content using proprietary chemical agents. Analytical characterization revealed that the preprocessing steps were successful, with ash reductions that range from 38% to 80% and residual ash content that was below the 5 wt% initial target. Based on proximate and ultimate analysis, the heteroatom reduction reactions produced upgraded coal residues with the oxygen content reduced by 8% to 24%, with additional reductions in the nitrogen and sulfur contents. An initial assessment of the waste streams from the UCP process shows very small to negligible environmental impact due to CO 2 , NO x , and SO x because most process steps are performed under inert atmosphere with argon. Consequently, reactive oxygen environments that tend to create these species are avoided. The inorganic and potentially hazardous species are released into aqueous waste streams that are easy to handle for proper disposal. The liquid waste streams were found to contain low-level concentrations of rare-earth elements (REEs), which could be concentrated and recovered as value-added by-products. Additionally, the volatile and gaseous fractions from carbonization and heat treatment contain useful organic compounds that can also be recovered as potential valuable by-products. Thus, the UCP technology is considered an environmentally sustainable and promising emerging technology for making high-value products from coal and coal wastes, with potential additional value-added by-products. Analysis of potential markets for the coal-derived carbon products shows a strong demand in both niche market sectors and across a wide variety of other industrial sectors. Graphite is currently considered a critical mineral commodity that has a large and growing demand in the LIB industry for EV applications. Based on data from Fortune Business Insights (2022) and Marketwatch (2023) reports, the average global graphite market is projected to reach about 33 billion by 2028, growing at a compound annual growth rate (CAGR) of about 7%, with much of this growth expected to be in the LIB industry. GO and rGO have strong market potentials in various application areas, such as coatings for anticorrosion, anti-icing, and antimicrobial protection, thermal barriers, wear resistance, sensors, additive manufacturing such as 3D inks, and others. GQDs are the emerging key player in the bioimaging, photovoltaics, and light-emitting diodes (LEDs) applications, with the potential to replace traditional semiconductor quantum dots (SQDs), which are based on metallic systems that are more toxic and more expensive. Biomedical applications of GQDs are becoming more attractive because of low to no toxicity and extremely low cost compared to SQDs. The major challenges for scale-up and commercialization of coal-derived carbon products such as graphene vary from the inherent attributes of graphene itself to reluctance to accept graphene in new manufacturing processes because of the uncertainty of the unknown. The 2D nature of graphene materials with a thickness of one atom presents significant challenges to proper handling/processing, and process scale-up becomes difficult because it requires high-end, expensive equipment, even for routine handling and analysis for quality assurance and control. Pristine graphene can also be extremely difficult to work into other matrices, thus hindering downstream processibility, especially at large scale. Currently, the cost of graphene and graphene products is still high and presents an economic risk that tends to slow down investment in scaling up emerging technologies. The lack of a standard for graphene materials for quality assurance and quality control poses a great challenge not only for the markets but also for commercialization efforts. A first-look economic feasibility analysis of the UCP technology provided valuable information that suggests the UCP process would be feasible, especially when it is scaled to a pilot scale and could be more competitive at the full scale. Graphitization was found to be the most energy-consuming and most capital-intensive step in the overall process. In small laboratory- and bench-scale experiments, labor is a significant contributor to the total process costs. Although these energy, capital, and labor constraints contribute to a higher selling price for the product, a preliminary economic model suggests that the process would be feasible at large scale when the process is fully integrated, optimized, and automated.

01 COAL, LIGNITE, AND PEAT↗

Effect of Heat Treatment on Microstructure and Mechanical Property of 316L Stainless Steel Produced by Laser Powder Bed Fusion

The advanced non-light water reactor designs (Gen IV reactors), including molten salt/ very high temperature/ sodium-cooled and lead-cooled fast reactors, typically operate at higher temperatures and more extreme radiation conditions than light water reactors. An intrinsic part of the deployment and progress of Gen IV reactor designs is selecting the most suitable structural material for a specific application. Additive manufacturing (AM), a fairly new process of making physical, three-dimensional objects from a computer design file, is going to completely change the way of design, build and certify nuclear systems. It offers a range of opportunities to produce complex geometries from existing materials, offers new routes for processing of previously difficult to process materials, allows for design of new high-performance materials, and finally facilitates hybridization of dissimilar materials. This emerging technology has successfully produced cars, wind turbine blade molds and even live cells. It could also open up big opportunities for the nuclear industry to quickly deploy technologies at a fraction of the cost. So far, AM techniques have been preliminarily applied in the field of nuclear reactors, including the classical parts such as the pressure vessel of a small reactor with 508-III steel, the bottom nozzle of a fuel assembly with 304L steel, the fuel cladding with zirconium alloy and the integrated impeller of a pump and the multi-channel valve body with 316L steel [6,7]. The AM applications for operating nuclear reactors started in auxiliary plant components and have slowly migrated to metallic reactors and core components, but many of these are not safety critical components. Although many parts used for nuclear reactors have been fabricated by AM techniques, practical applications in engineering are still a long way off due to the uncertainty factors focused on the processing, material properties, analysis methods and application standards, which feeds the safety and life-cycle of the nuclear reactor. Due to rapid, repeated heating and cooling during production, a high dislocation density was present in the AM material. This microstructure feature is unstable at elevated temperature while high temperature is one of the typical operation environments for nuclear reactors. Thus, it is important to understand the thermal effect on the microstructure of AM material. The objectives of this study are to investigate the effect of heat treatment on the microstructure and mechanical properties of 316L stainless steel produced by laser powder bed fusion additive manufacturing, and to determine an appropriate heat treatment practice that will be applied to the lightweight AM lattice-structured material with the same chemistry. The heat treatment study consisted of annealing the samples at a temperature range of 800 to 1200 oC with a 50 oC increment for different times (1-24 hours), followed by vacuum or air cooling. Microstructural characterization was carried out by Scanning Electron Microscope (SEM). Grain size and crystallographic orientation were investigated by Electron Backscatter Diffraction (EBSD). Vickers hardness tests with a 0.5 kg load were employed to determine the hardness of samples after different heat treatments. After heat treatment, the random crystallographic orientation was preserved, and the volume fraction of high-angle grain boundaries (grain boundary misorientation =15 oC) remained the same. The dislocation density decreased with annealing temperature due to recovery. The fine subgrain structures in the as-printed specimen were quite stable up to 1200 oC. Minimal recrystallization was observed up to 1200 oC. Recrystallization initiated only after 8.5 hours at 1200 oC. The SEM images did not show obvious dependence of microstructure on cooling rate. The hardness of the specimens decreased with increasing annealing temperature as a result of the decrease in dislocation density. It is interesting to note that the AM material showed very similar hardness to the wrought material when annealing at similar temperature, although the microstructures are very different. Annealing at 1050 oC for 1 hour followed by air cooling was selected as the heat treatment procedure for the lattice designed lightweight AM 316L material.

36 MATERIALS SCIENCE↗

Activation of Noble Metals on Metal-Carbide Surfaces: Novel Catalysts for CO Oxidation, Desulfurization and Hydrogenation Reactions

This perspective article focuses on the physical and chemical properties of highly active catalysts for CO oxidation, desulfurization and hydrogenation reactions generated by depositing noble metals on metal-carbide surfaces. To rationalize structure-reactivity relationships for these novel catalysts, well-defined systems are required. High-resolution photoemission, scanning tunneling microscopy (STM) and first-principles periodic density-functional (DF) calculations have been used to study the interaction of metals of Groups 9, 10 and 11 with MC(001) (M = Ti, Zr, V, Mo) surfaces. DF calculations give adsorption energies that range from 2 eV (Cu, Ag, Au) to 6 eV (Co, Rh, Ir). STM images show that Au, Cu, Ni and Pt grow on the carbide substrates forming two-dimensional islands at very low coverage, and three-dimensional islands at medium and large coverages. In many systems, the results of DF calculations point to the preferential formation of admetal-C bonds with significant electronic perturbations in the admetal. TiC(001) and ZrC(001) transfer some electron density to the admetals facilitating bonding of the adatom with electron-acceptor molecules (CO, O{sub 2}, C{sub 2}H{sub 4}, SO{sub 2}, thiophene, etc.). For example, the Cu/TiC(001) and Au/TiC(001) systems are able to cleave both S-O bonds of SO{sub 2} at a temperature as low as 150 K, displaying a reactivity much larger than that of TiC(001) or extended surfaces of bulk copper and gold. At temperatures below 200 K, Au/TiC is able to dissociate O{sub 2} and perform the 2CO + O{sub 2} {yields} 2CO{sub 2} reaction. Furthermore, in spite of the very poor hydrodesulfurization performance of TiC(001) or Au(111), a Au/TiC(001) surface displays an activity for the hydrodesulfurization of thiophene higher than that of conventional Ni/MoS{sub x} catalysts. In general, the Au/TiC system is more chemically active than systems generated by depositing Au nanoparticles on oxide surfaces. Thus, metal carbides are excellent supports for enhancing the chemical reactivity of noble metals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Light Material Interactions in Energy Conversion (Final Report)

The scientific vision of the “Light-Material Interactions in Energy Conversion” Energy Frontier Research Center (LMI-EFRC) is embodied in our mission statement: ‘to tailor the morphology, complex dielectric structure, and electronic properties of matter so as to sculpt the flow of sunlight and heat, enabling light conversion to electrical energy with unprecedented efficiency’. Founded in 2009, the LMI-EFRC has become a national resource for fundamental optical principles and phenomena relevant to solar energy conversion, addressing new scientific opportunities that enable efficient utilization of the entire visible and infrared solar resource. The LMI-EFRC is directed by Prof. Ralph Nuzzo and centered at its lead institution, the California Institute of Technology. The Center is an integrated and collaborative partnership of research leaders in photonics and photonic materials, comprising 14 faculty investigators that span six academic departments at five institutions, including Profs. Harry Atwater, Andrei Faraon, Nathan Lewis, and Austin Minnich at Caltech; Profs. Ralph Nuzzo, Paul Braun and John Rogers at the University of Illinois at Urbana-Champaign; Prof. Jennifer Lewis at Harvard University; Profs. Mark Brongersma, Jennifer Dionne, and Shanhui Fan at Stanford University; and Profs. Paul Alivisatos, Eli Yablonovitch, and Xiang Zhang at Lawrence Berkeley National Laboratory. The Center is organized into four research groups (RGs) that address scientific themes related to light-matter interactions, with each team spanning multiple institutional partners and designed to meet our scientific objectives. Notable project outcomes that address the LMI Mission and 2014-2018 goals include: (1) RG1 “New Light Management Mechanisms” demonstrated tunable and active nanostructured patterned surfaces (‘metasurfaces’) for control of light absorption, reflection, and propagation. (2) RG2 “Solar Spectrum Control and Conversion” developed colloidal nanocrystals with designer optical properties for fundamental studies of solar spectrum control and conversion. (3) RG3 “Thermal Photon Harvesting” established photonic design principles to harness and control thermal photons in novel conversion systems. (4) RG4 “Programmable Assembly of Photonic and Electronic Architectures” developed powerful new methods for light- and matter-based additive fabrication of electronic and photonic architectures.

14 SOLAR ENERGY↗

The Surface Chemistry of Methanol on Cu 3 Pd(111): Effects of Metal Alloying and Reaction with Hydrogen

Synchrotron-based ambient-pressure X-ray photoelectron spectroscopy (AP-XPS) was used to study the adsorption and surface chemistry of methanol on a Cu 3 Pd(111) model surface. The composition and morphological properties of the pristine Cu 3 Pd(111) substrate were analyzed using a combination of low-energy electron diffraction (LEED), scanning tunneling microscopy (STM), and low-energy ion scattering (LEIS). The results of ion scattering showed segregation of Pd toward the surface, with a Pd/Cu ratio close to 0.5, a larger value than the ratio of 0.33 expected for a Cu 3 Pd bimetallic structure. The surface of the alloy exhibited a good LEED pattern with three-fold long-range periodicities. In STM, clusters of palladium with hexagonal arrays and Pd- Pd distances of 2.7-2.8 Å were detected. Bonding to copper perturbed the electronic properties of the atoms in the Pd clusters, shifting their 4d states toward higher binding energy with respect to the Fermi level. Further, the valence band spectrum of Cu 3 Pd(111) exhibited a line shape that was very different from those displayed by Cu(111) or Pd(111). At low pressures, the adsorption of methanol on Cu 3 Pd(111) at 300 K mainly produced CH 3 O, CO and CH x species. AP-XPS showed that most Pd atoms in the surface of the Cu 3 Pd(111) alloy interacted with the decomposition products of methanol. No significant changes were observed in the core levels of copper upon the adsorption and dissociation of methanol, suggesting that the molecule mainly interacted with Pd sites of the alloy. Reaction with hydrogen led to fast removal of CH x , C and PdC x species from Cu 3 Pd(111) at moderate (< 450 K) temperatures and prevented a CH x → C transformation. If the stability of adsorbed CH 3 O is used as a descriptor for the hydrogenation of CO 2 to methanol, Cu 3 Pd should be a much better catalyst than monometallic palladium. This may be a consequence of electronic and ensemble effects in the alloy that moderate the reactivity of Pd sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Evolution of size-selected Pt cluster catalysts on prototypical oxide supports

The current quest for new pathways into sustainable, efficient and durable energy conversion technologies makes the used for a fundamental understanding of the atomic-scale phenomena underlying catalytic processes ever more pressing. In this context, characterizing catalyst particles in situ provides valuable information about the evolution of their composition, structure, oxidation state and charge state during an ongoing process. To disentangle the influence of individual parameters – temperature, pressure, gas composition, cluster size, as well as support acidity, redox state and defect density – it is crucial to control them precisely and separately in experiments. At the example of size-selected Pt n clusters – i.e. sub-nm particles defined to the exact number of atoms – on flat oxide supports, we follow their rich evolution phenomena via (synchrotron-based) X-ray photoelectron spectroscopy (XPS) and scanning tunnelling microscopy (STM) during temperature ramps and in various gas environments. Here, we present our experience with these highly defined, yet complicated-to-create samples in ultra-high vacuum (UHV) and at mbar pressures. We discuss their stability during transport to synchrotrons and under reaction conditions on three prototypical oxide supports and show the various phenomena that can be disentangled. Ptn clusters on the non-reducible silicon dioxide, SiO 2 , remain size-selected and show remarkable stability. Doping strongly influences the size-dependent binding energy shifts and changes the Pt response to oxidative and reaction conditions, which we attribute to different cluster geometries: p-type doping leads to wetting, enhanced sinter resistance and a diminished response to oxidative environments, compared to clusters on n-type doped samples. We compare the system with our previous findings of a similar change in dimensionality for Pt 20 clusters on the reducible ceria, CeO 2 (111), support, induced by modulation of its O vacancy density. The Pt n /CeO 2 system is particularly interesting for strategies to stabilize and redisperse Pt clusters dynamically. Finally, we study the evolution of Pt n clusters on another reducible oxide support, magnetite, Fe 3 O 4 (001), in 0.1 mbar alternating redox conditions at RT and elevated temperature. In analogy to findings previously reported for Pt/TiO 2 (110), the clusters either become encapsulated by a thin oxide film via strong metal–support interaction (SMSI) or deeply buried in the magnetite. Overall, our approach of following the evolution of size-selected clusters on oxide supports leads to fundamental atomic-scale insights on nano-scale catalyst materials, on our path to sustainable, dynamic and self-repairing catalysts.

Falling, Lorenz J. [Technical Univ. of Munich (Ger↗

Preliminary Compendium of the Initial Conditions and Evolution of the Fundamental Interactions of SiC with Ag and Pd

Tri-structural isotropic (TRISO) particles are the fuel of choice for very-high temperature reactors. At the core, these spherical particles consist of an inner fuel kernel of UO{sub 2}, UC{sub 2} or a combination of both, which is coated radially outward by successive layers of low density pyrolytic graphite, an inner high density pyrolytic graphite layer, silicon carbide (SiC) and an outer high density pyrolytic graphite layer. SiC is the main diffusion barrier against the release of fission products due to its hardness and high melting point. Irradiation testing of TRISO particles indicates that trace amounts of metallic fission products can damage or potentially escape through the barrier layer. Surrogate experimental studies have previously been performed by various methods seeking to shed light on and explain the diffusion behavior of Ag and Pd. Although some of these experiments have yielded realistic diffusion coefficients the discrepancy of results between different groups is such that the essential details of the diffusive behavior are still to be fully understood. This work aims to understand the fundamental physical and chemical interactions that take place at the interface of SiC and Ag/Pd, and which give rise to the observed diffusion behavior of these metallic species in TRISO particles. Theoretical simulations of the diffusion of Ag through SiC have been exhaustive but typically yield bulk diffusion coefficients that due to the nature of bulk diffusion phenomena (i.e. slow diffusion) the diffusion coefficients are calculated to be orders of magnitude lower than what experimental observations suggest. This in part is due to the difficulty in simulating realistic models that include various polymorphs of SiC, and the dynamical structural transformations that SiC undergoes in the TRISO environment (which are also to be explained). The result is a particularly challenging problem to solve given that the initial conditions of the interactions of Ag and Pd with SiC are difficult to address, both in theoretical models and surrogate experiments. In order to improve these models the approach taken here is to consider fundamental interactions between Ag and SiC that take place in short time scales by varying the initial environmental conditions, i.e. annealing temperature and time, initial amounts of the metallic species (M) Ag, Pd in SiC/M/SiC multilayers. This work aims to understand the fundamental physical and chemical interactions that take place at the interface of SiC and Ag/Pd, and which give rise to the observed diffusion behavior of these metallic species in TRISO particles. In order to do so we have synthesized SiC/Ag/SiC and SiC/Pd/SiC multilayers of various thicknesses by PLD and characterized them using SEM/EDS. Initial results show that upon annealing Ag agglomerates and ruptures the SiC layer to be released. In the case of Pd a strong chemical interaction is deduced from the slow interlayer diffusion and limited release. Further studies using photoelectron spectroscopy and RHEED will be carried out in order obtain detailed information on the chemical and physical transitions that undergo upon annealing of these systems. (authors)

36 MATERIALS SCIENCE↗

Calcium is associated with specific soil organic carbon decomposition products at Blodgett Forest Research Center, Georgetown, California as analysed with scanning transmission X-ray microscopy carbon near-edge X-ray absorption fine structure spectroscopy

This data is from the paper calcium is associated with specific soil organic carbon decomposition products, published in SOIL. DOI: https://doi.org/10.5194/soil-11-381-2025, 2025.This file contains CSVs with spectral data and bulk soil data and there is no specific program required to open this data. The data includes Scanning transmission X-ray microscopy carbon near-edge X-ray absorption fine structure spectroscopy. data from the measurement of samples from the Whole-soil Warming project, run by the Belowground Biogeochemistry team at Blodgett Forest Research Center, Georgetown, California run by the University of California, Berkeley. It also includes bulk soil chemical properties. The University of California's Blodgett Forest Research Station (Forest) is situated in the Sierra Nevada foothills (1370 m a.s.l.) near Georgetown, California. The samples were collected from here: 38.912013, -120.661469, https://maps.app.goo.gl/291bCJ1zVqUhgktz6. The Forest soils were characterised as Alfisols, which are equivalent to Dystric Cambisols (IUSS Working Group WRB, 2015), and formed in granitic parent materials, in a temperate climate, under thinned, mixed-coniferous forest (Fig. S3; Gaudinski et al., 2009). With these analyses we aimed to answer the question, is calcium associated with a specific type of organic matter enriched in aromatic and phenolic carbon at the microscale in samples from Blodgett Forest Research Center? and how does this specific type of carbon respond to experiments targetted at removing and adding calcium to the soils, specifically cation exchange and incubation after calcium addition? Abstract from the paper can be found below: Calcium (Ca) may contribute to the preservation of soil organic carbon (SOC) in more ecosystems than previously thought. Here we provide evidence that Ca is co-located with SOC compounds that are enriched in aromatic and phenolic groups, across different acidic soil-types and locations with different ecosystem properties, differing in terms of climate, parent material, soil type, and vegetation. In turn, this co-localised fraction of Ca-SOC is removed through cation-exchange, and the association is then only re-established during decomposition in the presence of Ca (Ca addition incubation). Thus, highlighting a causative link between decomposition and the co-location of Ca with a characteristic fraction of SOC. Decomposition increases the relative proportion of negatively charged functional groups, which can increase the propensity for the association between SOC and Ca, and in turn, this association inhibits dissolved organic carbon export or further decomposition. We propose that this mechanism could be driven by Ca hotspots on the microscale shifting local decomposition processes and thereby explaining the colocation of Ca with SOC of a specific composition across different acidic soil environments. Incorporating this biogeochemical process into Earth System Models could improve our understanding, predictions, and management of carbon dynamics in soils, and account for their response to Ca-rich amendments.

54 ENVIRONMENTAL SCIENCES↗